Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface layering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10

Anomalous behavior of the atmospheric surface layer over a melting snowpack

During March, 1978 on a snow-covered field near Lee Vining, California, measurements were made that included: (1) variations above the snow surface of the net radiative flux and the profile of wind speed, air temperature and relative humidity; and (2) variations beneath the snow surface of the conductive heat flux and the temperature profile. The period was marked by clear skies, warm air and calm winds during the day, and cold air and moderate winds at night. During the day, a highly stable sublayer formed near the surface, with a persistent warm layer at approximately 0.5 m above the surface. At night, profiles agreed more with classical log-linear forms found in stable air. Numerical simulation of long and shortwave radiative fluxes near the surface, using observed humidity profiles, produced the daytime warm level in agreement with observations. It was concluded that in the absence of turbulent mixing, strong solar radiation and a supply of moisture from the snow will cause a raised maximum of temperature during the day.

Halberstam, I.↗

Boron–oxygen complex yields n-type surface layer in semiconducting diamond

Diamond is a wide-bandgap semiconductor possessing exceptional physical and chemical properties with the potential to miniaturize high-power electronics. Whereas boron-doped diamond (BDD) is a well-known p-type semiconductor, fabrication of practical diamond-based electronic devices awaits development of an effective n-type dopant with satisfactory electrical properties. Here we report the synthesis of n-type diamond, containing boron (B) and oxygen (O) complex defects. We obtain high carrier concentration (~0.778 × 10 21 cm -3 ) several orders of magnitude greater than previously obtained with sulfur or phosphorous, accompanied by high electrical conductivity. In high-pressure high-temperature (HPHT) boron-doped diamond single crystal we formed a boron-rich layer ~1–1.5 μm thick in the {111} surface containing up to 1.4 atomic % B. We show that under certain HPHT conditions the boron dopants combine with oxygen defects to form B–O complexes that can be tuned by controlling the experimental parameters for diamond crystallization, thus giving rise to n-type conduction. First-principles calculations indicate that B 3 O and B 4 O complexes with low formation energies exhibit shallow donor levels, elucidating the mechanism of the n-type semiconducting behavior.

36 MATERIALS SCIENCE↗

Thermocapillary flows and their stability: Effects of surface layers and contamination

The fluid mechanics and heat transfer of motions driven by surface tension gradients (Marangoni convection) were analyzed theoretically to obtain an understanding of the convection accompanying the process of growing high quality single crystals from the melt in a mu-g environment. The geometries considered include two dimensional liquid filled slots and axisymmetric float zone configurations.

Davis, S. H.↗

Patterns of Canopy and Surface Layer Consumption in a Boreal Forest Fire from Repeat Airborne Lidar

Fire in the boreal region is the dominant agent of forest disturbance with direct impacts on ecosystem structure, carbon cycling, and global climate. Global and biome-scale impacts are mediated by burn severity, measured as loss of forest canopy and consumption of the soil organic layer. To date, knowledge of the spatial variability in burn severity has been limited by sparse field sampling and moderate resolution satellite data. Here, we used pre- and post-fire airborne lidar data to directly estimate changes in canopy vertical structure and surface elevation for a 2005 boreal forest fire on Alaskas Kenai Peninsula. We found that both canopy and surface losses were strongly linked to pre-fire species composition and exhibited important fine-scale spatial variability at sub-30m resolution. The fractional reduction in canopy volume ranged from 0.61 in lowland black spruce stands to 0.27 in mixed white spruce and broad leaf forest. Residual structure largely reflects standing dead trees, highlighting the influence of pre-fire forest structure on delayed carbon losses from above ground biomass, post-fire albedo, and variability in understory light environments. Median loss of surface elevation was highest in lowland black spruce stands (0.18 m) but much lower in mixed stands (0.02 m), consistent with differences in pre-fire organic layer accumulation. Spatially continuous depth-of-burn estimates from repeat lidar measurements provide novel information to constrain carbon emissions from the surface organic layer and may inform related research on post-fire successional trajectories. Spectral measures of burn severity from Landsat were correlated with canopy (r = 0.76) and surface (r = -0.71) removal in black spruce stands but captured less of the spatial variability in fire effects for mixed stands (canopy r = 0.56, surface r = -0.26), underscoring the difficulty in capturing fire effects in heterogeneous boreal forest landscapes using proxy measures of burn severity from Landsat.

Alonzo, Michael↗

Production Rates of Noble Gases in the Near-Surface Layers of Europa by Energetic Charged Particles and the Potential for Determining Exposure Ages

The surface of Europa is expected to be extremely active, undergoing tectonic and/or tidal geological activity and sputtering/ deposition, as well as impact cratering. Determination of the actual age of the surface at one or more places would greatly simplify trying to sort out what processes are occurring, and at what rate. If there is K present, as the spectral and compositional modeling discussed predict, it should be possible, in principle, to determine K-Ar crystallization ages. Whether or not there is K present, a consideration of the environment suggests we can determine an energetic particle exposure age if we can make in situ measurements of the abundances of major elements and of noble gas isotopes. This requires instrumentation that is within reach of current technology. In this paper, we calculate production rates for noble-gas isotopes in a simplified Europan surface, to quantify the amount of light noble gases produced by exposure to energetic particles.

