Search NASA⌕ Search

SEARCH · Search NASA

Results for “reference system”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

FY24 Report on Water NSTF Testing: Lower Tank Inlet Piping Configuration

The following report serves as a summary of the accomplishments and testing results by the Natural convection Shutdown heat removal Test Facility (NSTF) experimental program over the past 12-month period. A major activity included reconfiguration of the chimney piping geometry which altered the discharge position into the tank from the original 50% tank height to a new lower position at a 10.9% tank height. This modification increases the volume of available coolant thus extending long-term operating capacity, however also results in a decreased liquid driving head which has the potential to reduce the natural circulation efficiency and decrease overall performance. Examination of the tradeoffs for these two configurations is an area of interest for RCCS designers and drove planned test activities this year. Ten matrix tests were performed in FY24, totaling 195 hours of heated operations and 12.9 MWh of electrical heating throughout the year, with eight classified as Accepted per NQA-1 and two classified as Trending. Testing prior to the facility reconfiguration examined the facility response to throttling at the tank inlet, demonstrating increased sensitivity of flow instabilities to throttling within the two-phase region when compared to throttling at the lower sensitivity single-phase inlet region. Testing after the chimney reconfiguration began with a baseline test at conditions of 80% inventory fill and prototypic thermal power input of 2.1 MW t . In addition to establishing a reference for nominal system behavior and performance, repeat testing with multiple subsequent runs demonstrated strong repeatability between tests performed at the same conditions in this new configuration. These tests also examined if influences would occur to system behavior with installation of new higher-resolution instrumentation within the upper chimney. In this critical region where boiling and flashing phenomena dominate, the test results provided confidence that the new instrumentation does not uncharacteristically influence the observed behaviors. An inventory parametric series was then initiated to examine system behavior with the new chimney configuration at six varying initial inventory levels, ranging from high 80% to low 20% fill. Two-phase oscillations with similar peak and mean flow rates were observed when comparing to the previous mid tank configuration. Generally, similar system response trends with inventory were also observed, such as two phase oscillations suppressing as inventories were lowered. However, in one absolute inventory comparison at the highest fill of 80%, flow oscillations saw a gradual growth over the 4 hours of two-phase operation in the new lower tank inlet configuration, opposite of the gradual dampening observed in the mid tank inlet configuration. This can be attributed to, in part, a greater hydrostatic head pressure above the two-phase discharge region where the boiling front is developed. Furthermore, the change resulted in greater sensitivity to liquid degassing phenomena during single-phase heating, causing loop instabilities to form which trigged moderate flow degradation during the period approaching saturation and boiling conditions. This behavior had been observed previously under some conditions but was a common occurrence in recent testing with the newer lower tank inlet configuration. Initial observations from these first data sets suggest an overall larger window of stability for the mid tank inlet configuration compared to the lower tank inlet. Lastly, the lowest inventory fill test was repeated over an extended testing window to examine depletion behavior. Natural circulation flow and effective heat removal performance were observed during most of the testing period; only after the tank became fully drained (0% fill) did flow stagnate and violent geysering events occur. This early observation confirms one relative advantage over the mid tank inlet configuration, which stagnated under comparable conditions at ~20% inventory remaining in the tank.

42 ENGINEERING↗
DOE OSTI2025

Manipulation of Geographic Information in Global Seismology

Geographic data, such as seismic event locations, station locations, etc., are generally given in geographic latitude Φ ’, longitude θ , and depth below sea level, ζ , using the WGS84 ellipsoid as a reference. In software systems that use this type of geographic data, it is necessary to manipulate the data mathematically in order to perform such tasks as finding the angular distance or azimuth from one point to another, to find an array of points along a great circle, to rotate a point about a pole of rotation, to move a point some angular distance in a specified direction, to find the intersections of two great circles or to find the intersections of a great circle and a small circle. In this paper, equations are presented that convert geographic locations first to geocentric coordinates and then to Earth-centered Cartesian coordinates where many mathematical manipulations can be performed conveniently and efficiently.

