Search NASA⌕ Search

SEARCH · Search NASA

Results for “shuttling effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

The effect of wind variability on Space Shuttle flight

A data base of paired detailed wind profiles is developed for use in evaluating the STS ascent capability. The flight of the Shuttle is simulated through a sequence of measured detailed wind profiles and the wind effects on load and performance are evaluated. Since the wind measurement and simulation time requirements dictate that the launch decision be based on wind measurements taken about 3.5 hr before launch, a data base of paired detailed profiles is obtained in order to account for possible load increases due to wind profile changes during the final 3.5 hr before launch. Results show that the largest wind changes occur in winter at about 12 km altitude. At that time and altitude, it is found that there is a 5 percent risk that the wind component speed change will approximate 10 m/s in 3.5 hr. It is determined that the wind can vary over a period of 3.5 hr by more than 20 percent from the transition season to the winter season while somewhat smaller changes occur between the transition season and the summer season. It is concluded that these results demonstrate the feasibility of the wind change model concept and that this model should be considered for future use in Shuttle prelaunch operations.

Hill, C. K.↗
NASA NTRS1976

Roughness induced transition criteria for space shuttle-type vehicles

Tripping effectiveness of surface roughness on a delta wing shuttle orbiter model at 20 deg angle of attack is compared to that on plane and axisymmetrical bodies with and without longitudinal pressure gradients. The experimental data presented are compared on the basis of effective roughness Reynolds number since this parameter is not sensitive to flow conditions downstream of the roughness. The discussion covers the effective roughness Reynolds number as a function of roughness position Reynolds number, effective size ratio as a function of pressure gradient and distance from vehicle nose, and effect of spanwise roughness position on roughness effectiveness. It is shown that conventional criteria for sizing roughness elements which promote transition in two-dimensional zero-pressure gradient flows are insufficient for high-pressure gradient flows and three-dimensional flows. Roughness much smaller than that given by conventional criteria can cause transition and significantly increase the heating load.

Morrisette, E. L.↗
NASA NTRS1981

Effects of rain and fog on the Shuttle Ku-band microwave scanning beam landing system range and accuracy performance

The microwave Scanning Beam Landing System's (MSBLS) performance in fog and rain was studied. The fog and rain effects on the Shuttle Ku-band system were determined. Specifically, microwave attenuation, beam distortion, and coordinate errors resulting from operation of the MSBLS in poor weather conditions were evaluated. The main physical processes giving rise to microwave attenuation were found to be absorption and scattering by water droplets. The general theory of scattering and absorption used is discussed and a listing of applicable computer programs is provided.

Butler, D.↗
NASA NTRS1972

Effects of radiation environment on reusable nuclear shuttle system

Parametric tradeoff analyses of a wide spectrum of alternate tank configurations to minimize both primary and secondary, direct and scattered radiation sources emanating from the NERVA are reported. The analytical approach utilizing point kernel techniques is described and detailed data are presented on the magnitude of neutron/gamma doses for different locations. Single-tank configurations utilizing smaller cone angles and end cap radii were found to minimize integral radiation levels, hence, stage shielding-weight penalties for shuttle missions. Hybrid configurations employing an upper tank with a reduced cone angle and end cap radius result in low integral payload doses primarily due to the increased separation distance caused by the elongation of the larger capacity upper tank. A preliminary radiation damage assessment is discussed of possible reusable nuclear shuttle materials, components, and subsystems, and the possible effects of the radiation environment on various phases of RNS mission operations.

Lane, A. G.↗
NASA NTRS1981

Effect of load eccentricity and substructure deformation on ultimate strength of shuttle orbiter thermal protection system

The effect of load eccentricity and substructure deformation on the ultimate strength and stress displacement properties of the shuttle orbiter thermal protection system (TPS) was determined. The LI-900 Reusable Surface Insulation (RSI) tiles mounted on the .41 cm thick Strain Isolator Pad (SIP) were investigated. Substructure deformations reduce the ultimate strength of the SIP/tile TPS and increase the scatter in the ultimate strength data. Substructure deformations that occur unsymmetric to the tile can cause the tile to rotate when subjected to a uniform applied load. Load eccentricity reduces SIP/tile TPS ultimate strength and causes tile rotation.

Sawyer, J. W.↗
NASA NTRS1979

Shuttle Global Positioning System (GPS) design study

The effects of oscillator noise on Shuttle Global Positioning System (GPS) receiver performance, GPS navigation system self-test, GPS ground transmitter design to augment shuttle navigation, the effect of ionospheric delay modelling on GPS receiver design, and GPS receiver tracking of Shuttle transient maneuvers were investigated.

