Results for “operational limits” — Page 10

NASA NTRS1972

Hydrogen-oxygen catalytic ignition and thruster investigation. Volume 1: Catalytic ignition and low pressure thruster evaluations

An experimental and analytical program was conducted to evaluate catalytic igniter operational limits, igniter scaling criteria, and delivered performance of cooled, flightweight gaseous hydrogen-oxygen reaction control thrusters. Specific goals were to: (1) establish operating life and environmental effects for both Shell 405-ABSG and Engelhard MFSA catalysts, (2) provide generalized igniter design guidelines for high response without flashback, and (3) to determine overall performance of thrusters at chamber pressures of 15 and 300 psia (103 and 2068 kN/sq m) and thrust levels of 30 and 1500 lbf, respectively. The experimental results have demonstrated the feasibility of reliable, high response catalytic ignition and the effectiveness of ducted chamber cooling for a high performance flightweight thruster. This volume presents the results of the catalytic igniter and low pressure thruster evaluations are presented.

Johnson, R. J.↗

NASA NTRSDate not supplied

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas Turbine↗

NASA NTRS2023

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas turbine↗

NASA NTRSDate not supplied

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas turbine↗

NASA NTRS2023

Considering Turbofan Operability in Hybrid Electric Aircraft Propulsion System Design

This paper explores the design of a hybrid electric aircraft propulsion system that uses a turbofan to power an electric system. In such a system, the gas turbine will experience a loss of power generation as altitude increases, however the electric system will not. This difference results in designs that may over size the electric system at high altitude or under size at low altitude. Two studies are performed within this paper. The first looks at extracting power from the engine for use with electric aircraft propulsion at cruise and the second reviews a design of an engine that uses thrust assist for takeoff. Both studies look at the effects of changing altitude on the amount of power extraction or insertion that can be taken from the turbofan as dictated by operability limits. Results of the paper show that low-pressure compressor surge margin and high-pressure compressor speed can be pushed to unaccepted limits with large scale power extraction or insertion, however these issues can be mitigated by adding power extraction or insertion at off design operating points to compensate. Additionally, the benefits of thrust assist are quantified for this configuration demonstrating a reduction in thrust specific fuel consumption at cruise of over 5%.

Gas Turbine↗

NASA NTRS1991

Resonance transition radiation X-ray laser

A free electron laser is proposed using a periodic dielectric and helical magnetic field. Periodic synchronism between the electrons and the optical wave is obtained at the period of the dielectric and not at the period of the helical magnetic field. The synchronism condition and the gain of the new device are derived. The effects on the gain from dephasing and beam expansion due to elastic scattering of the electrons in the periodic medium are included in the gain calculation. Examples of the resonance transition radiation laser and klystron are given. Operation at photon energies between 2.5 and 3.5 keV with net gain up to 12 percent is feasible using high electron-beam energies of 3 and 5 GeV. Moderate (300-MeV) beam energy allows operation between 80 to 110 eV with up to 57 percent net gain using a klystron design. In both cases, rapid foil heating may limit operation to a single electron-beam pulse.

Reid, Max B.↗

NASA NTRS1979

System design requirements for advanced rotary-wing agricultural aircraft

Helicopter aerial dispersal systems were studied to ascertain constraints to the system, the effects of removal of limitations (technical and FAA regulations), and subsystem improvements. Productivity indices for the aircraft and swath effects were examined. Typical missions were formulated through conversations with operators, and differing gross weight aircraft were synthesized to perform these missions. Economic analysis of missions and aircraft indicated a general correlation of small aircraft (3000 lb gross weight) suitability for small fields (25 acres), and low dispersion rates (less than 32 lb/acre), with larger aircraft (12,000 lb gross weight) being more favorable for bigger fields (200 acres) and heavier dispersal rates (100 lb/acre). Operator problems, possible aircraft and system improvements, and selected removal of operating limitations were reviewed into recommendations for future NASA research items.

Lemont, H. E.↗

DOE OSTI2022

Mitigating cerium migration for perfluorosulfonic acid membranes using organic ligands

Improving the electrochemical stability of proton exchange membranes is a pressing priority for heavy-duty fuel cell vehicles. The lifetime of the most widely used perfluorosulfonic acid membranes is limited by reactive free radicals generated inside the system. Cerium has been found to reduce the chemical degradation of the membranes. However, cerium migration during fuel cell operation limits the chemical durability enhancement effect expected from the radical scavenging activity of cerium. Here we investigate a wide range of organic immobilizers for cerium, measuring their suitability concerning cerium retention, radical scavenging activity, and fuel cell performance. Further, we report that partially fluorinated phosphonic acids enhance cerium retention up to 45 times and reduce fluoride emission rate by 38% compared to the commercial Nafion™ XL membrane pre-impregnated with cerium. The energetics of cerium-phosphonic acid complex systems by density functional theory calculations rationalizes effective cerium immobilization.

