Search NASA⌕ Search

SEARCH · Search NASA

Results for “rf”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Cr plasma-material-interaction in PISCES-RF: D thermal release, retention, and erosion

Pure chromium (Cr) targets were exposed to high-flux deuterium (D) plasmas in the Pisces-RF linear plasma device, and measurements of D retention, release, and erosion were subsequently performed. Post-exposure D retention was quantified using temperature-programmed desorption on Cr targets irradiated by 50 eV ions over a broad range of exposure temperatures (423–873 K) and ion fluences (3 × 10 24 – 3 × 10 26 m −2 ). The retained D inventory was observed to decrease rapidly with increased exposure temperature, from approximately ∼7 × 10 20 m −2 at ∼ 420 K, to then saturate near ∼ 10 20 m −2 for exposure temperatures above ∼550 K. Separately, at fixed exposure temperature (∼450 K), D retention was found to have only a weak dependence on increasing ion fluence. Lastly, the erosion of Cr in D plasma was investigated for ion impact energies in the range 40 ≤ E i ≤ 250 eV. Erosion was inferred using optical emission spectroscopy (OES) from the ratio of emission lines (Cr I (425.4 nm)/D I (656.1 nm)) measured close to the target. Conversion of the OES yield data to net erosion yield was made with singular ion energy target mass-loss measurements. These net erosion yield data were then further corrected to obtain gross erosion yield by accounting for a re-deposition factor, computed using a simple model. The gross erosion yield is found to be 2–4 times lower than predicted by SDTrimSP, consistent with that typically observed for light-ion sputtering under high-flux plasma conditions.

Chromium↗
DOE OSTI2026

Decomposition of methane diluted with inert gas in an RF discharge cell

Decomposition of methane using non-thermal plasmas is an attractive route for producing hydrogen-rich gases and valuable carbon nanomaterials. Understanding how plasma discharge modes influence methane decomposition in optimizing plasma-assisted chemical conversion remains unexplored. This study explores the coupling between the discharge structure and product selectivity in RF capacitively coupled discharges operating in methane/inert gas mixtures in the pressure range of 2–3 torr. Under our experimental conditions the discharge exhibits mode transitions from uniform to striated in Ar and Kr and from diffuse to contracted in Ar and Kr with <5% CH 4 . The discharges in He and Ne remained uniform under our operating conditions, and their mixtures with CH 4 remained diffuse. A 0-d model for Ar/CH 4 discharge established a threshold for contraction while also asserting the importance of Ar$^{*}_{\textrm{m}}$ in the dissociation and ionization processes. The highest degree of methane decomposition, >99.7% with the main products of acetylene and graphitized solid carbon was achieved in the contracted discharge mode for both Kr or Ar with ⩽5% CH 4 . We demonstrate that contraction can play a crucial role in the effective decomposition of methane with value-added products and that both the electronic and thermal properties of plasma gas are responsible for this effect.

RF plasma↗
DOE OSTI2021

Design and optimization of the RF input-coupler for a low-frequency, split-coaxial RFQ

The Isotope Decay-At-Rest experiment (IsoDAR) is a proposed underground experiment which is expected to be a definitive search for sterile neutrinos. In order to be decisive within 5 years, high rates of neutrinos must be produced, by impinging a 10 mA continuous wave proton beam at 60 MeV on a high power target. Due to space restrictions, a compact cyclotron was chosen as an accelerator to produce this driver beam. To overcome space charge limitations during injection, H 2 + ions are accelerated and later stripped into protons by means of a carbon foil. IsoDAR uses an especially designed low-frequency (32.8 MHz) split-coaxial Radio-Frequency Quadrupole (RFQ) to effectively bunch H 2 + ions before injecting them into this cyclotron. The RFQ will be embedded vertically in the cyclotron yoke, facilitating a very compact design. This puts stringent limits on RFQ size, type, and accessibility. Here, we present the design and optimization of the low-frequency (32.8 MHz) RF input-coupler for the IsoDAR RFQ. The design is challenging due to the necessarily small diameter of the RFQ (28 cm) and the split-coaxial type, as well as limited access to the RFQ. We have determined the optimal position and shape for the coupler, leading to a low power consumption of < 6 kW for an inter-vane voltage of 22 kV. Finally, the highest calculated fields are safely below the Kilpatrick limit for this structure.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Phase transformation and growth mechanism of RF sputtered ferroelectric lead scandium tantalate (PbSc 0.5 Ta 0.5 O 3 ) films

