Results for “plastic” — Page 10

DOE OSTI2025

Technology Transfer from Fermi Research Alliance to Itasca Plastics for the purpose of Commercializing Scintillator Material

Researchers at the Fermi National Accelerator Laboratory (Fermilab) developed extruded plastic scintillator in the late 1990s, which was first used in the D-Zero experiment. Extruded plastic scintillator is currently produced at Fermilab and is used in particle detectors worldwide. The purpose of this CRADA is to transfer the knowledge related to the Fermilab extrusion process to Itasca Plastics, Inc. (Itasca Plastics). Much of this knowledge is contained in documentation that is in the public domain, although it is distributed over several communications (papers, conference records, etc.) and over several years. Under this CRADA Fermilab will assemble the information, provide it to Itasca Plastics and provide limited consulting to complete the knowledge transfer. If the transfer is successful, Itasca Plastics will be able to establish a U.S. commercial manufacturing capability for extruded scintillator material that can be used for high energy physics and commercial applications.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Performance of Vehicle Fuel System Elastomers and Plastics with Test Fuels Representing Gasoline Blended with 10% Ethanol (E10) and 16% Isobutanol (iBu16)

The compatibilities of fuel system elastomers and plastics were evaluated for test fuels containing 16 vol.% isobutanol (iBu16) and 10 vol.% ethanol (E10). Elastomers included two fluorocarbons, four acrylonitrile butadiene rubbers (NBRs), and one type of fluorosilicone, neoprene, and epichlorohydrin/ethylene oxide. Plastic materials included four nylon grades, three polyamides, polytetrafluoroethylene (PTFE), polyvinylidene fluoride (PVDF), ethylene tetrafluoroethylene (ETFE), polyphenylene sulfide (PPS), high-density polyethylene (HDPE), polybutylene terephthalate (PBT), polyoxymethylene (POM), flexible polyvinylchloride (PVC), polyetherimide (PEI), polyetheretherketone (PEEK), and a phenol formaldehyde reinforced with glass fiber (GFPF). For each polymer material, the volume, mass, and hardness were measured before and after drying. Dynamic mechanical analysis (DMA) measurements were also performed on the dried specimens.For the elastomer materials the measured properties were similar for both fuels. The fluorocarbons and fluorosilicone swelled the least (~20%), while more moderate (20-45%) expansion occurred for the two NBR hose grades and (ECO). HNBR, neoprene, and silicone exhibited high swelling and softening, which likely precludes their use in many fuel systems. For the plastic materials, the observed swell was low; Nylon 11 swelled around 15%, but otherwise, their measured swell was <10%. Many of the plastics also showed sensitivity to alcohol type, as the E10 test fuel often imparted appreciably higher swell than iBu16. In general, the plastic materials showed good compatibility with the iBu16 and E10 test fuels. Here, the sole exception was the PVC material, which was structurally degraded from exposure to either fuel type. Compositional analysis showed high fuel retention in Nylon 12 and PVC. PVC also experienced a significant reduction in plasticizer compounds following exposure, which resulted in embrittlement and an increase in the glass-to-rubber transition temperature.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2023

Comparative Techno-economic Analysis and Life Cycle Assessment of Producing High-Value Chemicals and Fuels from Waste Plastic via Conventional Pyrolysis and Thermal Oxo-degradation

