Search NASA⌕ Search

SEARCH · Search NASA

Results for “rate of penetration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Destabilization of yttria-stabilized zirconia induced by molten sodium vanadate-sodium sulfate melts

The extent of surface destabilization of ZrO2 - 8 wt percent Y2O3 ceramic disks was determined after exposure to molten salt mixtures of sodium sulfate containing up to 15 mole percent sodium metavanadate (NaVO3) at 1173 K. The ceramic surface was observed to transform from the cubic/tetragonal to monoclinic phase, concurrent with chemical changes in the molten salt layer in contact with the ceramic. Significant attack rates were observed in both pure sulfate and metavanadate sulfate melts. The rate of attack was found to be quite sensitive to the mole fraction of vanadate in the molten salt solution and the partial pressure of sulfur trioxide in equilibrium with the salt melt. The observed parabolic rate of attack is interpreted to be caused by a reaction controlled by diffusion in the salt that penetrates into the porous layer formed by the destabilization. The parabolic rate constant in mixed sodium metavanadate - sodium sulfate melts was found to be proportional to the SO3 partial pressure and the square of the metavanadate concentration. In-situ Raman spectroscopic measurements allowed simultaneous observations of the ceramic phases and salt chemistry during the attack process.

Nagelberg, A. S.↗
NASA NTRS1987

Feedback control for penetrating a downburst

Feedback logic is given that produces satisfactory penetration of an aircraft through a severe downburst. The logic has two parts: (1) A switch that calls for full throttle and tight climb-rate-hold feedback logic when the magnitude of headwind-rate exceeds a threshold level; this switch stays on until re-set by the pilot after penetration of the downburst. (2) A tight climb-rate-hold autopilot, using feedback of pitch-angle to angle-of-attack. After penetration, recovery to steady climbing flight is aided by using feedback of airspeed deviation to throttle. Insights on control strategy are gained from an analysis of energy changes during flight through a downburst. Closed-loop simulations are given for a 727 aircraft penetrating severe downbursts on take-off. Boeing's recommendation of constant pitch angle was confirmed as an excellent feedback control strategy.

Bryson, Arthur E., Jr.↗
DOE OSTI2022

Simulations of graphite boronization: A molecular dynamics study of amorphization resulting from bombardment

The molecular dynamics code LAMMPS was used to simulate the bombardment of a graphite structure by atomic boron with impact energies ranging from 50–250 eV. The transient structural evolution, penetration depth, and amorphous layer thickness were analyzed. Simulations show that larger impact energies lead to a greater volume of amorphization and penetration of boron, but that the growth rate of the amorphous layer decreases with increasing fluence. Furthermore, the change in surface chemistry of the amorphized structures was studied using the ReaxFF formalism, which found that the amorphization process introduces dangling bonds thus increasing reactivity in the amorphous region.

74 ATOMIC AND MOLECULAR PHYSICS↗
NASA NTRS1975

Effort of spanwise variation of turbulence on the normal acceleration of airplanes with small span relative to turbulence scale

A rigid airplane with an unswept wing is analyzed. The results show that the power spectrum, relative to that for a one-dimensional turbulence field, is significantly attenuated at the higher frequencies even for airplanes with arbitrarily small ratios of span to scale of turbulence. This attenuation is described by a simple weighting function of frequency that depends only on aspect ratio. The weighting function, together with the attenuation due to the unsteady flow of gust penetration, allows the determination of the average rate of zero crossings for airplanes having very small spans without recourse to an integral truncation which is often required in calculations based on a one-dimensional turbulence field.

Pratt, K. G.↗
NASA NTRS1976

Results of phase change paint tests of 0.040 scale 50% forebody models (82-0) of the space shuttle orbiter in the AEDC VKF B hypersonic wind tunnel (OH75)

Post-test information and data are presented from phase change paint, aerodynamic heating wind tunnel tests of a Rockwell International space shuttle orbiter forebody model. These tests were conducted in the Arnold Engineering and Development Center von Karman Facility Tunnel B Hypersonic Wind Tunnel. The purpose of these tests was to determine the effect of simulated orbiter protuberances and penetrations (including RCS nozzles) on aerodynamic heating rates during simulated entry conditions.