25 ENERGY STORAGE↗

DOE OSTI2022

Mitigating cerium migration for perfluorosulfonic acid membranes using organic ligands

Improving the electrochemical stability of proton exchange membranes is a pressing priority for heavy-duty fuel cell vehicles. The lifetime of the most widely used perfluorosulfonic acid membranes is limited by reactive free radicals generated inside the system. Cerium has been found to reduce the chemical degradation of the membranes. However, cerium migration during fuel cell operation limits the chemical durability enhancement effect expected from the radical scavenging activity of cerium. Here we investigate a wide range of organic immobilizers for cerium, measuring their suitability concerning cerium retention, radical scavenging activity, and fuel cell performance. We report that partially fluorinated phosphonic acids enhance cerium retention up to 45 times and reduce fluoride emission rate by 38% compared to the commercial Nafion™ XL membrane pre-impregnated with cerium. The energetics of cerium-phosphonic acid complex systems by density functional theory calculations rationalizes effective cerium immobilization.

30 DIRECT ENERGY CONVERSION↗

NASA NTRS1984

Tethered propellant resupply technique for space stations

One of the primary functions of the space station is related to the propellant resupply of orbital transfer vehicles, orbital maneuvering vehicles, and satellites. Difficulties arise in the case of an acquisition of cryogenic propellants by means of a use of zero-gravity techniques. The use of the 'tethered propellant resupply technique' is, therefore, considered. A study is being conducted to determine the feasibility, design requirements, and operational limitations of this technique. Attention is given to aspects of gravity feed, transfer method selection, requirements related to the orbital transfer vehicle, hazard clearance, attitude control, depot operations, end mass velocity, the microgravity laboratory, and concept evaluation activities.

Kroll, K. R.↗

DOE OSTI2025

ECAR-8446 Rev 0 MARVEL BPVC Section III Division 5 HBB Fatigue Acceptance Tests

The objective of this analysis is to evaluate the fatigue and creep behavior of 316 SS materials used in the Primary Coolant System (PCS) and Guard Vessel System (GVS) for the first two years of MARVEL reactor operation. The analysis follows the requirements set forth in ASME BPVC Section III, Division 5, HBB-2800, which mandates a fatigue test if operational conditions exceed allowable thresholds. By determining whether the materials meet the HBB-T-1324(a) and HBB-T-1324(b) criteria, this evaluation establishes whether a fatigue test is necessary, as well as the maximum allowable operational hours and temperatures before fatigue testing would be required. The deliverables of this analysis include calculations validating compliance with fatigue acceptance criteria, determination of maximum operational limits for the two-year period, and identification of conditions under which a fatigue test would be necessary. This ensures that the PCS and GVS can operate safely without premature material degradation and align with the design life requirements outlined in SPC-70731. Additionally, this evaluation provides conservative estimates for Service Level B occurrences and their impact on allowable Service Level A hours and temperatures, offering guidance for future operational assessments and potential life extensions beyond the initial two-year period.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗

DOE OSTI2026

Midwest ZEVI 2030 Charging Roadmap for I-80 Corridor

Zero-emission Medium Duty and Heavy Duty vehicles (MD-HD ZEVs) hold great promise for reducing operational costs through use of more energy eAicient propulsion technology while reducing reliance on fossil fuels. Consistent with the Department of Energy’s focus on energy innovation, ZEVs and the necessary charging and refueling infrastructure to support them represent an important area of focus for technological advancement. Widespread adoption of MD-HD ZEVs can also provide benefits by improving air quality, and lowering carbon emissions in the transportation industry. Powertrain technologies are in production today to reduce tank-to-wheel and well-to-wheel emissions of commercial vehicles to zero or near-zero emissions, but significant development remains to bring down the cost and address the operational limitations of these technologies, particularly for larger vehicles. ZEV technologies have an opportunity to be an important part of a fleet’s mix of powertrains as capital and operational costs come down. However, the greatest challenge preventing widespread adoption of ZEVs may be the lack of adequate charging and hydrogen (H₂) fueling infrastructure.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

DOE OSTI2021

Voltage Regulation Performance Evaluation of Distributed Energy Resource Management via Advanced Hardware-in-the-Loop Simulation

This paper evaluates the performance of coordinated control across advanced distribution management systems (ADMS), distributed energy resources (DERs), and distributed energy resource management systems (DERMS) using an advanced hardware-in-the-loop (HIL) platform. This platform provides a realistic laboratory testing environment, including accurate dynamic modeling of a real-world distribution system from a utility partner, real controllers (ADMS and DERMS), physical power hardware (DERs), and standard communications protocols. One grid service—voltage regulation—is evaluated to show the performance of the coordinated grid automation system. The testing results demonstrate that the coordinated DERMS and ADMS system can effectively regulate system voltages within target operation limits using DERs. The realistic laboratory HIL testing results give utilities confidence in adopting the grid automation systems to manage DERs to achieve system-level control and operation objectives (e.g., voltage regulation). This helps utilities mitigate potential risks (e.g., instability) prior to field deployment.

