SEARCH · Search NASA
Results for “microstructural organization”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Interplay between microstructure, defect states, and mobile charge generation in transition metal dichalcogenide heterojunctions
Two-dimensional transition metal dichalcogenides (2D-TMDCs) have gained attention for their promise in next-generation energy-harvesting and quantum computing technologies, but realizing these technologies requires a greater understanding of TMDC properties that influence their photophysics. To this end, we discuss here the interplay between TMDC microstructure and defects with the charge generation yield, lifetime, and mobility. As a model system, we compare monolayer-only and monolayer-rich MoS 2 grown by chemical vapor deposition, and we employ the TMDCs in Type-II charge-separating heterojunctions with semiconducting single-walled carbon nanotubes (s-SWCNTs). Our results suggest longer lifetimes and higher yields of mobile carriers in samples containing a small fraction of defect-rich multilayer islands on predominately monolayer MoS 2 . Compared to the monolayer-only heterojunctions, the carrier lifetimes increase from 0.73 μs to 4.71 μs, the hole transfer yield increases from 23% to 34%, and the electron transfer yield increases from 39% to 59%. We reach these conclusions using a unique combination of microwave photoconductivity (which probes only mobile carriers) along with transient absorption spectroscopy (which identifies spectral signatures unique to each material and type of photoexcited quasiparticle, but does not probe mobility). Overall, our results highlight the substantial changes in photophysics that can occur from small changes in TMDC microstructure and defect density, where the presence of defects does not necessarily preclude improvements in charge generation.
Permeation Properties of Disordered Metal-Organic Framework Membranes Made by Vapor Phase Ligand Treatment
Zeolitic imidazolate frameworks (ZIFs) are nanoporous molecular sieves offering exciting opportunities for membrane- and adsorption-based gas separations. The Tsapatsis group developed an all-vapor-phase ligand induced permselectivation (LIPS) method for the fabrication of ZIF nanocomposite membranes. The LIPS method consists of a combination of atomic layer deposition of a dense oxide inside the mesopores of a porous support followed by transformation of the dense oxide deposit to nanoporous ZIF by exposure to sublimated vapors of an imidazolate ligand. It enables the formation of thin nanocomposite films consisting of ZIF deposited inside pores with diameters smaller than 10 nm. Vapor-phase conversion of the impermeable ZnO to ZIF increases flux of certain gases more than others. Vapor phase linker/ligand treatment (VPLT) can further modify the properties of LIPS and other membranes. The combination of LIPS with VPLT provides an all-vapor methodology for making and modifying ZIF membranes with the ability to control the ZIF deposit composition and the level of confinement in a variety of mesoporous supports. The propylene/propane separation performance of LIPS/VPLT ZIF membranes confined (entirely or partially) inside mesopores is remarkably superior to that of most conventional ZIF membranes consisting of unconfined (deposited on the external surface of porous supports) polycrystalline films. The accomplishments of this award are: (i) understanding of the LIPS process using mathematical models of atomic layer deposition (ALD), (ii) development of surface modification methods (vapor, e-beam, plasma, and X-ray treatments) to tune permeation properties, (iii) microstructural control of ZIF-8 films using ALD (support modification, direct ALD, and by use of in situ permeability monitoring), (iv) molecular simulations, and (v) thin film characterization and adsorption measurements using spectroscopy.
