Search NASA⌕ Search

SEARCH · Search NASA

Results for “static testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

A heat flux sensor leveraging the transverse Seebeck effect in elemental antimony

Certain configurations of anisotropic single crystal materials can generate a thermoelectric voltage orthogonal to an induced temperature gradient. This phenomenon is known as the Transverse Seebeck Effect (TSE) and can be leveraged to fabricate simple and robust heat flux sensors. Only a small number of materials have been considered as TSE-based transducers and, among these, few have been developed into sensors with ruggedization against chemical and mechanical degradation. Here, we report on the fabrication and characterization of a rugged TSE-based heat flux sensor using prismatic antimony single crystals. The heat flux sensor was tested under static and dynamic heating scenarios. The sensor has a linear responsivity of 16.8 µV/(W/cm2) to heat fluxes spanning more than two orders of magnitude and a time constant of 4.4 s. The sensor’s response to localized heating, probed with a laser scanning technique, validated that the transduction mechanism is primarily the TSE by ruling out a sizable contribution from the conventional Seebeck effect. Finite element analysis corroborated that components used in the sensor package are the primary determinants of the time constant and the decrement of the responsivity from its theoretical maximum. Design principles that may be applied to elicit a faster transient response or higher responsivity are proposed. Furthermore, the results establish single crystal antimony as a promising transducer material for heat flux measurement systems and demonstrate potential effects of ruggedization on sensor performance.

36 MATERIALS SCIENCE↗

Method for the in-situ measurement of pH and alteration extent for aluminoborosilicate glasses using Raman spectroscopy.

Characterization of long-term processes occurring during alteration of aluminoborosilicate glasses is relevant for natural as well as man-made materials. Static dissolution tests are a common setup for such studies, but the obtained results and related errors are impacted by the frequency and protocol of samplings performed to determine release via solution analysis, e.g. ICP-OES. A non-invasive method was developed to continuously monitor glass alteration based on in-situ Raman spectrometry of the solution contained in the alteration vessel. The alteration of a benchmark glass, the environment assessment (EA) glass, for 7 days at 90 °C showed the pH and boron concentration results obtained from solution monitoring and ICP-OES quantification were similar to the pH and boron results obtained from chemometric modelling of the Raman spectra and within error of previously published results in similar conditions. The errors on altered amounts of glass based on B release were similar for both in-situ Raman and ICP-OES. The new Raman method provides a more detailed picture of real time monitoring of an alteration experiment, with intervals between monitoring times as short as dozens of seconds. The in-situ Raman method also helps to reduce perturbation to experiments caused by the physical sampling of aliquots (including temperature excursions, re-equilibration with atmosphere, volume variation, and potential chemical contamination) by limiting their number and frequency.

Parruzot, Benjamin PG↗

Transition Metal Dissolution in Lithium-Ion Cells: A Piece of the Puzzle

Static leaching tests were performed using the chemically delithiated positive electrode materials, LiFePO 4 , LiCoO 2 , LiMn 2 O 4 , LiNiO 2 , and LiNi 0.8 Mn 0.1 Co 0.1 O 2 . Instead of the common electrolyte, which contains LiPF 6 , the solvent consisted of only ethylene carbonate (EC) and ethyl methyl carbonate (EMC), limiting the possible reactions to only those that depend on the solvent. The product liquids from these experiments showed that there were lithium-bearing species in common, such as Li(EC) + and Li(EMC) + . Interestingly, we found evidence of electrolyte degradation products in both the positive-and negative-ion mass spectral results. The positive-ion results showed that the products tended to coordinate to lithium. In conclusion, the negative-ion results showed that most of the products tended to complex with transition metals. It was difficult to discern which positive ion was associated with which negative ion.