Swindle, T. D.↗

Nonequilibrium structural condition in the medical TiNi-based alloy surface layer treated by electron beam

The research is devoted to study the structural condition and their evolution from the surface to the depth of TiNi specimens treated by low-energy high-current electron beams with surface melting at a beam energy density E = 10 J/cm{sup 2}, number of pulses N = 10, and pulse duration τ = 50 μs. Determined thickness of the remelted layer, found that it has a layered structure in which each layer differs in phase composition and structural phase state. Refinement B2 phase lattice parameters in local areas showed the presence of strong inhomogeneous lattice strain.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Carbides composite surface layers produced by (PTA)

The plasma transferred arc technique was applied to deposit a composite layer of nickel base with tungsten carbide in powder form on to surface of low alloy steel 18G2A type according to polish standard. Results showed that, plasma transferred arc hard facing process was successfully conducted by using Deloro alloy 22 plus tungsten carbide powders. Maximum hardness of 1489 HV and minimum dilution of 8.4 % were achieved by using an arc current of 60 A. However, when the current was further increased to 120 A and the dilution increases with current increase while the hardness decreases. Microstructure of the nickel base deposit with tungsten carbide features uniform distribution of reinforcement particles with regular grain shape half - dissolved in the matrix.

36 MATERIALS SCIENCE↗

Diurnal variations of the Martian surface layer meteorological parameters during the first 45 sols at two Viking Lander sites

Wind speed, ambient and surface temperatures from both Viking Landers have been used to compute bulk Richardson numbers and Monin-Obukhov lengths during the earliest phase of the Mars missions. These parameters are used to estimate drag and heat transfer coefficients, friction velocities and surface heat fluxes at the two sites. The principal uncertainty is in the specification of the roughness length. Maximum heat fluxes occur near local noon at both sites, and are estimated to be in the range 15-20 W/sq m at the Viking 1 site and 10-15 W/sq m at the Viking 2 site. Maximum values of friction velocity occur in late morning at Viking 1 and are estimated to be 0.4-0.6 m/s. They occur shortly after dawn at the Viking 2 site where peak values are estimated to be in the range 0.25-0.35 m/s. Extension of these calculations to later times during the mission will require allowance for dust opacity effects in the estimation of surface temperature and in the correction of radiation errors of the Viking 2 temperature sensor.

Sutton, J. L.↗

Thermocapillary flows and their stability: Effects of surface layers and combination

The theoretical analysis of the fluid mechanics and heat transfer of motions driven by surface tension gradients (Marangoni convection) was researched. Convection accompanying the process of growing high quality single crystals from the melt in a micro-g environment was examined. The geometries considered include two dimensional liquid filled slots and axisymmetric float-zone configurations.

Davis, S. H.↗

Modeling of Turbulent Boundary Layer Surface Pressure Fluctuation Auto and Cross Spectra - Verification and Adjustments Based on TU-144LL Data

The literature on turbulent boundary layer pressure fluctuations provides several empirical models which were compared to the measured TU-144 data. The Efimtsov model showed the best agreement. Adjustments were made to improve its agreement further, consisting of the addition of a broad band peak in the mid frequencies, and a minor modification to the high frequency rolloff. The adjusted Efimtsov predicted and measured results are compared for both subsonic and supersonic flight conditions. Measurements in the forward and middle portions of the fuselage have better agreement with the model than those from the aft portion. For High Speed Civil Transport supersonic cruise, interior levels predicted by use of this model are expected to increase by 1-3 dB due to the adjustments to the Efimtsov model. The space-time cross-correlations and cross-spectra of the fluctuating surface pressure were also investigated. This analysis is an important ingredient in structural acoustic models of aircraft interior noise. Once again the measured data were compared to the predicted levels from the Efimtsov model.

Rackl, Robert↗

Structure and Properties of Zn-Implanted Si Near-Surface Layer Modification Depending on Irradiation Fluence of {sup 132}Xe{sup 26+} Ions with Energy of 167 MeV

Single-crystal n-Si(100) wafers are implanted with {sup 64}Zn{sup +} ions with an energy of 50 keV and dose of 5 × 10{sup 16} cm{sup –2}. Then the samples are irradiated with {sup 132}Xe{sup 26+} ions with an energy of 167 MeV in the range of fluences from 1 × 10{sup 12} to 5 × 10{sup 14} cm{sup –2}. The surface and cross section of the samples are visualized by scanning electron microscopy and transmission electron microscopy. The distribution of implanted Zn atoms is studied by time-of-flight secondary-ion mass spectrometry. After irradiation with Xe, surface pores and clusters consisting of a Zn–ZnO mixture are observed at the sample surface. In the amorphized subsurface Si layer, zinc and zinc-oxide phases are detected. After irradiation with Xe with a fluence of 5 × 10{sup 14} cm{sup –2}, no zinc or zinc-oxide clusters are detected in the samples by the methods used in the study.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A UNIFIED MONTE CARLO TREATMENT OF GAS-GRAIN CHEMISTRY FOR LARGE REACTION NETWORKS. II. A MULTIPHASE GAS-SURFACE-LAYERED BULK MODEL

