Search NASA⌕ Search

SEARCH · Search NASA

Results for “simulation technique”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

A jet controlled magnetic referenced attitude control system for spinning payloads

An attitude control system was designed permitting large angle acquisition and alignment of the principle axis of a spinning payload to within 1 degree of the earth's magnetic field. Signals from magnetometer and gyro sensors are fed to the control algorithm to generate commands for the jet thrusters. The algorithm contains a cross axis magnetometer signal to prevent a large angle magnetometer signal to prevent a large angle equilibrium solution. The acquisition will occur within 50 seconds from initial precession and nutation angles of 30 degrees. An electronic spin filter passes signals at spin and nutation frequencies and rejects bias signals due to sensor misalignment and principle axis offset. Describing function analysis and total analog simulation techniques were used. The flight ACS hardware was interfaced with the analog computer simulation for design and verification. The controller has flown on four successful missions.

Celmer, J. J.↗
NASA NTRS1995

Effects of Meteoroid Erosion in Planetary Rings

This grant supported continuing studies of the effects of ballistic transport on the evolution of Saturn's rings. Ballistic transport, as used in this context, refers to the net transport of mass and angular momentum caused by the exchange of meteoroid impact ejecta between neighboring ring regions (Ip 1983, 1984, Morfill et al. 1983, Lissauer 1984, Durisen 1984a,b). The characteristic time scale associated with this process is the gross erosion time t(sub g) the time it would take a ring region to be completed eroded if all impact ejecta were lost. This time scale is estimated to be about 10(exp 5) to 10(exp 6) years for a ring region with normal optical depth tau approximately 1. Earlier work by myself and collaborators developed the physical theory and simulation techniques to model this process (Durisen et al. 1989, Cuzzi and Durisen 1990). Detailed simulations, supported in part by this grant, have demonstrated that ballistic transport can produce observed structures in Saturn's rings, especially at and near the inner edges of the A and B Rings (Durisen et al. 1992, 1996). The structures of interest in the real rings are illustrated in Figures 1 and 2. Most of these structures were previously unexplained. The computational results plus analytic treatments place useful constraints on fundamental ring properties, including the indication of a relatively young ring age less than or equal 10(exp 8) years (see reviews by Nicholson and Dones 1991, Esposito 1993, Cuzzi 1995, and Porco 1995). This grant also supported development of the faster computational algorithms necessary to permit longer evolutions. Resulting simplications in the ballistic transport equations permitted an analytic linear stability analysis (Durisen 1995), which has provided considerable insight into ballistic transport processes and applications to Saturn's rings. All these accomplishments are described in more detail below.

Durisen, Richard H.↗
NASA NTRS2014

Range Safety Flight Elevation Limit Calculation Software

This program was developed to fill a need within the Wallops Flight Facility workflow for automation of the development of vertical plan limit lines used by flight safety officers during the conduct of expendable launch vehicle missions. Vertical plane present-position-based destruct lines have been used by range safety organizations at numerous launch ranges to mitigate launch vehicle risks during the early phase of flight. Various ranges have implemented data submittal and processing workflows to develop these destruct lines. As such, there is significant prior art in this field. The ElLimits program was developed at NASA's Wallops Flight Facility to automate the process for developing vertical plane limit lines using current computing technologies. The ElLimits program is used to configure launch-phase range safety flight control lines for guided missiles. The name of the program derives itself from the fundamental quantity that is computed - flight elevation limits. The user specifies the extent and resolution of a grid in the vertical plane oriented along the launch azimuth. At each grid point, the program computes the maximum velocity vector flight elevation that can be permitted without endangering a specified back-range location. Vertical plane x-y limit lines that can be utilized on a present position display are derived from the flight elevation limit data by numerically propagating 'streamlines' through the grid. The failure turn and debris propagation simulation technique used by the application is common to all of its analysis options. A simulation is initialized at a vertical plane grid point chosen by the program. A powered flight failure turn is then propagated in the plane for the duration of the so-called RSO reaction time. At the end of the turn, a delta-velocity is imparted, and a ballistic trajectory is propagated to impact. While the program possesses capability for powered flight failure turn modeling, it does not require extensive user inputs of vehicle characteristics (e.g., thrust and aerodynamic data), nor does it require reams of turn data after the traditional fashion of the Air Force ranges. The program requires a nominal trajectory table (time, altitude, range, velocity, and flight elevation) and makes heavy use of it to initialize and model a failure turn.