Nilsen, P. W.↗
NASA NTRS1992

Shared visions: Partnership of Rockwell International and NASA Cost Effectiveness Enhancements (CEE) for the space shuttle system integration program

As a result of limited resources and tight fiscal constraints over the past several years, the defense and aerospace industries have experienced a downturn in business activity. The impact of fewer contracts being awarded has placed a greater emphasis for effectiveness and efficiency on industry contractors. It is clear that a reallocation of resources is required for America to continue to lead the world in space and technology. The key to technological and economic survival is the transforming of existing programs, such as the Space Shuttle Program, into more cost efficient programs so as to divert the savings to other NASA programs. The partnership between Rockwell International and NASA and their joint improvement efforts that resulted in significant streamlining and cost reduction measures to Rockwell International Space System Division's work on the Space Shuttle System Integration Contract is described. This work was a result of an established Cost Effectiveness Enhancement (CEE) Team formed initially in Fiscal Year 1991, and more recently expanded to a larger scale CEE Initiative in 1992. By working closely with the customer in agreeing to contract content, obtaining management endorsement and commitment, and involving the employees in total quality management (TQM) and continuous improvement 'teams,' the initial annual cost reduction target was exceeded significantly. The CEE Initiative helped reduce the cost of the Shuttle Systems Integration contract while establishing a stronger program based upon customer needs, teamwork, quality enhancements, and cost effectiveness. This was accomplished by systematically analyzing, challenging, and changing the established processes, practices, and systems. This examination, in nature, was work intensive due to the depth and breadth of the activity. The CEE Initiative has provided opportunities to make a difference in the way Rockwell and NASA work together - to update the methods and processes of the organizations. The future success of NASA space programs and Rockwell hinges upon the ability to adopt new, more efficient and effective work processes. Efficiency, proficiency, cost effectiveness, and teamwork are a necessity for economic survival. Continuous improvement initiatives like the CEE are, and will continue to be, vehicles by which the road can be traveled with a vision to the future.

Bejmuk, Bohdan I.↗
NASA NTRS1985

Tether Fundamentals

Forces on tethered satellites, tether tension as a function of the effective mass, and parameters of candidate tether materials are examined. Illustrations show: stabilization control law; tethered satellite deployment and retrieval; angular momentum; electric motor effect reboost; a very long tether phenomenon; shuttle tethered satellite effects on the orbiter; artificial gravity; tethered satellite rendezvous docking relative velocity; and scaling up from the shuttle/TSS. Limitations of the tethered satellite system and of tether properties as well as cost/benefits trades for future applications are considered.

Rupp, C.↗
NASA NTRS2000

Reliability of Space-Shuttle Pressure Vessels with Random Batch Effects

In this article we revisit the problem of estimating the joint reliability against failure by stress rupture of a group of fiber-wrapped pressure vessels used on Space-Shuttle missions. The available test data were obtained from an experiment conducted at the U.S. Department of Energy Lawrence Livermore Laboratory (LLL) in which scaled-down vessels were subjected to life testing at four accelerated levels of pressure. We estimate the reliability assuming that both the Shuttle and LLL vessels were chosen at random in a two-stage process from an infinite population with spools of fiber as the primary sampling unit. Two main objectives of this work are: (1) to obtain practical estimates of reliability taking into account random spool effects and (2) to obtain a realistic assessment of estimation accuracy under the random model. Here, reliability is calculated in terms of a 'system' of 22 fiber-wrapped pressure vessels, taking into account typical pressures and exposure times experienced by Shuttle vessels. Comparisons are made with previous studies. The main conclusion of this study is that, although point estimates of reliability are still in the 'comfort zone,' it is advisable to plan for replacement of the pressure vessels well before the expected Lifetime of 100 missions per Shuttle Orbiter. Under a random-spool model, there is simply not enough information in the LLL data to provide reasonable assurance that such replacement would not be necessary.

Feiveson, Alan H.↗
NASA NTRS1988

Failure mode and effects analysis (FMEA) for the Space Shuttle solid rocket motor

The recertification of the Space Shuttle Solid Rocket Booster (SRB) and Solid Rocket Motor (SRM) has included an extensive rewriting of the Failure Mode and Effects Analysis (FMEA) and Critical Items List (CIL). The evolution of the groundrules and methodology used in the analysis is discussed and compared to standard FMEA techniques. Especially highlighted are aspects of the FMEA/CIL which are unique to the analysis of an SRM. The criticality category definitions are presented and the rationale for assigning criticality is presented. The various data required by the CIL and contribution of this data to the retention rationale is also presented. As an example, the FMEA and CIL for the SRM nozzle assembly is discussed in detail. This highlights some of the difficulties associated with the analysis of a system with the unique mission requirements of the Space Shuttle.

