SEARCH · Search NASA

Results for “pressure management”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Long-life assessment of graphite epoxy materials for Space Station Freedom pressure vessels

Graphite/epoxy composite overwrapped pressure vessels are being considered for use on Space Station Freedom because of their light weight and high efficiency. These composite pressure vessels weigh roughly one-third of comparable all-metal aluminum pressure vessels, and could result in a 15,000-lb weight saving for the propulsion and fluid management and distribution systems. These vessels must resist failures under sustained pressure loads for crew safety considerations and adequate protection of the space structure during their 30-yr life. Weibull statistical analysis techniques have been applied, and a model developed, for predicting long-term stress-rupture behavior based on published short-term test data on composite strands and pressure vessels. Graphite/epoxy materials are calculated to have a 99.99-percent probability of surviving stress rupture for 30 yr under a sustained load of 50 percent ultimate failure strength. Stress-rupture lifetimes are predicted to increase as the size of the pressure vessels increases in support of the viscoelastic load-transfer mechanism proposed for stress rupture of fiber/epoxy composite materials.

Thomas, Donald A.↗

DOE OSTI2025

Leveraging Radiofrequency Identification Success Beyond Hazardous Material Inventory Management at a National Laboratory

Effective inventory management can be overshadowed by conflicting priorities in organizational procedures, particularly in research-focused institutions such as national laboratories that handle expensive, delicate, and hazardous materials. Here, this study investigated the potential of radiofrequency identification (RFID) technology, currently used for hazardous chemical inventory, in applications with higher metal interference and absorption, specifically pressure release device (PRD) compliance and nuclear container management, at Lawrence Livermore National Laboratory (LLNL). This study was done to document best practices to enhance inventory identification speeds for inventory reconciliation and inventory recall and to explore optimal configurations for RFID implementation compared to traditional manual methods of equipment management. Tests were conducted to determine the ideal RFID tag orientation (read at angles of 0°, 90°, and 270°), various container layouts (linear, separated, curved, operational), and ID methods such as manual, barcode, and RFID performing three trials per method per orientation. Results indicated that 0° was the optimal read angle for minimizing metallic interference, and the operational and curved arrangements significantly outperformed the linear and separated configurations in read speed. 3D printed mounts were developed and tested, increasing the read range of the RFID reader by up to 235% in cases of high metallic interference. The RFID technology demonstrated an average speed increase of 65% over a simplified manual identification, which supports the conclusion that RFID is a more efficient method for large hazardous inventory management and equipment reconciliation. Additionally, capturing meta-data, such as location and date, can be used to query for inventory recall and automated updating of record information.

42 ENGINEERING↗

NASA NTRSDate not supplied

Validation of Two-Phase Flow Modeling Techniques in Loci-Stream Using Axial Jet Pressure Control and Autogenous Pressurization Experiments

Improvements to computational fluid dynamics modeling of cryogenic fluid management operations are presented with experimental validations. Modeling improvements includes utilizing improved delayed detaches eddy simulation to more effectively model turbulence compared to the Reynolds-averaged Navier Stokes modeling, modeling temperature dependent tank solid properties to capture large variation in thermodynamic properties at cryogenic conditions, modeling real gas equation of state for hydrogen instead of ideal gas behavior, and an on-going effort to improve interface turbulence transport for the volume of fluid method. Two flight-scale ground tests, five K-site tank axial jet pressure control experiments and an Engineering Design Unit tank autogenous pressurization experiment are validated and show the effectiveness of the improved modeling techniques. The successful validation establishes further trust in these models for flight project support and provides a pathway for maturation of in-development interface turbulence damping model for the volume of fluid method for more generalized applications.