The rapid rise in global plastic production in recent decades has resulted in the massive generation of plastic waste. Over 75% of the plastic waste generated in the United States was sent to landfills, with a meager 8.7% recycled. Plastics are valuable feedstocks for platform chemicals and fuels. Chemical upcycling of waste high-density polyethylene (HDPE) is gaining more attention as a potentially feasible and environmentally friendly plastic waste management technology. Conventional pyrolysis (CPY) and thermal oxo-degradation (TOD) are two chemical upcycling technologies actively researched for decomposing waste HDPE into valuable chemicals and fuels. However, there are few studies on the techno-economic analysis (TEA) and life cycle assessment (LCA) of these technologies for converting waste HDPE to valuable products. This study conducts a comparative TEA and LCA study of the thermochemical decomposition of waste HDPE to produce gaseous (ethylene and propylene) and liquid (naphtha, diesel, and wax) products by CPY and TOD. The study elucidates and compares the impact of hydrocracking longer chain hydrocarbons to produce more valuable products on the TEA and LCA. The TEA showed that the fixed capital investment could range from $\$32.5$ million for TOD without hydrocracking to $\$244$ million for CPY with hydrocracking scenarios. Annual revenues range from $\$28.1$ million to $\$71.5$ million in favor of scenarios with hydrocracking. However, the net present value ranges from $\$1.4$ million to $\$265.8$ million in favor of scenarios without hydrocracking. Sensitivity analysis showed that fixed capital cost, facility capacity, and product prices have the biggest impact on the process economics of the facilities, while utilities and waste transportation to refineries have the biggest impact on environmental impacts. Here, the LCA showed that primary products from scenarios without hydrocracking can be more environmentally friendly than virgin products from petroleum processes. However, TOD and CPY with hydrocracking primary products have more emissions than those of virgin products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Making Plasticized Polymer Electrolytes Stable Against Sodium Metal for High‐Energy Solid‐State Sodium Batteries

Abstract Solid polymer electrolytes based on plastic crystals are promising for solid‐state sodium metal (Na 0 ) batteries, yet their practicality has been hindered by the notorious Na 0 ‐electrolyte interface instability issue, the underlying cause of which remains poorly understood. Here, by leveraging a model plasticized polymer electrolyte based on conventional succinonitrile plastic crystals, we uncover its failure origin in Na 0 batteries is associated with the formation of a thick and non‐uniform solid electrolyte interphase (SEI) and whiskery Na 0 nucleation/growth. Furthermore, we design a new additive‐embedded plasticized polymer electrolyte to manipulate the Na 0 deposition and SEI formulation. For the first time, we demonstrate that introducing fluoroethylene carbonate (FEC) additive into the succinonitrile‐plasticized polymer electrolyte can effectively protect Na 0 against interfacial corrosion by facilitating the growth of dome‐like Na 0 with thin, amorphous, and fluorine‐rich SEIs, thus enabling significantly improved performances of Na//Na symmetric cells (1,800 h at 0.5 mA cm −2 ) and Na//Na 3 V 2 (PO 4 ) 3 full cells (93.0 % capacity retention after 1,200 cycles at 1 C rate in coin cells and 93.1 % capacity retention after 250 cycles at C/3 in pouch cells at room temperature). Our work provides valuable insights into the interfacial failure of plasticized polymer electrolytes and offers a promising solution to resolving the interfacial instability issue.

Zou, Peichao↗

DOE OSTI2025

Closed‐Loop Recyclable Vitrimer Plastics from PET Waste: A Design for Circularity

Plastics are essential to modern society, but their low recycling rates and inefficient end-of-life management pose a significant environmental challenge. Herein, the efficient strategy for upcycling postconsumer poly(ethylene terephthalate) (PET) waste into robust, closed-loop recyclable vitrimer plastics and composites is presented to address this issue. The catalyst-free aminolysis utilizes readily available amines to deconstruct diverse PET wastes into macromonomers, which are upcycled into vitrimers, exhibiting superior mechanical properties and exceeding the ultimate tensile stress and Young's Modulus of virgin PET by 80% and 150% respectively. These vitrimers exhibit excellent healability, shape memory, thermal reprocessability, and closed-loop chemical recyclability, enabling quantitative macromonomer recovery even from mixed plastic waste streams and glass/carbon fiber reinforced vitrimer (G/CFRV) composites. Furthermore, the vitrimer resin yields robust GFRV and CFRV composites with tensile strengths exceeding those of traditional epoxy composites by 100% and 80%, respectively, while maintaining complete chemical recyclability of both constituent materials. A preliminary technoeconomic analysis confirms the costeffectiveness and competitiveness of the facile PET deconstruction approach, which is potentially adaptable to other condensation polymers. Further, this study presents a facile approach to upcycling plastic waste into circular plastics and composites, offering a sustainable solution to global plastic waste management and fostering a circular economy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Primal interface debonding formulation for finite strain isotropic plasticity