Russell, D. L.↗
NASA NTRS1993

NASA's Advanced solid rocket motor

The Advanced Solid Rocket Motor (ASRM) will not only bring increased safety, reliability and performance for the Space Shuttle Booster, it will enhance overall Shuttle safety by effectively eliminating 174 failure points in the Space Shuttle Main Engine throttling system and by reducing the exposure time to aborts due to main engine loss or shutdown. In some missions, the vulnerability time to Return-to-Launch Site aborts is halved. The ASRM uses case joints which will close or remain static under the effects of motor ignition and pressurization. The case itself is constructed of the weldable steel alloy HP 9-4-0.30, having very high strength and with superior fracture toughness and stress corrosion resistance. The internal insulation is strip-wound and is free of asbestos. The nozzle employs light weight ablative parts and is some 5,000 pounds lighter than the Shuttle motor used to date. The payload performance of the ASRM-powered Shuttle is 12,000 pounds higher than that provided by the present motor. This is of particular benefit for payloads delivered to higher inclinations and/or altitudes. The ASRM facility uses state-of-the-art manufacturing techniques, including continuous propellant mixing and direct casting.

Mitchell, Royce E.↗
NASA NTRS1972

Effect of commercial and military performance requirements for transport category aircraft on space shuttle booster design and operation

The effect of two sets of performance requirements, commercial and military, on the design and operation of the space shuttle booster is evaluated. Critical thrust levels are established according to both sets of operating rules for the takeoff, cruise, and go-around flight modes, and the effect on engine requirements determined. Both flyback and ferry operations are considered. The impact of landing rules on potential shuttle flyback and ferry bases is evaluated. Factors affecting reserves are discussed, including winds, temperature, and nonstandard flight operations. Finally, a recommended set of operating rules is proposed for both flyback and ferry operations that allows adequate performance capability and safety margins without compromising design requirements for either flight phase.

Bithell, R. A.↗
NASA NTRS1973

Effect of reaction control system jet-flow field interactions on a 0.015 scale model space shuttle orbiter aerodynamic characteristics

The effects of the reaction control system (RCS) jet-flow field interactions on the space shuttle orbiter system during entry are discussed. The primary objective of the test program was to obtain data for the shuttle orbiter configuration to determine control amplification factors resulting from jet interaction between the RCS plumes and the external flow over the vehicle. A secondary objective was to provide data for comparison and improvement of analytic jet interaction prediction techniques. The test program was divided into two phases; (1) force and moment measurements were made with and without RCS blowing, investigating environment parameters (R sub e, Alpha, Beta), RCS plume parameters (Jet pressure ratio, momentum ratio and thrust level), and geometry parameters (RCS pod locations) on the orbiter model, (2) oil flow visualization tests were conducted on a dummy balance at the end of the test.

Monta, W. J.↗
NASA NTRS2006

Shuttle Return To Flight Experimental Results: Protuberance Effects on Boundary Layer Transition

The effect of isolated roughness elements on the windward boundary layer of the Shuttle Orbiter has been experimentally examined in the Langley Aerothermodynamic Laboratory in support of an agency-wide effort to prepare the Shuttle Orbiter for return to flight. This experimental effort was initiated to provide a roughness effects database for developing transition criteria to support on-orbit decisions to repair damage to the thermal protection system. Boundary layer transition results were obtained using trips of varying heights and locations along the centerline and attachment lines of 0.0075-scale models. Global heat transfer images using phosphor thermography of the Orbiter windward surface and the corresponding heating distributions were used to infer the state of the boundary layer (laminar, transitional, or turbulent). The database contained within this report will be used to formulate protuberance-induced transition correlations using predicted boundary layer edge parameters.

Liechty, Derek S.↗
NASA NTRS1980

Verification of interim simulated atmospheric turbulence

During horizontal and near-horizontal flight of the space shuttle orbiter, the effects of atmospheric turbulence on the vehicle are crucial in establishing the space shuttle design, control, and human pilot effects. The effects of both turbulent gusts and gust gradients (shears) must be taken into account. By means of a nonrecursive turbulence simulation model, twelve simulated turbulence time series for gusts and gust gradients were generated as part of a previous investigation. The current investigation was concerned with the spectral analysis of the time series based on the use of Fourier transform theory. A comparison between the computed spectra and the corresponding von Karman theoretical spectra is also included. A basic difference is explained between the computed and theoretical spectra which was identified as a result of the comparison. Conclusions and recommendations are presented.

Tatom, F. B.↗