Room Temperature Electrorefining of Rare Earth Metals from End-of-use Nd-Fe-B Magnets
Recovering rare earth elements (REE) from used permanent magnets, which contains about 30 wt.% of rare earth elements, has been persistent technological challenge. Current recycling methods relies on pyrometallurgical or hydrometallurgical processes which are energy- and chemical- intensive and not economically and environmentally viable for rare earth containing magnets. Enabling efficient and simplistic recovery and refining of REEs contained in End-of-Use (EoU) products, such as Neodymium-Iron-Boron (Nd-Fe-B) based magnets will play an important and complementary role in the total supply of REEs in the future. We designed a new electrochemical method and demonstrated a room temperature one-pot process that concurrently separates and electroplates REE from commercial Nd-Fe-B magnets. By establishing selective oxidation and reductive potential as electrochemical control parameter along with electrochemically compatible non-aqueous electrolyte system, we demonstrated selective electroleaching of lanthanides (Nd and Preseodymium (Pr)) from anode and concurrent plating as alloy at Pt cathode. The morphological and chemical evolution of the Nd-Fe-B magnets during electroleaching reveals the electrochemical stimuli and rate of dissolution depends on microstructural complexities of the Nd-Fe-B magnet. The concomitant electroplating process leads to Nd-Pr based alloy which can be used as raw metallic alloy for manufacturing new permanent magnet and other devices. Our study demonstrates a scalable separation and refining methodology, based on widely available organic electrolyte system and without any consumptive chemical use, for selective lanthanide recovery from waste magnets.
Effect of lot microstructure variations on detonation performance of the triaminotrinitrobenzene (TATB)-Based insensitive high explosive PBX 9502
PBX 9502 is an important insensitive high explosive due to its combination of safety properties and detonation performance. It is a polymer-bonded formulation consisting of 95 wt.% 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) as the high explosive crystal, bound with Kel F-800 (FK-800), a co-polymer of chlorotrifluoroethylene and vinylidene-fluoride. Two different types are used, one known as virgin that uses only pristine manufactured TATB, and a second known as recycled that has 50 wt.% of its TATB reclaimed from machining scraps of previously pressed virgin PBX 9502. Recycled lots have a higher percentage of fine particles compared to virgin lots, due to the fracturing and damage sustained by TATB crystals during pressing. We examine the influence that this TATB microstructure difference between virgin and recycled PBX 9502 has on detonation performance properties. New rate-stick geometry diameter effect, detonation front shape and cylinder expansion test data are obtained for two previously uncharacterized virgin lots and one recycled lot of PBX 9502. This is combined with previously published data for one virgin and one recycled lot for evaluation purposes. Detonation shock dynamics model calibrations are conducted on each of the five lots to provide an assessment of the detonation timing characteristics of virgin versus recycled PBX 9502 lots. For two of the virgin lots, detonations propagate slower in the rate-stick geometry than those in the two recycled lots. However, the other virgin lot tested has propagation rates comparable to that of the recycled lots for larger diameter rate-sticks. The latter result, though, is shown to be geometry dependent and depends on the range of detonation curvatures accessed in different geometries. New copper-confined, cylinder expansion tests are conducted on each of the three virgin and two recycled lots to obtain detonation product Jones-Wilkins-Lee equations of state, enabling an assessment of the metal push capabilities for each of the five lots. We find that the metal push capabilities, characterized by the evolution of the heat of detonation with volume, are similar between the virgin and recycled lots. Thus, changes in microstructure between different PBX 9502 lots seemingly affect the rate of reaction, but not the overall energy content.
Indirect electrochemical method for high accuracy quantification of protein adsorption on gold surfaces
We demonstrate the use of copper underpotential deposition (UPD) for measurement of the electrochemically active surface area of a protein-modified gold electrode. The kinetics of adsorption and the subsequent structural rearrangement of β-casein, as a model protein, on the surface of a gold electrode have been followed over time. The protein-free surface area was determined by measuring the charge derived from UPD copper deposition on the non-blocked surface area at different stages of adsorption. The behaviour of β-casein adsorption as a function of surface roughness and the microstructure of the gold electrode, as well as the concentration of the protein solution, are studied using this method.