The observed gas-phase molecular inventory of hot cores is believed to be significantly impacted by the products of chemistry in interstellar ices. In this study, we report the construction of a full macroscopic Monte Carlo model of both the gas-phase chemistry and the chemistry occurring in the icy mantles of interstellar grains. Our model treats icy grain mantles in a layer-by-layer manner, which incorporates laboratory data on ice desorption correctly. The ice treatment includes a distinction between a reactive ice surface and an inert bulk. The treatment also distinguishes between zeroth- and first-order desorption, and includes the entrapment of volatile species in more refractory ice mantles. We apply the model to the investigation of the chemistry in hot cores, in which a thick ice mantle built up during the previous cold phase of protostellar evolution undergoes surface reactions and is eventually evaporated. For the first time, the impact of a detailed multilayer approach to grain mantle formation on the warm-up chemistry is explored. The use of a multilayer ice structure has a mixed impact on the abundances of organic species formed during the warm-up phase. For example, the abundance of gaseous HCOOCH{sub 3} is lower in the multilayer model than in previous grain models that do not distinguish between layers (so-called two phase models). Other gaseous organic species formed in the warm-up phase are affected slightly. Finally, we find that the entrapment of volatile species in water ice can explain the two-jump behavior of H{sub 2}CO previously found in observations of protostars.

79 ASTRONOMY AND ASTROPHYSICS↗

On the inhomogeneity of the transition surface layer of the solid core of the earth

Different geophysical data and conclusions of theoretical models, which can give information about the behavior of the solid and liquid cores of the Earth as well as about the existence of a transition layer as a temperature-hysteresis region at a relatively weak first-order phase transition, are compared. It is concluded that liquid inclusions inevitably exist in this region; these inclusions are involved (due to the complex convective processes occurring in the liquid core) in the transport of light materials from some areas of the solid-core surface. The porosity and permeability of the transition layer determine the seismic acoustic inhomogeneities in these areas, which contact the convective flows in the liquid core. In particular, this explains the well-known 'east-west' effect. Obviously, the model of the crystalline core is not the only possible alternative for a model of a core with a metallic glasslike structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Formation of porous surface layers in reaction bonded silicon nitride during processing

Microstructural examination of reaction bonded silicon nitride (RBSN) has shown that there is often a region adjacent to the as-nitrided surfaces that is even more porous than the interior of this already quite porous material. Because this layer of large porosity is considered detrimental to both the strength and oxidation resistance of RBSN, a study was undertaken to determine if its formation could be prevented during processing. All test bars studied were made from a single batch of Si powder which was milled for 4 hours in heptane in a vibratory mill using high density alumina cylinders as the grinding media. After air drying the powder, bars were compacted in a single acting die and hydropressed.

Shaw, N. J.↗

The influence of MoO{sub x} gap states on hole injection from aluminum doped zinc oxide with nanoscale MoO{sub x} surface layer anodes for organic light emitting diodes

The effective workfunction of Al doped ZnO films (AZO) increased from 4.1 eV to 5.55 eV after surface modification with nanoscale molybdenum sub-oxides (MoO{sub x}). Hole only devices with anodes consisting of 3 nm of MoO{sub x} on AZO exhibited a lower turn-on voltage (1.5 vs 1.8 V), and larger charge injection (190 vs 118 mA/cm{sup 2}) at the reference voltage, compared to indium tin oxide (ITO). AZO devices with 10 nm of MoO{sub x} exhibited the highest workfunction but performed poorly compared to devices with 3 nm of MoO{sub x}, or standard ITO. Ultraviolet photoelectron, X-ray photoelectron, and optical spectroscopies indicate that the 3 nm MoO{sub x} films are more reduced and farther away from MoO{sub 3} stoichiometry than their 10 nm equivalents. The vacancies associated with non-stoichiometry result in donor-like gap states which we assign to partially occupied Mo 4d levels. We propose that Fowler-Nordheim tunneling from these levels is responsible for the reduction in threshold voltage measured in devices with 3 nm of MoO{sub x}. A schematic band diagram is proposed. The thicker MoO{sub x} layers are more stoichiometric and resistive, and the voltage drop across these layers dominates their electrical performance, leading to an increase in threshold voltage. The results indicate that AZO with MoO{sub x} layers of optimal thickness may be potential candidates for anode use in organic light emitting diodes.

36 MATERIALS SCIENCE↗

Efficient photoelectric converters of ultraviolet radiation based on ZnS and CdS with low-resistivity surface layers

The formation of thin high- and low-resistivity layers in the space-charge region of Cu{sub 1.8}S-CdS and Cu{sub 1.8}S-ZnS surface-barrier photoconverter structures leads to a considerable increase in photosensitivity and a reduction in the dark tunneling-recombination currents. Highly efficient and stable ultraviolet photoconverters based on CdS and ZnS were obtained, and their electrical and photoelectrical properties were studied. The main operational parameters of the photoconverters are reported.

36 MATERIALS SCIENCE↗