In this work, a framework is developed for modeling ductile damage of nonlinear materials whose plastic deformation is characterized using rate independent classical plasticity. This method relies on the assumption that the free energy can be decomposed into elastic, plastic and damage parts. A thermodynamically consistent method is derived which satisfies the second law of thermodynamics in the Clausius–Duhem inequality form. The dissipation associated with plasticity takes place in the domain only, while damage dissipation is localized to the interface. The method is developed using Variational Multiscale ideas to obtain definitions of the interface fluxes within a primal formulation analogous to the Discontinuous Galerkin method, which ensures weakly vanishing interface gap prior to reaching a damage initiation criterion. The local nonlinear problem to calculate both plastic deformation gradient and damage variable follows an incremental approach similar to classical plasticity return mapping algorithm. This elastoplastic damage formulation is developed for material undergoing finite strain, and it naturally accommodates a trapezoidal traction separation law (TSL) whose shape can be varied to model either ductile interface behavior or brittle interface behavior. The formulation's performance is assessed through modeling a patch test and a compact tension specimen.

42 ENGINEERING↗

DOE OSTI2024

Quantitative kinetic rules for plastic strain-induced α - ω phase transformation in Zr under high pressure

Plastic strain-induced phase transformations (PTs) and chemical reactions under high pressure are broadly spread in modern technologies, friction and wear, geophysics, and astrogeology. However, because of very heterogeneous fields of plastic strain $E$ p and stress σ tensors and volume fraction c of phases in a sample compressed in a diamond anvil cell (DAC) and impossibility of measurements of σ and $E$ p , there are no strict kinetic equations for them. Here, we develop a kinetic model, finite element method (FEM) approach, and combined FEM-experimental approaches to determine all fields in strongly plastically predeformed Zr compressed in DAC, and specific kinetic equation for α-ω PT consistent with experimental data for the entire sample. Since all fields in the sample are very heterogeneous, data are obtained for numerous complex 7D paths in the space of 3 components of the plastic strain tensor and 4 components of the stress tensor. Kinetic equation depends on accumulated plastic strain (instead of time) and pressure and is independent of plastic strain and deviatoric stress tensors, i.e., it can be applied for various above processes. Our results initiate kinetic studies of strain-induced PTs and provide efforts toward more comprehensive understanding of material behavior in extreme conditions.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Influence of functional additives, fillers, and pigments on thermal and catalytic pyrolysis of polyethylene for waste plastic upcycling

Pyrolysis offers a relatively green and economical method to convert waste plastics into valuable chemicals and fuels without the need for harmful solvents, toxic chemicals, or costly high-pressure reactors. Despite its popularity among chemical upcycling technologies, industrial adoption suffers from feedstock heterogeneity, low-quality products, and catalyst deactivation. Most plastics in our daily lives are formulated with functional additives, fillers, and colorants. These additives remaining in end-of-life waste streams increase feedstock heterogeneity, creating a challenging issue in recycling plastics. Still, the potential impacts of additives on the chemical upcycling of plastics have been poorly understood. In this study, polyethylene compounded with a range of widely used additives (antioxidants, stabilizers, pigments, fillers, slip agents, and flame retardants) was subjected to both thermal pyrolysis and catalytic pyrolysis in different catalyst-to-feedstock contact modes. It showed that many inorganic additives, such as talc, kaolin, CaCO 3 , TiO 2 , carbon black, and zinc stearate, facilitated polymer decomposition during pyrolysis, increasing light hydrocarbons while also promoting aromatic and carbon residue formation. Conversely, antioxidants and stabilizers inhibited depolymerization, favoring heavier hydrocarbons. During catalytic pyrolysis with HZSM-5 zeolite, additives strongly enhanced aromatic and catalytic coke formation, especially when there was direct contact between plastics and catalysts. Although certain additives seem beneficial in the short term by promoting polymer cracking and improving the selectivity of aromatics, the transport of the additives and their degradation products and increased carbon coking can contaminate products, deactivate or modify catalysts, and foul reactors. These findings address a critical knowledge gap in effectively converting waste plastics via a greener route.