Lead scandium tantalate (PbSc 0.5 Ta 0.5 O 3 , PST), an order/disorder ferroelectric, is a potential candidate for electrocaloric cooling and pyroelectric infrared (IR) detector. In this work, we report the phase transformation kinetics from two series of samples containing pure amorphous and mixture of amorphous and pyrochlore to desired perovskite phase using postdeposition rapid thermal processing (RTP) as well as growth mechanism of RF sputtered PST thin films using excess lead target on platinized silicon (Pt/Ti/SiO 2 /Si) substrates. We find that small changes in the temperature ramp have a large effect on the degree of perovskite conversion (ferroelectric phase), orientation (crystallographic texture), and long-range order parameter (< S 111 >). Through isothermal annealing, we obtained optimal perovskite phase at ≥700°C temperature. The phase transformation is characterized by spontaneous formation of center-type in-plane radial rosette-like structures revealed by scanning electron microscopy. The PST perovskite crystallites were found to coexist with pyrochlore in RTP annealed films. The volume fractions for perovskite and pyrochlore phase were obtained from the analysis of “rosettes” and respective X-ray diffraction intensities which helped to determine various parameters associated with phase kinetics (n, k, and activation energy, Ea) and accompanying growth. The effective activation energies of perovskite transition and growth were found to be 332 ± 11 kJ/mol (345 ± 11 kJ/mol) and 114 ± 10 kJ/mol (122 ± 10 kJ/mol), respectively, for pure amorphous only (and mixed amorphous and pyrochlore) phase following nucleation-growth controlled Avrami's equation. A linear growth rate (n~1) for the perovskite phase indicates predominant interface-controlled process and diffusion-limited phenomena thus inhibiting rosette size owing to reactant depletion and soft impingement at the grain boundary. However, the growth behavior is isotropic in two-dimension parallel to the plane of the substrates for both sample series. Furthermore, lead loss was severe for in-situ growth and RTP combined with conventional furnace annealing than those of RTP only films, which were closer to stoichiometric albeit with excess lead and marginal oxygen vacancies (V o ).

36 MATERIALS SCIENCE↗
DOE OSTI2025

First in operando transient grating spectroscopy measurements on tungsten during high flux plasma operation in PISCES-RF

This work details the construction and first in operando transient grating spectroscopy measurements conducted on PISCES-RF during plasma operation. A preliminary study on a tungsten sample with varied plasma species (Ar and D 2 ), ion flux (4 × 10 21 to 6 × 10 22 ion/m 2 /s), ion energy (5 to 80 eV), and surface temperature (20 to 200 °C) is presented. Prior to plasma exposure, the thermal diffusivity and surface acoustic wave (SAW) speed, (6.9 ± 0.2) × 10 −5 m 2 /s and (2.66 ± 0.02) km/s, were measured in situ with a thermal grating period of 12.5 μm. During Ar plasma exposure, these two quantities vary according to the sample surface temperature. At low flux and varied ion energy, D 2 plasma exposure also results in thermal diffusivity and SAW speed varying with surface temperature alone. At high flux, D 2 plasma exposure results in no convincing change to the thermal diffusivity, but the SAW speed is reduced. After returning to 20 °C, post plasma exposures, the thermal diffusivity and SAW speed almost recover to the initial value prior to exposure.