25 ENERGY STORAGE↗

Acrylic Triblock Copolymers Incorporating Isosorbide for Pressure Sensitive Adhesives

In this work, a new monomer acetylated acrylic isosorbide (AAI) was prepared in two steps using common reagents without the need for column chromatography. Free radical polymerization of AAI afforded poly(acetylated acrylic isosorbide) (PAAI), which exhibited a glass transition temperature ( T g ) = 95 °C and good thermal stability ( T d , 5% weight loss; N 2 = 331 °C, air = 291 °C). A series of ABA triblock copolymers with either poly( n -butyl acrylate) (PnBA) or poly(2-ethylhexyl acrylate) (PEHA) as the low T g midblocks and PAAI as the high T g end blocks were prepared using Reversible Addition–Fragmentation chain Transfer (RAFT) polymerization. The triblock copolymers ranging from 8–24 wt % PAAI were evaluated as pressure sensitive adhesives by 180° peel, loop tack, and static shear testing. While the PAAI-PEHA-PAAI series exhibited poor adhesive qualities, the PAAI-PnBA-PAAI series of triblock copolymers demonstrated peel forces up to 2.9 N cm –1 , tack forces up to 3.2 N cm –1 , and no shear failure up to 10 000 min. Dynamic mechanical analysis indicated that PAAI-PEHA-PAAI lacked the dissipative qualities needed to form an adhesive bond with the substrate, while the PAAI-PnBA-PAAI series exhibited a dynamic mechanical response consistent with related high performing PSAs.

2-Ethylhexyl acrylate↗

Accelerated Fill‐Up of the Arbuckle Group Aquifer and Links to U.S. Midcontinent Seismicity

The Arbuckle Group aquifer is the principal disposal zone for oil and gas field brines and hazardous/nonhazardous wastewater across the U.S. midcontinent and is traditionally viewed as an infinite capacity aquifer. Thousands of wells annually dispose hundreds of millions of barrels of wastewater into the aquifer across Kansas and Oklahoma, but direct links between injection and recent increases in seismicity have been hindered by a lack of pressure data for the Arbuckle Group. Here we present a newly compiled data set for 49 wells across Kansas that provides a unique perspective on the aquifer's performance over two decades. Statistical analysis of falloff test pressures, static fluid levels, and injection volumes shows that Arbuckle pressures and fluid levels are rising, recently at faster rates, likely associated with increased wastewater injection. The new data also suggest that the pressure diffusion, the primary driver of induced seismicity, can reach distances up to 25 km from an injection point and is connected to static fluid level rises. The compiled dataset explains the recent surge in midcontinent seismicity. The data set also suggests that the Arbuckle has finite storage capacity and that wastewater disposal across parts of the midcontinent may soon require alternatives.

58 GEOSCIENCES↗

Tin-based ionic chaperone phases to improve low temperature molten sodium–NaSICON interfaces

High temperature operation of molten sodium batteries impacts cost, reliability, and lifetime, and has limited the widespread adoption of these grid-scale energy storage technologies. Poor charge transfer and high interfacial resistance between molten sodium and solid-state electrolytes, however, prevents the operation of molten sodium batteries at low temperatures. In this study, in situ formation of tin-based chaperone phases on solid state NaSICON ion conductor surfaces is shown in this work to greatly improve charge transfer and lower interfacial resistance in sodium symmetric cells operated at 110 °C at current densities up to an aggressive 50 mA cm –2 . It is shown that static wetting testing, as measured by the contact angle of molten sodium on NaSICON, does not accurately predict battery performance due to the dynamic formation of a chaperone NaSn phase during cycling. This work demonstrates the promise of sodium intermetallic-forming coatings for the advancement of low temperature molten sodium batteries by improved mating of sodium–NaSICON surfaces and reduced interfacial resistance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Computational fluid dynamics and frequency-dependent finite-difference time-domain method coupling for the interaction between microwaves and plasma in rocket plumes

Under certain conditions during rocket flights, ionized exhaust plumes from solid rocket motors may interfere with radio frequency transmissions. To understand the relevant physical processes involved in this phenomenon and establish a prediction process for in-flight attenuation levels, we attempted to measure microwave attenuation caused by rocket exhaust plumes in a sea-level static firing test for a full-scale solid propellant rocket motor. The microwave attenuation level was calculated by a coupling simulation of the inviscid-frozen-flow computational fluid dynamics of an exhaust plume and detailed analysis of microwave transmissions by applying a frequency-dependent finite-difference time-domain method with the Drude dispersion model. The calculated microwave attenuation level agreed well with the experimental results, except in the case of interference downstream the Mach disk in the exhaust plume. It was concluded that the coupling estimation method based on the physics of the frozen plasma flow with Drude dispersion would be suitable for actual flight conditions, although the mixing and afterburning in the plume should be considered depending on the flow condition.

