Search NASA⌕ Search

SEARCH · Search NASA

Results for “phase transformations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Phase transformation in tantalum under extreme laser deformation

The structural and mechanical response of metals is intimately connected to phase transformations. For instance, the product of a phase transformation (martensite) is responsible for the extraordinary range of strength and toughness of steel, making it a versatile and important structural material. Although abundant in metals and alloys, the discovery of new phase transformations is not currently a common event and often requires a mix of experimentation, predictive computations, and luck. High-energy pulsed lasers enable the exploration of extreme pressures and temperatures, where such discoveries may lie. The formation of a hexagonal (omega) phase was observed in recovered monocrystalline body-centered cubic tantalum of four crystallographic orientations subjected to an extreme regime of pressure, temperature, and strain-rate. This was accomplished using high-energy pulsed lasers. The omega phase and twinning were identified by transmission electron microscopy at 70 GPa (determined by a corresponding VISAR experiment). It is proposed that the shear stresses generated by the uniaxial strain state of shock compression play an essential role in the transformation. In conclusion, molecular dynamics simulations show the transformation of small nodules from body-centered cubic to a hexagonal close-packed structure under the same stress state (pressure and shear).

36 MATERIALS SCIENCE↗

Phase-field modeling of the beta to omega phase transformation in Zr–Nb alloys

A three-dimensional elastoplastic phase-field model is developed, using the Finite Element Method (FEM), for modeling the athermal beta to omega phase transformation in Zr–Nb alloys by including plastic deformation and strain hardening of the material. The microstructure evolution during athermal transformation as well as under different stress states, e.g. uni-axial tensile and compressive, bi-axial tensile and compressive, shear and tri-axial loadings, is studied. The effects of plasticity, stress states and the stress loading direction on the microstructure evolution as well as on the mechanical properties are studied. The input data corresponding to a Zr – 8 at.% Nb alloy are acquired from experimental studies as well as by using the CALPHAD method. Our simulations show that the four different omega variants grow as ellipsoidal shaped particles. Our results show that due to stress relaxation, the athermal phase transformation occurs slightly more readily in the presence of plasticity compared to that in its absence. The evolution of omega phase is different under different stress states, which leads to the differences in the mechanical properties of the material. The variant selection mechanism, i.e. formation of different variants under different stress loading directions, is also nicely captured by our model.

36 MATERIALS SCIENCE↗

Nanosecond in situ transmission electron microscope studies of the reversible Ge{sub 2}Sb{sub 2}Te{sub 5} crystalline <==> amorphous phase transformation

Chalcogenide-based phase-change materials have wide use in optical recording media and are growing in importance for use in non-volatile electronic memory. For both applications, rapid switching between the amorphous and crystalline phases is necessary, and understanding the changes during rapidly driven phase transitions is of scientific and technological significance. Laser-induced crystallization and amorphization occur rapidly and changes in atomic structure, microstructure, and temperature are difficult to observe experimentally and determine computationally. We have used nanosecond-scale time-resolved diffraction with intense electron pulses to study Ge{sub 2}Sb{sub 2}Te{sub 5} during laser crystallization. Using a unique and unconventional specimen geometry, cycling between the amorphous and crystalline phases was achieved, enabling in situ transmission electron microscope (TEM) study of both microstructural and crystallographic changes caused by repeated switching. Finite element analysis was used to simulate interactions of the laser with the nano-structured specimens and to model the rapidly changing specimen temperature. Such time-resolved experimental methods combined with simulation of experimentally inaccessible physical characteristics will be fundamental to advancing the understanding of rapidly driven phase transformations.