Surface acoustic wave SAW↗
DOE OSTI2021

An integrated approach to understanding RF vacuum arcs

Although used in the design and costing of large projects such as linear colliders and fusion tokamaks, the theory of vacuum arcs and gradient limits is not well understood. Almost 120 years after the isolation of vacuum arcs, the exact mechanisms of the arcs and the damage they produce are still being debated. We describe our simple and general model of the vacuum arc that can incorporate all active mechanisms and aims to explain all relevant data. Our four stage model, is based on experiments done at 805 MHz with a variety of cavity geometries, magnetic fields, and experimental techniques as well as data from Atom Probe Tomography and failure analysis of microelectronics. The model considers the trigger, plasma formation, plasma evolution and surface damage phases of the RF arc. This paper also examines how known mechanisms can explain the observed sharp field dependence, fast breakdown times and observed surface damage. We update the model and discuss new features while also pointing out where new data would be useful in extending the model to a wider range of frequencies.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2020

Upgrading the LANSCE accelerator with a SNS RF-driven H− ion source

The LANSCE accelerator is currently powered by a filament-driven, biased converter-type H− ion source that operates at 10%, the highest plasma duty factor for this type of source, using only ∼2.2 SCCM of H2. The ion source needs to be replaced every 4 weeks, which takes up to 4 days. The measured negative beam current of 12–16 mA falls below the desired 24 mA acceptance of the LANCSE accelerator. The SNS (Spallation Neutron Source) RF-driven, H− ion source injects ∼50 mA of H− beam into the SNS accelerator at 60 Hz with a 6% duty factor and an availability of >99.5% but requires ∼30 SCCM of H2. Up to 7 A h of H− have been produced during the 14-weeks-long source service cycles, which is unprecedented for small emittance, high-current, pulsed H− ion sources. The emittance of the SNS source is slightly smaller than the emittance of the LANSCE source. The SNS source also features unrivaled low Cs consumption and can be installed and started up in <12 h. LANSCE and SNS are working toward the use of SNS H− ion sources on the LANSCE accelerator because they could (a) fill the LANSCE accelerator to its capacity, (b) decrease the source replacement time by a factor of up to 7, and (c) increase source lifetime by a factor of about 4. This paper discusses some of the challenges that emerge when trying to match a different H− source into an existing injector with significantly different characteristics and operating regimes.

Stockli, Martin P.↗
DOE OSTI2020

Crystallization of TiO 2 polymorphs from RF-sputtered, amorphous thin-film precursors

Crystalline TiO 2 films of anatase, brookite, and rutile are reproducibly made from amorphous precursors deposited by RF magnetron sputtering, producing large-area, single phase films of uniform thickness. Sputtered amorphous TiO 2 precursor thin films follow the general behavior observed for amorphous precursor thin films generated by pulsed laser deposition, namely, that oxygen deficiency is necessary for the formation of brookite and rutile. We quantify the oxygen deficiency and correlate it with the long wavelength optical absorption. We find that the precursor deposition rate is also a contributing factor to phase selection and that brookite and rutile form from films deposited more rapidly and anatase from films deposited more slowly. Sputtered and pulsed laser deposited amorphous precursor films prepared with similar oxygen deficiency and similar thickness result in the same final state after annealing, but the rate for sputtered precursors is slower.

14 SOLAR ENERGY↗
DOE OSTI2020

Demonstration of nitrogen-incorporated ultrananocrystalline diamond photocathodes in a RF gun environment