CFD↗

NASA NTRSDate not supplied

Validation of Two-phase Flow Modeling Techniques in Loci-Stream using Axial Jet Pressure Control and Autogenous Pressurization Experiment

CFD↗

NASA NTRS1992

The VTRE Program: An overview

The Vented Tank Resupply Experiment (VTRE) Program is a NASA In-Space Technology Experiments Program (IN-STEP) that will develop, and fly a small, low cost space experiment to investigate, develop, and acquire needed data to extend and advance the technology of capillary vane fluid management devices to applications requiring direct venting of gas from tanks in low-gravity. GAS venting may be required for control of pressure, or to allow low-g fill of a tank with liquid while holding a constant tank back pressure by gas venting. Future space applications requiring these fluid management capabilities include both cryogenic and Earth storable fluid systems. The experiment is planned as a Shuttle Hitchhiker payload, and will be developed around two transparent tanks equipped with capillary vane devices between which a test liquid can be transferred. Experiments will be conducted for vented transfer, direct venting, stability of liquid positioning to accelerations within and significantly above the design values, and fluid reorientation by capillary wicking of liquid into the vane device following intentional liquid upset.

Bailey, William J.↗

DOE OSTI2023

Enhanced internal condensation of R1233zd(E) on micro- and nanostructured copper and aluminum surfaces

In-tube condensation of refrigerants is an important process which affects thermal efficiency in many applications, ranging from refrigeration and air conditioning to electronics thermal management. In-tube heat transfer and pressure drop are important to heat exchanger sizing and design. Here, in this work, micro- and nanostructured surfaces are applied to the internal wetted areas of copper and aluminum mini-channels to enhance the condensation heat transfer coefficient of hydrofluorocarbon R1233zd(E) refrigerant. To achieve scalable nanomanufacturing, surfaces were uniformly structured by relying on hydrochloric acid etching of aluminum and chemical oxidation of copper. The etched aluminum surfaces exhibited a 150% increase in heat transfer coefficient compared to smooth aluminum channels at specific qualities, with a 66% heat transfer coefficient improvement for complete phase change from saturated vapor to saturated liquid. Copper oxide structures showed no discernable difference in thermal-hydraulic performance when compared to smooth copper channels. Critical dimensionless parameters governing the heat transfer enhancement were identified by varying the tube internal diameter (2.3 mm to 4.7 mm), refrigerant mass flux (50 to 300 kg/(m 2 ·s)), and refrigerant quality (0 to 1). The dimensionless parameters include the Bond number normalized to the condensate film thickness, and the Weber number modified by the vapor friction factor. The relatively small increase in pressure drop (< 10%) associated with these surface enhancements further supports the promise of this method. The scalable and cost-effective techniques used to create these aluminum microstructures may reduce manufacturing cost when compared with current enhancement approaches such as extrusion, drawing, and welding.

42 ENGINEERING↗

DOE OSTI2023

Automotive Silicon Carbide Power Module Cooling With A Novel Modular Manifold And Embedded Heat Sink

The next generation of integrated power electronics packages will implement wide-bandgap devices with ultrahigh device heat fluxes. Although jet impingement has received attention for power electronics thermal management, it is not used in commercial electric vehicles (EVs) because of the associated pressure drop and reliability concerns. Here, in this paper, we present a modular thermal management system designed for automotive power electronics. The system achieves superior thermal performance to benchmarked EVs, while adhering to reliability standards and with low pumping power. The system utilizes a low-cost and lightweight plastic manifold to generate jets over an optimized heat sink, which is embedded in the direct-bonded-copper (DBC) substrate. The embedded heat sink concept leverages additive manufacturing to add elliptical pin fins to the DBC substrate. The heat sink geometry is optimized for submerged jet impingement using a unit-cell model and an exhaustive search algorithm. The model predictions are validated using unit-cell experiments. A full-scale power module model is then used to compare the DBC-embedded heat sink against direct DBC cooling and baseplate-integrated heat sinks for single-sided (SS) and double-sided (DS) cooling concepts. Using the SS and DS DBC-embedded cooling concepts, the models predict a thermal resistance that represents a reduction of 75% and 85% compared to the 2015 BMW i3, respectively, for the same water-ethylene glycol inverter flow rate. We have shown that an inverter with a 100-kilo-Watt-per-liter power density is achievable with the proposed design.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2025

DEDUPKV: A Space-Efficient and High-Performance Key-Value Store via Fine-Grained Deduplication