58 GEOSCIENCES↗
DOE OSTI2022

Effects of Mechanical Recycling on Carbon Fiber-Based Hybrid Composites

Carbon fiber (CF) reinforced composites are high-performing, highly utilized material systems historically used in aerospace. As the cost of CF decreases, other industries, such as automotive and energy generation, seek to adopt CF composites into their applications. A sudden increase in CF demand may create supply chain issues if the adoption happens without scaling up of the CF production. A solution for reducing the reliance on CF is to substitute some portion of the CF content with another fiber type without significantly reducing the material properties. When multiple reinforcing fillers are introduced into a composite system, the materials system is often referred to as a hybrid composite and in this case a CF-based hybrid composite. To further relieve reliance on CF and with sustainable manufacturing becoming more prominent in industry, mechanical recycling can be employed to replace all or a percentage of the virgin material content. Utilizing recycled content in place of virgin content will further aid in reducing the reliance on virgin CF and decrease overall material costs. Here, the effects of utilizing mechanically recycled feedstocks on the mechanical properties of injection molded samples are explored to understand the feasibility of re-manufacturing recycled CF-based hybrid composites. By determining the mechanical properties and mechanisms in which the properties change through varying recycled content, the assessment of how the material will perform in other manufacturing processes can be inferred. As a result, industry will gain better insight into utilizing mechanically recycled feedstocks to reduce their reliance on the CF supply chain.

36 MATERIALS SCIENCE↗
DOE OSTI2022

CLM5 CAMELS Basins Ensemble

Land surface models such as Community Land Model Version 5 (CLM5) are essential tools for simulating the behaviors of the terrestrial system. Despite the extensive application of CLM5, limited attention has been paid to the underlying uncertainties associated with its hydrologic parameters and the implications that these uncertainties have on water resources applications. To address this long-standing issue, we conduct a comprehensive hydrologic parameter uncertainty characterization (UC) of CLM5 over the hydroclimatic gradients of the Conterminous United States using five meteorological datasets. Key datasets produced from the UC experiment include a benchmark dataset of CLM5 default hydrological performance, parameter sensitivity identified for 28 hydrological metrics, and large ensemble outputs for hydrological predictions. The presented datasets can assist CLM5 calibration and to support broad applications such as evaluating vulnerabilities to droughts and floods. The dataset can be used to identify under what hydroclimate conditions parametric uncertainties demonstrate substantial effects on hydrological predictions and clarify where further investigations are needed to understand how land runoff uncertainties interact with other Earth system processes. Please refer to the included README.pdf for a description of the included files. Note that raw CLM5 model outputs for each forcing dataset are hosted on a Globus endpoint: https://app.globus.org/file-manager?destination_id=d22ef858-27b0-11ed-a910-fd3165076336.

Yan, Hongxiang↗
DOE OSTI2023

CLM5 CAMELS Basins Ensemble

Land surface models such as Community Land Model Version 5 (CLM5) are essential tools for simulating the behaviors of the terrestrial system. Despite the extensive application of CLM5, limited attention has been paid to the underlying uncertainties associated with its hydrologic parameters and the implications that these uncertainties have on water resources applications. To address this long-standing issue, we conduct a comprehensive hydrologic parameter uncertainty characterization (UC) of CLM5 over the hydroclimatic gradients of the Conterminous United States using five meteorological datasets. Key datasets produced from the UC experiment include a benchmark dataset of CLM5 default hydrological performance, parameter sensitivity identified for 28 hydrological metrics, and large ensemble outputs for hydrological predictions. The presented datasets can assist CLM5 calibration and to support broad applications such as evaluating vulnerabilities to droughts and floods. The dataset can be used to identify under what hydroclimate conditions parametric uncertainties demonstrate substantial effects on hydrological predictions and clarify where further investigations are needed to understand how land runoff uncertainties interact with other Earth system processes. Please refer to the README.pdf for a description of the included files. Note that raw CLM5 model outputs for each forcing dataset are hosted on a Globus endpoint: https://app.globus.org/file-manager?destination_id=d22ef858-27b0-11ed-a910-fd3165076336.