Quantum efficiency (QE), intrinsic emittance, and robustness are the three most important figures of merit for photocathodes, the first two determine the ultimate achievable brightness of an electron beam, and the third one directly correlates with the complications of a beamline design. Nitrogen-incorporated ultrananocrystalline diamond [(N)UNCD] materials are promising candidates for photocathode applications due to their remarkable electron emission performance as well as the moderate vacuum requirement. Two (N)UNCD photocathodes have been characterized in a realistic RF gun environment with the nicely balanced performance of all three figures of merit. In this work, the QE of the first (N)UNCD cathode (stored in air for two years before the test) was found to be 3.8 x 10 –4 using a 262 nm UV laser and a cathode surface field of 30MV/m. It was found that the QE of the second (N)UNCD sample (grown days before the test) was nearly the same and, therefore, demonstrates the exceptional environmental tolerance of the material. The intrinsic emittance of (N)UNCD was measured to be 1.00 μm/mm.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Experimental and theoretical study of hole scattering in RF sputtered p-type Cu 2 O thin films

One of the key materials of interest for p-type oxide semiconductor thin film electronics is cuprous oxide (Cu 2 O), due to its relatively high hole mobility. Here, in this work, we use experiments, analytical models, and density functional theory calculations to study the scattering mechanisms that determine Hall mobility in two Cu 2 O samples. First, we examine a polycrystalline Cu 2 O thin film deposited by RF magnetron sputtering, and second, a single-crystalline Cu2O bulk substrate. Temperature-dependent Hall measurements indicate that neutral impurity and grain boundary scattering are dominant for the polycrystalline Cu 2 O thin film, while phonon scattering is dominant for single-crystalline Cu 2 O. Our first-principles calculations show that the room-temperature intrinsic hole mobility of Cu 2 O is 106 cm 2 V –1 s –1 , indicating the great promise of the material for p-type electronic devices. This intrinsic mobility is limited by phonon scattering, with the most dominant scattering modes having phonon energies of 88.4 and 17.1 meV. These results indicate that the key pathways to increase the hole mobility in Cu 2 O thin films are by reducing the impurity concentration and by increasing grain size. Our work thus sets the stage for the future development of high performance Cu 2 O-based p-type thin film transistors.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of substrate and growth method on vanadium dioxide thin films by RF magnetron sputtering: Vanadium metal oxidation vs reactive sputtering

Vanadium dioxide (VO 2 ) undergoes a metal–insulator phase transition at ~70 °C and has attracted substantial interest for potential applications in electronics, including those in neuromorphic computing. The vanadium–oxygen system has a rather complicated phase diagram, and controlling the stoichiometry and the phase of thin films of vanadium oxides is a well-known challenge. Here, we explore the novel combination of two methods of VO 2 thin film deposition using off-axis RF magnetron sputtering on (100)- and (111)-oriented yttria-stabilized zirconia (YSZ) substrates: reactive sputtering of vanadium in an oxygen environment and sputtering of vanadium metal followed by oxidation to VO 2 . Interestingly, the reactive sputtering process on both substrate orientations yields the metastable semiconducting VO 2 (B) phase, which is structurally stabilized by the YSZ surface. The metal sputtering and oxidation process on YSZ produces mainly the equilibrium monoclinic (or M1) phase of VO 2 that exhibits a metal–insulator transition. Using this method, we obtained thin films of (010)-textured polycrystalline VO 2 (M1) that show a metal–insulator transition with an on/off ratio larger than 1000.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Towards fast, accurate predictions of RF simulations via data-driven modeling: Forward and lateral models

Three machine learning techniques (multilayer perceptron, random forest, and Gaussian process) provide fast surrogate models for lower hybrid current drive (LHCD) simulations. A single GENRAY/CQL3D simulation without radial diffusion of fast electrons requires several minutes of wall-clock time to complete, which is acceptable for many purposes, but too slow for integrated modeling and real-time control applications. More accurate simulations with fast electron diffusion are even slower, requiring multiple hours of run time with parallel processing. The machine learning models use a database of 16,000+ GEN-RAY/CQL3D simulations for training, validation, and testing. Latin hypercube sampling methods implemented in πScope ensure that the database covers the range of 9 input parameters (n e0 , T e0 , I p , B t , R 0 , n ∥︀ , Z e f f , V loop , P LHCD ) with sufficient density in all regions of parameter space. The surrogate models reduce the computation time from minutes-hours to ms with high accuracy across the input parameter space. Data-driven surrogate models also allow for solving inverse and “lateral” problems. A surrogate model for the inverse problem maps from a desired current drive or power deposition profile to a set of input parameters that would result in such a profile, while a surrogate model for the lateral problem maps from a measured experimental quantity such as hard x-ray emission to a current drive or power deposition profile. In conclusion, the πScope database creation workflow is flexible and applicable to other RF simulation codes such as TORIC.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Helicon edge heating in Proto-MPEX: Azimuthally resolved RF modeling