Log-Structured Merge Tree (LSM-tree) based key-value stores excel in write-intensive environments but suffer from data duplication, consuming up to 49% of storage space in LSM-tree-based key-value store deployments. Traditional solutions like compression and coarse-grained file system-level deduplication introduce overhead or have limited effectiveness. In this study, we propose DedupKV, a fine-grained deduplication framework tailored for LSM-tree, maximizing data reduction efficiency while minimizing write stalls and read overheads. DedupKV features three key innovations: (1) FLUSH-integrated inline deduplication, which removes duplicates during memory-to-storage writes; (2) WAL file-based offline deduplication, repurposing write-ahead logs to avoid double writes; and (3) elastic execution, dynamically balancing inline and offline deduplication based on memory pressure and workload intensity. Additionally, dynamic granularity management reduces deduplication metadata overhead. We implemented these four ideas in RocksDB for the first time and conducted experiments in a Linux environment. Our evaluation shows that WAL file-based offline deduplication and DedupKV outperform BlobDB by 33% and 23%, respectively, in write-heavy workloads, while reducing write amplification by 1.2 ×, 2 ×, and 1.6 × for real KV datasets.

Jamil, Safdar [Sogang University]↗

NASA NTRS1992

Evolution design requirements and design strategy

Space Station Freedom (SSF) has undergone numerous design changes during the rephasing and restructuring activities occurring in 1989 and 1990/91, respectively. One direct result of these changes is that the Station has become more complex and compact which requires that future modifications to the Station be carefully planned and analyzed in conjunction with the baseline design process. This will ensure that the configuration has adequate design features and flexibility to accommodate the future capability and element upgrades. Six critical growth requirements (electrical power, thermal control, pressurized volume, structures, EVA equipment, and data management) have been identified and baselined in the Level I Program Requirements Document (PRD) and the Level II Program Definition and Requirements Document (PDRD). The approach to meeting the growth requirements will be to minimize the impact on the baseline design in the areas of weight, power, and development cost. The specifics of these requirements, with regard to scarring and implementation during the Follow-On and Evolution phases of SSF, are detailed in this paper.

Monell, D. W.↗

NASA NTRS2005

X-43A Fluid and Environmental Systems: Ground and Flight Operation and Lessons Learned

The X-43A Hyper-X program demonstrated the first successful flights of an airframe integrated scramjet powered hypersonic vehicle. The X-43A vehicles established successive world records for jet-powered vehicles at speeds of Mach 7 and Mach 10. The X-43A vehicle is a subscale version of proposed hypersonic reconnaissance strike aircraft. Scaled down to a length of 12 ft (3.66 m), the lifting body design with high fineness ratio resulted in very small internal space available for fluid systems and their corresponding environmental conditioning systems. Safe testing and operation of the X-43A fluid and environmental systems was critical for mission success, not only for the safety of the flight crew in the NASA B-52B carrier aircraft, but also to maintain the reliability of vehicle systems while exposed to dynamics and hostile conditions encountered during the boost trajectory. The X-43A fluid and environmental systems successfully managed explosive, pyrophoric, inert, and very high pressure gases without incident. This report presents a summary of the checkout and flight validation of the X-43A fluid systems. The testing used for mission assurance is summarized. System performance during captive carry and launch flights is presented. The lessons learned are also discussed.

Vachon, Michael Jacob↗

NASA NTRS2012

CRYogenic Orbital TEstbed Ground Test Article Thermal Analysis

The purpose of this study was to anchor thermal and fluid system models to CRYOTE ground test data. The CRYOTE ground test artide was jointly developed by Innovative Engineering Solutions, United Launch Alliance and NASA KSC. The test article was constructed out of a titanium alloy tank, Sapphire 77 composite skin (similar to G10), an external secondary payload adapter ring, thermal vent system, multi layer insulation and various data acquisition instrumentation. In efforts to understand heat loads throughout this system, the GTA (filled with liquid nitrogen for safety purposes) was subjected to a series of tests in a vacuum chamber at Marshall Space Flight Center. By anchoring analytical models against test data, higher fidelity thermal environment predictions can be made for future flight articles which would eventually demonstrate critical cryogenic fluid management technologies such as system chilldown, transfer, pressure control and long term storage. Significant factors that influenced heat loads included radiative environments, multi-layer insulation performance, tank fill levels and pressures and even contact conductance coefficients. This report demonstrates how analytical thermal/fluid networks were established and includes supporting rationale for specific thermal responses.