36 MATERIALS SCIENCE↗

Problem of Identification of Phase Transformation Models Used in Simulations of Steels Processing

Accuracy of phase transformation models depends on the correctness of coefficients evaluation, adequate to the investigated material. Dilatometric tests combined with the inverse analysis are used to perform identification. Since the problem is nonlinear, analytical approach is not possible and the inverse solution is transferred into the optimization task. It leads to difficulties typical for optimization of multivariable function such as local minima and lack of proof of the uniqueness. The problem of the effectiveness and uniqueness of the inverse algorithms used for identification of phase transformation models for steels was investigated for two models. The first was a modified JMAK (Johnson–Mehl–Avrami–Kolmogorov) equation. The second was an upgrade of the Leblond equation, in which second-order derivative of the volume fraction with respect to time was introduced. In classical identification, the result for one transformation depends on the coefficients for the remaining transformations and optimization has to be performed several times until the compatibility between transformations is reached. To avoid encountered problems, complex optimization simultaneously for all coefficients in the models was performed. This approach was based on nature-inspired optimization techniques. Models with identified coefficients for various steels were validated in simulations of industrial processes of laminar cooling and continuous annealing of strips.

36 MATERIALS SCIENCE↗

Subsurface characterization of an oxidation-induced phase transformation and twinning in nickel-based superalloy exposed to oxy-combustion environments

In the integration of oxy-fuel combustion to turbine power generation system, turbine alloys are exposed to high temperature and an atmosphere comprised of steam, CO{sub 2} and O{sub 2}. While surface and internal oxidation of the alloy takes place, the microstructure in the subsurface region also changes due to oxidation. In this study, bare metal coupons of Ni-base superalloys were exposed in oxy-fuel combustion environment for up to 1000 h and the oxidation-related microstructures were examined. Phase transformation occurred in the subsurface region in Ni-based superalloy and led to twinning. The transformation product phases were analyzed through thermodynamic equilibrium calculations and various electron microscopy techniques, including scanning electron microscopy (SEM), orientation imaging microscopy (OIM) and transmission electron microscopy (TEM). The mechanism by which the phase transformation and the formation of the microstructure occurred was also discussed. The possible effects of the product phases on the performance of the alloy in service were discussed.

High temperature oxidation↗

Pulse current auxiliary forging of sintered TiAl alloys based on the investigation of dynamic recrystallization and phase transformation

Highlights: • DRX kinetics model of sintered near γ TiAl alloy was established. • DRX process was accompanied by twinning when compressed at 1125 °C/0.1 s{sup − 1}. • Hot deformation has a promotion to the phase transformation of γ → α. - Abstract: Pulse current auxiliary forging is a new and efficient way to fabricate high performance TiAl based alloys. Dynamic recrystallization (DRX) and phase transformation have a pronounced effect on the subsequent deformability of TiAl based alloys. Hence, the dynamic recrystallization kinetics were determined at the temperature range of 1125–1275 °C and strain rate range of 0.1–0.001 s{sup − 1}. In addition, the DRX mechanism and phase transformation of TiAl based alloys were investigated to model the microstructure evolution in order to provide guidance for the pulse current auxiliary forging process. When the specimens were compressed at 1125 °C/0.1 s{sup − 1}, twinning played an important role in the DRX process. With increasing deformation temperature, the microstructure transformed from near gamma into duplex microstructure. In addition, according to the kinetics of dynamic recrystallization and phase transformation, fully DRXed TiAl based alloys were fabricated through pulse current auxiliary forging. The as-forged TiAl-based alloys show good superplastic performance with an elongation over 410%.

36 MATERIALS SCIENCE↗

Lattice distortion-induced phase transformations in La{sub 1-y}Pr{sub y}MnO{sub 3+{delta}} manganites