Structural evolution during gelation of pea and whey proteins envisaged by time-resolved ultra-small-angle x-ray scattering (USAXS)
Hydrogels from plant proteins commonly exhibit inferior gel strength compared to those from dairy proteins partially due to their distinct gel networks. How protein aggregates to form such networks in response to heat remains largely unknown. In this work, pea (PPI) and whey (WPI) protein isolate gels were produced at the same protein content and similar heating/cooling rate. The process was monitored using rheology, microscopy and in situ ultra-small-angle x-ray scattering (USAXS). Rheology showed an initial decrease in G' and G'' in PPI followed by a steady increase when the temperature surpassed ~60 °C whereas a much higher temperature (~80 °C) was required for WPI, both using 2 °C/min heating rate. Microscopy showed a coarse and heterogenous network in PPI, whereas for WPI, the network was finer and more continuous. In both gels, nano-sized spherical or ellipsoidal particles were present as the basic constituents. USAXS found individual protein was dominant in PPI or WPI solution at temperature below 57 °C. Their proportions decreased together with appearance of aggregates with an average R g of 9–10 nm in PPI and 6–7 nm in WPI at higher temperature. The size of the aggregates changed slightly during further heating and cooling, but their proportions increased. Power law exponents revealed the aggregates were mass fractals for WPI and PPI gels, and they became more compact during heating. Our findings suggested formation of primary aggregates in protein gel networks is a more organized process and provided theoretical guidance for production of high protein food gels with desirable texture.
Mechanistic understanding of microstructure formation during synthesis of metal oxide/carbon nanocomposites
In situ analysis of physicochemical processes occurring during pyrolysis synthesis of a TMO/C nanocomposite, including microstructure analysis via (S)TEM. Characterization of materials as electrodes for lithium intercalation and conversion reactions.
Chemo-Mechanically Driven In Situ Hierarchical Structure Formation in Mixed Conductors (Final Technical Report)
This document is the Final Technical Report for the Early Career project DE-SC0018963. Essential materials for energy technologies tend to exhibit “hierarchical” functions – they perform multiple, inter-related tasks at different locations, across disparate length and time scales. To best support this heterogeneous function, there is a fundamental need to understand and direct formation of corresponding tailored hierarchical architectures. In particular, a wide variety of applications, from energy conversion and storage to sensing and gas separation, rely on oxide mixed ionic and electronic conductors (MIECs). These critical ceramic materials catalyze reactions at their surfaces and selectively transport both ionic and electronic species in the bulk. Ideally, MIECs should adopt hierarchical structures with 1) high surface areas, 2) surface compositions exhibiting high catalytic activity, and 3) microstructural connectivity in the direction needed for fast mass and charge transport. In practice, however, MIECs.
Binder systems and methods for tape casting lithium garnet electrolytes
Slurry compositions, tape casting binder systems and fabrication methods for the fabrication of lithium-garnet electrolyte scaffolds for use in solid state batteries and other devices are provided. Slurry compositions may be optimized mixtures of LLZO powder, a dispersant, a lithium salt, a wetting agent a binder, a plasticizer and at least one solvent. The optimized ceramic slurry compositions may include MgO as a sintering additive to improve density and ionic conductivity of the doped-LLZO sheets and produce a fine-grained microstructure. Sintering protocols for cast slurries of commercially available doped LLZO powders eliminate the requirement of mother-powder coverings or externally applied pressure. An environmentally friendly water-based system using methylcellulose as a binder is also provided producing green tape and final properties comparable to those obtained with organic solvent-based systems.
Stochasticity at Scales Leads to Lithium Intercalation Cascade
Porous intercalation electrodes are synonymous with the promise of lithium-ion batteries toward electromobility. These electrodes exhibit stochastic geometrical features spanning different length scales. The implication of microstructural inhomogeneity on the lithium intercalation dynamics is hitherto unknown. In this work, starting from three-dimensional (3D), X-ray tomograms of intercalation electrode microstructures, we characterize the microstructural variability in porous intercalation electrodes. Furthermore, a physics-based analysis of electrochemical response reveals that the stochastic features can cause preferential lithiation fronts.