42 ENGINEERING↗

Microstructure and thermomechanical properties relationship of segmented thermoplastic polyurethane (TPU)

Thermoplastic polyurethanes (TPU) are important polymeric materials for seals. In competition with Acrylonitrile butadiene rubbers (NBR), TPU exhibits higher strength and a considerable better abrasion resistance. The advantage of NBR over TPU is a smaller compression set but however TPU excels in its much shorter processing cycle times. Generally a TPU is a block copolymer composed of hard and soft segments, which plays an important role in determining the material properties. TPU can be processed either to ready moulded parts or can be incorporated by multi component moulding, in both cases it shows decent mechanical properties. In the present work, the relationship between melt-process induced TPU morphology and resultant thermo mechanical properties were examined and determined by means of quasi-static tensile test, creep experiment, tension test and dynamical mechanical analysis (DMA). Scanning electron beam microscope (SEM) and differential scanning calorimeter (DSC) were used to study the morphology of the samples. A significant mathematical description of the stress-strain behaviour of TPU was found using a 3 term approach. Moreover it became evident that processing conditions such as processing temperature have crucial influence on morphology as well as short and long-term performance. To be more precise, samples processed at higher temperatures showed a lack of large hard segment agglomerates, a smaller strength for strains up to 250% and higher creep compliance.

36 MATERIALS SCIENCE↗

The use of thermovision technique to estimate the properties of highly filled polyolefins composites with calcium carbonate

The aim of this work was to determine the possibility of thermovision technique usage for estimating thermal properties of ternary highly filled composites (PE-MD/iPP/CaCO{sub 3}) and polymer blends (PE-MD/iPP) during mechanical measurements. The ternary, polyolefin based composites that contained the following amounts of calcium carbonate: 48, 56, and 64 wt % were studied. All materials were applying under tensile cyclic loads (x1, x5, x10, x20, x50, x100, x500, x1000). Simultaneously, a fully radiometric recording, using a TESTO infrared camera, was created. After the fatigue process, all samples were subjected to static tensile test and the maximum temperature at break was also recorded. The temperature values were analyzed in a function of cyclic loads and the filler content. The changes in the Young’s modulus values were also investigated.

36 MATERIALS SCIENCE↗

Interfacial enhancement of polypropylene composites modified with sorbitol derivatives and siloxane-silsesquioxane resin

Composites based on polypropylene (iPP) modified with a sorbitol derivative (NX8000) and siloxane-silsesquioxane resin (SiOPh) containing maleated polypropylene (MAPP) as compatibilizer were prepared by melt extrusion. Calorimetric investigations were carried out using differential scanning calorimetry (DSC), whereas the morphological and mechanical properties were investigated by scanning electron microscopy (SEM) and static tensile tests. DSC measurements revealed no influence of SiOPh and a slight effect of MAPP addition on the crystallization kinetics of polypropylene. Additionally, the introduction of MAPP into the iPP+NX8000+SiOPh composites increased plastic properties of the samples. All the above was attributed to the compatibilizing effect of MAPP which improved interfacial adhesion between iPP, NX8000 and SiOPh. This phenomenon was also confirmed by the SEM images illustrating more homogenous distribution of the filler in the compatibilized samples.

