SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The determination of latent heat-flux variability using spaceborne sensors is discussed. Particular attention is given to the microwave sensors which have all weather capability. The retrieval of surface layer humidity, of wind speed and interfacial humidity, and of sensible heat flux are discussed. Both the indirect retrieval and direct retrieval of latent heat flux are considered.
Results of the in-flight calibration and performance evaluation campaign for the TOPEX/POSEIDON microwave radiometer (TMR) are presented. Intercomparisons are made between TMR and various sources of ground truth, including ground-based microwave water vapor radiometers, radiosondes, global climatological models, special sensor microwave imager data over the Amazon rain forest, and models of clear, calm, subpolar ocean regions. After correction for preflight errors in the processing of thermal/vacuum data, relative channel offsets in the open ocean TMR brightness temperatures were noted at the approximately = 1 K level for the three TMR frequencies. Larger absolute offsets of 6-9 K over the rain forest indicated a approximately = 5% gain error in the three channel calibrations. This was corrected by adjusting the antenna pattern correction (APC) algorithm. AS 10% scale error in the TMR path delay estimates, relative to coincident radiosondes, was corrected in part by the APC adjustment and in part by a 5% modification to the value assumed for the 22.235 FGHz water vapor line strength in the path delay retrieval algorithm. After all in-flight corrections to the calibration, TMR global retrieval accuracy for the wet tropospheric range correction is estimated at 1.1 cm root mean square (RMS) with consistent peformance under clear, cloudy, and windy conditions.
The validation of sea ice products derived from the Special Sensor Microwave Imager (SSM/I) on board a DMSP platform is examined using data from the Landsat MSS and NOAA-AVHRR sensors. Image processing techniques for retrieving ice concentrations from each type of imagery are developed and results are intercompared to determine the ice parameter retrieval accuracy of the SSM/I NASA-Team algorithm. For case studies in the Beaufort Sea and East Greenland Sea, average retrieval errors of the SSM/I algorithm are between 1.7 percent for spring conditions and 4.3 percent during freeze up in comparison with Landsat derived ice concentrations. For a case study in the East Greenland Sea, SSM/I derived ice concentration in comparison with AVHRR imagery display a mean error of 9.6 percent.
Sensitivity requirements of the various measurements obtained by microwave sensors, and radiometry techniques are described. Analytical techniques applied to detailed sharing analyses are discussed. A bibliography of publications pertinent to the scientific justification of frequency requirements for passive microwave remote sensing is included.
Passive and active microwave remote sensing data are analyzed to identify signatures of precipitation and vertical motion in tropical convection. A database of cloud/radiative model simulations is used to quantify surface rain rates and latent heating profiles that are consistent with these signatures. At satellite footprint-scale (approximately 10 km), rain rate and latent heating estimates are subject to significant random errors, but by averaging the estimates in space and time, random errors are substantially reduced, Bias errors have been minimized by improving the microphysics in the supporting cloud/radiative model simulations, and by imposing a consistent definition of remotely-sensed and model-simulated convective/stratiform rain coverage. Remotely-sensed precipitation and latent heating distributions in the tropics are derived from Tropical Rainfall Measuring Mission (TRMM) and Special Sensor Microwave/ Imager (SSM/ I) sensor data. The prototype Version 6 TRMM passive microwave algorithm typically yields average heating profiles with maxima between 6 and 7 km altitude for organized mesoscale convective systems. Retrieved heating profiles for individual convective systems are compared to coincident estimates based upon a combination of dual-Doppler radar and rawinsonde data. Also, large-scale latent heating distributions are compared to estimates derived from a simpler technique that utilizes observations of surface rain rate and stratiform rain proportion to infer vertical heating structure. Results of these tests will be presented at the conference.