The structural and magnetic phase transformations that occur in the system of self-doped La{sub 1-y}Pr{sub y}MnO{sub 3+{delta}} ({delta} Almost-Equal-To 0.1, 0 {<=} y {<=} 1) manganites in the temperature range 4.2-300 K are studied by X-ray diffraction and measuring the temperature and field dependences of dc magnetization. The low-temperature magnetic phase transformations induced by the substitution of Pr for La correlate well with the structural phase transformations at T = 300 K, which indicates a strong coupling of the electronic and magnetic subsystems of La{sub 1-y}Pr{sub y}MnO{sub 3+{delta}} manganites with the crystal lattice. The anomalies of the magnetic and structural properties detected in this work in the form of peaks and inflection points in the concentration dependences of the magnetization and lattice parameters of the pseudocubic phase of La{sub 1-y}Pr{sub y}MnO{sub 3+{delta}} (0.1 {<=} y {<=} 0.7) in the temperature range 4.2-300 K are explained in terms of the existing concepts of the effect of Fermi surface nesting on the renormalization of the density of states and the hole dispersion near E{sub F} in the presence of a strong coupling of holes with low-frequency optical phonons, which results in their transformation into quasiparticles. The narrow peak in the magnetization curve M(y) of La{sub 1-y}Pr{sub y}MnO{sub 3+{delta}} that is detected near y = 0.3 at T = 4.2 K is assumed to correspond to the peak of coherence of quasiparticles with a low energy of coupling with the crystal lattice near E{sub F}, which was found earlier in the photoelectron emission spectra of manganites. The disappearance of the narrow magnetization peak with increasing Pr concentration is explained by the transition of charge carriers from the mode of 'light' holes weakly coupled to one of the soft phonons to the mode of 'heavy' holes strongly coupled to several phonons. The transition between phases with strongly different effective quasiparticle masses proceeds jumpwise; that is, it has features of the metal-insulator Mott transition and is accompanied by the transition from 3D to 2D quasiparticle motion in planes ab.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Recordings and Analysis of Atomic Ledge and Dislocation Movements in InGaAs to Nickelide Nanowire Phase Transformation

The formation of low resistance and self‐aligned contacts with thermally stable alloyed phases is a prerequisite for realizing reliable functionality in ultrascaled semiconductor transistors. Detailed structural analysis of the phase transformation accompanying contact alloying can facilitate contact engineering as transistor channels approach a few atoms across. Original in situ heating transmission electron microscopy studies are carried out to record and analyze the atomic scale dynamics of contact alloy formation between Ni and In 0.53 Ga 0.47 As nanowire channels. It is observed that the nickelide reacts on the In 0.53 Ga 0.47 As (111) || Ni 2 In 0.53 Ga 0.47 As (0001) interface with atomic ledge propagation along the Ni 2 In 0.53 Ga 0.47 As direction. Ledges nucleate as a train of strained single‐bilayers and propagate in‐plane as double‐bilayers that are associated with a misfit dislocation of . The atomic structure is reconstructed to explain this phase transformation that involves collective gliding of three Shockley partials in In 0.53 Ga 0.47 As lattice to cancel out shear stress and the formation of misfit dislocations to compensate the large lattice mismatch in the newly formed nickelide phase and the In 0.53 Ga 0.47 As layers. This work demonstrates the applicability of interfacial disconnection (ledge + dislocation) theory in a nanowire channel during thermally induced phase transformation that is typical in metal/III–V semiconductor reactions.

Chen, Renjie↗

Hydrogen dynamics and characterization of the tetragonal-to-orthorhombic phase transformation in ammonia borane

The anelastic spectrum of ammonia borane (NH3BH3) was measured in the temperature range between 1.3 and 300 K. The structural phase transition near 220 K is accompanied by a substantial variation of the elastic modulus (25-30 %) and a spike of the elastic energy dissipation. The order-disorder phase transformation which occurs with a minute hysteresis, 0.4 K between heating and cooling is indicative of a first order phase transformations with a narrow region of coexistence between the two phases. The kinetics of the transition was investigated in detail. In addition, a thermally activated relaxation peak is revealed around 100 K for a sample vibration frequency of ~ 1 kHz, which is attributed to the dynamics of the rotations and torsions of the NH3-BH3 groups. Finally, the time-dependent energy loss on heating after ageing the sample below the structural phase transformation temperature was interpreted in terms of annealing of dislocations

08 HYDROGEN↗

Phase Transformations Driving Biaxial Stress Reduction During Wake-Up of Ferroelectric Hafnium Zirconium Oxide Thin Films

