Search NASA⌕ Search

SEARCH · Search NASA

Results for “optical microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Neutron Diffraction Residual Stress Study of a AA2219-T87 Self-Reacting Friction Stir Weld

2219-T87 is a precipitation hardenable aluminum-copper alloy which sees wide use in structural aerospace components. Thick panels of this alloy are joined via self-reacting friction welding (SRFSW); however, this thermomechanical process can result in significant loss of the alloy’s strengthening precipitates and large residual stresses which are detrimental to mechanical behavior and performance. High-resolution maps of the residual strain and stress states along the normal, transverse, and longitudinal directions of 2219-T87 SRFSW were obtained using neutron diffraction measurements. Residual stress had the highest tensile value in the heat-affected zone (HAZ) and the largest compressive stress in the base metal region of the normal and transverse directions. Line profile residual stress distributions displayed an “M”-shaped distribution in each direction with the longitudinal direction being the most pronounced while 2D residual stresses displayed an hourglass-shaped pattern. Further, average maximal longitudinal residual stress values ranged from 60.6 to 85.6% of yield. Microhardness testing across the transverse weld section produced a “V”-shaped curve with slight hardness recovery in the stir zone. Maximal and minimal microhardness values were observed in the base metal (154 HV) and thermomechanically affected zone (82 HV), respectively. Microstructural evolution was recorded using optical microscopy and showed decreasing grain size from the HAZ to the stir zone.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Cladding and Butt-Joining Dissimilar Aluminum Alloys Simultaneously via Shear Assisted Processing and Extrusion

Shear assisted processing and extrusion has been used to fabricate multi-metallic tubing that incorporates regions with clad and butt-joined structures. In this work, aluminum alloys 6061, 7075, and 1100 are combined to create a monolithic extruded tubing with weldable ends (6061), a high strength center (7075), and a corrosion-resistant cladding (1100). Optical microscopy shows a gradual, defect-free, transition between alloys at the butt-joint interfaces and a sharp transition between alloys at the clad interface. Tensile testing proved the mechanical coherency of the joint, with failure occurring outside the tri-metallic structure. In conclusion, smoothed particle hydrodynamic simulations identified a spiral pattern of the cladding alloy that leads to inconsistent cladding thickness, and identified a simplified 2-alloy combination of aluminum alloys 6082 and 2014 that accomplished the design objectives of the tri-metallic structure.

Coatings↗
DOE OSTI2022

Microstructural Development in Inconel 718 Nickel-Based Superalloy Additively Manufactured by Laser Powder Bed Fusion

Excellent weldability and high temperature stability make Inconel 718 (IN718) one of the most popular alloys to be produced by additive manufacturing. Here in this study, we investigated the effects of laser powder bed fusion (LPBF) parameters on the microstructure and relative density of IN718. The samples were fabricated with independently varied laser power (125 - 350W), laser scan speed (200 - 2200 mm/s), and laser scan rotation (0° - 90°). Archimedes’ method, optical microscopy, and scanning electron microscopy were employed to assess the influence of LPBF parameters on the relative density and microstructure. Optimal processing windows were identified for a wide range of processing parameters and relative density greater than 99.5% was achieved using volumetric energy density between 50 and 100 J/mm3. Microstructural features including melt pool geometry, lack of fusion defect, keyhole porosity, and sub-grain cellular microstructure were examined and quantified to correlate to LPBF parameters. A simple empirical model was postulated to relate relative sample density and LPBF volumetric energy density. Melt pool dimensions were quantitatively measured and compared to estimations based on Rosenthal solution, which yielded a good agreement with the width, but underestimated the depth, particularly at high energy input, due to lack of consideration for keyhole mode. In addition, the sub-grain cellular-dendritic microstructure in the as-built samples was observed to decrease with increasing laser scan speed. Quantification of the sub-micron cellular-dendritic microstructure yielded estimated cooling rate in the order of 10 5 – 10 7 K/s.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Microstructural Coarsening Kinetics and Mechanical Property Changes in Long-Term Aged Sn–Pb–Sb Solder Joints

