Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Investigations on microstructure, mechanical properties and abrasion resistance of 4wt%Cr-2wt%Mn-2wt%Cu-Fe-B alloy

Highlights: • The microstructure mainly consists of martensite and boride (M{sub 2}B) in the as-cast and heat treated Fe-B alloys, and the M{sub 2}B presents 3D-skeleton continuous-distribution. • After heat treatment, the nucleation and precipitation of secondary borocarbide M{sub 23}(C, B){sub 6} probably take place in an in situ manner within martensite. • The matrix hardness and bulk hardness of Fe-B alloy decrease after heat treatment, this is attributed to the decreasing of B/C concentration of matrix caused by the precipitation of M{sub 23}(C, B){sub 6}. • During the two-body wear process, the wear mechanism of Fe-B alloy is microcutting; with decreasing of hardness of Fe-B alloy, the abrasion resistance of Fe-B alloy decreases, i.e. the heat treatment will decrease the abrasion resistance of Fe-B alloy. - Abstract: The microstructure, mechanical properties and abrasion resistance of Fe-B alloy with 4wt%Cr-2wt%Mn-2wt%Cu addition have been systematically investigated. The results show that the microstructures mainly consist of martensite and boride (M{sub 2}B) in the as-cast and heat treated Fe-B alloys; after heat treatment, the morphology and volume fraction of the M{sub 2}B have little change, meanwhile the nucleation and precipitation of secondary borocarbide M{sub 23}(C, B){sub 6} probably take place in an in situ manner within martensite. Moreover, the M{sub 2}B is identified as chemical formula of Fe{sub 2.04}Cr{sub 0.11}Mn{sub 0.07}(B, C) reflecting body-centred tetragonal (bct) structure, and the secondary borocarbide M{sub 23}(B, C){sub 6} has the stoichiometry of Fe{sub 18.84}Cr{sub 2.84}Mn{sub 0.57}(B, C){sub 6} with face-centred cubic (fcc) structure. After heat treatment, the matrix hardness and bulk hardness of Fe-B alloy decrease owing to the decreasing of B/C concentration of matrix caused by the precipitation of M{sub 23}(C, B){sub 6}, while the fracture toughness of Fe-B alloy increases. Meanwhile, the heat treatment will decrease the wear resistance of Fe-B alloy, i.e. the wear resistance of Fe-B alloy would decrease with reduction of the matrix hardness.

36 MATERIALS SCIENCE↗

Effects of Heat Treatment on Microstructure, Mechanical Properties, Corrosion Resistance and Cytotoxicity of ZM21 Magnesium Alloy as Biomaterials

The effects of heat treatment on microstructure, mechanical properties, corrosion resistance and cytotoxicity of extruded Mg-2Zn-1Mn (wt.%) alloy were investigated for biomedical application in this study. The extruded alloy was T4 treated at 510 °C for 4 h and T5 treated at 200 °C for 16 h separately. The extruded Mg-Zn-Mn alloy mainly consists of Mg{sub x}Mn{sub y} phases. After T4 treatment, the amount of Mg{sub x}Mn{sub y} phases decreases and average grain size rises from 8 to 24 μm. After T5 treatment, Mg{sub 7}Zn{sub 3} phase newly precipitates along the grain boundaries and the size of grain remains similar. Compared with the T4-treated samples, the extruded and T5-treated samples exhibit higher mechanical properties. The T5-treated samples have an ultimate tensile stress of 273 MPa and an elongation of 19.7%. On the other hand, T4-treated samples present higher corrosion resistance in electrochemical tests. The degradation rates of extruded, T4-treated and T5-treated samples are 0.44 mm/year, 0.48 mm/year and 0.50 mm/year, respectively, in Ringer’s solution at 37 ± 0.2 °C. In addition, T4-treated alloy does not induce toxicity to the L-929 cells in in vitro cytotoxicity test.