24 POWER TRANSMISSION AND DISTRIBUTION↗

NASA NTRS1979

Multivariable control altitude demonstration on the F100 turbofan engine

The control system designed under the Multivariable Control Synthesis (MVCS) program for the F100 turbofan engine is described. The MVCS program, applied the linear quadratic regulator (LQR) synthesis methods in the design of a multivariable engine control system to obtain enhanced performance from cross-coupled controls, maximum use of engine variable geometry, and a systematic design procedure that can be applied efficiently to new engine systems. Basic components of the control system, a reference value generator for deriving a desired equilibrium state and an approximate control vector, a transition model to produce compatible reference point trajectories during gross transients, gain schedules for producing feedback terms appropriate to the flight condition, and integral switching logic to produce acceptable steady-state performance without engine operating limit exceedance are described and the details of the F100 implementation presented. The engine altitude test phase of the MVCS program, and engine responses in a variety of test operating points and power transitions are presented.

Lehtinen, B.↗

NASA NTRSDate not supplied

Validation of Transient Spacecraft Refueling Model with Gateway Breadboard Test Data

The ability to refuel spacecraft on-orbit is a key enabling technology for deep space human exploration. On-orbit refueling requires priming a pressurized liquid propellant from a source tank into fluid transfer lines at vacuum conditions, which could result in excessive surge pressures beyond the system’s qualified operating limits and potentially damage hardware. Therefore, it is imperative to employ numerical models during the development of flight hardware to parametrically characterize system performance over a wide range of operating conditions. Since priming transients are difficult to model accurately, it is important to validate those models with test data. As part of the Gateway bipropellant refueling system development, a simplified fluidic breadboard system was created using water as a simulant for fuel to support early program risk reduction of refueling operations. The objectives of breadboard testing were to gather performance data to characterize and demonstrate critical refueling operations and to validate numerical models that can be extended to predicting flight system performance. A description of the breadboard test system and the results of numerical model validation is presented. The model is shown to have very good agreement with test data.

Brian S Lusby↗

NASA NTRS1987

Results of acoustic tests of a Prop-Fan model

Results of acoustic tests in a low speed open jet anechoic wind tunnel are presented for a counter rotation Prop-Fan model. The model tested had 5 front and 5 rear rotor blades with swept planform. Noise spectra are presented showing the influence of operating and configuration variables such as: (1) power absorption, (2) tip speed, (3) rotor-rotor spacing, (4) power split between the front and rear blade rows, (5) variation of the RPM ratio between front and rear blade rows, (6) tractor versus pusher (pylon effects), and (7) angle of attack. In addition to model scale results, calculated levels derived from test are presented showing the influence of the above variables on Effective Perceived Noise Level of a 13.1 ft diameter Prop-Fan at a flyover distance of 1500 ft. It was found that the strongest effects are caused by tip speed and power absorption. A significant finding was that there is an optimum operating tip speed for minimum noise for a given power absorption. Effects of other parametric variations are generally small but measurable. In order to minimize noise to meet airplane certification limits, operation at moderate tip speeds and power absorption is shown to be desirable. Accuracy of predicted Effective Perceived Noise Level is shown to be good with the best accuracy in the 590 to 670 ft/sec tip speed range.

Metzger, F.B.↗

NASA NTRS1990

The output beam quality of a Q-switched Nd:glass slab laser

The authors have constructed and tested a flashlamp pumped, Q-switched, Nd:glass zigzag slab laser. The thermally induced optical distortion through the slab is minimized by uniform pumping and cooling and the use of corrective pump shields at the slab ends. The laser spatial output for Q-switched resonators has been measured and modeled. It is shown that a larger aperture planar oscillator has an output divergence many times above the diffraction limit. Operation as a one-dimensional unstable resonator in the wide direction of the slab allows the efficient extraction of energy in a high-quality beam. Near-diffraction-limited laser output of 5 J at 4 Hz is achieved with a resonator that includes an intracavity telescope to correct for residual defocusing in the thin direction of the slab.

Reed, Murray K.↗

NASA NTRS1999

A Plasma Instability Theory of Gamma-Ray Burst Emission

A plasma instability theory is presented for the prompt radiation from gamma-ray bursts. In the theory, a highly relativistic shell interacts with the interstellar medium through the filamentation and the two-stream instabilities to convert bulk kinetic energy into electron thermal energy and magnetic field energy. The processes are not efficient enough to satisfy the Rankine-Hugoniot conditions, so a shock cannot form through this mechanism. Instead, the interstellar medium passes through the shell, with the electrons radiating during this passage. Gamma-rays are produced by synchrotron self-Compton emission. Prompt optical emission is also produced through this mechanism, while prompt radio emission is produced through synchrotron emission. The model timescales are consistent with the shortest burst timescales. To emit gamma-rays, the shell's bulk Lorentz factor must be $\simg 10(exp 3)$. For the radiative processes to be efficient, the interstellar medium density must satisfy a lower limit that is a function of the bulk Lorentz factor. Because the limits operate as selection effects, bursts that violate them constitute new classes. In particular, a class of optical and ultraviolet bursts with no gamma-ray emission should exist. The lower limit on the density of the interstellar medium is consistent with the requirements of the Compton attenuation theory, providing an explanation for why all burst spectra appear to be attenuated. Several tests of the theory are discussed, as are the next theoretical investigations that should be conducted.

Brainerd, Jerome J.↗