42 ENGINEERING↗

DOE OSTI2023

Thermodynamic Properties of Aggregate Coated by Different Types of Waste Plastic: Adhesion and Moisture Resistance of Asphalt-Aggregate Systems

The utilization of acidic aggregates in hot-mix asphalt (HMA) is often inevitable due to the limited supply of locally available aggregates, posing a potential threat of moisture damage to asphalt pavements. In this regard, the use of urban waste plastic to coat the low-quality aggregates is a promising way to improve the moisture resistance. This study fundamentally evaluated the compatibility between asphalt and plastic-coated aggregate by measuring surface energy, and for the first time compared the effects of different types of waste plastic including high-density polyethylene (HDPE), low-density polyethylene (LDPE), polyethylene terephthalate (PET), polyvinyl chloride (PVC), and polypropylene (PP). The plastic-coating significantly altered the chemistry of aggregate surface by increasing the nonpolar components and reducing the polar components. Such changes remarkably increased the dry adhesion energy between asphalt and aggregate and enhanced the wettability of aggregate. For the acidic aggregates, the polymeric treatment could decrease the value of wet adhesive, which indicated the debonding tendency in the presence of water was reduced. Finally, the energy ratios of the asphalt-aggregate combinations significantly increased by the surface pretreatment, which proved the effect of waste plastic coating on improving the moisture damage resistance of asphalt mixtures. By comparison, the HDPE coating was the most effective way to enhance the compatibility with asphalt, followed by PP and LDPE coatings. The PVC and PET coatings were investigated as the least effective way. In conclusion, this study cannot only contribute to the potential large-scale utilization of waste plastic but also remove the obstacles of using large quantities of acidic natural aggregate in asphalt pavements.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Global producer responsibility for plastic pollution

Brand names can be used to hold plastic companies accountable for their items found polluting the environment. We used data from a 5-year (2018–2022) worldwide (84 countries) program to identify brands found on plastic items in the environment through 1576 audit events. We found that 50% of items were unbranded, calling for mandated producer reporting. The top five brands globally were The Coca-Cola Company (11%), PepsiCo (5%), Nestlé (3%), Danone (3%), and Altria (2%), accounting for 24% of the total branded count, and 56 companies accounted for more than 50%. There was a clear and strong log-log linear relationship production (%) = pollution (%) between companies’ annual production of plastic and their branded plastic pollution, with food and beverage companies being disproportionately large polluters. Phasing out single-use and short-lived plastic products by the largest polluters would greatly reduce global plastic pollution.

Science & Technology - Other Topics↗

DOE OSTI2025

Compatibilization Strategy and Mechanism for Co-stabilizing Commingled Plastics and Pyrolyzed Rubber in Asphalt

Hot mix asphalt mixture is considered the ideal approach to reuse waste plastics in high-value applications because of its very high amount of usage in highway construction. However, the differences in polarity and density between polymers and asphalt lead to polymer coalescence and therefore the poor storage stability of modified asphalt. These challenges are exalted when recycling commingled plastics. This study introduced an innovative compatibilization strategy and mechanism for co-stabilizing commingled plastics and pyrolyzed rubber in asphalt. Commingled plastics were first grafted with maleic anhydride for surface activation, followed by reactive kneading with pyrolyzed rubber and crosslinking agent to form an integrated thermoplastic elastomer (ITPE) for asphalt modification. The mechanical, thermal, and interfacial behaviors of the ITPE were evaluated through tensile testing, thermogravimetric analysis, and scanning electron microscopy. The storage stability and rheological properties of the modified binder blends were evaluated through the cigar tube test and dynamic shear rheometer testing. Results demonstrated a successful formation of imide bonds in the ITPE, which can improve the strength, ductility, and thermal stability of rubber–plastic composites. Appropriate utilization of crosslinking agents can improve both rutting and fatigue resistance of ITPE-modified asphalt with good storage stability because of the co-existence of rigid plastic and soft rubbery regimes and the formation of a crosslink network. Furthermore, excessive content of crosslinker led to severe phase separation and reduced storage stability of modified binder blends. Extra crosslinker tended to float in asphalt because of its low density and caused an excessive formation of the crosslink network in the top section of the asphalt.

asphalt binder modifiers↗

DOE OSTI2020

Wet and dry plastic deposition data for western US National Atmospheric Deposition Program sites (2017-2019)