Tin-lead-antimony (50Sn–47Pb–3Sb wt.%) soldered assemblies were mechanically tested approximately 30 years after initial production and found to have solder joints of reduced strength. The microstructure of this solder alloy exhibits a ternary eutectic structure with Sn-rich, Pb-rich, and SnSb phases. Accelerated aging was performed to evaluate solder microstructural coarsening and associated strength of laboratory solder joints to correlate these properties to the “naturally aged” solder joints. Isothermal aging was conducted at room temperature, 55, 70, 100, and 135 °C and aging times that ranged from 0.1 to 365 days. The coarsening kinetics of the Pb-rich phase were determined through optical microscopy and image analysis methods established in previous studies on binary Sn–Pb solder. A kinetic equation was developed with time exponent n of 0.43 and activation energy of 24000 J/mol, suggesting grain boundary diffusion or other fast diffusion pathways controlling the microstructural evolution. Compression testing and Vickers microhardness showed significant strength loss within the first 20–30 days after soldering; then, the microstructure and mechanical properties changed more slowly over long periods of time. Further, by combining accelerated aging data and the microstructure-based kinetics, strength predictions were made that match well with the properties of the actual soldered assemblies naturally aged for 30 years. However, aging at the highest temperature of 135 °C produced anomalous behavior suggesting that extraneous aging mechanisms are active. Therefore, data obtained at this temperature or higher should not be used. Overall, the combined microstructural and mechanical property methods used in this study confirmed that the observed reduction in strength of ~ 30-year-old solder joints can be accounted for by the microstructural coarsening that takes place during long-term solid-state aging.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A New Method for Polishing Laminated Dissimilar Metals

Here, this paper presents a novel method for preparing metallographic samples of laminated dissimilar metals, specifically a layered structure of zirconium (Zr), vanadium (V), and tungsten (W), which pose a challenge due to their differing crystal structures and hardness levels. The work was motivated by the need to develop a cladding for tungsten targets in spallation neutron sources, where a zirconium face is applied over an interlayer of either vanadium or titanium to prevent the formation of brittle intermetallic compounds such as ZrW 2 . Traditional polishing techniques prove inadequate because each constituent metal requires a different polishing approach based on its unique material properties. The methodology outlined includes a sequential process involving conductive epoxy mounting, successive grinding and polishing with specific abrasives, and a final chemical-mechanical polish using a colloidal silica-based solution. Optical microscopy confirmed that this multi-step process successfully produced scratch-free surfaces and minimized surface relief across the different metal interfaces. Although developed for refractory metals, this approach shows promise for other layered structures comprised of transition metals, offering a meticulous yet effective technique for high-quality metallographic sample preparation.

Newberry, Daniel [Oak Ridge National Laboratory (O↗
DOE OSTI2023

A Workflow for Accelerating Multimodal Data Collection for Electrodeposited Films

Abstract Future machine learning strategies for materials process optimization will likely replace human capital-intensive artisan research with autonomous and/or accelerated approaches. Such automation enables accelerated multimodal characterization that simultaneously minimizes human errors, lowers costs, enhances statistical sampling, and allows scientists to allocate their time to critical thinking instead of repetitive manual tasks. Previous acceleration efforts to synthesize and evaluate materials have often employed elaborate robotic self-driving laboratories or used specialized strategies that are difficult to generalize. Herein we describe an implemented workflow for accelerating the multimodal characterization of a combinatorial set of 915 electroplated Ni and Ni–Fe thin films resulting in a data cube with over 160,000 individual data files. Our acceleration strategies do not require manufacturing-scale resources and are thus amenable to typical materials research facilities in academic, government, or commercial laboratories. The workflow demonstrated the acceleration of six characterization modalities: optical microscopy, laser profilometry, X-ray diffraction, X-ray fluorescence, nanoindentation, and tribological (friction and wear) testing, each with speedup factors ranging from 13–46x. In addition, automated data upload to a repository using FAIR data principles was accelerated by 64x.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Process-Structure-Property Relations for As-Deposited Solid-State Additively Manufactured High-Strength Aluminum Alloy

Solid-state additive manufacturing methods provide innovative solutions to circumvent problems associated with materials susceptible to hot cracking by avoiding liquid solid phase transformations. In this work, the process parameter influence on microstructural evolution and mechanical response of a fully dense aluminum alloy 7050 (AA7050) component manufactured via a rapid, solid-state additive manufacturing process known as Additive Friction Stir Deposition (AFS-D) was quantified for the first time. Three sections (starting dwell, transient, crossover of roads) of the deposition that exhibit differing thermomechanical processing histories were evaluated for the resulting microstructure and mechanical response. The microstructural characterization was performed on the as-deposited AA7050 via Electron Backscatter Diffraction (EBSD), TEM, optical microscopy, and Scanning Electron Microscopy (SEM). The microstructural characterization revealed refined constituent particles and grains throughout the as-deposited AA7050 microstructure. Furthermore, quasi-static tensile experiments were conducted in both the build and transverse directions, in order to quantify the orientation influence on tensile properties of the as-deposited AA7050 build. Spatially dependent tensile properties were observed in the material due to heat input variation coarsening of secondary phases towards the initial layers of the AFS-D build. Post-mortem analysis revealed that voids nucleated and coalesced from the overgrowth of the strengthening precipitates present in the material, resulting in fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Investigation of B 4 C for inhibiting crystallization in silica at high temperatures

