Search NASA⌕ Search

SEARCH · Search NASA

Results for “rose”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Results from a wake-steering experiment at a commercial wind plant: investigating the wind speed dependence of wake-steering performance

Wake steering is a wind farm control strategy in which upstream wind turbines are misaligned with the wind to redirect their wakes away from downstream turbines, thereby increasing the net wind plant power production and reducing fatigue loads generated by wake turbulence. In this paper, we present results from a wake-steering experiment at a commercial wind plant involving two wind turbines spaced 3.7 rotor diameters apart. During the 3-month experiment period, we estimate that wake steering reduced wake losses by 5.6% for the wind direction sector investigated. After applying a long-term correction based on the site wind rose, the reduction in wake losses increases to 9.3%. As a function of wind speed, we find large energy improvements near cut-in wind speed, where wake steering can prevent the downstream wind turbine from shutting down. Yet for wind speeds between 6–8 m/s, we observe little change in performance with wake steering. However, wake steering was found to improve energy production significantly for below-rated wind speeds from 8–12 m/s. By measuring the relationship between yaw misalignment and power production using a nacelle lidar, we attribute much of the improvement in wake-steering performance at higher wind speeds to a significant reduction in the power loss of the upstream turbine as wind speed increases. Additionally, we find higher wind direction variability at lower wind speeds, which contributes to poor performance in the 6–8 m/s wind speed bin because of slow yaw controller dynamics. Further, we compare the measured performance of wake steering to predictions using the FLORIS (FLOw Redirection and Induction in Steady State) wind farm control tool coupled with a wind direction variability model. Although the achieved yaw offsets at the upstream wind turbine fall short of the intended yaw offsets, we find that they are predicted well by the wind direction variability model. When incorporating the expected yaw offsets, estimates of the energy improvement from wake steering using FLORIS closely match the experimental results.

17 WIND ENERGY↗

Television observations from Surveyor III

Surveyor III landed on the lunar surface at 00:04 GMT, on Day 110, 1967, approximately 23 hr after local sunrise on the Moon. The first pictures were taken by the television camera at 01:02 GMT. The camera was operated extensively for the first period of lunar visibility from the Goldstone Tracking Station of the Deep Space Network and, except on Day 115, on each successive Goldstone pass of the Moon until the Sun set over the Surveyor III landing site on Day 123. During this period, the Sun rose from an elevation angle of 11° in the east to within 3° of the zenith and then sank almost due west of the spacecraft. Many pictures were obtained of the illuminated eastern horizon in the period immediately preceding sunset. In addition to those received at the Goldstone Station, some were obtained at the Canberra, Australia, station of the Deep Space Network. There were 6315 television pictures taken during the first lunar day of the Surveyor III mission.

Surveyor III spacecraft↗

Development of a solid electrolyte carbon dioxide and water reduction system for oxygen recovery

A 1/4-man solid electrolyte oxygen regeneration system, consisting of an electrolyzer, a carbon deposition reactor, and palladium membranes for separating hydrogen, was operated continuously in a 180-day test. Oxygen recovery from the carbon dioxide-water feed was 95%. One percent of the oxygen was lost to vacuum with the hydrogen off-gas. In a space cabin, the remaining 4% would have been recycled to the cabin and recovered. None of the electrolysis cells used in the 180-day test failed. Electrolysis power rose 20% during the test; the average power was 283.5 watts/man. Crew time was limited to 18 min/day of which 12 min/day was used for removing carbon. The success achieved in operating the system can be attributed to an extensive component development program, which is described. Stability of operation, ease of control, and flexibility in feed composition were demonstrated by the life test.

Elikan, L.↗

Optimum runway orientation relative to crosswinds

Specific magnitudes of crosswinds may exist that could be constraints to the success of an aircraft mission such as the landing of the proposed space shuttle. A method is required to determine the orientation or azimuth of the proposed runway which will minimize the probability of certain critical crosswinds. Two procedures for obtaining the optimum runway orientation relative to minimizing a specified crosswind speed are described and illustrated with examples. The empirical procedure requires only hand calculations on an ordinary wind rose. The theoretical method utilizes wind statistics computed after the bivariate normal elliptical distribution is applied to a data sample of component winds. This method requires only the assumption that the wind components are bivariate normally distributed. This assumption seems to be reasonable. Studies are currently in progress for testing wind components for bivariate normality for various stations. The close agreement between the theoretical and empirical results for the example chosen substantiates the bivariate normal assumption.