Dye, W. H.↗
NASA NTRS1982

An experimental study of the ice column habit transitions

The influence of supersaturation on column growth of ice crystals forming from atmospheric water vapor was investigated. A high density of crystals was generated on a glass fiber cooled by liquid N2 in a thermal diffusion chamber. Attention was focused on a neighbor-free hollow prism during a stepwise decrease in supersaturation while the crystal temperature was maintained constant. Another experiment involved epitaxial growth of ice crystals on CuS, where nonthickening crystals could only be grown below -7 C. A critical supersaturation was found to be necessary for growth of the basal plane. Beyound the critical value, surface kinetics do not control the growth rate, which is then dominated by the penetration of water molecules through the diffusion field surrounding the crystal.

Cho, N.↗
NASA NTRS1928

The Effects of Fuel and Cylinder Gas Densities on the Characteristics of Fuel Sprays for Oil Engines

This investigation was conducted as a part of a general research on fuel-injection engines for aircraft. The purpose of the investigation was to determine the effects of fuel and cylinder gas densities with several characteristics of fuel sprays for oil engines. The start, growth, and cut-off of single fuel sprays produced by automatic injection valves were recorded on photographic film by means of special high-speed motion-picture apparatus. This equipment, which has been described in previous reports, is capable of taking twenty-five consecutive pictures of the moving spray at the rate of 4,000 per second. The penetrations of the fuel sprays increased and the cone angles and relative distributions decreased with increase in the specific gravity of the fuel. The density of the gas into which the fuel sprays were injected controlled their penetration. This was the only characteristic of the chamber gas that had a measurable effect upon the fuel sprays. Application of fuel-spray penetration data to the case of an engine, in which the pressure is rising during injection, indicated that fuel sprays may penetrate considerably farther than when injected into a gas at a density equal to that of the gas in an engine cylinder at top center.

Joachim, W F↗
NASA NTRS2016

The Antarctic Analogy for Ancient Lakes at Gale Crater, Mars

In place of the dual choice of “warm and wet” versus “cold and dry” Mars, we reconcile in this paper the notion of a cold Mars with the notion of wet Mars. Both the geological evidences at Gale's for the presence of liquid water during the Hesperian (Grotzinger et al., Science, 350 (6257), 2015) and the failure of climate models make Mars warm (Wordsworth, Review of Earth and Planetary Science, 44, 1-31, 2016) suggested that an alternative scenario could be envisioned. The lake Untersee, Antarctica is an inspiring example of how an aqueous environment can survive for an extended period of the time in a place where the day average temperatures never, ever, each 273K. The key process which maintains a liquid, potentially habitable, environment under the ice is the subaqueous melting of a glacial dam in contact with the lake which provides a constant latent heat flux into the lake (McKay et al, in preparation) Our calculations showed that for certain range of pressures, temperatures and ice optical properties, a large body of water at Gale's will not freeze solid even if the surface temperatures are at all times well below freezing. The rather high sublimation rates of ice at Mars', the sunlight penetrating the ice and the geothermal flux contribute to stabilize the solid/liquid interface at a certain depth. We found that for a mean annual temperature of 245K ice thicknesses range from 3-10 meters which are comparable values to the range of those for the Antarctic lakes (2-7m). Thus, the ice potentially gets thin enough to let sediments penetrate the ice (Rivera-Hernandez et al., in preparation) and geological features associated with aqueous environments may still be possible with a perennially-covered lake, on cold, but wet planet. The Antarctic lakes model is engaging as it relaxes the requirement for a long-lived active hydrological cycle.