Yan, Hongxiang↗
DOE OSTI2020

Beam controlled nano-robotic device

A system and method (referred to as a method) to fabricate nanorobots. The method generates a pixel map of an atomic object and identifies portions of the atomic object that form a nanorobot. The method stores those identifications in a memory. The method adjusts an electron beam to a noninvasive operating level and images the portions of the atomic object that form the nanorobot. The method executes a plurality of scanning profiles by the electron beam to form the nanorobot and detects nanorobot characteristics and their surroundings via the electron beam in response to executing the plurality of scanning profiles.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Equitable Access to Community Solar: Program Design and Subscription Considerations

Over 2.7 GWac community solar has been installed in the U.S. as of 2020, and 44% (1.2 GWac ) were installed after 2018, which indicates a fast-growing segment of the solar market .Community solar refers to a system that allows customers to subscribe part of a solar PV system and receive credit on their electricity bills based on power production. Although the growth of community solar market makes accessing solar energy easier, low and moderate income (LMI) potential subscribers may still face challenges, such as no or low credit scores.To investigate the program designs and subscription considerations for LMI customers, we provide a summary of existing state-level low-income community solar policies, as well as estimated LMI capacity and subscribers in the U.S.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2022

An improved synthetic signal injection routine for HAYSTAC

Microwave cavity haloscopes are among the most sensitive direct detection experiments searching for dark matter axions via their coupling to photons. When the power of the expected microwave signal due to axion-photon conversion is on the order of 10-24 W, having the ability to validate the detector response and analysis procedure by injecting realistic synthetic axion signals becomes helpful. Here we present a method based on frequency hopping spread spectrum for synthesizing axion signals in a microwave cavity haloscope experiment. It allows us to generate a narrow and asymmetric shape in frequency space that mimics an axion's spectral distribution, which is derived from a Maxwell-Boltzmann distribution. In addition, we show that the synthetic axion's power can be calibrated with reference to the system noise. Compared to the synthetic axion injection in HAYSTAC phase I, we demonstrated synthetic signal injection with a more realistic lineshape and calibrated power.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Direct analysis of cotton swipes for uranium and plutonium isotopic determination by microextraction-ICP-MS

The determination of uranium and plutonium isotopic abundance on environmental samples collected by International Atomic Energy Agency (IAEA) inspectors is vital for the detection of undeclared nuclear activities and material under the international nuclear safeguards regime. Current analytical protocols require time-consuming sample preparation steps prior to subsequent measurement by inorganic mass spectrometry (MS). Recent efforts from this laboratory have focused on developing sample preparation methods for faster analysis, potentially allowing higher sample throughput[1]. Alternative methods including microextraction sampling in conjunction with inductively coupled plasma-mass spectrometry (ICP-MS) have been recently explored. This methodology, microextraction-ICP-MS, was developed such that uranium and plutonium could be extracted from the swipe surface and directed into the ICP-MS for an in-situ measurement, eliminating the need for swipe ashing and digestion. A commercial off-the-shelf microextraction system was customized with an automated movable XY stage that can be programmed to save sampling locations, allowing for automated rapid sampling of swipe surfaces. Additional efforts have focused on the utilization of collision cell technology to the microextraction ICP-MS method. This would eliminate the need for lengthy column chemistry procedures to purify separated uranium and plutonium fractions before analysis. Here, the extracted U/Pu analyte is measured by reacting the uranium ions with CO2 in the collision cell of an ICP-MS, shifting the uranium to UO+, which will not interfere with the plutonium isotopic determination. The developed method utilizing collision cell – ICP-MS technology has demonstrated the ability to measure plutonium isotope ratios in the presence of high uranium concentration on the transient signal from the microextraction system utilizing certified reference materials from JRC-Geel and the New Brunswick Laboratory Program Office.