A satellite-based system to monitor global precipitation on monthly and shorter time scales is described. The monitoring system is based primarily on the Global Precipitation Climatology Project (GPCP) global, monthly, 2.5 degree by 2.5 degree latitude-longitude product which utilizes precipitation estimates from low-orbit microwave sensors (SSM/I) and geosynchronous IR sensors and raingauge information over land. The low-orbit microwave estimates are used to adjust or correct the geosynchronous IR estimates, thereby maximizing the utility of the more physically-based microwave estimates and the finer time sampling of the geosynchronous observations. Information from raingauges is blended into the analyses over land. This globally complete, monthly product is available from January 1986 to the present, with an extension back to January 1979 underway using non-SSM/I data. The monthly GPCP merged data product described in the previous paragraph is available a few (2-4) months after the end of the month. An analysis based solely on low-orbit microwave (SSM/1) data and the Goddard Profiling (GPROF) algorithm is used to bring the global monitoring up to real time. Anomalies from climatological means are produced from both the GPCP and GPROF fields to monitor the evolution of global precipitation, including the calculation of ENSO precipitation indices for real-time (five- day running means) climate monitoring and comparison with previous ENSO anomalies. The long-term climatology of the global precipitation field and the time and space variations thereof will be discussed, including the variations associated with the 1997- 1998 ENSO. The GPCP fields will also be compared to analyses based on the recently launched Tropical Rain Measuring Mission (TRMM). On an even shorter time scale, a new daily, 1 degree x 1 degree latitude-longitude global analysis has been developed starting in January 1997 utilizing low-orbit microwave and geosynchronous IR information using a similar method as is used to produce the monthly GPCP product. Retaining the overall small bias of the monthly product the daily product will allow greater utilization in the hydrology and other science communities.
The science need for remotely sensed soil moisture has been well established in the hydrologic, climate change and weather forecasting communities. There also have been a number of programs that have demonstrated the feasibility of using long wave microwave sensors for estimating soil moisture. These have ranged from truck mounted sensors, to intensive airborne campaigns with science objectives. Based on this history of truck and aircraft experiments, the science community has settled on a soil moisture product that meets the following criteria: a two day global repeat, a measured layer of 5 cm of soil, a footprint of 20 to 30 km, and an absolute accuracy of +/- 4% volumetric soil moisture. The principal sensor to accomplish this is an L-band passive microwave radiometer. A soil moisture mission is being proposed for the NASA Earth Systems Science Pathfinder (ESSP) mission which has very real constraints of a limited budget which includes the launch vehicle, and a three year award to launch time schedule. This paper describes ways to solve the very large antenna challenge, and the criteria used to choose the final design for an ESSP proposal. The paper also discusses the alternatives considered to obtain the necessary ancillary data for characterizing the surface roughness, the surface temperature and the attenuation affects of vegetation.
A new 20-year, monthly, globally complete precipitation analysis has been completed as part of the World Climate Research Program's (WCRP/GEWEX) Global Precipitation Climatology Project (GPCP). The global, monthly, 2.5 deg x 2.5 deg latitude-longitude product utilizes precipitation estimates from low-orbit microwave sensors (SSM/1) and geosynchronous IR sensors and raingauge information over land. The low-orbit microwave estimates are used to adjust or correct the geosynchronous IR estimates, thereby maximizing the utility of the more physically-based microwave estimates and the finer time sampling of the geosynchronous data. The 20-year climatology of the Version 2 GPCP analysis indicates the expected features of a very strong Pacific Ocean ITCZ and SPCZ with maximum 20-year means approaching 10 mm/day. A similar strength maximum over land is evident over Borneo. Weaker maxima in the tropics occur in the Atlantic ITCZ and over South America and Africa. In mid-latitudes of the Northern Hemisphere the Western Pacific and Western Atlantic maxima have values of approximately 7 mm/day, while in the Southern Hemisphere the mid-latitude maxima are located southeast of Africa, in mid-Pacific as an extension of the SPCZ and southeast of South America. In terms of global totals the GPCP analysis shows 2.7 mm/day (3.0 mm/day over ocean; 2.1 mm/day over land), similar to the Jaeger climatology, but not other climatologies. Zonal averages peak at 6 mm/day at 7 deg N with mid-latitude peaks of about 3 mm/day at 40-45 deg latitude. Poleward of 45 deg the GPCP analysis shows larger zonally-averaged values than most previous satellite-based estimates, although the values are similar to the Jaeger climatology.