Falls, L. W.↗

A unified approach to the classification of visual data systems.

Description of an approach to attaining a unified means of characterizing film, TV, and optical data systems. The concept is based on the premise that all of these imaging systems can be described by an equation similar to the ideal imaging system described by Rose (1948). This technique permits the direct comparison of film and TV performance without converting speed, film resolution lines, TV resolution lines, highlight output current and video bandwidth into compatible units, only to find some essential element of the conversion has been omitted from the particular specification in use. Most important, it permits system performance criteria to be based on input and output criteria without extensive manipulation of the elements between input and output.

Black, J.↗

Erythropoietic radiosensitivity of the rat during altitude acclimatization.

The effect of a sublethal dose (300 R) of X-radiation upon the erythropoietic system of the rat, during 60-day acclimatization to moderate hypoxia (3,800 m altitude), was studied. Past work has shown that hypoxic animals are damaged less by radiation than animals irradiated in a normal environment; therefore, it was postulated that if, after acclimatization to hypoxia the bone marrow oxygen tension returns to sea-level values, these animals should suffer radiation damage equivalent to animals at sea level. The principal parameters followed were the rate of depletion of injected Fe-59 from the plasma of chronically catheterized rats, and its subsequent reappearance in the circulating erythrocytes. After 20 days of acclimatization, both parameters for altitude-irradiated animals returned to the values of animals irradiated at sea level, previously having reflected increased erythropoiesis. In altitude nonirradiated animals the parameters indicated erythropoietic stimulation persisting up to 45 days acclimatization. The protective effect of the hypoxia on the stem cells vanished during acclimatization, presumably as cellular oxygen tension rose.

Gaugl, J. F.↗

Creating new cities through the large air-cushion vehicle.

The air-cushion vehicle (ACV) can travel over concrete roads, grass, sand, mud, swamp, snow, ice, and water. This mobility makes possible a totally new geographical freedom in choosing transportation routes, locating ports, and laying out a city. By the 1980s fleets of large ACV freighters could begin carrying ocean-going cargo. The mobility of an ACV fleet would allow placing hoverports away from areas now crowded. New cities could rise along shallow or reef-bound seacoasts and rivers, just as cities once rose around deep-water seaports.

Anderson, J. L.↗

Photogrammetric and photometric investigation of a smoke plume viewed from space.

Use of detailed analyses of an Apollo 6 stereographic photograph of a smoke plume which originated in southern Arizona and crossed over into Mexico to illustrate how high-resolution photography can aid meteorologists in evaluating specific air pollution events. Photogrammetric analysis of the visible smoke plume revealed that the plume was 8.06 miles long and attained a maximum width of 4000 ft, 3.0 miles from the 570-ft chimney emitting the effluent. Stereometric analysis showed that the visible top of the plume rose nearly 2400 ft above stack top, attaining 90% of this total rise 1.75 miles downwind from the source. Photometric analysis of the plume revealed a field of plume optical density that portrayed leptokurtic and bimodal distributions rather than a true Gaussian distribution. A horizontal eddy diffusivity of about 650,000 sq cm/sec and a vertical eddy diffusivity of 230,000 sq cm/sec were determined from the plume dimensions. Neutron activation analysis of plume samples revealed the elemental composition of the smoke to be copper, arsenic, selenium, indium and antimony, with trace amounts of vanadium and scandium.

Randerson, D.↗

Vacuum measurements on the lunar surface.

Results of measurements of neutral gas pressure on the lunar surface made with a cold cathode ionization gauge carried to the moon by Apollo 14. The vacuum quality at the landing site is much influenced by the adsorption of rocket gases and their later release. During surface operations by the astronauts, the pressure was near 10 to the minus 8th torr. No data were obtained between the time of the surface operations and lunar sunset about 12 days later, at which time the temperature fell rapidly to the vicinity of 100 K. The pressure was about 10 to the minus 12th torr shortly after sunset, but intermittent releases of gas, perhaps from within the moon itself, occasionally raised the pressure by less than an order of magnitude for as long as a day or two at a time and on one occasion to about 10 to the minus 10th torr for about an hour. At lunar sunrise, as the surface was warmed rapidly to about 300 K, the pressure rose rapidly to about 10 to the minus 10th torr, most likely due to the release of absorbed gases in the immediate landing area or on the landing module itself. For comparison with interplanetary vacuum conditions, the directed pressure of the solar wind is usually less than 10 to the minus 11th torr and the pressure of random gas motion within the solar wind, less than 10 to the minus 13th torr.