36 MATERIALS SCIENCE↗

Effects of friction stir processing and minor Sc addition on the microstructure, mechanical properties, and damping capacity of 7055 Al alloy

Highlights: • Good mechanical and damping properties were obtained in the 7055 after FSP and Sc addition. • The strengthening and damping mechanisms of FSP 7055(-Sc) were analyzed. • FSP and Sc addition were found to be strategy of preparing 7xxx alloys with well damping and mechanical properties. - Abstract: This study investigated the effects of friction stir processing (FSP) and addition of 0.25% (mass ratio) Sc on the microstructure, mechanical properties, and damping capacity of AA 7055 alloy. Microstructure analyses revealed that a low tool rotation rate of 300 rpm effectively inhibited the grain coarsening in the recrystallization of the alloy during FSP. Sc addition prevented the coarsening of grains and precipitated η phase and the annihilation of dislocations in the FSP AA 7055 alloy. After being subjected to FSP at 300 rpm, the AA 7055 alloy containing Sc exhibited good mechanical and damping properties, which were mainly attributed to the fine recrystallized grain structure, fine precipitated η phase, and large number of nano-sized Al{sub 3}(Sc, Zr) particles located at the grain boundaries and dislocations. This work provides an effective strategy for preparing commercial Al alloys with excellent damping capacity and mechanical properties.

36 MATERIALS SCIENCE↗

Microstructure and property tailoring of castable nanostructured alloys through thermomechanical treatments

Three types of microstructures, i.e., tempered-martensite (TM), ferrite (F), and dual-phase (TM + F), were developed in a castable nanostructured alloy that favors a high density of nanoprecipitates compared with the precipitates in current reduced-activation ferritic-martensitic steels. The effect of the distinct microstructures on tensile properties, Charpy impact toughness, and thermal helium desorption behavior was investigated with the full TM structure as a reference. The results indicated that the F domain in the TM + F structure governed the strength and slightly impaired the impact toughness. The full F structure exhibited the highest strength without compromising ductility, but it noticeably diminished impact toughness. All microstructures had a dominant helium desorption peak at ~1070 °C. The higher density of nanoprecipitates and complex boundaries and dislocations in the TM + F structure enhanced the secondary helium desorption peak and extended the shoulder peak, in contrast to the full TM structure with an enlarged desorption peak associated with the ferrite-to-austenite transformation at ~810–850 °C and the full F structure with a dominant desorption peak related to bubble migration at ~1070 °C. These results suggest that components fabricated from functionally graded microstructures could be engineered to exploit the advantages of different microstructures for demanding application requirements.

36 MATERIALS SCIENCE↗

Effect of the Ce Content on the Magnetic Properties and Microstructure of CeCo{sub 5}-based Sintered Bulk Magnets

CeCo{sub 5}-based magnets have recently attracted much attention due to their moderate magnetic performance and low cost. Nevertheless, there have been few studies on the effects of Ce content on the magnetic properties and microstructures of CeCo{sub 5}-based magnets. In response to this, the magnetic properties of sintered bulk magnets with nominal compositions of Ce(Co{sub 0.73}Cu{sub 0.135}Fe{sub 0.135}){sub z} (z = 4.95, 5.15, 5.35, and 5.55), prepared by the conventional powder metallurgy method, were investigated here. Based on experimental findings, it was shown that Ce(Co{sub 0.73}Cu{sub 0.135}Fe{sub 0.135}){sub 5.15} sintered bulk magnets had comprehensive magnetic properties—maximum energy product of 80 kJ m{sup − 3} (10 MGOe) and intrinsic coercivity (H{sub cj}) of 452 kA m{sup − 1} (5.69 kOe)—superior to those previously reported by us. For z = 5.35 and 5.55, due to the presence of the minor Ce{sub 2}Co{sub 17} phase (which has a Curie temperature (T{sub c}) < 20 °C), magnets had low H{sub cj} values. Based on x-ray diffraction and scanning electron microscopy observations, it was suggested that the volume fraction of the 1:5 matrix phase was the main factor determining the H{sub cj} of CeCo{sub 5}-based sintered bulk magnets obtained with different Ce contents. Furthermore, the importance of the dispersion characteristics of the Ce{sub 2}O{sub 3} phase within the matrix was emphasized. Uniform dispersion of the Ce{sub 2}O{sub 3} phase can significantly improve the overall magnetic performance of CeCo{sub 5}-based magnets.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Heat Treatment Effects on the Tensile Properties and Microstructures of a SiC/RBSN Composite in Nitrogen