A new 20-year, monthly, globally complete precipitation analysis has been completed as part of the World Climate Research Program's (WCRP/GEWEX) Global Precipitation Climatology Project (GPCP). This Version 2 of the community generated data set is a result of combining the procedures and data sets as described. The global, monthly, 2.5x 2.5 degree latitude-longitude product utilizes precipitation estimates from low-orbit microwave sensors (SSM/1) and geosynchronous IR sensors and raingauge information over land. The low-orbit microwave estimates are used to adjust or correct the geosynchronous IR estimates, thereby maximizing the utility of the more physically-based microwave estimates and the finer time sampling of the geosynchronous observations. Information from raingauges is blended into the analyses over land. In the 1986-present period TOVS-based precipitation estimates are adjusted to GPCP fields and used in polar regions to produce globally-complete results. The extension back to 1979 utilizes the procedures of Xie and Arkin and their OLR Precipitation Index (OPI). The 20-year climatology of the Version 2 GPCP analysis indicates the expected features of a very strong Pacific Ocean ITCZ and SPCZ with maximum 20-year means approaching 10 mm/day. A similar strength maximum over land is evident over Borneo. Weaker maxima in the tropics occur in the Atlantic ITCZ and over South America and Africa. In mid-latitudes of the Northern Hemisphere the Western Pacific and Western Atlantic maxima have values of approximately 7 mm/day, while in the Southern Hemisphere the mid-latitude maxima are located southeast of Africa, in mid-Pacific as an extension of the SPCZ and southeast of South America. In terms of global totals the GPCP analysis shows 2.7 mm/day (3.0 mm/day over ocean; 2.1 mm/day over land), similar to the Jaeger climatology, but not other climatologies. Zonal averages peak at 6 mm/day at 7*N with mid-latitude peaks of about 3 mm/day at 40-45* latitude. Poleward of 45* the GPCP analysis shows larger zonally-averaged values than most previous satellite-based estimates, although the values are similar to tl,ie Jaeger climatology. Over both ocean areas and at high latitudes the analysis requires additional validation and comparison with special, independent data sets from field experiments and from the Tropical Rain Measuring Mission (TRMM) to confirm the absolute magnitude and variations of precipitation seen in the analysis. Interannual and other variations of the global fields will be shown focusing on the recent ('97-'99) ENSO event compared with previous events, including teleconnections at mid and high latitudes. An ENSO Precipitation Index (ESPI) calculated using the new data set will be described and related to the evolution of the ENSO events during the 20-year period.
The Sea of Okhotsk, located between 50 and 60 N, is bounded by the Kamchatka Peninsula, Siberia, Sakhalin Island, and the Kuril Island chain and is the largest midlatitude seasonal sea ice zone in the Northern Hemisphere. The winter sea ice cover begins to form in November and expands to cover most of the sea by March. Over the following three months, the ice retreats with only small ice-covered areas remaining by the beginning of June. The sea is ice free or nearly ice free on average for six months of the year, from June through November. The recent compilation of a consistent, long-term record of Northern Hemisphere sea ice extents based on passive microwave satellite observations from the Nimbus 7 Scanning Multichannel Microwave Radiometer and from four Defense Meteorological Satellite Program Special Sensor Microwave Imagers provides the basis for assessing long-term sea ice extent variability in the Sea of Okhotsk. Analysis of this 20-year data record (1979-1998) shows that based on yearly averages the overall extent of the Sea of Okhotsk ice cover is decreasing at the rate of -8.1+/-2.1x10(exp 3) sq km/yr (-17.2%/decade), in contrast to the rate of decrease of -33.3+/-0.7x10(exp 3) sq km/yr (-2.7%/decade) for the Northern Hemisphere as a whole. There is large regional sea ice extent variability of the Arctic ice cover. Two of the nine Arctic regions analyzed, the Bering Sea and the Gulf of St. Lawrence, show increases of 0.8+/-1.4xl0(exp 3) sq km/yr (2.7%/decade) and 1.2+/-0.5xl0(exp 3) sq km/yr (17.1%/decade), respectively. Interestingly, the Sea of Okhotsk and the Gulf of St. Lawrence show about equal percentage changes, but of opposite sign. The Sea of Okhotsk exhibits its greatest percent decrease (-24.3%/decade) during spring (April-June). The year of maximum winter sea ice extent for the Sea of Okhotsk was 1979, whereas the minimum winter sea ice extent occurred in 1984.