Biaxial stress is identified to play an important role in the polar orthorhombic phase stability in hafnium oxide-based ferroelectric thin films. However, the stress state during various stages of wake-up has not yet been quantified. In this work, the stress evolution with field cycling in hafnium zirconium oxide capacitors is evaluated. The remanent polarization of a 20 nm thick hafnium zirconium oxide thin film increases from 9.80 to 15.0 µC cm –2 following 10 6 field cycles. This increase in remanent polarization is accompanied by a decrease in relative permittivity that indicates that a phase transformation has occurred. The presence of a phase transformation is supported by nano-Fourier transform infrared spectroscopy measurements and scanning transmission electron microscopy that show an increase in ferroelectric phase content following wake-up. The stress of individual devices field cycled between pristine and 10 6 cycles is quantified using the sin 2 (ψ) technique, and the biaxial stress is observed to decrease from 4.3 ± 0.2 to 3.2 ± 0.3 GPa. The decrease in stress is attributed, in part, to a phase transformation from the antipolar Pbca phase to the ferroelectric Pca2 1 phase. This work provides new insight into the mechanisms controlling and/or accompanying polarization wake-up in hafnium oxide-based ferroelectrics.

36 MATERIALS SCIENCE↗

Operando real-space imaging of a structural phase transformation in the high-voltage electrode LixNi0.5Mn1.5O4

Abstract Discontinuous solid-solid phase transformations play a pivotal role in determining the properties of rechargeable battery electrodes. By leveraging operando Bragg Coherent Diffractive Imaging (BCDI), we investigate the discontinuous phase transformation in Li x Ni 0.5 Mn 1.5 O 4 within an operational Li metal coin cell. Throughout Li-intercalation, we directly observe the nucleation and growth of the Li-rich phase within the initially charged Li-poor phase in a 500 nm particle. Supported by the microelasticity model, the operando imaging unveils an evolution from a curved coherent to a planar semi-coherent interface driven by dislocation dynamics. Our data indicates negligible kinetic limitations from interface propagation impacting the transformation kinetics, even at a discharge rate of C/2 (80 mA/g). This study highlights BCDI’s capability to decode complex operando diffraction data, offering exciting opportunities to study nanoscale phase transformations with various stimuli.

Sun, Yifei (ORCID:0000000295625120)↗

A comparison of dilatometry and in-situ neutron diffraction in tracking bulk phase transformations in a martensitic stainless steel

Phase transformations in the 17-4PH martensitic stainless steel have been studied using different in-situ techniques, including dilatometry and high resolution neutron diffraction. Neutron diffraction patterns were quantitatively processed using the Rietveld refinement method, allowing the determination of the temperature-dependence of martensite (α′, bcc) and austenite (γ, fcc) phase fractions and lattice parameters on heating to 1000 °C and then cooling to room temperature. It is demonstrated in this work that dilatometry doesn't permit an accurate determination of the end temperature (Ac3) of the α′ → γ transformation which occurs upon heating to high temperature. The analysis of neutron diffraction data has shown that the respective volumes of the two phases become very close to each other at high temperature, thus making the dilatometric technique almost insensitive in that temperature range. However, there is a very good agreement between neutron diffraction and dilatometry at lower temperature. The martensitic transformation occurring upon cooling has been analysed using the Koistinen–Marburger equation. The thermal expansion coefficients of the two phases have been determined in addition. A comparison of the results obtained in this work with data from literature is presented. - Highlights: • Martensite is still present at very high temperature (> 930 °C) upon heating. • The end of austenitisation cannot be accurately monitored by dilatometry. • The martensite and austenite volumes become similar at high temperature (> ∼ 850 °C)