The room-temperature tensile properties and constituent microstructures of a unidirectionally reinforced SiC/reaction bonded silicon nitride (RBSN) composite have been investigated after heat treatments at 1400, 1600, or 1800 C in nitrogen for up to 100 hr. The composite consisted of approximately 24 vol% of aligned 140 micron diameter, continuous length, chemically vapor deposited SiC fibers in an approximately 40% porous silicon nitride matrix. The composites heat treated at 1400 C for up to 100 hr showed elastic modulus, first matrix cracking strength, and ultimate tensile strength values similar to those of the as-fabricated composites, but those heat treated for 1 hr beyond this temperature displayed losses in all three properties. Recrystallization of the SiC fibers, reaction between the carbon-rich interface coating on the fibers and the RBSN matrix, and dissociation of the RBSN matrix are the reasons for the loss of mechanical properties.

Bhatt, R. T.↗

Enhanced Surface Properties and Microstructure Evolution of Cr12MoV Using Ultrasonic Surface Rolling Process Combined with Deep Cryogenic Treatment

In this study, the enhanced surface properties and microstructure evolution of quenched and tempered cold work die steel Cr12MoV, which were induced by ultrasonic surface rolling process combined with deep cryogenic treatment (UDCT), were systematically investigated. The results indicated that UDCT had an advantage over conventional ultrasonic surface rolling process (USRP) in improving surface mechanical properties, including smaller surface roughness and smoother machined surface with less cracks and defects; higher surface microindentation hardness with the value of ~ 890 HV (increased by ~ 6.2% compared with USRP); and lower friction coefficient. Such enhancements in surface properties are mainly attributed to the martensitic transformation of retained austenite, the dispersion strengthening of small secondary carbides and the homogenized carbides distribution during UDCT.

36 MATERIALS SCIENCE↗

Effect of Electropulsing-Assisted Ultrasonic Nanocrystalline Surface Modification on the Surface Mechanical Properties and Microstructure of Ti-6Al-4V Alloy

The effect of electropulsing-assisted ultrasonic nanocrystalline surface modification (EP-UNSM) on surface mechanical properties and microstructure of Ti-6Al-4V alloy is investigated. Compared to conventional ultrasonic nanocrystalline surface modification (UNSM), EP-UNSM can effectively facilitate surface roughness and morphology, leading to excellent surface roughness (reduced from Ra 0.918 to Ra 0.028 μm by UNSM and Ra 0.019 μm by EP-UNSM) and smoother morphology with less cracks and defects. Surface friction coefficients are enhanced, resulting in lower and smoother friction coefficients. In addition, the surface-strengthened layer and ultra-refined grains are significantly enhanced with more severe plastic deformation and a greater surface hardness (a maximum hardness value of 407 HV and an effective depth of 550 μm, in comparison with the maximum hardness value of 364 HV and effective depth of 300 μm obtained by conventional UNSM). Remarkable enhancement of surface mechanical properties can be attributed to the refined gradient microstructure and the enhanced severe plastic deformation layer induced by coupling the effects of UNSM and electropulsing. The accelerated dislocation mobility and atom diffusion caused by the thermal and athermal effects of electropulsing treatment may be the primary intrinsic reasons for these improvements.

36 MATERIALS SCIENCE↗

Tensile Properties and Microstructure of Inconel 718 Fabricated with Electron Beam Freeform Fabrication (EBF(sup 3))

Electron beam freeform fabrication (EBF3) direct metal deposition processing was used to fabricate two Inconel 718 single-bead-width wall builds and one multiple-bead-width block build. Specimens were machined to evaluate microstructure and room temperature tensile properties. The tensile strength and yield strength of the as-deposited material from the wall and block builds were greater than those for conventional Inconel 718 castings but were less than those for conventional cold-rolled sheet. Ductility levels for the EBF3 material were similar to those for conventionally-processed sheet and castings. An unexpected result was that the modulus of the EBF3-deposited Inconel 718 was significantly lower than that of the conventional material. This low modulus may be associated with a preferred crystallographic orientation resultant from the deposition and rapid solidification process. A heat treatment with a high solution treatment temperature resulted in a recrystallized microstructure and an increased modulus. However, the modulus was not increased to the level that is expected for Inconel 718.

