Search NASA⌕ Search

SEARCH · Search NASA

Results for “recrystallization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Surface recrystallization theory of the wear of copper in liquid methane

Copper was subjected to sliding against 440C in liquid methane. The normal load range was from 1/4 to 2 kilograms, and the sliding velocity range was from 3.1 to 25 meters per second. Over this range of experimental parameters, the wear rate of the copper rider was found to be proportional to the sliding velocity squared and to the normal load. Transmission electron microscopy was used to study the dislocation structure in the copper very near the wear scar surface. It was found that near the wear scar surface, the microstructure was characterized by a fine-cell recrystallized zone in which individual dislocations could be distinguished in the cell walls. The interiors of the cells, about 0.5 micrometer in diameter, were nearly dislocation free. Below the recrystallized layer was a zone that was intensely cold worked by the friction process. With increasing depth, this intensely cold worked zone gradually became indistinguishable from the partially cold worked bulk of the copper, representative of the initial condition of the material.

Bill, R. C.↗

The influence of gamma prime on the recrystallization of an oxide dispersion strengthened superalloy - MA 6000E

The requirement of large, recrystallized, highly elongated grains is of primary importance to the development of suitable high temperature properties in oxide dispersion strengthened-superalloys. In the present study the recrystallization behavior of MA 6000E, a recently developed Y2O3 strengthened superalloy produced by mechanical alloying, was examined using transmission and replication microscopy. Gradient and isothermal annealing treatments were applied to extruded and hot rolled products. It was found that conversion from a very fine (0.2 micron) grain structure to a coarse (approximately 10 mm) grain structure is controlled by the dissolution of the gamma prime phase, while grain shape was controlled primarily by the thermal gradient. The fine uniform oxide dispersion appeared to have only a secondary influence in determining the grain shape as columnar grains could be grown transverse to the working direction by appropriate application of the thermal gradient.

Hotzler, R. K.↗

Ultrasonic Determination Of Recrystallization

State of recrystallization identified. Measurement of ultrasonic attenuation shows promise as means of detecting recrystallization in metal. Technique applicable to real-time acoustic monitoring of thermomechanical treatments. Starting with work-hardened material, one ultrasonically determines effect of annealing, using correlation between ultrasonic attenuation and temperature.

Generazio, Edward R.↗

Effect of Recrystallization on Gas Bubble Swelling in UMo Fuels

Recrystallization plays an important role in swelling kinetics of irradiated metallic nuclear fuels. This talk will present a three-dimensional microstructure-dependent swelling model by integrating the evolution of intra-and inter- granular gas bubbles, dislocation loop density, and recrystallization.

Hu, Shenyang↗

In-situ observation of dynamic recrystallization in the bulk of zirconium alloy.

Dynamic recrystallization and related effects have been followed in situ and in real time while a metal undergoes rapid thermo-mechanical processing. Statistics and orientation correlations of embedded/bulk material grains were deduced from two-dimensional X-ray diffraction patterns and give deep insight into the formation of the microstructure. Applications are relevant in materials design, simulation, and in geological systems.

36 MATERIALS SCIENCE↗

Structural Damage and Recrystallization Response of Garnet Crystals to Intense Electronic Excitation

Here, the susceptibility to irradiation-induced damage, the fundamental mechanism of the relaxation kinetics, and the corresponding recrystallization effect related to the cation radius ratio are comprehensively investigated for Y 3 Al 5 O 12 and Gd 3 Ga 5 O 12 garnet crystals under 645 MeV Xe 35+ irradiation with different fluences of 5 × 10 11 –3 × 10 12 ions cm –2 . Regarding different lattice distortion and swelling levels, the observed microstructure transformations to disordered and amorphous phases, and corresponding hillock dimensions, consistently confirm that Gd 3 Ga 5 O 12 has a higher susceptibility to radiation damage than Y 3 Al 5 O 12 . Combined with iTS model calculations, although Y 3 Al 5 O 12 has higher atomic temperature and energy deposition than Gd 3 Ga 5 O 12 under the same ion velocity and electronic energy loss, the relatively high thermal conductivity and specific heat coefficient of Y 3 Al 5 O 12 crystals enhance the conduction and dissipation of deposition energy, and Gd 3 Ga 5 O 12 , with a higher cation-radius-ratio (r A /r B ), is more easily damaged to amorphous phase due to the less favorable kinetics of ordering and recovery of a melted track region to the crystalline phase. Additionally, the significant bandgap modification in spectral ranges of 5.88–6.75 eV for Y 3 Al 5 O 12 and 4.83–5.41 eV for Gd 3 Ga 5 O 12 , and the enhancement of defect-assisted-related luminescence are achieved, providing a basis to design novel optoelectronic devices in microelectronics fields.