Lanzi, Raymond J↗
NASA NTRS1992

Atomic oxygen effects on thin film space coatings studied by spectroscopic ellipsometry, atomic force microscopy, and laser light scattering

The University of Nebraska is currently evaluating Low Earth Orbit (LEO) simulation techniques as well as a variety of thin film protective coatings to withstand atomic oxygen (AO) degradation. Both oxygen plasma ashers and an electron cyclotron resonance (ECR) source are being used for LEO simulation. Thin film coatings are characterized by optical techniques including Variable Angle Spectroscopic Ellipsometry, Optical spectrophotometry, and laser light scatterometry. Atomic Force Microscopy (AFM) is also used to characterize surface morphology. Results on diamondlike carbon (DLC) films show that DLC degrades with simulated AO exposure at a rate comparable to Kapton polyimide. Since DLC is not as susceptible to environmental factors such as moisture absorption, it could potentially provide more accurate measurements of AO fluence on short space flights.

Synowicki, R. A.↗
NASA NTRS1989

Analysis of gamma prime shape changes in a single crystal Ni-base superalloy

The microstructural evolution of a commercial single crystal superalloy, NASAIR 100, is analyzed using the existing high-temperature lattice mismatch data and high-temperature moduli obtained from tests on single crystals of gamma and gamma prime. A multiparticle analysis of the microstructural evolution is performed using a novel microstructural lattice simulation technique, MCFET. Under a uniaxial stress, a regular array of gamma prime particles in the simulated microstructure is predicted to coalesce and form a plate morphology, with the broad faces of the plates and stress axis perpendicular in tension but parallel in compression. These results are consistent with changes in gamma prime shape observed in NASAIR 100 following creep testing at 1000 C.

Gayda, J.↗
NASA NTRS1974

Study of ceramic products and processing techniques in space

An analysis of the solidification kinetics of beta alumina in a zero-gravity environment was carried out, using computer-simulation techniques, in order to assess the feasibility of producing high-quality single crystals of this material in space. The two coupled transport processes included were movement of the solid-liquid interface and diffusion of sodium atoms in the melt. Results of the simulation indicate that appreciable crystal-growth rates can be attained in space. Considerations were also made of the advantages offered by high-quality single crystals of beta alumina for use as a solid electrolyte; these clearly indicate that space-grown materials are superior in many respects to analogous terrestrially-grown crystals. Likewise, economic considerations, based on the rapidly expanding technological applications for beta alumina and related fast ionic conductors, reveal that the many superior qualities of space-grown material justify the added expense and experimental detail associated with space processing.

Markworth, A. J.↗
NASA NTRS1974

Role of man in flight experiment payloads, phase 1

The identification of required data for studies of Spacelab experiment functional allocation, the development of an approach to collecting these data from the payload community, and the specification of analytical methods necessary to quantitatively determine the role of man in specific Spacelab experiments are presented. A generalized Spacelab experiment operation sequence was developed, and the parameters necessary to describe each signle function in the sequence were identified. A set of functional descriptor worksheets were also drawn up. The methodological approach to defining the role of man was defined as a series of trade studies using a digial simulation technique. The tradeoff variables identified include scientific crew size, skill mix, and location. An existing digital simulation program suitable for the required analyses was identified and obtained.