Bird, R. Keith↗

Effects of Postweld Heat Treatment on Microstructure and Properties of Laser-Welded Ti-24Al-15Nb Alloy Joint

The microstructure evolution and mechanical properties of laser-welded joints of Ti-24Al-15Nb alloy under different postweld heat treatment (PWHT) conditions were systematically investigated. The results show that the microstructure is very sensitive to PWHT temperatures. The weld zone consists of B2 and O phases after PWHT. With the PWHT temperatures increasing from 850 to 1000 °C, the amount of O phase decreases gradually, while the grains of O precipitates become coarser. After PWHT, there are some thin acicular O precipitates in heat-affected zone (HAZ), and the decomposition of α{sub 2}-phase caused by niobium diffusion can be observed in the HAZ. The PWHT can significantly increase the microhardness of joints, resulting from O phase precipitation hardening effect. The tensile strength and elongation of joints can be remarkably improved after PWHT, which was closely related to the strengthening effect of O precipitates and slip transmission between O and B2 phases. In addition, the results indicate that the best mechanical properties can be achieved only when the number and size of O phase and B2 phase are the best match.

36 MATERIALS SCIENCE↗

Effect of tube processing methods on microstructure, mechanical properties and irradiation response of 14YWT nanostructured ferritic alloys

In this research, innovative thermal spray deposition (Process I) and conventional hot extrusion processing (Process II) methods have been used to produce thin walled tubing (~0.5 mm wall thickness) out of 14YWT, a nanostructured ferritic alloy. The effects of processing methods on the microstructure, mechanical properties and irradiation response have been investigated by using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and, micro- and nano-hardness techniques. It has been found that these two processes have a significant effect on the microstructure and mechanical properties of the as-fabricated 14YWT tubes. Even though both processing methods yield the formation of various size Y-Ti-O particles, the conventional hot extrusion method results in a microstructure with smaller, homogenously distributed nano-oxides (NOs, Y-Ti-O particles < 5 nm) with higher density. Therefore, Process II tubes exhibit twice the hardness of Process I tubes. It has also been found that these two tremendously different initial microstructures strongly affect irradiation response in these tubes under extremely high dose ion irradiations up to 1100 peak dpa at 450 °C. The finer, denser and homogenously distributed NOs in the Process II tube result in a reduction in swelling by two orders of magnitude. On the other hand, inhomogeneity of the initial microstructure in the Process I tube leads to large variations in both swelling and irradiation induced hardening. Moreover, hardening mechanisms before and after irradiation were measured and compared with detailed calculations. In conclusion, this study clearly indicates the crucial effect of initial microstructure on radiation response of 14YWT alloys.

36 MATERIALS SCIENCE↗

ASSESSMENT OF THE STATE OF PRECIPITATION IN ALUMINUM CASTING A356.2 ALLOY USING NONDESTRUCTIVE MICROSTRUCTURE ELECTRONIC PROPERTY MEASUREMENTS

Application of nondestructive electronic property measurements to assess the strengthening of Mg{sub 2}Si precipitates in aluminum A356.2 casting has been demonstrated. The results indicated the evolution of precipitation phase through over aging with increased cooling time or thickness of the cast part. The classical optimum precipitation behavior has been characterized and verified with thermal analysis, thermoelectric power, low frequency impedance, and micro hardness measurements. A proposed practice to use nondestructive electronic property measurement tools to assess aluminum casting for acceptable mechanical properties after mold shake out is presented.