36 MATERIALS SCIENCE↗

Suppression of Void Nucleation in High-Purity Aluminum via Dynamic Recrystallization

The process of ductile fracture in metals often begins with void nucleation at second-phase particles and inclusions. Previous studies of rupture in high-purity face-centered-cubic metals, primarily aluminum (Al), concluded that second-phase particles are necessary for cavitation. A recent study of tantalum (Ta), a body-centered-cubic metal, demonstrated that voids nucleate readily at deformation-induced dislocation boundaries. These same features form in Al during plastic deformation. This study investigates why void nucleation was not previously observed at dislocation boundaries in Al. Here, we demonstrate that void nucleation is impeded in Al by room-temperature dynamic recrystallization (DRX), which erases these boundaries before voids can nucleate at them. If dislocation cells reform after DRX and before specimen separation by necking, voids nucleation is observed. These results indicate that dislocation substructures likely plays an important role in ductile rupture.

36 MATERIALS SCIENCE↗

Dynamic Recrystallization Behavior of AISI 422 Stainless Steel During Hot Deformation Processes

In this work, hot compression tests were performed to investigate the dynamic recrystallization (DRX) process of a martensitic stainless steel (AISI 422) at temperatures of 950, 1000, 1050, 1100 and 1150 °C and strain rates of 0.01, 0.1 and 1 s{sup −1}. The dependency of strain-hardening rate on flow stress was used to estimate the critical stress for the onset of DRX. Accordingly, the critical stress to peak stress ratio was calculated as 0.84. Moreover, the effect of true strain was examined by fitting stress values to an Arrhenius type constitutive equation, and then considering material constants as a function of strain by using a third-order polynomial equation. Finally, two constitutive models were used to investigate the competency of the strain-dependent constitutive equations to predict the flow stress curves of the studied steel. It was concluded that one model offers better precision on the flow stress values after the peak stress, while the other model gives more accurate results before the peak stress.

36 MATERIALS SCIENCE↗

Evolution of Dynamic Recrystallization in 35CrMo Steel During Hot Deformation

To better understand the dynamic recrystallization (DRX) behavior of 35CrMo steel during hot deformation, a series of isothermal compression tests were carried out at different temperatures and strain rates. Using a constitutive equation built from the data obtained and the Arrhenius equation, the activation energy for hot deformation was determined through regression to be 342.69 kJ/mol. A model of the DRX kinetics was also constructed to characterize the influence of accumulated strain, temperature and strain rate on DRX evolution, which revealed that lower temperatures and higher strain rates require greater strain to achieve the same DRX volume fraction. Optical examination of the microstructure after deformation confirmed that this model accurately reflects reality and that grain size varies directly with deformation temperature, but inversely with strain rate.

36 MATERIALS SCIENCE↗

A New Method for Optimizing Hot Processing Parameters of Mg-6.0Zn-0.5Mn-0.5Er Alloy Based on Kinetic Model of Dynamic Recrystallization and Processing Map

Hot deformation behavior of the cast-homogenized Mg-6.0Zn-0.5Mn-0.5Er alloy was studied using dynamic recrystallization (DRX) kinetic model and processing map. The compressing tests were conducted in the temperature range of 250-450 °C and strain rates of 0.001-1 s{sup −1}. According to the evolution of microstructures, under lower strain rates, the main DRX mechanism of Mg-6.0Zn-0.5Mn-0.5Er alloy is continuous DRX (CDRX); twinning induced DRX (TDRX) and CDRX both become the main DRX mechanism under higher strain rates. The DRX kinetics model of Mg-6.0Zn-0.5Mn-0.5Er alloy is calculated as X{sub DRX}=1−exp[−1.9463(((ε−ε{sub c})/(ε{sup ∗}))){sup 1.4608}], which is corresponding to the microstructure evolutions of DRX under different deformation conditions. The contour map of DRX was proposed based on the calculation results of DRX kinetics model. The processing maps are constructed to predict processing parameters of the alloy, and the predictability was evaluated combining with the contour map of DRX and dynamic materials model (DMM) processing map. It is deduced from the microstructures evolution and processing map that the optimum processing domain is mainly at 380-450 °C and 0.01-0.001 s{sup −1}, and 410-420 °C and 0.01-1 s{sup −1}.