Three-dimensional radar data for three summer Florida storms are used as input to a microwave radiative transfer model. The model simulates microwave brightness observations by a 19-GHz, nadir-pointing, satellite-borne microwave radiometer. The statistical distribution of rainfall rates for the storms studied, and therefore the optimal conversion between microwave brightness temperatures and rainfall rates, was found to be highly sensitive to the spatial resolution at which observations were made. The optimum relation between the two quantities was less sensitive to the details of the vertical profile of precipitation. Rainfall retrievals were made for a range of microwave sensor footprint sizes. From these simulations, spatial sampling-error estimates were made for microwave radiometers over a range of field-of-view sizes. The necessity of matching the spatial resolution of ground truth to radiometer footprint size is emphasized. A strategy for the combined use of raingages, ground-based radar, microwave, and visible-infrared (VIS-IR) satellite sensors is discussed.
Satellite observations of the cloud liquid water path (LWP) are compared from special sensor microwave imager (SSM/I) measurements and GOES 8 imager solar reflectance (SR) measurements to ascertain the impact of sub-field-of-view (FOV) cloud effects on SSM/I 37 GHz retrievals. The SR retrievals also incorporate estimates of the cloud droplet effective radius derived from the GOES 8 3.9-micron channel. The comparisons consist of simultaneous collocated and full-resolution measurements and are limited to nonprecipitating marine stratocumulus in the eastern Pacific for two days in October 1995. The retrievals from these independent methods are consistent for overcast SSM/I FOVS, with RMS differences as low as 0.030 kg/sq m, although biases exist for clouds with more open spatial structure, where the RMS differences increase to 0.039 kg/sq m. For broken cloudiness within the SSM/I FOV the average beam-filling error (BFE) in the microwave retrievals is found to be about 22% (average cloud amount of 73%). This systematic error is comparable with the average random errors in the microwave retrievals. However, even larger BFEs can be expected for individual FOVs and for regions with less cloudiness. By scaling the microwave retrievals by the cloud amount within the FOV, the systematic BFE can be significantly reduced but with increased RMS differences of O.046-0.058 kg/sq m when compared to the SR retrievals. The beam-filling effects reported here are significant and are expected to impact directly upon studies that use instantaneous SSM/I measurements of cloud LWP, such as cloud classification studies and validation studies involving surface-based or in situ data.
Special Sensor Microwave /Imager (SSM/I) observations in cloud systems are studied over the tropics. Over optically thick cloud systems, presence of polarized signatures at 37 and 85 GHz is evidenced and analyzed with the help of cloud top temperature and optical thickness extracted from visible and IR satellite observations. Scattering signatures at 85 GHz (TbV(85) less than or = 250 K) are associated with polarization differences greater than or = 6 K, approx. 50%, of the time over ocean and approx. 40% over land. In addition. over thick clouds the polarization difference at 37 GHz is rarely negligible. The polarization differences at 37 and 85 GHz do not stem from the surface but are generated in regions of relatively homogeneous clouds having high liquid water content. To interpret the observations, a radiative transfer model that includes the scattering by non-spherical particles is developed. based on the T-matrix approach and using the doubling and adding method. In addition to handling randomly and perfectly oriented particles, this model can also simulate the effect of partial orientation of the hydrometeors. Microwave brightness temperatures are simulated at SSM/I frequencies and are compared with the observations. Polarization differences of approx. 2 K can be simulated at 37 GHz over a rain layer, even using spherical drops. The polarization difference is larger for oriented non-spherical particles. The 85 GHz simulations are very sensitive to the ice phase of the cloud. Simulations with spherical particles or with randomly oriented non-spherical ice particles cannot replicate the observed polarization differences. However, with partially oriented non-spherical particles, the observed polarized signatures at 85 GHz are explained, and the sensitivity of the scattering characteristics to the particle size, asphericity, and orientation is analyzed. Implications on rain and ice retrievals are discussed.
By comparing data from the Special Sensor Microwave Imager (SSM/I) to field data, a melt threshold of the cross-polarized gradient ratio (XPGR), which is a normalized difference between the 19 GHz horizontally-polarized and 37 GHz vertically polarized brightness temperatures, is determined. This threshold, XPGR = -0.025, is used to classify dry and wet snow. The annual areal extent of melt is mapped for the years 1988 through 1991, and inter-annual variations of melt extent are examined. The results show that the melt extent varied from a low of 38.3% of the ice sheet (1990) to a high of 41.7% (1991) during the years 1988-1991.