Amorphous silica has numerous high temperature applications due to its inherent thermal shock resistance and low coefficient of thermal expansion (CTE). However, at the high temperatures required for processing (>1200 °C), the metastable β-cristobalite phase preferentially forms and is accompanied by a volume change, and potential cracking, upon conversion to the low temperature α-cristobalite phase. The CTE of the final crystalline phase is an order of magnitude higher than its amorphous counterpart. Here experimental results demonstrate that small additions of B 4 C (3.5 wt%) effectively inhibit silica crystallization in powder and sintered gel-cast forms up to 22h at temperatures as high as 1500°C as confirmed via x-ray diffraction. Further, the oxidation of B 4 C to B 2 O 3 and its subsequent melt and evaporation disrupts the nucleation and growth of the cristobalite phase. The mechanism for crystallization inhibition is further explored through optical microscopy to probe changes in surface morphology.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Surface evolution of synthetic bilgewater emulsion

Bilgewater is oil-in-water emulsion emitted from shipboard and it is a source of pollution to the ocean. Wastewater treatment needs fundamental knowledge of the bilgewater surface changes; however, limited information is available. We have reported the first surface characterization of synthetic bilgewater emulsion using time-of-flight secondary ion mass spectrometry (ToF-SIMS) coupled with optical microscopy. A NAVY synthetic bilgewater emulsion consisting of three oils and a detergent mixture is used as the synthetic bilgewater model. Both fresh and aged emulsion samples are analyzed to determine their droplet size distributions (DSDs) and surface chemical compositions. Our results show that fresh emulsions are largely mono-modal with hydrocarbon fragments as the main surface composition. Aged emulsions are also monomodal with slightly larger size. Both SIMS spectral comparison and Principal Component Analysis (PCA) show that some surfactant components appear on the fresh emulsion surface immediately while larger molecular weight components appear at the aged bilge droplet surface. Our results indicate that the oil-water interface evolves after emulsion droplet forms. More importantly, surface evolution not only changes the bilgewater DSD but also surface chemical composition and reactivity.

bilgewater, droplet size distribution, ToF-SIMS, s↗
DOE OSTI2023

Characterization of microstructure and residual stress following the friction stir welding of dissimilar aluminum alloys

Friction-stir-welding (FSW) has gained importance as an effective way to join dissimilar materials due to its solid-state nature. However, FSW produces substantial residual stresses in aluminum welding, often deteriorating the component's structural performance and reliability. In the current study, the d-spacing (inter-atomic distance) of several locations on a battery tray and stress-free reference samples are measured with neutron diffraction to calculate the residual stresses in a lap 6061 to A365 dissimilar friction-stir-weld. Furthermore, the present study connects the measured residual stress to microstructure properties through electron backscatter diffraction (EBSD) and optical microscopy analyses. The EBSD results indicate that the FSW operation affects the grains’ orientation, thereby producing location-specific directionally varying elasticity across the weldment. Further, this varied elasticity creates unique d-spacing profiles even in the stress-free material. Additionally, the resulting stressed and stress-free d-spacing profiles show dependencies on the FSW tool geometry, traverse direction, and rotational direction. Lastly, this study suggests that the final component residual stress can be influenced by the sequence of multi-pass welds contributing to a rise in temperature in the presence of a completed weld relaxing its residual stress.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Polyester-based epoxy vitrimer integrating spent coffee ground as a natural filler