The lake Untersee↗
NASA NTRS2008

Micro-Structural Response of DP 600 to High Strain Rate Deformation

The object of this study was to investigate the micro-structural response of DP 600 subjected to high strain rate, ballistic impact tests. The ballistic tests were conducted using normal impact of a hardened steel penetrator into a 2 mm thick sheet of DP 600. The average strain rates produced from this test method are on the order of 10(exp 5)/s. Electron microscopy was used to investigate the microstructure before and after high strain rate deformation. A variation in material response was observed between tests conducted at 0.8 x 105 and 25 x 10(exp 5)/s.

Hamburg, Brian↗
DOE OSTI2020

A Low-Cost Durable Na-FeCl2 Battery with Ultrahigh Rate Capability

Na-based batteries have long been regarded as an inexpensive, sustainable candidate for large-scale stationary energy storage applications. Unfortunately, the market penetration of conventional Na-NiCl2 batteries is approaching its limit for several reasons, including limited rate capability and high Ni cost. Herein, a Na-FeCl2 battery operating at 190 °C is reported that allows a capacity output of 116 mAh g-1 at an extremely high current density of 33.3 mA cm-2 (˜0.6C). The superior rate performance is rooted in the intrinsically fast kinetics of the Fe/Fe2+ redox reaction. Furthermore, it is demonstrated that a small amount of Ni additive (10 mol%) effectively mitigates capacity fading of the Fe/NaCl cathode caused by Fe particle pulverization during long-term cycling. The modified Fe/Ni cathode exhibits excellent cycling stability, maintaining a discharge energy density of over 295 Wh kg-1 for 200 cycles at 10 mA cm-2 (˜C/5).

Zhan, Xiaowen↗
DOE OSTI2019

Effect of iron and silica nanoparticles’ size on in vitro human skin binding and penetration

This in vitro skin study determined absorption, diffusion, and binding rates of four [14C]-labeled nanoparticles (NPs): 12 nm Fe 3 O 4 , 32 nm Fe 3 O 4 @SiO 2 , 33 nm SiO 2 , and 78 nm SiO 2 in each layer of human cadaver skin. In vitro microdialysis device and flow-through skin diffusion system were used to measure the binding affinity to the stratum corneum (SC) and permeability into/through skin layer of the four NPs with different physical–chemical properties, respectively, in short (30 min) and/or long (24 hours) exposures. Results show that NP size is an important factor affecting NP percutaneous absorption. The 12 nm Fe 3 O 4 NPs reached the SC and viable epidermis; 32 nm Fe 3 O 4 @SiO 2 core/shell NPs only reached SC. However, 33 nm and 78 nm silica NPs did not permeate SC. Similar patterns were observed for NP binding affinity to SC and dermatopharmacokinetic analysis using the tape stripping method. The binding affinity determination may be a useful method to efficiently screen skin penetration of NPs.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Photovoltaic Inverter Momentary Cessation: Recovery Process is Key

Momentary cessation refers to an inverter control mode. When the inverter terminal voltage falls below (or exceeds) a certain level, the inverter ceases to output any current, but attempts to maintain (or quickly regain) phase-locked loop synchronization to allow for quick reinjection of current when the voltage recovers to a certain point. This paper presents a photovoltaic (PV) momentary cessation model developed in PSS/E. Simulations are presented for a high voltage transmission line fault contingency in the Hawaiian island of Oahu power system on a validated PSS/E model, modified to include a custom distributed PV inverter model, and different near-future distributed PV penetration levels. Simulations for the island power system include different penetration levels of PV, and different recovery times (ramp rates and delays) after momentary cessation. The results indicate that during low voltage events, such as faults, momentary cessation can produce severe under frequency events, causing significant load shed and shortly thereafter, in some cases, over frequency events that cause generation to trip offline. The problem is exacerbated with higher penetration levels of PV. If momentary cessation is used (as is typically the case for distribution-connected resources), the recovery process after momentary cessation should be carefully considered to minimize impacts to bulk power system stability.