Bradley, Veronica↗
DOE OSTI2021

Maximum Power Reference Tracking Algorithm for Power Curtailment of Photovoltaic Systems

This paper presents an algorithm for power curtailment of photovoltaic (PV) systems under fast solar irradiance intermittency. Based on the Perturb and Observe (P&O) technique, the method contains an adaptive gain that is compensated in real-time to account for moments of lower power availability. In addition, an accumulator is added to the calculation of the step size to reduce the overshoot caused by large irradiance swings. A testbed of a three-phase single-stage, 500 kVA PV system is developed on the OPAL-RT eMEGAsim real-time simulator. Field irradiance data and a regulation signal from PJM (RTO) are used to compare the performance of the proposed method with other techniques found in the literature. Results indicate an operation with smaller overshoot, less dc-link voltage oscillations, and improved power reference tracking capability.

Paduani, Victor↗
DOE OSTI2025

The approximate second order coupled-cluster method based on a size-consistent Brillouin–Wigner partitioning

We present a variant of the approximate second order coupled-cluster method (CC2) with a two-parameter size-consistent Brillouin–Wigner (BW-s) partitioning instead of a Møller–Plesset (MP) partitioning for the unperturbed Hamiltonian, which we refer to as BWs-CC2. The computational complexity of this model scales identically to CC2 with molecular size. Conventional CC2 and its regularized BWs-CC2 variants, as well as conventional MP2 and two of its regularized BW-s2 variants, were assessed on a 535 element database spanning thermochemistry, non-covalent interactions, barrier heights, and isomerization energies. To ensure a well-defined model chemistry, the assessment was performed using internally stable spin-polarized Hartree–Fock (HF) orbitals in the finite aug-cc-pVQZ basis without counterpoise corrections. As a result of using stable orbitals, contrary to conventional wisdom, we find that CC2 substantially outperforms MP2 on molecules with significantly spin contaminated reference orbitals without a significant increase in error on systems with a spin-pure reference, showing the value of its single substitutions. While no single choice of regularization parameters can be optimal for all datasets, we find that BWs-CC2 generally outperforms both CC2 and BW-s2 with a single judicious parameter choice. Additional tests on dipole moments and bond lengths of diatomics provide further support for the utility of this choice. Furthermore, the main outliers and poorest performing cases are associated with large amounts of spin-contamination in the HF reference, which is indicative of systems with either strong correlation or extensive artificial symmetry breaking. Overall, these findings argue that the perception of the quality of the CC2 ground state should be reevaluated and that it can be further improved upon by the soundly based BWs-CC2 variant with the recommended parameter choice.

Correlation energy↗
DOE OSTI2021

Measurement-induced purification in large- N hybrid Brownian circuits

Competition between unitary dynamics that scrambles quantum information nonlocally and local measurements that probe and collapse the quantum state can result in a measurement-induced entanglement phase transition. Here we study this phenomenon in an analytically tractable all-to-all Brownian hybrid circuit model composed of qubits. The system is initially entangled with an equal sized reference, and the subsequent hybrid system dynamics either partially preserves or totally destroys this entanglement depending on the measurement rate. Our approach can access a variety of entropic observables which are distinguished by the averaging procedure, and for concreteness we focus on a particular purity quantity for which the averaging is particularly simple. We represent the purity as a path integral coupling four replicas with twisted boundary conditions. Saddle-point analysis reveals a second-order phase transition corresponding to replica permutation symmetry breaking below a critical measurement rate. The transition is mean-field-like and we characterize the critical properties near the transition in terms of a simple Ising field theory in 0 + 1 dimensions. In addition to studying the purity of the entire system, we study subsystem purities and relate these results to manifestations of quantum error correction in the model. Here, we also comment on the experimental feasibility for simulating this averaged purity, and corroborate our results with exact diagonalization for modest system sizes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