Coffee is a widely consumed beverage, but approximately 80% mass of coffee cherry is discarded as waste. Here, in this study, spent coffee grounds (SCG) were recycled and used as a natural filler in a polyester-based epoxy matrix made from reactions of diglycidyl ethers of Bisphenol A and polyethylene glycol with methyl nadic anhydride. The properties of SCG/epoxy composites with various SCG contents up to 40% w/w were evaluated using various techniques such as FT-IR spectroscopy, tensile testing, optical microscopy, differential scanning calorimetry, and rheology. The SCG filled polyester-based epoxy matrix demonstrated excellent dimensional stability and retained a permanently crosslinked network, but re-shaping was possible at ~150 °C through transesterification, which occurred due to a dynamic chain exchange reaction between the ester group of the epoxy matrix and the hydroxyl group of the SCG fillers. The transesterification also improved the interfacial adhesion between the matrix and SCG fillers, resulting in tensile strength of over 20 MPa and a modulus of around 2.5 GPa, even with high SCG contents up to 40% w/w. While neat, cured epoxy shows thermoset behavior, filling the matrix with SCG enables reforming and origami-inspired spontaneous change in shape.

42 ENGINEERING↗
DOE OSTI2024

Understanding interfacial crystallization dynamics on carbon fiber reinforced polypropylene composite manufacturing

Reinforcing polymers with discontinuous fibers improves mechanical properties, such as strength and stiffness, and in some cases achieve isotropic properties, rendering them suitable for various engineering applications. Matrix materials are generally highly engineered thermosets (e.g. crosslinked epoxies), bonded to the fiber periphery by proprietary surface and sizing chemistries. Semicrystalline thermoplastic matrices are less utilized due to poor fiber-matrix bonding resulting in inefficient interfacial load-transfer in reinforced composites. However, flexibility with melt-processing or molding conditions can be leveraged to promote non-covalent interfacial bonding between matrix and fiber via crystallization of the matrix onto fiber surface. In the present study, we utilize a co-mingle chopped carbon and isotactic polypropylene fibers to form isotropic composites, tailoring interfacial immobilized matrix or interphase morphology to optimize performance through precise control of thermal processing/molding windows. Calorimetry and optical microscopy were employed to investigate the impact of carbon fiber at various volume fractions (10, 20, and 30 %) on isotactic polypropylene crystallization and mechanical performance. Variations in mechanical properties correspond to the structural evolution of the interfacial region and are correlated to underlying microstructural attributes using wide-angle X-ray scattering, thermal analysis, and low-field nuclear magnetic resonance spectroscopy. These results provide a practical framework for the manufacturing of thermoplastic matrix composites. In conclusion, the results presented provide a guide for the strategic optimization of interphase design, showcasing tailorable tensile strengths which outperform any isotactic polypropylene carbon fiber composites previously reported in literature.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Stirring and peristaltic pumping alter flow electrode particle size and morphology

Flowable carbon-based electrodes are widely studied in electrochemical systems for energy storage and water treatment. Most laboratory- and pilot-scale studies employ active mixing for slurry preparation and handling and use peristaltic pumps for slurry circulation. Magnetic stirring is the most prevalent mixing method at the laboratory scale, and the combination of magnetic mixing and peristaltic pumping is favored for convenience and compatibility with particulate suspensions. However, these methods can strongly affect particle size and morphology (and therefore cell performance). In this study, we evaluate how mixing and pumping influence particle degradation in two commonly used carbon materials: spherical carbon black (CB) beads and powdered activated carbon (AC). We performed 24 h stirring-only experiments using magnetic, orbital, and overhead stirring. Separately, we conducted 32 h circulation experiments using a commercial peristaltic pump. Particle morphology and size were analyzed using optical microscopy and laser diffraction. The initially spherical CB beads (~580 μm, 1.5 wt%) exhibit rapid and extensive breakdown under both peristaltic pumping and magnetic stirring. By comparison, AC particles (initially ~31 μm) tested at 1.5 and 15 wt% showed measurable size reductions of up to ~25 % under either stirring or pumping. In conclusion, these findings highlight the need to account for and quantify morphological changes caused by both stirring and pumping in the design and associated evaluation of flowable electrode systems.

Chemistry↗
DOE OSTI2020

Crack nucleation and growth during dynamic indentation of chemically-strengthened glass

Dynamic point impact loading is a primary cause of fracture of glass screens on mobile devices. An improved understanding of crack initiation and evolution under high-speed indentation could contribute to the development of materials with better performance, but experimental observations are challenging due to the short timescales and limited depth-of-field of optical microscopy. To address this need, we have observed fracture of a chemically-strengthened glass during dynamic indentation using in situ x-ray phase-contrast imaging (XPCI). Median cracks initiate below the surface of the glass, at a depth approximately corresponding to the depth at which the surface residual compressive stress diminishes to zero. These cracks initially propagate at ~10ms –1 , rapidly accelerating to > 100ms –1 . We also observe some evidence for rate-dependent behavior, in that indentation at the lowest rates studied here (below about ~0.15ms –1 ) fails to initiate cracks regardless of the depth of the indentation (up to 18μm), while indentation at higher rates produces median cracks that either arrest or cause complete fracture, depending on the depth of indentation.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Novel ductile wellbore cementitious composite for geologic CO 2 storage