36 MATERIALS SCIENCE↗

Recrystallization Behavior and Super-Elasticity of a Metastable β-Type Ti-21Nb-7Mo-4Sn Alloy During Cold Rolling and Annealing

Based on the d-electron alloy design theory, a new metastable β-type titanium alloy for biomedical applications, Ti-21Nb-7Mo-4Sn (wt.%) was designed in this article. This theory predicted this alloy was a metastable single β-type titanium alloy with low elastic modulus at room temperature, and the β-phase transition (β to α″) would be easy to occur during the cold rolling. The evolution of microstructure and mechanical properties of this alloy during cold rolling plus annealing were investigated by means of x-ray diffraction, optical microscope, transmission electron microscope and mechanical properties test. The results indicate that only β phase can be identified in this alloy before cold rolling, while a large amount of lath martensite (α″ phase) appears after cold rolling due to stress-induced martensitic transformation, which is in accordance with the prediction of the d-electron alloy design theory. The recrystallization nucleation occurs preferentially in the martensite lath region during the subsequent annealing process, and this region forms a large number of nano-crystals and microcrystals, showing that cold rolling plus annealing can become a new process for refining grains. Compared with casting and cold rolling samples, the annealing materials at 923 K for 10 min have excellent comprehensive mechanical properties with lower elastic modulus (58 GPa) and higher elastic recovery rate (35.39%).

36 MATERIALS SCIENCE↗

Exploiting Acoustic Anisotropy to Detect Recrystallization in a Ni Single Crystal Using Ultrasonic Nondestructive Inspection

Ultrasonic inspection was used to detect regions of recrystallization (RX) within a single crystal of Ni. RX can produce polycrystalline regions within single-crystal (SX) materials. Because RX regions act as initiator sites for failure by fatigue-crack growth in otherwise SX Ni-based superalloys, RX is an issue of direct concern for the service life of high-performance turbine blades. Detection and discrimination of RX regions in single-crystal materials are significant challenges for current nondestructive inspection technologies. The present study leverages the elastic anisotropy of single crystals, which produces acoustic anisotropy, to ultrasonically detect and characterize RX regions produced within single-crystal specimens. Single crystals of pure Ni were processed to create controlled regions of RX. These specimens were ultrasonically examined in an immersion tank using a high-resolution, polyvinylidene fluoride transducer to detect acoustic impedance changes across the boundaries between different crystals (i.e., grains) within the RX region. Data from time-of-flight and absolute peak amplitude measurements were used to create acoustic images that were compared against electron microscope images of the RX regions. The ultrasonic inspection technique described here successfully detected not only the locations of RX regions, but also the approximate sizes and shapes of the RX regions.

36 MATERIALS SCIENCE↗

Development of a heterogeneous nanostructure through abnormal recrystallization of a nanotwinned Ni superalloy

This work explores the development of a heterogeneous nanostructured material through leveraging abnormal recrystallization, which is a prominent phenomenon in coarse-grained Ni-based superalloys. Additionally, through synthesis of a sputtered Inconel 725 film with a heterogeneous distribution of stored energy and subsequent aging treatments at 730°C, a unique combination of grain sizes and morphologies was observed throughout the thickness of the material. Three distinct domains are formed in the aged microstructure, where abnormally large grains are observed in-between a nanocrystalline and a nanotwinned region. In order to investigate the transitions towards a heterogeneous structure, crystallographic orientation and elemental mapping at interval aging times up to 8 h revealed the microstructural evolution and precipitation behavior. From the experimental observations and the detailed analysis of this study, the current methodology can be utilized to further expand the design space of current heterogeneous nanostructured materials.

36 MATERIALS SCIENCE↗

Assessment of metadynamic recrystallization in single copper particle impacts by focused ion beam tomography

We study single Cu-on-Cu impacts relevant to cold spray deposition and quantitatively analyze the metadynamic recrystallization (mDRX) that takes place after the impact by virtue of lingering impact adiabatic heat. Unlike prior studies, the current full 3D tomographic analysis of the mDRX volume shows that mDRX is extremely common in such impacts, although it is often missed when examining 2D sections. We also report an unexpected trend: there is a “sour spot” for mDRX at velocities about 20–40 % above the velocity for particle adhesion. This non-monotonic trend is contrary to the expectations based on increasing adiabatic heating with velocity. With a schematic model, we show that the trend can be explained on the basis of heat transfer: cooling of the heat-affected region is limited by transport through the bonded regions at the particle-substrate interface. Thus, bonding has a prominent role in the heat dissipation process and the best bonded particles most rapidly bulk quench, avoiding mDRX. Here, the developed semi-empirical model aligns with the experimental findings and may help inform microstructural evolution during cold spray and post-spray processing.