An electrified boom actuation system with energy regeneration capability driven by a novel electro-hydraulic unit

This paper presents a novel electrified solution for linear actuation systems, which has undergone a successful in-vehicle demonstration, marking a significant advancement in this field. Aligned with the growing trend towards electrification, this solution holds promise for a wide range of off-road applications. The showcased electrohydraulic actuation architecture enables efficient four-quadrant operation and incorporates energy recovery capabilities. At the core of the system lies a distinctive electro-hydraulic unit, integrating a fixed hydraulic pump and a variable-speed electric motor into a compact and powerful entity. A specialized hydraulic system is designed to efficiently transform electrical energy from the electro-hydraulic unit into boom cylinder actuation. The sizing of the system is determined by the boom operation of a commercial compact loader. The maximum power output of the electro-hydraulic system is approximately 15 kW. The components of the proposed system are integrated into the reference vehicle, and comprehensive performance tests are conducted. The results of the tests performed on the vehicle with the boom lifting and lowering cycle indicate an overall system efficiency of 60%. The electrified solution consumes only about one-third of the energy used by the conventional boom actuation system on the reference machine, while exhibiting energy savings exceeding 75% during specific work phases. The energy savings come mainly from energy regeneration and minimal loss from throttling through the specialized hydraulic circuit design. Finally, the successful demonstration on the reference vehicle underscores the practicality and effectiveness of the proposed electrified solution in current mobile hydraulic applications

42 ENGINEERING↗
DOE OSTI2022

A Procedure to Correct the Historical Atmospheric Longwave Irradiance Data When the World Reference Is Established with Respect to the International System of Units

Historical and traceable atmospheric longwave irradiance data sets with traceability to the International System of units (SI) are essential for renewable energy and atmospheric science research and applications. To date, all pyrgeometers used to measure the irradiance are traceable to the interim World InfraRed Standard Group (WISG) not to SI units. In 2013 the Absolute Cavity Pyrgeometer (ACP), [Reda et al., 2012] was developed at the National Renewable Energy Laboratory (NREL) to measure the atmospheric longwave irradiance. The ACP has been compared against the InfraRed Integrating Sphere (IRIS) developed by the Physikalisch-Meteorologisches Observatorium Davos/World Radiation Center (PMOD/WRC) [J. Grobner, 2012]. ACP and IRIS are absolute instruments traceable to SI units through the International Temperature Scale ITS-90. Results of six comparisons between ACP and IRIS at different location have shown that the irradiance measured by WISG pyrgeometers is underestimating clear-sky atmospheric longwave irradiance by 2 to 6 W/m 2 [Grobner et al., 2014]. Therefore, once the world reference is established with traceability to SI units the WISG would be corrected then used to calibrate field pyrgeometers with traceability to SI units. The described method below is used to correct the historical atmospheric longwave irradiance data sets in anticipation of the WISG scale change.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

A Procedure to Correct the Historical Atmospheric Longwave Irradiance Data When the World Reference Is Established with Respect to the International System of Units

Historical atmospheric longwave irradiance data sets with traceability to the International System of Units (SI) are essential for renewable energy and atmospheric science research and applications. To date, all pyrgeometers used to measure the irradiance are traceable to the interim World Infrared Standard Group (WISG), not to SI units. In 2013, the Absolute Cavity Pyrgeometer (ACP) (Reda et al. 2012) was developed at the National Renewable Energy Laboratory (NREL) to measure the atmospheric longwave irradiance. The ACP has been compared against the InfraRed Integrating Sphere (IRIS), developed by the Physikalisch-Meteorologisches Observatorium Davos/World Radiation Center (PMOD/WRC) (Grobner 2012). The ACP and the IRIS are absolute instruments traceable to SI units through the International Temperature Scale of 1990. Results of six comparisons between the ACP and the IRIS at different locations have shown that the irradiance measured by WISG pyrgeometers underestimates clear-sky atmospheric longwave irradiance by 2 W/m 2 to 6 W/m 2 (Grobner et al. 2014); therefore, once the world reference is established with traceability to SI units, the WISG would be corrected, then used to calibrate field pyrgeometers with traceability to SI units. The following described method is used to correct the historical atmospheric longwave irradiance data sets in anticipation of the WISG scale change.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