Malone, T. B.↗
NASA NTRS1994

Hardware and software reliability estimation using simulations

The simulation technique is used to explore the validation of both hardware and software. It was concluded that simulation is a viable means for validating both hardware and software and associating a reliability number with each. This is useful in determining the overall probability of system failure of an embedded processor unit, and improving both the code and the hardware where necessary to meet reliability requirements. The methodologies were proved using some simple programs, and simple hardware models.

Swern, Frederic L.↗
NASA NTRS2002

Annual Research Briefs, 2002: Center for Turbulence Research

Turbulent combustion remains the largest component of the CTR's core program. This program and several related activities at CTR are supported by NASA's Ultra Efficient Engine Technology Program. It is also intimately connected with the Department of Energy's ASCI program at Stanford which develops the technology for numerical simulation of realistic aircraft engines using state of the art massively parallel computers. In combustion modeling the attention has been directed to the modeling of higher levels of complexity such as spray dynamics, radiation and soot formation. Major aircraft engine manufacturers have shown considerable interest in this program; in particular, a significant active collaboration exists between CTR and the Pratt & Whitney Corporation. CTR's combustion program is essentially based on the large-eddy simulation technique, LES, which is actively being pursued at CTR for this and many other applications. Important accomplishments in LES included simulations with three-dimensional filters which result in grid independent calculations (that is why we call it "true" LES), and the development of the methodology for integration of LES and Reynolds Averaged computations. Optimization techniques are being studied and used for the important problem of wall boundary conditions for LES as well as for optimal shape design for aeroacoustic and aerodynamic performance gains.

ULTRA EFFICIENT ENGINE TECHNOLOGY↗
NASA NTRS1994

Physics-based approach to haptic display

This paper addresses the implementation of complex multiple degree of freedom virtual environments for haptic display. We suggest that a physics based approach to rigid body simulation is appropriate for hand tool simulation, but that currently available simulation techniques are not sufficient to guarantee successful implementation. We discuss the desirable features of a virtual environment simulation, specifically highlighting the importance of stability guarantees.

Brown, J. Michael↗
NASA NTRS1996

High-Performance Computing for the Electromagnetic Modeling and Simulation of Interconnects

The electromagnetic modeling of packages and interconnects plays a very important role in the design of high-speed digital circuits, and is most efficiently performed by using computer-aided design algorithms. In recent years, packaging has become a critical area in the design of high-speed communication systems and fast computers, and the importance of the software support for their development has increased accordingly. Throughout this project, our efforts have focused on the development of modeling and simulation techniques and algorithms that permit the fast computation of the electrical parameters of interconnects and the efficient simulation of their electrical performance.

Schutt-Aine, Jose E.↗
NASA NTRS2019

Numerical analysis of unsteady flow in a converging-diverging nozzle

This study investigates the physics of jet noise by the numerical solution of the three dimensional unsteady Navier-Stokes equations for a low-supersonic jet (Mach numbers on the order of 1.4) from a converging-diverging (C-D) nozzle and mixing with a subsonic surrounding flow. The numerical method used for the solution of these equations is the second order accurate MacCormack explicit predictor-corrector scheme. The numerical results are compared to the experimental results of Yamamoto for the same C-D nozzle geometry and similar operating conditions. The goal of the study is to use numerical simulation techniques to resolve accurately physical processes which contribute to jet noise, and to assess whether performing these simulations in a three dimensional geometry is worth the additional cost in computing resources as compared to a comparable simulation on a two dimensional planar or axisymmetric geometry. Scientific visualization is used to observe the spreading characteristics of the jet, as well as to examine the structure of the shocks within the jet core. The time average velocity and turbulence intensity level at various locations are computed and compared with experimental results. A two point space-time cross correlation is used to compute the mean convection speed through the shear layer, and these predictions are compared with results from theory.