CO 2 leakage through damaged wellbore cement sheaths is a major risk of geologic CO 2 storage (GCS), as conventional wellbore cement is brittle and can be damaged due to acid attack and downhole stresses during CO 2 injection. Here we examine a novel fiber-reinforced engineered cementitious composite (ECC) proposed as a substitute to conventional wellbore cement due to its superior ductility and intrinsic crack width control. ECC and conventional wellbore cement coupons were exposed to water in equilibrium with CO 2 at 50 °C and 10 MPa. The samples were retrieved after several days and their mechanical performance was evaluated using a four-point bending test, microhardness, and compressive strength analyses. Optical microscopy and mercury intrusion porosimetry were used to characterize the progression of the carbonation front and pore structures of the specimens. Control experiments were conducted under the same temperature and pressure conditions but with a N 2 headspace to isolate the impact of CO 2 . It was found that carbonation increased the ultimate flexural strength of ECC but decreased its ductility. However, the ductility of carbonated ECC remained higher than that of conventional wellbore cements that exhibited brittle failure under all test conditions. Additionally, ECC exhibited minimal material loss and continued resistance to deformation in comparison to conventional wellbore cements. This suggests that while the exposure of ECC to CO 2 will alter its mechanical properties, altered ECC will continue to exhibit mechanical performance superior to conventional wellbore cement, and therefore shows promise as a highly durable wellbore cementing material for GCS applications.

58 GEOSCIENCES↗
DOE OSTI2022

Catalyst layer formulations for slot-die coating of PEM fuel cell electrodes

The series of electrodes were fabricated by the scalable and manufacturable slot-die coating method for proton exchange membrane fuel cell (PEMFC) application. The inks with different amounts of solids were studied by rheological methods in order to establish a coating window with minimum manufacturing defects. The obtained electrodes were characterized by SEM, AFM, and optical microscopy, which showed that they were uniform and homogeneous with minimum defects. The electrochemical evaluation of the manufactured gas diffusion electrodes (GDE) showed that the main characteristics of the electrodes, like electrochemical surface area, proton resistivity, and double layer capacitance, were found to be close for all samples confirming the reproducibility of the slot-die process. Additionally, we studied the effects of membrane thickness on the performance of the GDE membrane electrode assemblies and determined that a decrease in membrane thickness favored the performance. Furthermore, the obtained results clearly demonstrated the applicability and feasibility of the approach for the Manufacturing of catalyst layers for the fuel cell application with potential for future mass production.

08 HYDROGEN↗
DOE OSTI2025

Linking structure to performance: Characterization of porous transport layers for high-pressure water electrolysis

Proton exchange membrane (PEM) water electrolysis is a promising technology to produce cost-efficient hydrogen. PEM electrolyzers offer a large current density range and the ability to operate at differential pressure which can be used to minimize both capital and operational expenditures. However, directly producing pressurized hydrogen at the cathode results in pushing the membrane against the anode porous transport layer (PTL). This can lead to detrimental effects, such as membrane deformation or ruptures, which depend on membrane properties as well as PTL material properties such as pore size, structure, and morphology. In this work, a range of sinter and felt-based commercial PTLs are evaluated for their contributions to the cell's electrochemical and H 2 crossover performance at cathode pressures up to 30 bar. X-ray tomography and post-operando optical microscopy are used to assess the morphology of the PTLs, and the PTL induced deformation experienced by the catalyst coated membrane (CCM), respectively. PTL samples with lower porosity were found to reduce both the cell voltage and the amount of H 2 permeating from the cathode to the anode exhaust, which was ascribed to improved catalyst layer contact and reduced membrane deformation, respectively. The best performing PTLs improved electrolyzer efficiency by ~1.5 kWh/kg H2 . Specifically, 1 kWh/kg H2 was gained due to reducing membrane deformation and decreasing H 2 crossover. The remainder 0.5 kWh/kg H2 were achieved by improving the electrical contact at the electrode/PTL interface which decreased cell voltage.

08 HYDROGEN↗