Raw plastic counts and calculated plastic deposition rates for 11 National Atmospheric Deposition Program (NADP) sites in the western USA recorded from 2017-2019. Samples were collected to determine plastic deposition rates in remote locations and identify the potential sources of plastic to the atmosphere. Samples were collected using an Aerochem Metrics Wet and Dry sampler. Wet deposition refers to the material retained on a 0.45-micron filter. Dry deposition refers to the dry only deposition collected using a Dry Side Insert (DSI) (Brahney et al. 2020). Plastics are identified as either fibers or particles (includes small colored films). Wet deposition rates are recorded weekly and dry plastic deposition rates are based on monthly sampling intervals. Sites included are Grand Canyon National Park (AZ03), Joshua Tree National Park (CA67), Rocky Mountain National Park (CO98), Niwot Ridge (CO02), Ashley National Forest (UT95), East River SFA (CO10)), Craters of the Moon National Park (ID03), Great Basin National Park (NV05), Canyonlands National Park (UT09), Bryce Canyon Nationa Park (UT99), and Wind River Range (WY06). Data collection is being published in collaboration with the Department of Energy's research project, "Constraining physical understanding of aerosol loading, biogeochemistry, and snowmelt hydrology from hillslope to watershed scale in the East River Scientific Focus Areas.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

End-of-Life Plastics Management: A Review: Mechanical recycling, pyrolysis and hydrocracking methods

End-of-life plastics present a significant challenge to achieving a sustainable economy. It is crucial to develop environmentally friendly technologies to process the waste streams beyond landfilling. This review provides a detailed overview of end-of-life plastics management, covering mechanical recycling, pyrolysis and hydrocracking methods. Mechanical recycling is the predominant technique employed on a large scale in recycling end-of-life plastics, and this review discusses the technoeconomic assessment and life cycle assessment (LCA) of mechanical recycling. This review also summarises key studies concentrating on chemical recycling techniques for handling end-of-life plastics. Among these, pyrolysis and hydrocracking are discussed in depth. Recent advancements and fundamentals of these two techniques are covered, highlighting their significance in tackling the plastic waste challenge. The prospects of scaling up pyrolysis and hydrocracking technologies are interpreted in terms of technical and economic feasibility. The discussion concludes with recommendations for future research to commercialise chemical recycling of end-of-life plastics.

Chemistry↗

DOE OSTI2024

Rupture Jumping and Seismic Complexity in Models of Earthquake Cycles for Fault Stepovers with Off-Fault Plasticity

ABSTRACT Fault stepovers are prime examples of geometric complexity in natural fault zones that may affect seismic hazard by determining whether an earthquake rupture continues propagating or abruptly stops. However, the long-term pattern of seismicity near-fault stepovers and underlying mechanisms of rupture jumping in the context of earthquake cycles are rarely studied. Leveraging a hybrid numerical scheme combining the finite element and the spectral boundary integral methods, FEBE, we carry out fully dynamic simulations of sequences of earthquakes and aseismic slip for both compressive and tensile stepovers with off-fault plasticity. We consider a rate-and-state friction law for the fault friction and pressure-sensitive Drucker–Prager plasticity for the off-fault bulk response. We observe that the accumulation of plastic deformation, an indication of off-fault damage, is significantly different in the two cases, with more plastic deformation projected in the overlapping region for the tensile stepover. The seismic pattern for a tensile stepover is more complex than for a compressive stepover, and incorporating plasticity also increases complexity, relative to the elastic case. A tensile stepover with off-fault plasticity shows rupture segmentation, temporal clustering, and frequent rupture jumping from one fault to another. These results shed light on possible mechanisms of rupture jumping in fault stepovers as well as the long-term evolution of the fault zone.

Geochemistry & Geophysics↗

DOE OSTI2022

Performance Testing of a Moving Bed Gasifier Using Coal, Biomass, and Waste Plastic Blends to Generate White Hydrogen