Piryk, David↗

NASA NTRS2013

Development of an Indexing Media Filtration System for Long Duration Space Missions

The effective maintenance of air quality aboard spacecraft cabins will be vital to future human exploration missions. A key component will be the air cleaning filtration system which will need to remove a broad size range of particles derived from multiple biological and material sources. In addition, during surface missions any extraterrestrial planetary dust, including dust generated by near-by ISRU equipment, which is tracked into the habitat will also need to be managed by the filtration system inside the pressurized habitat compartments. An indexing media filter system is being developed to meet the demand for long-duration missions that will result in dramatic increases in filter service life and loading capacity, and will require minimal crew involvement. The filtration system consists of three stages: an inertial impactor stage, an indexing media stage, and a high-efficiency filter stage, packaged in a stacked modular cartridge configuration. Each stage will target a specific range of particle sizes that optimize the filtration and regeneration performance of the system. An 1/8th scale and full-scale prototype of the filter system have been fabricated and have been tested in the laboratory and reduced gravity environments that simulate conditions on spacecrafts, landers and habitats. Results from recent laboratory and reduce-gravity flight tests data will be presented. The features of the new filter system may also benefit other closed systems, such as submarines, and remote location terrestrial installations where servicing and replacement of filter units is not practical.

Filtration↗

NASA NTRS2013

Development of an Indexing Media Filtration System for Long Duration Space Missions

The effective maintenance of air quality aboard spacecraft cabins will be vital to future human exploration missions. A key component will be the air cleaning filtration system which will need to remove a broad size range of particles including skin flakes, hair and clothing fibers, other biological matter, and particulate matter derived from material and equipment wear. In addition, during surface missions any extraterrestrial planetary dust, including dust generated by near-by ISRU equipment, which is tracked into the habitat will also need to be managed by the filtration system inside the pressurized habitat compartments. An indexing media filter system is being developed to meet the demand for long-duration missions that will result in dramatic increases in filter service life and loading capacity, and will require minimal crew involvement. These features may also benefit other closed systems, such as submarines, and remote location terrestrial installations where servicing and replacement of filter units is not practical. The filtration system consists of three stages: an inertial impactor stage, an indexing media stage, and a high-efficiency filter stage, packaged in a stacked modular cartridge configuration. Each stage will target a specific range of particle sizes that optimize the filtration and regeneration performance of the system. An 1/8th scale and full-scale prototype of the filter system have been fabricated and have been tested in the laboratory and reduced gravity environments that simulate conditions on spacecrafts, landers and habitats. Results from recent laboratory and reducegravity flight tests data will be presented.

Filtration↗

DOE OSTI2024

Multi-physics Modeling of Radiative Heat Transfer and Fluid Flow for the Reactor Cavity Cooling System

High-temperature gas-cooled reactors (HTGRs) are notable for their high thermal efficiency and potential for combined heat and power applications. These reactors are particularly appealing due to their advanced passive safety features. HTGRs utilize passive safety systems that function without requiring active components like pumps or compressors during emergencies. These reactor designs depend on a Reactor Cavity Cooling System (RCCS) to manage decay heat removal from the reactor pressure vessel (RPV) during accident conditions. The RCCS consists of vertical rectangular channels known as "risers" or riser ducts positioned around the RPV. These risers receive heat from the RPV through both convective and radiative heat transfer mechanisms. Understanding the interplay of multiple physical phenomena, such as fluid dynamics, heat transfer, and neutron interactions, is essential for the effective design and operation of nuclear reactors, particularly for systems like the RCCS. Multi-physics simulations provide a comprehensive approach to studying these interactions, offering detailed insights and enhancing accuracy. They are especially important in RCCS designs, where the interaction between radiative and convective heat transfer can significantly impact system performance. By leveraging multi-physics simulations, complex reactor behaviors can be modeled without compromising the fidelity of the underlying physical processes. This work aims to establish a robust methodology for coupling multiple physical processes in an air-cooled RCCS. By focusing on validating this multi-physics approach, the study involves designing test cases that simulate various conditions to verify the numerical models employed. The outcomes of this research will provide critical insights for accurately modeling and optimizing complex nuclear systems like the RCCS.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