36 MATERIALS SCIENCE↗

Phase transformations in a Cu−Cr alloy induced by high pressure torsion

Phase transformations induced by high pressure torsion (HPT) at room temperature in two samples of the Cu-0.86 at.% Cr alloy, pre-annealed at 550 °C and 1000 °C, were studied in order to obtain two different initial states for the HPT procedure. Observation of microstructure of the samples before HPT revealed that the sample annealed at 550 °C contained two types of Cr precipitates in the Cu matrix: large particles (size about 500 nm) and small ones (size about 70 nm). The sample annealed at 1000 °C showed only a little fraction of Cr precipitates (size about 2 μm). The subsequent HPT process resulted in the partial dissolution of Cr precipitates in the first sample and dissolution of Cr precipitates with simultaneous decomposition of the supersaturated solid solution in another. However, the resulting microstructure of the samples after HPT was very similar from the standpoint of grain size, phase composition, texture analysis and hardness measurements. - Highlights: • Cu−Cr alloy with two different initial states was deformed by HPT. • Phase transformations in the deformed materials were studied. • SEM, TEM and X-ray diffraction techniques were used for microstructure analysis. • HPT leads to formation the same microstructure independent of the initial state.

36 MATERIALS SCIENCE↗

Mechanochemical spinodal decomposition: a phenomenological theory of phase transformations in multi-component, crystalline solids

Here, we present a phenomenological treatment of diffusion-driven martensitic phase transformations in multi-component crystalline solids that arise from non-convex free energies in mechanical and chemical variables. The treatment describes diffusional phase transformations that are accompanied by symmetry-breaking structural changes of the crystal unit cell and reveals the importance of a mechanochemical spinodal, defined as the region in strain-composition space, where the free-energy density function is non-convex. The approach is relevant to phase transformations wherein the structural order parameters can be expressed as linear combinations of strains relative to a high-symmetry reference crystal. The governing equations describing mechanochemical spinodal decomposition are variationally derived from a free-energy density function that accounts for interfacial energy via gradients of the rapidly varying strain and composition fields. A robust computational framework for treating the coupled, higher-order diffusion and nonlinear strain gradient elasticity problems is presented. Because the local strains in an inhomogeneous, transforming microstructure can be finite, the elasticity problem must account for geometric nonlinearity. An evaluation of available experimental phase diagrams and first-principles free energies suggests that mechanochemical spinodal decomposition should occur in metal hydrides such as ZrH 2-2c . The rich physics that ensues is explored in several numerical examples in two and three dimensions, and the relevance of the mechanism is discussed in the context of important electrode materials for Li-ion batteries and high-temperature ceramics.

36 MATERIALS SCIENCE↗

Effect of Plane Strain Compression and Subsequent Recrystallization Annealing on Microstructures and Phase Transformation of NiTiFe Shape Memory Alloy

The effect of plane strain compression and subsequent recrystallization annealing on microstructures and phase transformation of NiTiFe shape memory alloy (SMA) is investigated. Inhomogeneous plastic deformation at various deformation degrees occurs in NiTiFe SMA during plane strain compression. Nanocrystalline phase and amorphous phase increase as the deformation degree increases. B2 austenite, B19′ martensite, nanocrystalline and amorphous phases coexist in the NiTiFe samples subjected to large plastic strain. The static recrystallization mechanisms depend on the microstructures of the deformed NiTiFe samples. The static recrystallization mechanisms deal with nucleation and growth of the recrystallized grains, growth of nanocrystalline phase and crystallization of amorphous phase. Grain size, subgrain boundaries, geometrically necessary dislocation density and Schmid factor are captured on the basis of electron backscattered diffraction data. The process of recrystallization annealing cannot eliminate the deformation texture completely. The slip direction [110] is the most favorable slip direction in the recrystallized NiTiFe sample. Plane strain compression along with subsequent recrystallization annealing changes the phase transformation path of as-rolled NiTiFe SMA, and it results in the decreasing martensite transformation start temperature. The three annealed NiTiFe samples exhibit the similar phase transformation behavior since complete recrystallization annealing leads to the similar microstructures.