A Procedure to Correct the Historical Atmospheric Longwave Irradiance Data When the World Reference Is Established with Respect to the International System of Units

Historical atmospheric longwave irradiance data sets with traceability to the International System of Units (SI) are essential for renewable energy and atmospheric science research and applications. To date, all pyrgeometers used to measure the irradiance are traceable to the interim World Infrared Standard Group (WISG), not to SI units. In 2013, the Absolute Cavity Pyrgeometer (ACP) (Reda et al. 2012) was developed at the National Renewable Energy Laboratory (NREL) to measure the atmospheric longwave irradiance. The ACP has been compared against the InfraRed Integrating Sphere (IRIS), developed by the Physikalisch-Meteorologisches Observatorium Davos/World Radiation Center (PMOD/WRC) (Gröbner 2012). The ACP and the IRIS are absolute instruments traceable to SI units through the International Temperature Scale of 1990. Results of six comparisons between the ACP and the IRIS at different locations have shown that the irradiance measured by WISG pyrgeometers underestimates clear-sky atmospheric longwave irradiance by 2 W/m 2 to 6 W/m 2 (Gröbner et al. 2014); therefore, once the world reference is established with traceability to SI units, the WISG would be corrected, then used to calibrate field pyrgeometers with traceability to SI units. The following described method is used to correct the historical atmospheric longwave irradiance data sets in anticipation of the WISG scale change.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Reference Piping and Instrumentation Diagrams for Heat Transport Systems for Methanol Plants

This report aims to bridge the gap between advanced nuclear reactor vendors and methanol producers seeking decarbonization. It equips both parties with tools and preliminary information for integrating clean heat from advanced reactors into novel methanol production processes. The proposed investigation in this report involves a three-step approach: 1. Design of Current and Decarbonized Process Models for Methanol Production. This report initiates process modeling of two novel methanol production pathways, with their overall energy requirements comparative to classical methanol production (see Figure ES1). The two process models provide the foundation for analyzing integration of hermos-electric generation from advanced nuclear reactors. 2. Identification of Coupling Points to Integrate Advanced Reactors. This report investigates the integration with two advanced reactor technologies: light-water reactors (LWRs) and high-temperature gas reactors (HTGRs). The key coupling points between advanced nuclear reactors and the production facilities associated with the two decarbonized methanol process pathways are identified. 3. Preliminary Heat and Electricity Transfer Design from Reactors to Methanol Production Sites. The preliminary designs for piping and instrumentation to transfer heat from the boundary of advanced reactor technology location to the boundary of methanol production site are evaluated within the context of decarbonized pathways. The pipe analysis for heat transfer adheres to relevant codes and specifications from American Society of Mechanical Engineering. A simplified design for transmission of electricity to the industrial site has been provided.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Microbial sensor system for monitoring and imaging of an environment

A microbial sensor, microbial sensing system, and method that can be used to determine the chemical environment of unsaturated soils, rhizosphere, and/or plants are disclosed. The microbial sensing system can be used for monitoring the health of plants including nutrients, salinity, contaminants, chemicals (pesticides, herbicides) and diseases. A microbial sensing system can include one or more indicator electrodes and a reference electrode. The microbial sensing system can include a signal acquisition and/or communication module to allow the real-time collection of data from field deployments and laboratory investigations.

Burge, Scott R.↗