FIB-SEM tomography↗

Modeling discontinuous dynamic recrystallization containing second phase particles in magnesium alloys utilizing phase field method

Pre-existing second phase particles can induce particle stimulated nucleation (PSN) and pinning effect on grain boundaries during DRX process of magnesium alloys. The interaction among pinning effect, PSN mechanism and strain-induced grain boundary migration (SIBM) nucleation mechanism imposes challenge in quantitative study of microstructure evolution. A phase field model that describes discontinuous dynamic recrystallization process considering second phase particles (PF-DDRX-SP) which mainly distribute along grain boundaries is developed. The second phase order parameter with diffusion interface is introduced to the free energy function. With considering the pinning effect of second phase particles on grain boundaries, the grain boundary energy couples the interaction between second phase and grains. The effect of second phase on dislocation density evolution is considered in the model, and the PSN and SIBM mechanism are both executed by limiting the nucleation position to the grain boundary and the second phase interface. For the validation, the initial topology consistent with initial microstructure is applied to the simulation of DRX kinetics and flow behavior of AZ80 magnesium alloy, and great reliability and accuracy of developed model is indicated. Furthermore, through the model, the microstructure evolution with different particle size and with different volume fraction of round particle during DRX process were simulated. Finally, the results show that particles with higher dispersion reduce the number of DRX nuclei, which indicate that second phase particles suppress the nucleation at grain boundaries because of the pinning effect. More importantly, the proposed model could also quantitatively predict the relationships between the parameters of second phase particles and DRX behaviors, and enable to optimize the initial second phase structure in a uniform grain structure during thermomechanical process.

36 MATERIALS SCIENCE↗

Strain localization and dynamic recrystallization in polycrystalline metals: Thermodynamic theory and simulation framework

We describe a theoretical and computational framework for adiabatic shear banding (ASB) and dynamic recrystallization (DRX) in polycrystalline materials. The Langer-Bouchbinder-Lookman (LBL) thermodynamic theory of polycrystalline plasticity, which we recently reformulated to describe DRX via the inclusion of the grain boundary density or the grain size as an internal state variable, provides a convenient and self-consistent way to represent the viscoplastic and thermal behavior of the material, with minimal ad-hoc assumptions regarding the initiation of yielding or onset of shear banding. Here, we implement the LBL-DRX theory in conjunction with a finite-element computational framework. Favorable comparison to experimental measurements on a top-hat AISI 316L stainless steel sample compressed with a split-Hopkinson pressure bar suggests the accuracy and usefulness of the LBL-DRX framework, and demonstrates the crucial role of DRX in strain localization.

36 MATERIALS SCIENCE↗

A new micromechanics based full field numerical framework to simulate the effects of dynamic recrystallization on the formability of HCP metals

This work presents a new full-field, efficient and mesh-free numerical framework to model microstructure evolution, dynamic recrystallization (DRX) and formability in hexagonal closed-packed (HCP) metals such as magnesium alloys at warm temperatures. A rate tangent-fast Fourier transform-based elasto-viscoplastic crystal plasticity constitutive model for HCP metals (RTCP-FFT-HCP) is coupled with a probabilistic cellular automata (CA) approach to model DRX (CA-DRX). Furthermore, this new model is coupled with the Marciniak-Kuczynski (M-K) approach to model formability of magnesium alloys at elevated temperatures. The RTCP-FFT-HCP model computes macro stress-strain, twinning volume fraction, micromechanical fields, texture evolution and local dislocation density. Nucleation of new grains and their subsequent growth is modeled using the cellular automata approach with probabilistic state switching rule. First, the proposed RTCP-FFT-HCP model is validated by comparing the predicted stress-strain responses and texture evolution under uniaxial tension and compression with experimental measurements for AZ31 sheet alloy at room temperature. The coupled CA-RTCPFFT-HCP model is further validated by comparing the predicted stress-strain responses and texture evolution in uniaxial compression with experimental measurements at 100 °C, 200 °C and 300 °C for the AZ31 sheet alloy. Next, the forming limit diagrams (FLDs) with and without including the effects of DRX are simulated at 100 °C, 200 °C and 300 °C for AZ31 sheet alloy. The predicted FLDs with DRX show very good agreement with the experimental measurements and clearly demonstrate the need for an accurate DRX model. The study reveals that the DRX strongly affects the deformed grain structure, grain size and texture evolution and also highlights the importance accounting for DRX during FLD simulations at high temperatures.

36 MATERIALS SCIENCE↗

Heterogenous activation of dynamic recrystallization and twinning during friction stir processing of a Cu-4Nb alloy

An interplay between high degree of shear deformation and deformation-induced heating occurs during friction stir processing (FSP) of metals. In medium-to-low stacking fault energy Cu alloys, this can lead to a complex spatially heterogenous activation of dynamic recrystallization (DRX) and twinning mechanisms. Within the Cu-Nb system, the presence of Nb is further expected to influence the DRX mechanism of the Cu matrix. However, the microstructural changes induced by the co-deformation of Nb during FSP are still not well understood. So, this study uses a combination of multimodal microstructural characterization, solution thermodynamics-based predictions, and computational crystal plasticity simulation to reveal the various microstructural evolution mechanisms that can occur during FSP of a Cu-4at.%Nb binary model alloy. The formation of softer DRX zones, and harder shear localization regions are revealed using electron backscatter diffraction, transmission electron microscopy, atom probe tomography, and crystal plasticity modeling.

36 MATERIALS SCIENCE↗