36 MATERIALS SCIENCE↗

Effects of Rolling Temperature on the Microstructure and Properties of 2Cr13/316L/9Cr18MoV Stainless Steel Composite Plate Fabricated by Hot-Rolling Bonding Process

A 15-layer composite plate was developed. The microstructure and mechanical properties were characterized by scanning electron microscopy, Vickers microhardness, tensile, and bending tests. Particularly, the effects of hot-rolling at different rolling temperatures of 1130, 1180, 1250, and 1300 °C on the microstructure and mechanical properties of the 2Cr13/316L/9Cr18MoV composite plates were investigated in detail. The results indicated that, with the increase in the rolling temperature, the tensile strength was first decreased and then slightly increased by the coarsening of grains and the increase in the ferrite content in the 2Cr13 layers. The highest tensile elongation of 12.5% and tensile strength of 958.1 MPa were obtained for the composite plate manufactured with the rolling temperature of 1180 °C. The 2Cr13/316L/9Cr18MoV composite plates with rolling temperatures of 1130 and 1180 °C obtained by hot-rolling processes withstood larger bending deformations, showing only local cracks after the bending process because of their strong combined interfaces. However, during the bending to 130° of specimens fabricated with the rolling temperature of 1250 and 1300 °C, the specimens experienced direct fracture at very low bending displacements.

36 MATERIALS SCIENCE↗

Fabrication, Microstructures, and Properties of 50 vol.% SiCp/6061Al Composites via Hot Pressing

Nearly fully dense 50 vol.% SiCp/6061Al composites were fabricated via hot pressing (HPing) at temperatures ranging from 610 to 650 °C, with the axial load and holding time fixed as 25 MPa and 120 min, respectively. The interfacial reactions, microstructures, and properties of the SiCp/Al alloy were studied. The interface reaction between SiCp and the Al alloy was suppressed at annealing temperatures of 620 °C and below; however, the reaction intensified as the annealing temperature increased, producing Al{sub 4}C{sub 3}, Si, and Mg{sub 2}Si. With an increase in HPing temperature from 610 to 630 °C, the 6061Al alloy melted and gradually filled the pores in the SiC particles under the applied load. The density, bending strength, and thermal conductivity (TC) of the composites increased, whereas the coefficient of thermal expansion (CTE) of the composites decreased. With an increase in HPing temperature increased from 630 to 650 °C, the 6061Al alloy melt leaked through the sintered bodies, resulting in the microstructural degradation and property reduction of the composites. The 50 vol.% SiCp/6061Al composites fabricated by HPing at 630 °C exhibited optimal comprehensive properties [bending strength, 332.4 MPa; TC, 186.3 W(m K){sup −1}; and CTE, 7.9 × 10{sup −6}/°C (20-100 °C)], which were attributed to the highest relative density and the best SiCp/Al interfacial structure of the composites.

36 MATERIALS SCIENCE↗

The Effect of Interlayer Delay on the Heat Accumulation, Microstructures, and Properties in Laser Hot Wire Directed Energy Deposition of Ti-6Al-4V Single-Wall

Laser hot wire directed energy deposition (LHW-DED) is a layer-by-layer additive manufacturing technique that permits the fabrication of large-scale Ti-6Al-4V (Ti64) components with a high deposition rate and has gained traction in the aerospace sector in recent years. However, one of the major challenges in LHW-DED Ti64 is heat accumulation, which affects the part quality, microstructure, and properties of as-built specimens. These issues require a comprehensive understanding of the layerwise heat-accumulation-driven process–structure–property relationship in as-deposited samples. In this study, a systematic investigation was performed by fabricating three Ti-6Al-4V single-wall specimens with distinct interlayer delays, i.e., 0, 120, and 300 s. The real-time acquisition of high-fidelity thermal data and high-resolution melt pool images were utilized to demonstrate a direct correlation between layerwise heat accumulation and melt pool dimensions. The results revealed that the maximum heat buildup temperature of the topmost layer decreased from 660 °C to 263 °C with an increase to a 300 s interlayer delay, allowing for better control of the melt pool dimensions, which then resulted in improved part accuracy. Furthermore, the investigation of the location-specific composition, microstructure, and mechanical properties demonstrated that heat buildup resulted in the coarsening of microstructures and, consequently, the reduction of micro-hardness with increasing height. Extending the delay by 120 s resulted in a 5% improvement in the mechanical properties, including an increase in the yield strength from 817 MPa to 859 MPa and the ultimate tensile strength from 914 MPa to 959 MPa. Cooling rates estimated at 900 °C using a one-dimensional thermal model based on a numerical method allowed us to establish the process–structure–property relationship for the wall specimens. The study provides deeper insight into the effect of heat buildup in LHW-DED and serves as a guide for tailoring the properties of as-deposited specimens by regulating interlayer delay.