Johnson, F. S.↗

The 6300 A predawn enhancement - Excitation by photoelectrons from the magnetic conjugate point.

Incoherent scatter and tilting filter photometer data from Arecibo Observatory were combined to search for a contribution to the 6300 A predawn enhancement due to impact excitation by photoelectrons from the magnetic conjugate point. Prior to about 105 deg conjugate solar zenith angle, calculations of the 6300 A intensities due to dissociative recombination gave good agreement with the observed intensities. Then, with the arrival of conjugate photoelectrons (confirmed by plasma line enhancements), the observed intensities rose above the calculated, the difference increasing until a plateau was achieved at a conjugate solar zenith angle of about 95 deg. The difference or residual intensity is attributed to direct photoelectron impact excitation. Significant day-to-day variations in the onset angle and intensity have a strong negative correlation with ionospheric electron density.

Wickwar, V. B.↗

Synthesis of Jicamarca data during the great storm of March 8, 1970.

Continuous measurement of electron temperature and electron concentration during the great magnetic storm of Mar. 8, 1970, when the F2 peak rose as high as 800 km. Continuous measurements of the vertical component of E x B drift were made from 1130 to 1730 LT. A synthesis of the observed electron concentrations was made using a model that solved the time-dependent electron-ion continuity equation for O(+) and the molecular ions; the latter chemistry was included to improve the solutions at lower heights. It was found, using the observed values of vertical drift, that most of the observed features of the F2-region ionosphere were synthesized by the model. An interpretation of the synthesis that emphasizes the importance of horizontal diffusion at the equator is given. Observations are presented for Mar. 7, 8, and 9, 1970, including the Huancayo magnetograms, which display a close correlation with the drift measurements.

Woodman, R. F.↗

Martian lineaments from Mariner 6 and 7 photographs

Mariner 6 and 7 photographs were used to investigate the nature and importance of linear surface trends on Mars. Cross correlations of frequency-azimuth distributions of linear trends from different Mariner frames indicate that lineations not recognized as topographic features have a component of pseudoforms, probably introduced during digital reconstruction of the pictures. Similar statistical tests may aid in the analysis of surface trends from future satellites and space probes. The most reliable data were separated into photometrically defined provinces. Meridiani Sinus and Margaritifer Sinus display five major trends in common, which are interpreted as extensions of crustal weaknesses related to the enormous equatorial canyon revealed in Mariner 6 and 9 pictures. Alignments of crater wall segments generally match these trends and suggest structural control of crater plan. Crater chains, however, do not match these trends and are interpreted as secondary impacts. Rose diagrams of lineations in Deucalionis Regio exhibit much more complexity and are believed to reflect a better preserved or more complex geologic history.

Schultz, P. H.↗

Analysis of photo linear elements, Laramie Mountains, Wyoming

The author has identified the following significant results. Photo linear features in the Precambrian rocks of the Laramie Mountains are delineated, and the azimuths plotted on rose diagrams. Three strike directions are dominant, two of which are in the northeast quadrant. Laramide folds in the Laramie basin to the west of the mountains appear to have the same trend, and apparently have been controlled by response of the basement along fractures such as have been measured from the imagery.

Blackstone, D. L., Jr.↗

To evaluate ERTS-1 data for usefulness as a geological sensor in the diverse geological terraines of New York State

The author has identified the following significant results. Linear anomalies dominate the new geological information derived from ERTS-1 imagery, total lengths now exceeding 6000 kms. Experimentation with a variety of viewing techniques suggests that conventional photogeologic analyses of band 7 results in the location of more than 97 percent of all linears found. Bedrock lithologic types are distinguishable only where they are topographically expressed or govern land use signatures. The maxima on rose diagrams for ERTS-1 anomalies correspond well with those for mapped faults and topographic lineaments, despite a difference in relative magnitudes of maxima thought due to solar illumination direction. A multiscale analysis of linears showed that single topographic linears at 1:2,500,000 became dashed jugate linears at 1:500,000, and shorter linears lacking any conspicuous zonal alignment at 1:250,000. Most circular features found were explained away by U-2 airphoto analysis but several remain as anomalies. Visible glacial features include individual drumlins, best seen in winter imagery, drumlinoids, eskers, ice-marginal drainage channels, glacial lake shorelines and sand plains, and end moraines.