The objective of this DOE-funded project by the Electric Power Research Institute, Inc. (EPRI), Hamilton Maurer International (HMI) and Sotacarbo S.p.A. (Sotacarbo), is to qualify coal, biomass, and plastic waste blends based on performance testing of selected pellet recipes in a pilot-scale updraft moving-bed gasifier. The testing provides relevant data to advance the commercial-scale design of the moving-bed gasifier to be able to successfully use these feedstocks to produce hydrogen. In particular, the effects of the waste plastics on feedstock development (i.e., blending and pelletizing) and the resulting products (i.e., syngas compositions, organic condensate production, and ash characteristics) are a focus. The gasifier is Hamilton Mauer International, Inc. (HMI)’s moving-bed gasifier, which has been proven capable of gasifying nearly all coal ranks. It has also shown the ability in prior testing work to gasify wood chips. However, mixtures of these fuels with plastic wastes had not yet been prepared and gasified together. The feedstocks were prepared by California Pellet Mill (CPM) under contract to HMI. The technical tasks for this research project included: • Feed Procurement and Preparation: Nine different feedstocks were prepared from varying compositions of PRB coal, corn stover biomass, and car fluff waste plastics. Fuel pellets were produced by California Pellet Mill (CPM) and shipped to Sotacarbo’s test facility in Italy. • Test Plan Development: A test plan was created to define the test runs to be performed. The test plan detailed the different tests that were run, instrumentation used, extractive samples taken, and relevant figures of merit. • Gasifier Testing: Tests were performed in the pilot-scale gasifier at Sotacarbo using nine different fuel feedstocks generated from varying mixtures of coal, biomass, and plastic wastes. The testing provides information on gasification reaction efficiency/performance, yielding relevant data for models used to scale up the gasifier design. This task will also included work to reassemble the gasifier at Sotacarbo and perform a baseline 100% coal run. • Data Analysis and Reporting: Review of the data, determination of figures of merit, and interpretation of the results was reported. The results can be used to specify the range of feedstock blends that can be successfully gasified as well as quantify gasifier outputs based on specific blends. The tri-fuel pelletizing conducted at CPM and gasification testing results from Sotacarbo’s 30mm up draft moving bed gasifier are significant. Providing data for an established gasifier to help accelerate its updated design to be able to accommodate feedstocks composed of coal, biomass, and plastic waste. This should ultimately lead to development and commercialization of a lower cost, white hydrogen generation system.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2023

Performance Testing of a Moving-Bed Gasifier Using Coal, Biomass, and Waste Plastic Blends to Generate White Hydrogen

The objective of this DOE-funded project by the Electric Power Research Institute, Inc. (EPRI), Hamilton Maurer International (HMI) and Sotacarbo S.p.A. (Sotacarbo), is to qualify coal, biomass, and plastic waste blends based on performance testing of selected pellet recipes in a pilot-scale updraft moving-bed gasifier. The testing provides relevant data to advance the commercial-scale design of the moving-bed gasifier to be able to successfully use these feedstocks to produce hydrogen. In particular, the effects of the waste plastics on feedstock development (i.e., blending and pelletizing) and the resulting products (i.e., syngas compositions, organic condensate production, and ash characteristics) are a focus. The gasifier is Hamilton Mauer International, Inc. (HMI)’s moving-bed gasifier, which has been proven capable of gasifying nearly all coal ranks. It has also shown the ability in prior testing work to gasify wood chips. However, mixtures of these fuels with plastic wastes had not yet been prepared and gasified together. The feedstocks were prepared by California Pellet Mill (CPM) under contract to HMI. The technical tasks for this research project included: • Feed Procurement and Preparation: Nine different feedstocks were prepared from varying compositions of PRB coal, corn stover biomass, and car fluff waste plastics. Fuel pellets were produced by California Pellet Mill (CPM) and shipped to Sotacarbo’s test facility in Italy. • Test Plan Development: A test plan was created to define the test runs to be performed. The test plan detailed the different tests that were run, instrumentation used, extractive samples taken, and relevant figures of merit. • Gasifier Testing: Tests were performed in the pilot-scale gasifier at Sotacarbo using nine different fuel feedstocks generated from varying mixtures of coal, biomass, and plastic wastes. The testing provides information on gasification reaction efficiency/performance, yielding relevant data for models used to scale up the gasifier design. This task will also included work to reassemble the gasifier at Sotacarbo and perform a baseline 100% coal run. • Data Analysis and Reporting: Review of the data, determination of figures of merit, and interpretation of the results was reported. The results can be used to specify the range of feedstock blends that can be successfully gasified as well as quantify gasifier outputs based on specific blends. The tri-fuel pelletizing conducted at CPM and gasification testing results from Sotacarbo’s 30mm up draft moving bed gasifier are significant. Providing data for an established gasifier to help accelerate its updated design to be able to accommodate feedstocks composed of coal, biomass, and plastic waste. This should ultimately lead to development and commercialization of a lower cost, white hydrogen generation system.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Gasification of Mixed Blends of Coal, Biomass, and Plastic Waste

