Search NASA⌕ Search

SEARCH · Search NASA

Results for “pitching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Target pitch angle for the microburst escape maneuver

The objective of this study was to investigate the constant pitch attitude strategy as a possible non-precision maneuver for recovery from inadvertent wind shear encounters. The Wind Shear Training Aid published by the FAA recommends that upon encountering a severe wind shear, the pilot should apply maximum thrust and rotate the aircraft to an initial pitch target angle of 15 degrees. The 15 degrees target was identified through rigorous analyses using six-degree-of-freedom flight simulators and microburst models representative of actual accident cases. It was found that 15 degrees was an effective target for a wide range of shears, and was generally applicable to most jet transports. This work was undertaken to examine the issue of recovery performance in wind shear of other classes of aircraft - notably turboprop commuters and propeller-driven general aviation planes. It should be possible to postulate a target pitch angle (TPA) for such aircraft, as well.

Mulgund, Sandeep S.↗

Physics of pitch angle scattering and velocity diffusion. I - Theory

A general theory for the pitch angle scattering and velocity diffusion of particles in the field of a spectrum of waves in a magnetized plasma is presented. The test particle theory is used to analyze the particle motion. The form of diffusion surfaces is examined, and analytical expressions are given for the resonance width and bounce frequency. The resonance widths are found to vary strongly as a function of harmonic number. The resulting diffusion can be quite asymmetric with respect to pitch angle of 90 deg. The conditions for the onset of pitch angle scattering and energy diffusion are explained in detail. Some of the known shortcomings of the standard quasi-linear theory are also addressed, and ways to overcome them are shown. In particular, the often stated quasi-linear gap at 90 deg is found to exist only under very special cases. For instance, oblique wave propagation can easily remove the gap. The conditions for the existence of the gap are described in great detail. A new diffusion equation which takes into account the finite resonance widths is also discussed. The differences between this new theory and the standard resonance broadening theory is explained.

Karimabadi, H.↗

Unsteady transition measurements on a pitching three-dimensional wing

Boundary layer transition measurements were made during an experimental study of the aerodynamics of a rectangular wing undergoing unsteady pitching motions. The wing was tested at chordwise Mach numbers between 0.2 and 0.6, at sweep angles of 0, 15, and 30 deg, and for steady state, sinusoidal, and constant pitch rate motions. The model was scaled to represent a full size helicopter rotor blade, with chord Reynolds numbers between 2 and 6 x 10(exp 6). Sixteen surface hot-film gages were located along three spanwise stations: 0.08, 0.27, and 0.70 chords from the wing tip. Qualitative heat transfer information was obtained to identify the unsteady motion of the point of transition to turbulence. In combination with simultaneous measurements of the unsteady surface pressure distributions, the results illustrate the effects of compressibility, sweep, pitch rate, and proximity to the wing tip on the transition and relaminarization locations.

Lorber, Peter F.↗

On the distribution of pitch angles in external galactic spirals NGC 1232 and NGC 5457

A numerical method, originally developed to analyze the morphology of global and local structure in prototype galaxies, is modified for analyzing observed disk-shape galaxies. Two digitized spiral galaxies NGC 1232 and NGC 5457 with varying degrees of contrast between arm and interarm regions are analyzed. A synergism of partitioning methods and a geometric mean least-squares regression algorithm serves to isolate local arm segments, spurs, feathers, and secondary features and to measure their pitch angles and lengths. The global arms are actually highly disjointed, with arm segments frequently revealing pitch angles between 30 and 50 deg, certainly greater than those of the parent arms. Prominent spurs tend to exhibit a much greater pitch angle. The automated mathematical algorithm is shown to have negligible numerical biasing and could be applied to any number of spiral galaxies manifesting flocculent structure, either prototype or observed, and could possibly be used as a tool for classification of multiple-armed-type galaxies.

Russell, William S.↗

Test of an adjustable pitch model propeller at four blade settings

This note describes tests of an adjustable blade metal model propeller, both in a free wind stream and in combination with a model fuselage, at four settings of the blades. The model propeller is designed for a uniform nominal pitch/diameter ratio of .7 and the blade settings used correspond to nominal pitch/diameter ratios of .5, .7, .9, and 1.1 at the .6 radius. The tests show that propellers of this type may be considerably changed in setting from the designed pitch angles and yet give excellent performance. The efficiency realized and power absorbed when blades are set at other than the designed angle, are little different than would be obtained from a propeller with uniform pitch equal to the mean pitch of the propeller under test.