The Material Plasma Exposure eXperiment (MPEX) is a linear device under construction at ORNL. MPEX employs a variety of heating systems, including a helicon antenna, which is the subject of this work. Lacking a resonant absorption mechanism, as tokamaks have, modeling the RF power absorption in such antennas requires detailed consideration of cold collisional physics. Previous modeling of the heating in this antenna was done exclusively in 2D, assuming axisymmetry and a single azimuthal mode number m = 1⁠. In this study, we introduce a fully 3D model. By including the full 3D physics, with its self-consistent geometry-imposed azimuthal spectrum, we are able to reproduce the experimentally observed transition from edge heating to core heating.

Tierens, Wouter [Oak Ridge National Laboratory (OR↗
DOE OSTI2021

Analysis of Design Alternatives of Actively Cooled RF Window for MPEX

The Materials Plasma Exposure eXperiment (MPEX) has been designed as a linear plasma divertor simulator in order to address plasma material interaction (PMI) science for next-generation fusion devices. It will have the capability to test neutron irradiated samples with plasma fluxes of greater than 10 24 m -2 s -1 . It is expected to operate steady state for up to 10 6 s to consider PMI affects through reactor end of life. The conceptual design of MPEX was completed in 2019, with preliminary design having begun in 2020. The plasma source for MPEX is a helicon antenna, where the energized helical antenna sits outside of the vacuum in order to minimize impurities in the plasma. It is expected to receive up to 200 kW of continuous power, and so the antenna and the window must be actively cooled. The water-cooled copper antenna has been operated at full power on the Proto-MPEX device (which is a test facility to demonstrate the plasma source and heating systems). The water-cooled window, however, is a novel component that must meet numerous competing requirements. It requires a low dielectric loss to allow the Radio Frequency (RF) power to create the plasma within the vacuum boundary. It must be structurally robust to handle the significant heat flux from the plasma and any heat from dielectric coupling. It must be compatible with the coolant (preferably water). It requires a vacuum seal that minimizes impurities into the plasma and does not compromise the structural integrity of the window. Two window designs have been tested. Results from these tests, where temperatures are measured and heat fluxes inferred from infrared camera data, have been correlated with thermal-structural simulations. When these simulations are extrapolated to the full power steady-state heat fluxes that are expected in MPEX, the designs do not appear to have the necessary structural robustness. This study explores design alternatives for the MPEX helicon antenna window, presents analysis results for several of the alternatives, and shows a viable solution that satisfies the requirements for MPEX operation.

Tipton Jr, Joseph↗
DOE OSTI2020

Spatially resolved absolute densities of reactive species and positive ion flux in He-O 2 RF-driven atmospheric pressure plasma jet: touching and non-touching with dielectric substrate

Atmospheric pressure plasma jets (APPJs) are operating in direct contact with dielectric substrates for many applications. Nonetheless, many studies have been focusing on free jets. In this letter, we report spatially resolved measurements of reactive species including neutral and ionic species in an He + 1% O 2 RF-driven APPJ by molecular beam mass spectrometry equipped with a dielectric sampling plate, enabling to detect species densities for APPJ operating remotely or in direct contact with a substrate. Here, the spatially resolved distribution of O, O 2 (a 1 Δ g ) and O 3 is dominated by convection and, remarkably, shows minimum differences between touching and non-touching conditions.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2022