Hydroxyapatite/TiO 2 Nanomaterial with Defined Microstructural and Good Antimicrobial Properties
Due to the growing number of people infected with the new coronavirus globally, which weakens immunity, there has been an increase in bacterial infections. Hence, knowledge about simple and low-cost synthesis methods of materials with good structural and antimicrobial properties is of great importance. A material obtained through the combination of a nanoscale hydroxyapatite material (with good biocompatibility) and titanium dioxide (with good degradation properties of organic molecules) can absorb and decompose bacteria. In this investigation, three different synthesis routes used to prepare hydroxyapatite/titanium dioxide nanomaterials are examined. The morphology and semiquantitative chemical composition are characterized by scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX). The obtained materials’ phase and structural characterization are determined using the X-ray powder diffraction method (XRD). The crystallite sizes of the obtained materials are in the range of 8 nm to 15 nm. Based on XRD peak positions, the hexagonal hydroxyapatite phases are formed in all samples along with TiO 2 anatase and rutile phases. According to SEM and TEM analyses, the morphology of the prepared samples differs depending on the synthesis route. The EDX analysis confirmed the presence of Ti, Ca, P, and O in the obtained materials. The IR spectroscopy verified the vibration bands characteristic for HAp and titanium. The investigated materials show excellent antimicrobial and photocatalytic properties.
Nonfused Nonfullerene Acceptors with an A–D–A'–D–A Framework and a Benzothiadiazole Core for High-Performance Organic Solar Cells
Nonfullerene acceptors (NFAs) have contributed significantly to the progress of organic solar cells (OSCs). However, most NFAs feature a large fused-ring backbone, which usually requires a tedious multiple-step synthesis, and are not applicable to commercial applications. An alternative strategy is to develop nonfused NFAs, which possess synthetic simplicity and facile tunability in optoelectronic properties and solid-state microstructures. In this work, we report two nonfused NFAs, BTCIC and BTCIC-4Cl, based on an A-D-A'-D-A architecture, which possess the same electron-deficient benzothiadiazole central core but different electron-withdrawing terminal groups. The optical properties, energy levels, and molecular crystallinities were finely tuned by changing the terminal groups. Moreover, a decent power conversion efficiency of 9.3 and 10.5% has been achieved by BTCIC and BTCIC-4Cl, respectively, by blending them with an appropriate polymer donor. These results demonstrate the potential of A-D-A'-D-A type nonfused NFAs for high-performance OSCs. Further development of nonfused NFAs will be very fruitful by employing appropriate building blocks and via side-chain optimizations.
Pressure and thermal annealing effects on the photoconversion efficiency of polymer solar cells
This paper presents the results of experimental and theoretical studies of the effects of pressure and thermal annealing on the photo-conversion efficiencies (PCEs) of polymer solar cells with active layers that consist of a mixture of poly(3-hexylthiophene-2,5-diyl) and fullerene derivative (6,6)-phenyl-C 61 -butyric acid methyl ester. The PCEs of the solar cells increased from ~2.3% (for the unannealed devices) to ~3.7% for devices annealed at ~150 °C. A further increase in thermal annealing temperatures (beyond 150 °C) resulted in lower PCEs. Further improvements in the PCEs (from ~3.7% to ~5.4%) were observed with pressure application between 0 and 8 MPa. However, a decrease in PCEs was observed for pressure application beyond 8 MPa. The improved performance associated with thermal annealing is attributed to changes in the active layer microstructure and texture, which also enhance the optical absorption, mobility, and lifetime of the optically excited charge carriers. The beneficial effects of applied pressure are attributed to the decreased interfacial surface contacts that are associated with pressure application. The implications of the results are then discussed for the design and fabrication of organic solar cells with improved PCEs.