The objective of this DOE-funded project by the Electric Power Research Institute, Inc. (EPRI), Hamilton Maurer International (HMI) and Sotacarbo S.p.A. (Sotacarbo), is to qualify coal, biomass, and plastic waste blends based on performance testing of selected pellet recipes in a pilot-scale updraft moving-bed gasifier. The testing provides relevant data to advance the commercial-scale design of the moving-bed gasifier to be able to successfully use these feedstocks to produce hydrogen. In particular, the effects of the waste plastics on feedstock development (i.e., blending and pelletizing) and the resulting products (i.e., syngas compositions, organic condensate production, and ash characteristics) are a focus. The gasifier is Hamilton Mauer International, Inc. (HMI)’s moving-bed gasifier, which has been proven capable of gasifying nearly all coal ranks. It has also shown the ability in prior testing work to gasify wood chips. However, mixtures of these fuels with plastic wastes had not yet been prepared and gasified together. The feedstocks were prepared by California Pellet Mill (CPM) under contract to HMI. The technical tasks for this research project included: • Feed Procurement and Preparation: Nine different feedstocks were prepared from varying compositions of PRB coal, corn stover biomass, and car fluff waste plastics. Fuel pellets were produced by California Pellet Mill (CPM) and shipped to Sotacarbo’s test facility in Italy. • Test Plan Development: A test plan was created to define the test runs to be performed. The test plan detailed the different tests that were run, instrumentation used, extractive samples taken, and relevant figures of merit. • Gasifier Testing: Tests were performed in the pilot-scale gasifier at Sotacarbo using nine different fuel feedstocks generated from varying mixtures of coal, biomass, and plastic wastes. The testing provides information on gasification reaction efficiency/performance, yielding relevant data for models used to scale up the gasifier design. This task will also included work to reassemble the gasifier at Sotacarbo and perform a baseline 100% coal run. • Data Analysis and Reporting: Review of the data, determination of figures of merit, and interpretation of the results was reported. The results can be used to specify the range of feedstock blends that can be successfully gasified as well as quantify gasifier outputs based on specific blends. The tri-fuel pelletizing conducted at CPM and gasification testing results from Sotacarbo’s 30mm up draft moving bed gasifier are significant. Providing data for an established gasifier to help accelerate its updated design to be able to accommodate feedstocks composed of coal, biomass, and plastic waste. This should ultimately lead to development and commercialization of a lower cost, white hydrogen generation system.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2023

Sustainable production of plastic degrading enzymes

The 21st century faces the challenge of transitioning to a climate-neutral economy. This hurdle will need to be addressed in a myriad of approaches, including all societal spheres, as highlighted in several UN and EU reports, including new and accessed technologies. Among them, biotechnology can play a core role by exploiting its environmental benefits (e.g., substituting fossil-based products and expected greenhouse emission reductions). In some cases, biotech can even outperform fossil counterparts' features (e.g., the biodegradability of some bioplastics). Microalga is an attractive bioplastic feedstock in this scenario since it directly substitutes petroleum and captures CO2. However, albeit its environmental benefits, the microalgal process still needs to be tipped economically and the net-positive ecological impact improved to drive adoption. To that end, we envisioned the use of a green alga as a source of bioplastic feedstock and industrial enzymes, combining natural traits of microalgae with engineered properties in a resourceful process to petroleum-based products replacement. As proof of concept, we demonstrated that we could use C. reinhardtii, a green algae, to produce plastic-degrading enzymes. We assemble a vector to secrete PHL7, a recently described PETase, capable of degrading post-consumer PET plastic. We successfully engineered the cell line to secrete the plastic-degrading enzyme. We confirmed the secretion of the enzyme by observing halos in agar plates supplemented with plastic dispersions, enzymatic assays, zymograms, and protein sequencing of supernatant samples. This approach allows using green algae to replace petrochemical-derived plastic while producing the tool necessary to recycle existing plastics sustainably.

Dutra Molino, Joao Vitor↗