James N Scott↗
NASA NTRS1983

Feasibility study for a generalized gate logic software simulator

Unit-delay simulation, event driven simulation, zero-delay simulation, simulation techniques, 2-valued versus multivalued logic, network initialization, gate operations and alternate network representations, parallel versus serial mode simulation fault modelling, extension of multiprocessor systems, and simulation timing are discussed. Functional level networks, gate equivalent circuits, the prototype BDX-930 network model, fault models, identifying detected faults for BGLOSS are discussed. Preprocessor tasks, postprocessor tasks, executive tasks, and a library of bliss coded macros for GGLOSS are also discussed.

Mcgough, J. G.↗
NASA NTRS1984

Reliability and maintainability assessment factors for reliable fault-tolerant systems

A long term goal of the NASA Langley Research Center is the development of a reliability assessment methodology of sufficient power to enable the credible comparison of the stochastic attributes of one ultrareliable system design against others. This methodology, developed over a 10 year period, is a combined analytic and simulative technique. An analytic component is the Computer Aided Reliability Estimation capability, third generation, or simply CARE III. A simulative component is the Gate Logic Software Simulator capability, or GLOSS. The numerous factors that potentially have a degrading effect on system reliability and the ways in which these factors that are peculiar to highly reliable fault tolerant systems are accounted for in credible reliability assessments. Also presented are the modeling difficulties that result from their inclusion and the ways in which CARE III and GLOSS mitigate the intractability of the heretofore unworkable mathematics.

Bavuso, S. J.↗
NASA NTRS1989

Application of a vectorized particle simulation in high-speed near-continuum flow

An efficient particle simulation technique, developed for use on vector architecture based supercomputers for studying hypersonic rarefied gas flows is employed to simulate the complex wake generated by Mach six flow over a 10 deg half-angle wedge for freestream Reynolds numbers of 1780 and 3560. Data obtained are compared against higher Reynolds number experimental results. Simulations utilized as many as 10 to the 5th computational cells and 10 to the 7th simulated particles having power-law interaction potentials. A code performance of 1.8-2.4 microsec of Cray-2 CPU time to process a single particle per timestep is achieved. Diffuse adiabatic and isothermal wedge surface models are used in this investigation. Although the wedge geometry is two-dimensional, the simulation incorporates a width-wise direction, resulting in a three-dimensional computation.

Woronowicz, Michael S.↗
NASA NTRS1989

A Mach 6 external nozzle experiment with Argon-Freon exhaust simulation

A scramjet exhaust simulation technique for hypersonic wind tunnel testing has been developed. Mixtures of Argon and Freon correctly match the inviscid simulation parameters of Mach number, static-pressure ratio, and the ratio of specific heats at the combustor exit location; this simulation is accomplished at significantly reduced temperatures and without combustion. An investigation of nozzle parametrics in a Mach 6 freestream showed that the external nozzle ramp angle, the cowl trailing-edge angle, an external nozzle flow fence and the nozzle static-pressure ratio significantly affected the external nozzle thrust and pitching moment as measured by the integration of surface-pressure data. A comparison of Argon-Freon and air exhaust simulation showed that the external nozzle thrust and pitching moment were in error by roughly a factor of 2 using air due to the incorrect match of the ratio of specific heats. An assessment of two-dimensional Euler and Navier-Stokes codes for predicting external nozzle aerodynamic characteristics was made by comparing computed and experimental results.

Pittman, James L.↗
NASA NTRS2000

Influence of the Polysilicon Gate on the Random Dopant Induced Threshold Voltage Fluctuations in Sub 100 nm MOSFETS with Thin Gate Oxides

In this paper for the first time we study the influence of the polysilicon gate on the random dopant induced threshold voltage fluctuations in sub 100 nm MOSFETs with tunnelling gate oxides. This is done by using an efficient 3D 'atomistic' simulation technique described elsewhere. Devices with uniform channel doping and with low doped epitaxial channels have been investigated. The simulations reveale that the polysilicon gate is responsible for a substantial fraction of the threshold voltage fluctuations in both devices when the gate oxide is scaled to tunnelling thickness in the range of 1 - 2 nm.

Asenov, Asen↗