Baseplate Temperature–Dependent Vertical Composition Gradient in Pseudo–Bilayer Films for Printing Non–Fullerene Organic Solar Cells
Numerous previous reports on the sequential deposition (SD) technique have demonstrated that this approach can achieve a p–i–n active layer architecture with an ideal vertical composition gradient, which is one of the critical factors that can influence the physical processes that determine the photovoltaic performance of organic solar cells. Herein, a commonly used photovoltaic system comprised of PM6 as a donor and Y6 as an acceptor is investigated with respect to sequential blade–processing deposition to comprehensively explore the morphology characteristics as a function of baseplate temperature. A systematic study of the temperature–dependent blend morphology elucidates the SD–processed configuration merits and device physics behind temperature–controlled degree of vertical composition gradient, and constructs the temperature–microstructure–property relationship for the corresponding photovoltaic parameters. The result shows, as the temperature increases, the morphology of the active layer has undergone a distinct evolution from the pseudo–bulk heterojunction to a pseudo–planar heterojunction and then to a pseudo–planar bilayer, leading to a non–monotonic correlation between baseplate temperature and device performance. Further, this investigation not only reveals the importance of precisely controlling baseplate temperature for gaining vertical morphology control, but also provides a path toward rational optimization of device performance in the lab–to–fab transition.
Propagation of Input Uncertainties in Numerical Simulations of Laser Powder Bed Fusion
Laser powder bed fusion has the potential of redefining state-of-the-art processing and production methods, but defect formation and inconsistent build quality have limited the implementation of this process. Numerical models are widely used to study this process and predict the formation of these defects. Presently, the uncertainties of model input parameters and thermophysical properties used by these numerical simulations have not been investigated. In the present study, the uncertainty in these input parameters and material properties are quantified for laser powder bed fusion, with and without a simulated powder bed, to determine their influence on the predictive accuracy of an experimentally validated numerical model. Accounting for all possible sources of uncertainty quickly becomes computationally expensive on account of the curse of dimensionality. Uncertainty in laser absorption, solid, and liquid specific heat of the metal were found to have the largest effect on model prediction reliability with or without the use of a powder bed. Results also illustrate that accounting for these three uncertain parameters still captures the majority of model prediction uncertainty. Furthermore, the methodology of this study may be used to understand the uncertainty in as-built microstructure through propagation to microstructure prediction models, or applied under processing conditions where high Péclet numbers are observed and the thermal convection and fluid flow within the molten pool are substantial.
Applications of plasma-enhanced metalorganic chemical vapor deposition
The use of plasma enhancement for growth of III-V compound semiconductor materials by metalorganic chemical vapor deposition (MOCVD) is examined, to improve control of microstructure, develop understanding of the underlying growth mechanisms, and expand the range of materials combinations for photovoltaic and solid-state lighting applications. Whereas plasma is commonly used with group-IV materials, such as silicon, few studies have examined the impact of plasma-enhanced MOCVD (PE-MOCVD) for III-V materials growth. PE-MOCVD provides improved decomposition of metalorganic precursors, which is driven by hydrogen plasma to augment hydride reactions and thermal pyrolysis, but plasma generation requires low reactor pressure. We have demonstrated elemental Al films grown by PE-MOCVD, which show distinct crystallographic texturing, and assume epitaxial microstructure upon post-growth annealing. We also demonstrate PE-MOCVD of GaAs at temperatures as low as 300 °C. With increasing radio-frequency power, the GaAs growth rate shows a transition from power limited to mass-transport limited. PE-MOCVD grown Ga 0.5 In 0.5 P shows no detectable spontaneous atomic ordering, which offers a mechanism to form order/disorder unicompositional heterostructures, without temperature change or impurity incorporation. In its current implementation, PE-MOCVD grown films have shown microstructural degradation, that we attribute to direct plasma exposure during growth. Improvements in the system design and growth sequences are at the focus of on-going efforts.
Electrochemical Characterization and Microstructure Evolution of Ni-Rich Layered Cathode Materials by Niobium Coating/Substitution
Not Available