14 SOLAR ENERGY↗
NASA NTRS2015

Numerical Experiments of Counterflowiing Jet Effects on Supersonic Slender-Body Configurations

Previous studies have demonstrated that the use of counterflowing jets can greatly reduce the drag and heat loads on blunt-body geometries, especially when the long penetration mode jet condition can be established. Previously, the authors had done some preliminary numerical studies to determine the ability to establish long penetration mode jets on a typical Mach 1.6 slender configuration, and study its impact on the boom signature. The results indicated that a jet with a longer penetration length was required to achieve any impact on the boom signature of a typical Mach 1.6 slender configuration. This paper focuses on an in-depth parametric study, done using the space-time conservation element solution element Navier-Stokes flow solver, for investigating the effect of various counterflowing jet conditions/configurations on two supersonic slender-body models (cone-cylinder and quartic body of revolution). The study is aimed at gaining a better understanding of the relationship between the shock penetration length and reduction of drag and boom signature for these two supersonic slender-body configurations. Different jet flow rates, Mach numbers, nozzle jet exit diameters and jet-to-base diameter ratios were examined. The results show the characteristics of a short-to-long-to-short penetration-mode pattern with the increase of jet mass flow rates, observed across various counterflowing jet nozzle configurations. Though the optimal shock penetration length for potential boom-signature mitigation is tied to the long penetration mode, it often results in a very unsteady flow and leads to large oscillations of surface pressure and drag. Furthermore, depending on the geometry of the slender body, longer jet penetration did not always result in maximum drag reduction. For the quartic geometry, the maximum drag reduction corresponds well to the longest shock penetration length, while this was not the case for the cone-cylinder-as the geometry was already optimized for drag. Numerical results and assessments obtained from this parametric study along with the recommendation for future implementation of counterflowing jets as a means for drag and noise reduction are detailed in this paper.

Venkatachari, Balaji Shankar↗
DOE OSTI2023

Benchtop assessment of sealing efficacy and breathability of additively manufactured (AM) face masks

The onset of the 2019 novel coronavirus disease (COVID-19) led to a shortage of personal protective equipment (PPE), medical devices, and other medical supplies causing many stakeholders and the general public alike to turn to additive manufacturing (AM) as a stopgap when normally accessible devices were not available. However, without a method to test these AM constructs, there continued to be a disconnect between AM suppliers and the community’s needs. The objective of this study was to characterize the pressure drop and leakage of four different publicly available AM face mask models with two filter material combinations, as well as to investigate the impact of frame modification techniques including the use of foam strips and hot-water face forming to improve fit when the masks are donned on manikin head forms. AM face mask frame designs were downloaded from public repositories during the early stages of the COVID-19 pandemic. AM face masks were fabricated and tested on manikin head forms within a custom chamber containing dry aerosolized NaCl. Pressure drops, particle penetration, and leakage were evaluated for various flow rates and NaCl concentrations. Results indicated that filter material combination and frame modification played a major role in the overall performance of the AM face masks studied. Filter material combinations showed improved performance when high filtration fabric was used, and the cross-sectional area of the fabric was increased. AM frame modifications appeared to improve AM face mask leakage performance by as much as 69.6%.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Technology progress and clean vehicle policies on fleet turnover and equity: insights from household vehicle fleet micro-simulations with $\text{ATLAS}$