Lesley, E P↗

A study of the pitching moments and the stability characteristics of monoplanes

This note presents a study of the pitching moments and the stability characteristics of monoplanes. Expressions for the pitching-moment coefficient and the Diehl stability coefficient for the monoplane are developed, suitable for the use of airplane designers. The effective difference between the high-wing and low-wing types is portrayed and discussed. Comparisons between experimental and computed values are made. Charts for use in the solution of numerical values of the pitching-moment and stability coefficients are presented.

Higgins, George J↗

Charts for determining the pitching moment of tapered wings with sweepback and twist

This report presents a convenient method for calculating the pitching-moment characteristics of tapered wings with sweepback and twist. The method is based on the fact that the pitching-moment characteristics of a wing may be specified by giving the value of the pitching moment at zero lift and the location of the axis about which the axis is constant. Data for calculating these characteristics are presented by curves which apply to wings having a linear distribution of twist along the span and which cover a large range of aspect ratios. The curves are given for wings having straight taper and distorted elliptical plan forms. The characteristics of wings of other shapes may be determined by interpolation.

Anderson, Raymond F↗

Effect of Rivet Pitch upon the Fatigue Strength of Single-row Riveted Joints of 0.025- to 0.025-inch 24S-T Alclad

S-N curves at the range ratio of 0.2 were experimentally obtained for each of the following values of rivet pitch P as used in a single-row lap joint of 0.025- to 0.025-inch 24S-T alclad with one-eight AN430 round-head rivets: p=0.5, 0.75, 1.0, 1.5. Families of constant rivet pitch curves, which define the fatigue life for specimens studied, were developed. Curves showing the variation of the effective stress concentration factor in fatigue with rivet pitch and maximum load per rivet were also established.

Seliger, Victor↗

Measurement of Aerodynamic Forces for Various Mean Angles of Attack on an Airfoil Oscillating in Pitch and on Two Finite-span Wings Oscillating in Bending with Emphasis on Damping in the Stall

The oscillating air forces on a two-dimensional wing oscillating in pitch about the midchord have been measured at various mean angles of attack and at Mach numbers of 0.35 and 0.7. The magnitudes of normal-force and pitching-moment coefficients were much higher at high angles of attack than at low angles of attack for some conditions. Large regions of negative damping in pitch were found, and it was shown that the effect of increasing the Mach number 0.35 to 0.7 was to decrease the initial angle of attack at which negative damping occurred. Measurements of the aerodynamic damping of a 10-percent-thick and of a 3-percent-thick finite-span wing oscillating in the first bending mode indicate no regions of negative damping for this type of motion over the range of variables covered. The damping measured at high angles of attack was generally larger than that at low angles of attack. (author)

Rainey, A Gerald↗

Tests of a Wing-nacelle-Propeller Combination at Several Pitch Settings up to 42 Degrees

This report presents the results of tests of a 4-foot model of Navy propeller No. 4412 in conjunction with an NACA cowled nacelle mounted ahead of a thick wing in the 20-foot propeller-research tunnel. A range of propeller pitches from 17 degrees to 42 degrees at 0.75r was covered, and for this propeller the efficiency reached a maximum at a pitch setting of 27 degrees; at high pitches the efficiencies were slightly lower. The corrected propulsive efficiency is shown to be independent of the angle of attack for the high-speed and the climbing ranges of flight. A working chart is presented for the selection of similar propellers over a wide range of airplane speed, engine power, and propeller revolution.

Windler, Ray↗

Low-speed pitching derivatives of low-aspect-ratio wings of triangular and modified triangular plan forms

A low-speed investigation was made in the 6- by 6-foot curved-flow test section of the Langley stability tunnel to determine the effects of change in profile and aspect ratio on the pitching derivatives of triangular wings. The effects of aspect ratio on the pitching derivatives of a series of modified triangular wings, obtained by cutting various portions from the tips of a basic triangle, also were determined. Values of the damping-in-pitch parameter (Cmq) obtained for the triangular and modified triangular wings were one-fifth to one-tenth as large as the value expected for a typical airplane.