36 MATERIALS SCIENCE↗

Numerical estimation of phase transformations in solid state during Yb:YAG laser heating of steel sheets

This work concerns the numerical modeling of heat transfer and phase transformations in solid state occurring during the Yb:YAG laser beam heating process. The temperature field is obtained by the numerical solution into transient heat transfer equation with convective term. The laser beam heat source model is developed using the Kriging interpolation method with experimental measurements of Yb:YAG laser beam profile taken into account. Phase transformations are calculated on the basis of Johnson - Mehl - Avrami (JMA) and Koistinen - Marburger (KM) kinetics models as well as continuous heating transformation (CHT) and continuous cooling transformation (CCT) diagrams for S355 steel. On the basis of developed numerical algorithms 3D computer simulations are performed in order to predict temperature history and phase transformations in Yb:YAG laser heating process.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Orientation relationships of phase transformation in α-Al12Mn3Si pseudomorphs after plate-like Al6Mn precipitate in an AA3004 Al-Mn based alloy

Highlights: • The phase transformation in the plate-like precipitates was investigated by TEM. • The shape of a plate-like Al{sub 6}Mn was kept after transforming to the α-Al{sub 12}Mn{sub 3}Si. • Pseudomorph in metal materials has been found out. - Abstract: The phase transformation in the plate-like precipitates of Al{sub 6}Mn in an AA3004 Al-Mn based alloy, which was prepared by a chemical extraction technique, was investigated using transmission electron microscopy. The boiling-phenol method observed the entire range of possible shapes of the precipitates and the habit planes of the plate-like Al{sub 6}Mn were <001> in the sheet plane and <110> on its edges. The two orientation relationships between Al{sub 6}Mn and α-Al{sub 12}Mn{sub 3}Si after the phase transformation is observed to be [00 1-bar ]{sub 6}//[02 3-bar ]{sub α} and (130){sub 6}//(5 3-bar 2){sub α} and [00 1-bar ]{sub 6}//[1 5-bar 2]{sub α} and (200){sub 6}//(311){sub α} (particles 1 and 2) (the suffixes 6 and α indicate zone axises or lattice planes of Al{sub 6}Mn and α-Al{sub 12}Mn{sub 3}Si phases, respectively). The lattice misfits in these orientation relationships were observed to be − 1.4% and 1.0%, respectively. Additionally, the thickness of the plate-like Al{sub 6}Mn was kept constant after transforming into the α-Al{sub 12}Mn{sub 3}Si phase. Further, we did not observe any low index planes of the α-Al{sub 12}Mn{sub 3}Si parallel to the (001) plane of the Al{sub 6}Mn, which means that the outlines of α-Al{sub 12}Mn{sub 3}Si were constrained by the original shape of Al{sub 6}Mn, i.e., the transformed α-Al{sub 12}Mn{sub 3}Si may be considered as a pseudomorph after Al{sub 6}Mn.

36 MATERIALS SCIENCE↗

Phase Transformation and Particle-Mediated Growth in the Formation of Hematite from 2-Line Ferrihydrite

Iron oxide nanoparticles are present throughout the Earth and undergo mineral phase transformations that affect their stability and reactivity. The formation of the iron oxide hematite from a 2-line ferrihydrite (2lnFh) precursor requires both phase transformation and growth. Whether phase transformation occurs before or after substantial particle growth, and by which mechanisms particles grow, remain unclear. We conducted time-resolved studies employing X-ray diffraction, room temperature and cryogenic transmission electron microscopy, preferential dissolution by oxalate buffer, and low temperature SQuID magnetometry to investigate the kinetics and mechanism of hematite formation from 2lnFh. A novel form of magnetic measurement was found to be exquisitely sensitive to the presence of hematite, detecting its formation at far lower concentrations than possible with X-ray diffraction. These results indicate that small hematite domains were present even in as-prepared 2lnFh suspensions as a side-product of 2lnFh synthesis and that the hematite domains increased in size and crystallinity with aging time at elevated temperatures. In conclusion, second-order kinetics reveals that the hematite growth is consistent with a particle-mediated growth mechanism, possibly oriented attachment.

36 MATERIALS SCIENCE↗