36 MATERIALS SCIENCE↗

A simple generalized gradient approximation for the noninteracting kinetic energy density functional

A simple, novel, non-empirical, constraint-based orbital-free generalized gradient approximation (GGA) non-interacting kinetic energy density functional is presented along with illustrative applications. The innovation is adaptation of constraint-based construction to the essential properties of pseudo-densities from the pseudo-potentials that are essential in plane-wave-basis ab initio molecular dynamics. This contrasts with constraining to the qualitatively different Kato-cusp-condition densities. The single parameter in the new functional is calibrated by satisfying Pauli potential positivity constraints for pseudo-atom densities. Finally, in static lattice tests on simple metals and semiconductors, the new LKT functional outperforms the previous best constraint-based GGA functional, VT84F (Phys. Rev. B 88, 161108(R) (2013)), is generally superior to a recently proposed meta-GGA, is reasonably competitive with parametrized two-point functionals, and is substantially faster.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Numerical relativity in spherical coordinates: A new dynamical spacetime and general relativistic MHD evolution framework for the Einstein Toolkit

We present SphericalNR, a new framework for the publicly available Einstein Toolkit that numerically solves the Einstein field equations coupled to the equations of general relativistic magnetohydrodynamic (GRMHD) in a 3+1 split of spacetime in spherical coordinates without symmetry assumptions. The spacetime evolution is performed using reference-metric versions of either the Baumgarte-Shapiro-Shibata-Nakamura equations or the fully covariant and conformal Z4 system with constraint damping. We have developed a reference-metric version of the Valencia formulation of GRMHD with a vector potential method, guaranteeing the absence of magnetic monopoles during the evolution. In our framework, every dynamical field (both spacetime and matter) is evolved using its components in an orthonormal basis with respect to the spherical reference metric. Furthermore, all geometric information about the spherical coordinate system is encoded in source terms appearing in the evolution equations. This allows for the straightforward extension of Cartesian high-resolution shock-capturing finite volume codes to use spherical coordinates with our framework. To this end, we have adapted GRHydro, a Cartesian finite volume GRMHD code already available in the Einstein Toolkit, to use spherical coordinates. We present the full evolution equations of the framework, as well as details of its implementation in the Einstein Toolkit. Finally, we validate SphericalNR by demonstrating it passes a variety of challenging code tests in static and dynamical spacetimes.

79 ASTRONOMY AND ASTROPHYSICS↗

Multiple-relaxation-time color-gradient lattice Boltzmann model for simulating two-phase flows with high density ratio

In this paper, we propose a color-gradient lattice Boltzmann (LB) model for simulating two-phase flows with high density ratio and high Reynolds number. The model applies a multi-relaxation-time (MRT) collision operator to enhance the stability of the simulation. A source term, which is derived by the Chapman-Enskog analysis, is added into the MRT LB equation so that the Navier-Stokes equations can be exactly recovered. Also, a new form of the equilibrium density distribution function is used to simplify the source term. To validate the proposed model, steady flows of a static droplet and the layered channel flow are first simulated with density ratios up to 1000. Small values of spurious velocities and interfacial tension errors are found in the static droplet test, and improved profiles of velocity are obtained by the present model in simulating channel flows. Then, two cases of unsteady flows, Rayleigh-Taylor instability and droplet splashing on a thin film, are simulated. In the former case, the density ratio of 3 and Reynolds numbers of 256 and 2048 are considered. The interface shapes and spike/bubble positions are in good agreement with the results of previous studies. In the latter case, the droplet spreading radius is found to obey the power law proposed in previous studies for the density ratio of 100 and Reynolds number up to 500.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Seeded Stage III glass dissolution behavior of a statistically designed glass matrix