Coexistence Praxis: The Role of Resource Managers in Wolf-Livestock Interactions on Federal Lands

In resource management, new terms are frequently introduced, reflecting ongoing evolution in the theory and practice of ecology and governance. Yet understandings of what new concepts mean, for whom, and what they imply for management on the ground can vary widely. Coexistence—a prominent concept within the literature and practices around human-wildlife conflict and predator management—is one such term: widely invoked and yet poorly defined. While for some coexistence is the latest paradigm in improving human-wildlife relations, the concept remains debated and indeed even hotly contested by others—particularly on the multiple-use public lands of the American West, where gray wolf conservation, livestock production, and the claims of diverse stakeholders share space. The multiple meanings of coexistence present serious challenges for conservation practice, as what the concept implies or requires can be contested by those most central to its implementation. In this study we examine wolf-livestock management—a classic case of human-wildlife conflict—by focusing on the experiences and perspectives of U.S. Forest Service (USFS) managers. We reviewed coexistence's multivalence in the literature, complementing semi-structured interviews conducted with USFS employees on case study forests from across the western states. Through this, we highlight the complexity and multi-dimensionality of the concept, and the unique yet under-explored perspective that resource managers bring to these debates. This work draws on insights from political ecology to emphasize the situatedness of manager practice—taking place within a broader set of relations and contextual pressures—while extending political ecologists' traditional focus on the resource user to a concern with the resource manager as a key actor in environmental conflicts. Through our engagement with the experiences and perceptions of USFS managers, who must balance conservation aims with long-established land uses like livestock grazing, we hope to clarify the various dimensions of coexistence. Our hope is that this work thus increases the possibility for empathy and collaboration among managers and stakeholders engaged in this complex socio-ecological challenge.

Martin, Jeff Vance↗

DOE OSTI2025

CO2 hydrate crystal thickening, morphology, and Raman spectroscopy in a microfluidic device

Gas hydrates are a solid, crystalline form of water that often form at low temperatures and high pressures. Carbon dioxide (CO2) hydrates may form during carbon dioxide capture and storage (CCS) processes. These solid compounds may form in CO2 pipelines, potentially leading to a full blockage and process shutdown for plug removal. On the other hand, formation of CO2 hydrates may be desired for CO2 capture and separation. In either case, understanding the growth behavior and nature of the hydrates is vital to managing these CCS processes. Using a high-pressure, transparent microfluidic reactor, the crystalline film thickening of CO2 hydrates was observed and measured through visual microscopy and Raman spectroscopy. The impact of subcooling, pressure, and CO2 flow rate was investigated, and only CO2 flow rate was found to have a significant impact on the overall thickness of the film. Visual observations and Raman spectroscopy measurements confirmed that two distinct hydrate layers formed during thickening, one which was more porous than the other. The capillary-like channels in the porous layer indicated a mechanism for mass transfer of water through the hydrate layer. A model was developed based on this observation, and it was fit to the thickening data in order to obtain mass transfer coefficients. Results of this study can be applied to CO2 hydrate formation in pipelines and near porous media used for CO2 capture.

Wadsworth, Lindsey [Colorado School of Mines, Gold↗

DOE OSTI2020

Quarterly Management Document – FY20, 1st Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications

During the first quarter of FY20, efforts focused on calibrating a computational model using experimental data. The experimental creep data obtain from specimens containing weld metal exhibit considerable inherent variability making calibration of the computational difficult and may not result in an accurate model.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Quarterly Management Document – FY20, 2nd Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications

During the 2nd quarter of FY20, calibration of the creep model was made using experimental creep data on base metal at temperatures between 700-800 C. The model simulated primary and secondary creep behavior at these temperatures but tended to over estimate creep strain in the tertiary regime at 700 C while underestimating it at higher temperatures. Additional issues were also discovered and will be looked at in greater detail in the 3rd quarter of FY20.

36 MATERIALS SCIENCE↗