The ability to monitor the structural health of the rotating components, especially in the hot sections of turbine engines, is of major interest to aero community in improving engine safety and reliability. The use of instrumentation for these applications remains very challenging. It requires sensors and techniques that are highly accurate, are able to operate in a high temperature environment, and can detect minute changes and hidden flaws before catastrophic events occur. The National Aeronautics and Space Administration (NASA) has taken a lead role in the investigation of new sensor technologies and techniques for the in situ structural health monitoring of gas turbine engines. As part of this effort, microwave sensor technology has been investigated as a means of making high temperature non-contact blade tip clearance, blade tip timing, and blade vibration measurements for use in gas turbine engines. This paper presents a summary of key results and findings obtained from the evaluation of two different types of microwave sensors that have been investigated for use possible in structural health monitoring applications. The first is a microwave blade tip clearance sensor that has been evaluated on a large scale Axial Vane Fan, a subscale Turbofan, and more recently on sub-scale turbine engine like disks. The second is a novel microwave based blade vibration sensor that was also used in parallel with the microwave blade tip clearance sensors on the experiments with the sub-scale turbine engine disks.
The development of new active tip clearance control and structural health monitoring schemes in turbine engines and other types of rotating machinery requires sensors that are highly accurate and can operate in a high temperature environment. The use of a microwave sensor to acquire blade tip clearance and tip timing measurements is being explored at the NASA Glenn Research Center. The microwave blade tip clearance sensor works on principles that are very similar to a short range radar system. The sensor sends a continuous microwave signal towards a target and measures the reflected signal. The phase difference of the reflected signal is directly proportional to the distance between the sensor and the target being measured. This type of sensor is beneficial in that it has the ability to operate at extremely high temperatures and is unaffected by contaminants that may be present in turbine engines. The use of microwave sensors for this application is a new concept. Techniques on calibrating the sensors along with installation effects are not well quantified as they are for other sensor technologies. Developing calibration techniques and evaluating installation effects are essential in using these sensors to make tip clearance and tip timing measurements. As a means of better understanding these issues, the microwave sensors were used on a bench top calibration rig, a large axial vane fan, and a turbofan. Background on the microwave tip clearance sensor, an overview of their calibration, and the results from their use on the axial vane fan and the turbofan will be presented in this paper.
Satellite remote sensing has provided powerful tools for constructing long-term records of observations of many of Earth's geophysical processes. Geophysicists studying climage change would like to construct time series of data which are as long, accurate, and consistent as possible. While technological advances continue to improve the quality of observations from space, they also present consistency problems. The scanning multichannel microwave radiometer (SMMR), which operated from October 1978 to August 1987, and the special sensor microwave imager (SSMI), which overlapped with the SMMR for nearly two months in 1987, have provided microwave radiances which have been used to monitor long-term changes in sea ice concentration and snow accumulation, among other things. Inspection has shown, however, that brightness temperatures from the two sensors over the same polar firn-covered scene can differ by as much as 14 K. Calibration corrections for polar firn have been derived; in this paper, we present calculations addressing the physics of the small frequency and viewing angle differences between the SMMR and the SSMI on microwave emission from polar scenes containing free water. We focus here only on surface emission. We use a surface scattering model and study the effects of surface roughness, snow wetness, snow density, and young sea ice concentration. We also compare data from Antarctica with our modeled results. We find that for most scenes, surface roughness dominates over the effects of frequency and viewing angle differences, but that for open long-term times series, data must be calibrated and constructed at the geophysical product level rather than at the level of measured radiances.
Research efforts during FY-88 have focused on completion of several projects relating to analysis of FGGE data during SOP-1 and on expanded studies of global atmospheric moisture. In particular, a revised paper on the relationship between diabatic heating and baroclinicity in the South Pacific Convergence Zone (SPCZ) was submitted. A summary of completed studies on diagnostic convective parameterization was presented at the Satellite Meteorology and Oceanography Convergence last February. These investigations of diabatic heating in the SPCZ have demonstrated the requirement for a more quantitative description of atmospheric moisture. As a result, efforts were directed toward use of passive remote microwave measurements from the Nimbus-7 SMMR and the DOD's Special Sensor Microwave Imager (SSMI/I) as critical sources of moisture data. Activities this year are summarized.