The glass dissolution rate of some glasses accelerates after prolonged time spent at a slow, residual glass dissolution rate. This phenomenon is referred to as Stage III behavior. Here, the acceleration in glass dissolution rate linked to Stage III behavior is significant and may be the most impactful to long-term performance of glass in a repository. This work is aimed at understanding the effect of glass composition on Stage III behavior to add a level of technical defensibility to glass disposal. To this end, a set of twenty-four glass compositions were statistically designed, where eight glass components (SiO 2 , B 2 O 3 , Al 2 O 3 , CaO, Na 2 O, SnO 2 , ZrO 2 , and Others) have been independently varied in order to study the individual effects of each. These glasses have been subjected to static dissolution tests at 90 °C in deionized water and then seeded with zeolite Na-P2 28 days into the testing to induce Stage III behavior. The response of the glasses to the zeolite seeds fell into four primary types: 1) no response to seeds; 2) an immediate linear sustained acceleration in the rate; 3) an immediate linear acceleration in the rate followed by a decrease; and, 4) a progressive acceleration in the rate that is concurrent with the addition of the seeds. The main glass components observed to influence these behaviors were CaO, Al 2 O 3 , B 2 O 3 , and ZrO 2 , where: 1) CaO influenced which glasses showed a Stage III response to seeds (high CaO: Types 2, 3, and 4) or did not respond to seeds (low CaO: Type 1), 2) Al 2 O 3 and B 2 O 3 influenced which glasses showed a sustainable Stage III response (high Al 2 O 3 : Types 2 and 4) versus transitory response (low Al 2 O 3 and high B 2 O 3 : Type 3), and 3) ZrO 2 concentration influenced whether glasses showed a linear (high ZrO 2 : Type 2) versus progressive (low ZrO 2 : Type 4) response to seeds.

36 MATERIALS SCIENCE↗

A Co-Registered In-Situ and Ex-Situ Tensile Properties Dataset from a Laser Powder Bed Fusion Additive Manufacturing Process (Peregrine v2023-11)

This release contains a co-registered in-situ and ex-situ Peregrine dataset from five Concept Laser M2 Laser Powder Bed Fusion (L-PBF) stainless steel 316L builds containing 6,299 SS-J3 individually tracked tensile coupons. These data were collected at the Manufacturing Demonstration Facility (MDF) located at Oak Ridge National Laboratory (ORNL). The dataset includes layer-wise visible-light in-situ imaging data, the laser scan paths and parameters, in-situ temporal sensor data, room-temperature static tensile test results, and the target part geometries. Additionally, anomaly detections produced by a modified Dynamic Segmentation Convolutional Neural Network (DSCNN) are provided.

36 MATERIALS SCIENCE↗

Designing an impedance-based technique for studying corrosion on cladding materials

In nuclear cladding materials, changes in structure and chemistry over the lifetime of claddings can have a significant impact on fuel and reactor performance. Currently, chemical evolution over the lifetime of the fuel and cladding materials can only be inferred using post-irradiation examination. As an alternative to post-irradiation measurements, electrochemical impedance spectroscopy (EIS) can provide an in-pile measurement of changes in chemistry in oxides and hydrides. The objective of this study is to develop an impedance based sensing technology for measuring spatial- and time-resolved in-pile changes in cladding chemistry in order to understand the mechanisms of hydride formation, hydride dealloying and associated cladding corrosion so that a mitigation strategy and technology can be developed for reactor safe operation. Two prototype impedance-based sensors were designed and assembled using Zr-4 as working electrode and Pt as counter and reference electrode. One sensor is tubular type and the other one is plate-type. These sensors will be tested in static autoclave to investigate the effects of various environmental conditions (including temperature, pressure, and water chemistry) on cladding material corrosion mechanisms. These in-situ EIS sensors would provide corrosion-layer parameters in high-temperature water, such as (1) total layer thickness, (2) the evolution of oxide structures as uniform layer dielectric or sublayer(s), and (3) the possible electrochemistry of the volume corrosion process and the solid/liquid interface, such as the cyclic nature of corrosion of Zr alloys in high-temperature water. This work was focused on electrochemical sensor development, targeting cladding oxides/hydrides under thermodynamic equilibria; characterization of samples using Kelvin probe force microscopy (SKPFM), Raman spectroscopy, and scanning electron microscopy (SEM) with energy-dispersive X-ray spectroscopy (EDS) to provide high-resolution co-localized characterization of zirconium oxide and metal/oxide interface.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