Isachsen, Y. W.↗

Sputter erosion and deposition in the discharge chamber of a small mercury ion thruster

A 5 cm diameter mercury ion thruster similar to one tested for 9715 hours was operated approximately 400 hrs each at discharge voltages of 36.6, 39.6, and 42.6 V, with corresponding discharge propellant utilizations of 58, 68, and 70 percent. The observed sputter erosion rates of the internal thruster parts and the anode weight gain rate all rose rapidly with discharge voltage and were roughly in the ratio of 1:3:5 for the three voltages. The combined weight loss of the internal thruster parts nearly balanced the anode weight gain. Hg(+2) ion apparently caused most of the observed erosion.

Power, J. L.↗

Stream network analysis from orbital and suborbital imagery, Colorado River Basin, Texas

The author has identified the following significant results. Orbital SL-2 imagery (earth terrain camera S-190B), received September 5, 1973, was subjected to quantitative network analysis and compared to 7.5 minute topographic mapping (scale: 1/24,000) and U.S.D.A. conventional black and white aerial photography (scale: 1/22,200). Results can only be considered suggestive because detail on the SL-2 imagery was badly obscured by heavy cloud cover. The upper Bee Creek basin was chosen for analysis because it appeared in a relatively cloud-free portion of the orbital imagery. Drainage maps were drawn from the three sources digitized into a computer-compatible format, and analyzed by the WATER system computer program. Even at its small scale (1/172,000) and with bad haze the orbital photo showed much drainage detail. The contour-like character of the Glen Rose Formation's resistant limestone units allowed channel definition. The errors in pattern recognition can be attributed to local areas of dense vegetation and to other areas of very high albedo caused by surficial exposure of caliche. The latter effect caused particular difficulty in the determination of drainage divides.

Baker, V. R.↗

Evaluation of ERTS-1 imagery for spectral geological mapping in diverse terranes of New York State

The author has identified the following significant results. Linear anomalies dominate the new geological information derived from ERTS-1 imagery, total lengths now exceeding 6000 km. Experimentation with a variety of viewing techniques suggest that conventional photogeologic analyses of band 7 results in the location of more than 97 percent of all linears found. Bedrock lithologic types are distinguishable only where they are topographically expressed or govern land use signatures. The maxima on rose diagrams for ERTS-1 anomalies correspond well with those for mapped faults and topographic lineaments. A multiscale analysis of linears showed that single topographic linears at 1:2,500,000 became dashed linears at 1:1,000,000 aligned zones of shorter parallel, en echelon, or conjugate linears at 1:500,00. Most circular features found were explained away by U-2 airphoto analysis but several remain as anomalies. Visible glacial features include individual drumlins, best seen in winter imagery, drumlinoids, eskers, ice-marginal drainage channels, glacial lake shorelines and sand plains, and end moraines.

Isachsen, Y. W.↗

A review of turbulence measurements in compressible flow

A survey of turbulence measurements in compressible flows is presented. The majority of turbulence measurements at super- and hypersonic speeds were made for the zero pressure gradient, turbulent boundary layer. It was found that the nondimensional turbulent stress terms for the zero pressure gradient flow appear to agree closely with equivalent incompressible measurements in the outer part of the boundary layer. The stress terms were nondimensionalized by the wall value of shear stress and plotted versus the distance from the wall, nondimensionalized by the boundary-layer thickness. Indirect evaluation of the total shear stress distribution from mean velocity measurements for both super- and hypersonic flows (zero pressure gradient, two-dimensional flows) indicate a near universal distribution. These total shear stress curves also agree very closely with measured incompressible shear stress distributions. Recent laser anemometer measurements of the turbulent Reynolds shear stress (puv), reported by Johnson and Rose for a Mach number 2.9 flow, are in reasonable agreement with the expected total shear stress curve over the outer 60% of the boundary layer.

Sandborn, V. A.↗