Characterizing W sources in the all-W wall, all-RF WEST tokamak environment

In this work, experimental data, together with interpretive modeling tools, are examined to study trends in the tungsten (W) source in the all-W environment of the WEST tokamak, both from the divertor and from the main chamber. In particular, a poloidal limiter protecting an ion cyclotron resonance heating (ICRH) antenna is used as proxy for main chamber sourcing. The key study is carried out by stepping up lower hybrid current drive (LHCD) power, as the only auxiliary power source. Limiter and divertor W sources exhibit a qualitatively similar proportionality to the total power crossing the separatrix, P SEP , although the main chamber source remains substantially lower than the divertor source, for the range of P SEP accessible in the experiments. Intepretive modeling of the limiter source is carried out with a particle-in-cell (PIC) sheath model coupled to a surface sputtering model. Oxygen is used as a proxy for all light impurity species allowing for characterization of the critical W erosion regions. To get a good quantitative match to the data, it is necessary to assume that the oxygen arrives at the surface mostly at high ionization stages (4+ and above). A separate simulation with SOLEDGE-EIRENE, constrained to measured upstream scrape-off-layer plasma profiles, gives oxygen fractional abundances that are compatible with the PIC simulation result. This is understood to arise from transport processes that dominate over recombination. Substituting the LHCD by ICRH, in an equivalent experiment, the local W source exhibits a 3× enhancement. This can be matched by the simulation, by assuming local RF electric field rectification, based on ~100 eV peak-to-peak, near-antennna electric field. This work has highlighted the particular importance of understanding the ion charge state balance of light impurities as these are most likely the dominant sputtering species in fusion devices with high-Z walls.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Smooth, homogeneous, high-purity Nb 3 Sn superconducting RF resonant cavity by seed-free electrochemical synthesis

Abstract Workbench-size particle accelerators, enabled by Nb 3 Sn-based superconducting radio-frequency (SRF) cavities, hold the potential of driving scientific discovery by offering a widely accessible and affordable source of high-energy electrons and x-rays. Thin-film Nb 3 Sn RF superconductors with high quality factors, high operation temperatures, and high-field potentials are critical for these devices. However, surface roughness, non-stoichiometry, and impurities in Nb 3 Sn deposited by conventional Sn-vapor diffusion prevent them from reaching their theoretical capabilities. Here we demonstrate a seed-free electrochemical synthesis that pushes the limit of chemical and physical properties in Nb 3 Sn. Utilization of electrochemical Sn pre-deposits reduces the roughness of converted Nb 3 Sn by five times compared to typical vapor-diffused Nb 3 Sn. Quantitative mappings using chemical and atomic probes confirm improved stoichiometry and minimized impurity concentrations in electrochemically synthesized Nb 3 Sn. We have successfully applied this Nb 3 Sn to the large-scale 1.3 GHz SRF cavity and demonstrated ultra-low BCS surface resistances at multiple operation temperatures, notably lower than vapor-diffused cavities. Our smooth, homogeneous, high-purity Nb 3 Sn provides the route toward high efficiency and high fields for SRF applications under helium-free cryogenic operations.

Physics↗
DOE OSTI2022

Development of a direct-sampling RF receiver for precision beam charge measurements in the MOLLER experiment

Here, we have developed and tested a direct-sampling RF receiver capable of measuring the amplitude of a 1497 MHz sinusoidal beam signal in 0.5 ms integration windows with a relative uncertainty of better than 10 parts per million. The receiver is intended for measuring signals from beam current monitoring cavities on the beamline of the Continuous Electron Beam Accelerator Facility (CEBAF) at Jefferson Lab. The beam signal strength, frequency, and integration window fulfill the thus far unmet requirements of the upcoming MOLLER experiment to measure the beam charge for different helicity states.

47 OTHER INSTRUMENTATION↗