36 MATERIALS SCIENCE↗

Microstructure, Mechanical Properties, Hot-Die Forming, and Joining of 47XD Gamma TiAl Rolled Sheets

The microstructure and mechanical properties, along with the hot-die forming and joining of Ti-47Al-2Nb-2Mn-0.8 vol% TiB, sheets (known as 47XD), produced by a low-cost rolling process, were evaluated. A near-gamma microstructure was obtained in the as-rolled condition. The microstructures of heat-treated sheets ranged from a recrystallized equiaxed near-gamma microstructure at 1,200 to 1,310 C, to a duplex microstructure at 1,350 C, to a fully lamellar microstructure at 1,376 C. Tensile behavior was determined for unidirectionally rolled and cross-rolled sheets for room temperature (RT) to 816 C. Yield stress decreased gradually with increasing deformation temperature up to 704 C; above 704 C, it declined rapidly. Ultimate tensile strength exhibited a gradual decrease up to 537 C before peaking at 704 C, followed by a rapid decline at 816 C. The modulus showed a gradual decrease with temperature, reaching approximately 72% of the RT value at 816 C. Strain to failure increased slowly from RT to 537 C; between 537 C and 704 C it exhibited a phenomenal increase, suggesting that the ductile-brittle transition temperature was below 704 C. Fracture mode changed from transgranular fracture at low temperature, to a mixture of transgranular and intergranular fracture at intermediate temperature, to ductile fracture at 816 C, coupled with dynamic recrystallization at large strains. Creep rupture response was evaluated between 649 and 816 C over the stress range of 69 to 276 MPa. Deformation parameters for steady-state creep rate and time-to-rupture were similar: activation energies of approximately 350 kJ/mol and stress exponents of approximately 4.5. Hot-die forming of sheets into corrugations was done at elevated temperatures in vacuum. The process parameters to join sheets by diffusion bonding and brazing with TiCuNi 70 filler alloy were optimized for test coupons and successfully used to fabricate large truss-core and honeycomb structures. Nondestructive evaluation methods, e.g., ultrasonic C-scans and thermography along with metallography, were used to characterize bond quality. Microstructural evaluation during heat treatment, identification of phases at the braze/matrix interface, determination of shear strengths of brazed joints, and deformation mechanisms during tensile and creep processes will be discussed.

Das, G.↗

Microstructure, magnetic properties and exchange-coupling interactions for one-dimensional hard/soft ferrite nanofibers

SrFe{sub 12}O{sub 19} (SFO)/Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} (NZFO) composite ferrite nanofibers with diameters about 120 nm have been prepared by the electrospinning and calcination process. The SFO/NZFO composite ferrites are formed after calcined at 700 Degree-Sign C for 2 h and the composite nanofibers with various mass ratios obtained at 900 Degree-Sign C are fabricated from NZFO grains about 16-40 nm and SFO grains of 19-45 nm with a uniform phase distribution. With the SFO ferrite content increasing, the coercivity (H{sub c}) and remanence (M{sub r}) for the composite ferrite nanofibers initially increase, reaching maximum values of 379.8 kA/m (297 K) and 242.2 kA/m (77 K), 39.1 Am{sup 2}/kg (297 K) and 53.5 Am{sup 2}/kg (77 K), respectively, at a mass ratio (SFO:NZFO) of 4, and then show a reduction tendency with a further increase of the mass ratio. This enhancement in magnetic properties is attributed to the competition of the exchange-coupling interaction and the dipolar interaction in the composite nanofibers. - Graphical abstract: SrFe{sub 12}O{sub 19} (SFO)/Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} (NZFO) composite ferrite nanofibers with a uniform phase distribution show competition of the exchange-coupling interaction and the dipolar interaction in the composite nanofibers. Highlights: Black-Right-Pointing-Pointer Composite ferrite nanofibers have been prepared by the electrospinning. Black-Right-Pointing-Pointer Magnetic exchange-coupling interaction for these nanofibers were analyzed. Black-Right-Pointing-Pointer Nanofibers magnetic properties measured at 297 K and 77 K were discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