This paper documents the design and application of ATLAS (Automobile and Technology Lifecycle-Based ASsignment), a comprehensive household vehicle transaction and technology adoption micro-simulator in the San Francisco Bay Area. ATLAS evolves the fleet mix of individual households by simulating the vehicle transaction and choice decisions in response to co-evolving demographics, land use, and vehicle technology simulations. While most existing literature has focused on the aggregate clean vehicle uptake, this paper differentiates distributional effects and decomposes the underlying mechanisms across heterogeneous sub-populations of households. Using scenarios and sensitivity simulations that vary vehicle technology and policy assumptions, we find that Zero Emission Vehicles (ZEVs) penetrate into higher income groups at a faster rate than into lower income groups, which is intuitive and aligns with expectations. Interestingly, the relative income disparity in ZEV ownership shrinks over time across all scenarios, with a ZEV mandate coupled with declining battery cost leading to the greatest reduction in disparity of ZEV ownership by 2050. Federal, state, and local financial incentives influence the redistribution of ZEV uptake across income groups and contribute to narrowing income disparity. Vehicle transaction frequency and new versus used market dynamics are found to be important factors contributing to the income disparity.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Impact of Testing Method on Safety Assessment of Aged Li-Ion Cells: Part II – Aged Cells Without Li Plating

Understanding the safety profile of aged Li-ion batteries is essential for developing effective battery management and hazard mitigation strategies. However, most safety assessments have focused on fresh batteries, with just a few calorimetry studies on aged batteries with metal oxide positive electrodes. This study provides a broad assessment of commercial 18650-type Li-ion batteries with NCA, NMC, and LFP positive electrodes, both uncycled and aged under conditions that promoted solid electrolyte interphase (SEI) growth as the dominant degradation mechanism. The cells underwent mechanical (nail penetration, crush), electrical (overcharge, overdischarge), and thermal (accelerating rate calorimetry) abuse tests. Safety was rated on general characteristics such as mass loss, maximum temperature, and EUCAR (European Council for Automotive R&D) hazard level, as well as characteristics specific to individual abuse tests. Generally, aged cells with SEI growth exhibited similar or improved safety compared to uncycled cells, contrasting with our previous findings on NCA cells with Li plating as the dominant aging mechanism (Part I of this series). Yet, some tests and characteristics indicated reduced aged cell safety, such as earlier triggering of mechanical failure. These results emphasize the need to examine aged battery safety across diverse empirical techniques, degradation modes, and chemistries.

Lithium-ion cells↗
NASA NTRS1980

Evaluation of a locally homogeneous flow model of spray combustion

A model of spray combustion which employs a second-order turbulence model was developed. The assumption of locally homogeneous flow is made, implying infinitely fast transport rates between the phase. Measurements to test the model were completed for a gaseous n-propane flame and an air atomized n-pentane spray flame, burning in stagnant air at atmospheric pressure. Profiles of mean velocity and temperature, as well as velocity fluctuations and Reynolds stress, were measured in the flames. The predictions for the gas flame were in excellent agreement with the measurements. The predictions for the spray were qualitatively correct, but effects of finite rate interphase transport were evident, resulting in a overstimation of the rate development of the flow. Predictions of spray penetration length at high pressures, including supercritical combustion conditions, were also completed for comparison with earlier measurements. Test conditions involved a pressure atomized n-pentane spray, burning in stagnant air at pressures of 3, 5, and 9 MPa. The comparison between predictions and measurements was fair. This is not a very sensitive test of the model, however, and further high pressure experimental and theoretical results are needed before a satisfactory assessment of the locally homogeneous flow approximation can be made.

Mao, C. P.↗
NASA NTRS1993

Variation of the energy release rate as a crack approaches and passes through an elastic inclusion

The variation of the energy release rate (ERP) at the tip of a crack penetrating an elastic inclusion is analyzed using an approach involving modeling the random array of microcracks or other defects by an elastic inclusion with effective elastic properties. Computations are carried out using a finite element procedure. The eight-noded isoparametric serendipity element with the shift of the midpoint to the quarter-point is used to simulate the singularity at the crack tip, and the crack growth is accommodated by implementing a mesh regeneration technique. The ERP values were calculated for various crack tip positions which simulate the process of the crack approaching and penetrating the inclusion.

Li, Rongshun↗