Goodman, Alex↗

A determination of the external forces required to move the benchmark active controls testing model in pure plunge and pure pitch

In view of the strong need for a well-documented set of experimental data which is suitable for the validation and/or calibration of modern Computational Fluid Dynamics codes, the Benchmark Models Program was initiated by the Structural Dynamics Division of the NASA Langley Research Center. One of the models in the program, the Benchmark Active Controls Testing Model, consists of a rigid wing of rectangular planform with a NACA 0012 profile and three control surfaces (a trailing-edge control surface, a lower-surface spoiler, and an upper-surface spoiler). The model is affixed to a flexible mount system which allows only plunging and/or pitching motion. An approximate analytical determination of the forces required to move this model, with its control surfaces fixed, in pure plunge and pure pitch at a number of test conditions is included. This provides a good indication of the type of actuator system required to generate the aerodynamic data resulting from pure plunging and pure pitching motion, in which much interest was expressed. The analysis makes use of previously obtained numerical results.

Dcruz, Jonathan↗

Interferometric investigations of compressible dynamic stall over a transiently pitching airfoil

The dynamic stall flow field over NACA 0012 airfoil pitching transiently from 0 - 60 at a constant rate under compressible flow conditions has been studied using the real-time technique of point diffraction interferometry. This investigation using nonintrusive diagnostics provides a quantitative description of the overall flow field, including the finer details of dynamic stall vortex formation, growth and the concomitant changes in the pressure distribution. Analysis of several hundred interferograms obtained for a range of flow conditions shows that the peak leading edge suction pressure coefficient that stall is nearly constant for a given free stream Mach number at all nondimensional pitch rates. Also, this value is below that seen in steady flow at static stall for the same Mach number, indicating that dynamic effects significantly effect the separation behavior. Further, for a given Mach number, the dynamic stall vortex seems to form rapidly at nearly the same angle of attack for all pitch rates studied. As the vortex is shed, it induces an anti-clockwise trailing edge vortex, which grows in a manner similar to that of a starting vortex. The measured peak suction pressure coefficient drops as the free stream Mach number increases. For free stream Mach numbers above 0.4, small multiple shocks appear near the leading edge.

Chandrasekhara, M. S.↗

Unsteady flow past an airfoil pitched at constant rate

The unsteady flow past a NACA 0012 airfoil that is undertaking a constant-rate pitching up motion is investigated experimentally by the PIDV technique in a water towing tank. The Reynolds number is 5000, based upon the airfoil's chord and the free-stream velocity. The airfoil is pitching impulsively from 0 to 30 deg. with a dimensionless pitch rate alpha of 0.131. Instantaneous velocity and associated vorticity data have been acquired over the entire flow field. The primary vortex dominates the flow behavior after it separates from the leading edge of the airfoil. Complete stall emerges after this vortex detaches from the airfoil and triggers the shedding of a counter-rotating vortex near the trailing edge. A parallel computational study using the discrete vortex, random walk approximation has also been conducted. In general, the computational results agree very well with the experiment.

Lourenco, L.↗

Delta wing vortex manipulation using pulsed and steady blowing during ramp pitching

The effectiveness of steady and pulsed blowing as a method of controlling delta wing vortices during ramp pitching has been investigated in flow visualization experiments conducted in a water tunnel. The recessed angled spanwise blowing technique was utilized for vortex manipulation. This technique was implemented on a beveled 60 delta wing using a pair of blowing ports located beneath the vortex core at 40% chord. The flow was injected primarily in the spanwise direction but was also composed of a component normal to the wing surface. The location of vortex burst was measured as a function of blowing intensity and pulsing frequency under static conditions, and the optimum blowing case was applied at three different wing pitching rates. Experimental results have shown that, when the burst location is upstream of the blowing port, pulsed blowing delays vortex breakdown in static and dynamic cases. Dynamic tests verified the existence of a hysteresis effect and demonstrated the improvements offered by pulsed blowing over both steady blowing and no-blowing scenarios. The application of blowing, at the optimum pulsing frequency, made the vortex breakdown location comparable in static and ramp pitch-up conditions.

Moreira, J.↗

Status of the Validation of High-Angle-Of-Attack Nose-Down Pitch Control Margin Design Guidelines

This paper presents a summary of results obtained to date in an ongoing cooperative research program between NASA and the U.S. Navy to develop design criteria for high-angle-of-attack nose- down pitch control for combat aircraft. A fundamental design consideration for aircraft incorporating relaxed static stability in pitch is the level of stability which achieves a proper balance between high- speed performance considerations and low-speed requirements for maneuvering at high angles of attack. A comprehensive data base of piloted simulation results was generated for parametric variations of critical parameters affecting nose-down control capability. The results showed a strong correlation of pilot rating to the short-term pitch response for nose-down commands applied at high- angle-of-attack conditions. Using these data, candidate design guidelines and flight demonstration requirements were defined. Full- scale flight testing to validate the research methodology and proposed guidelines is in progress, some preliminary results of which are reviewed.

Ogburn, Marilyn E.↗

Effects of body orientation and rotation axis on pitch visual-vestibular interaction

Spatial transformations of the vestibular-optokinetic system must account for changes in head position with respect to gravity in order to produce compensatory oculomotor responses. The purpose of this experiment was to study the influence of gravity on the vestibulo-ocular reflex (VOR) in darkness and on visual-vestibular interaction in the pitch plane in human subjects using two different comparisons: (1) Earth-horizontal axis (EHA) rotation about an upright versus a supine body orientation, and (2) Earth-horizontal versus Earth-vertical (EVA) rotation axes. Visual-vestibular responses (VVR) were evaluated by measuring the slow phase velocity of nystagmus induced during sinusoidal motion of the body in the pitch plane (at 0.2 Hz and 0.8 Hz) combined with a constant-velocity vertical optokinetic stimulation (at +/- 36 degrees/s). The results showed no significant effect on the gain or phase of the VOR in darkness or on the VVR responses at 0.8 Hz between EHA upright and EHA supine body orientations. However, there was a downward shift in the VOR bias in darkness in the supine orientation. There were systematic changes in VOR and VVR between EHA and EVA for 0.2 Hz, including a reduced modulation gain, increased phase lead, and decreased bias during EVA rotation. The same trend was also observed at 0.8 Hz, but at a lesser extent, presumably due to the effects of eccentric rotation in our EVA condition and/or to the different canal input across frequencies. The change in the bias at 0.2 Hz between rotation in darkness and rotation with an optokinetic stimulus was greater than the optokinetic responses without rotation. During EHA, changes in head position relative to gravity preserve graviceptor input to the VVR regardless of body orientation. However, the modifications in VVR gain and phase when the rotation axis is aligned with gravity indicate that this graviceptive information is important for providing compensatory eye movements during visual-vestibular interaction in the pitch plane.

Non-NASA Center↗

Yaw sensory rearrangement alters pitch vestibulo-ocular reflex responses

Ten male subjects underwent two types of adaptation paradigm designed either to enhance or to attenuate the gain of the canal-ocular reflex (COR), before undergoing otolith-ocular reflex (OOR) testing with constant velocity, earth horizontal axis and pitch rotation. The adaptation paradigm paired a 0.2 Hz sinusoidal rotation about an earth vertical axis with a 0.2 Hz optokinetic stimulus that was deliberately mismatched in peak velocity or phase and was designed to produce short-term changes in the COR. Preadaptation and postadaptation OOR tests occurred at a constant velocity of 60 degrees/sec in the dark and produced a modulation component of the slow phase velocity with a frequency of 0.16 Hz due to otolithic stimulation by the sinusoidally changing gravity vector. Of the seven subjects who showed enhancement of the COR gain, six also showed enhancement of the OOR modulation component. Of the seven subjects who showed attenuation of the COR gain, five also showed attenuation of the OOR modulation component. The probability that these two cross-axis adaptation effects would occur by chance is less than 0.02. This suggests that visual-vestibular conditioning of the yaw axis COR also induced changes in the pitch axis OOR. We thus postulate that the central nervous system pathways that process horizontal canal yaw stimuli have elements in common with those processing otolithic stimuli about the pitch axis.

NASA Discipline Neuroscience↗