SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Liquid surface observed through metal container wall, allowing direct determination of quantities and changes. X-ray measurement of liquid level produces photograph in which liquid appears as solid dark mass. Commercially-available portable X-ray machine is used.
The Huygens Probe of the Cassini Huygens Mission entered the atmosphere of the moon Titan on January 14, 2005. The GCMS was part of the instrument complement on the probe to measure in situ the chemical composition of the atmosphere during the probe descent and to support the Aerosol Collector Pyrolyzer (ACP) experiment by serving as detector for the pyrolization products. The GCMS collected data from an altitude of 146 km to ground impact for a time interval of 2hours and 37minutes. The Probe and the GCMS survived the ground impact and collected data for 1hour and 9 minutes on the surface in the near surface environment until signal loss by the orbiter. The major constituents of the lower atmosphere were found to be N2 and CH4. The methane-mixing ratio was found to increase below the turbopause, about 35 km altitude, monotonically toward the surface to levels near saturation. After surface impact a steep increase of the mixing ratio was observed suggesting evaporation of surface condensed methane due to heating by the GCMS sample inlet heater. Other constituents were found to be in very low concentrations, below ppm levels. The presence of Argon 40 was confirmed. The results for the other noble gases are still being evaluated. Other hydrocarbons and nitriles were also observed and quantitative evaluation is in progress. Preliminary ratios for the major carbon and nitrogen isotopes were computed from methane and molecular nitrogen measurements. The instrument collected 5634 mass spectra during descent and 2692 spectra on the ground over a range of m/z from 2 to 141. Eight gas chromatograph samples were taken during the descent and two on the ground.
The Huygens Probe of the Cassini Huygens Mission entered the atmosphere of the moon Titan on January 14, 2005. The GCMS was part of the instrument complement on the Probe to measure in situ the chemical composition of the atmosphere during the probe descent and to support the Aerosol Collector Pyrolyzer (ACP) experiment by serving as detector for the pyrolization products. The GCMS collected data from an altitude of 146 km to ground impact for a time interval of 2 hours and 37 minutes. The Probe and the GCMS survived the ground impact and collected data for 1 hour and 9 minutes on the surface in the near surface environment until signal loss by the orbiter. The instrument collected 5634 mass spectra during descent and 2692 spectra on the ground over a range of m/z from 2 to 141. Eight gas chromatograph samples were taken during the descent and two on the ground. This is a report on work in progress. The major constituents of the lower atmosphere were found to be N2 and CH4. The methane-mixing ratio was found to increase below the turbopause, about 35 km altitude, monotonically toward the surface to levels near saturation. After surface impact a steep increase of the mixing ratio was observed suggesting evaporation of surface condensed methane due to heating by the GCMS sample inlet heater. Other constituents were found to be in very low concentrations, below ppm levels. The presence of Argon 40 was confirmed. The results for the other noble gases are still being evaluated. Other hydrocarbons and nitriles were also observed and quantitative evaluation is in progress. Preliminary ratios for the major carbon and nitrogen isotopes were computed from methane and molecular nitrogen measurements.
Although it is fairly well established that information about surface layout can be gained from motion cues, it is not so clear as to what information humans can use and what specific information they should be provided. Theoretical analyses tell us that the information is in the stimulus. It will take more experiments to verify that this information can be used by humans to extract surface layout from the 2D velocity flow field. The visual motion factors that can affect the pilot's ability to control an aircraft and to infer the layout of the terrain ahead are discussed.
The station data of monthly mean sea level pressure, surface air temperature as well as monthly mean upper air rawinsonde observations were used to study the trends in the southern winter (June, July and August) and summer (December, January and February). This study covers the period 1951 to 1981. Most of the surface data have continuous 31 year records, however, for some high latitude stations, both surface and upper air records started in 1957 or even later. The normalized anomaly for a given variable Z is defined as the departure from the 1951 to 1981 grand mean divided by the standard deviation during the same period. To eliminate the large fluctuations in the data, the 1-3-1 smoothing was applied to the time series of normalized anomalies. The trends of monthly mean temperatures and height from the surface to 200 mb level is documented.
The Tropical Ocean Global Atmosphere (TOGA) Program is a component of the World Meteorological Organization (WMO)/International Council of Scientific Unions (ICSU) World Climate Research Program (WCRP). One of the objectives of TOGA, which began in 1985, is to determine the limits of predictability of monthly mean sea surface temperature variations in tropical regions. The TOGA program created a raison d'etre for an explosive growth of the tropical ocean observing system and a substantial improvement in numerical simulations from atmospheric and oceanic general circulation models. Institutions located throughout the world are involved in the TOGA-distributed active data archive system. The diverse TOGA data sets for 1985 and 1986, including results from general circulation models, are included on a CD-ROM. Variables on the CD-ROM are barometric pressure, surface air temperature, dewpoint temperature Cartesian components of surface wind, surface sensible and latent heat fluxes,Cartesian components of surface wind stress and of an index of surface wind stress, sea level, sea surface temperature, and depth profiles of temperature and current in the upper ocean. Some data sets are global in extent, some are regional and cover portions of an ocean basin. Data on the CD-ROM can be extracted with an Apple Macintosh or an IBM PC.
In this work, the impact of Los Angeles Basin pollution transport and stratospheric intrusions on the surface ozone levels observed in the San Gabriel Mountains is investigated based on a combination of surface and lidar measurements as well as WRF-Chem (Weather Research and Forecasting with Chemistry) and WACCM (Whole Atmosphere Community Climate Model) runs. The number of days with observed surface ozone levels exceeding the National Ambient Air Quality Standards exhibit a clear seasonal pattern, with a maximum during summer, when models suggest a minimum influence of stratospheric intrusions and the largest impact from Los Angeles Basin pollution transport. Additionally, measured and modeled surface ozone and PM10 were analyzed as a function of season, time of the day, and wind direction. Measurements and models are in good qualitative agreement, with maximum surface ozone observed for southwest and west winds. For the prevailing summer wind direction, slightly south of the ozone maximum and corresponding to south-southwest winds, lower ozone levels were observed. Back trajectories suggest that this is associated with transport from the central Los Angeles Basin, where titration limits the amount of surface ozone. A quantitative comparison of the lidar profiles with WRF-Chem and WACCM models revealed good agreement near the surface, with models showing an increasing positive bias as function of altitude, reaching 75 % at 15 km above sea level. Finally, three selected case studies covering the different mechanisms affecting the near-surface ozone concentration over the San Gabriel Mountains, namely stratospheric intrusions and pollution transport, are analyzed based on surface and ozone lidar measurements, as well as co-located ceilometer measurements and models.
With NASA’s goal of returning humans to the Moon, it has become increasingly important to understand the impact of lunar regolith on spacecraft systems. The ability to measure the level of dust coverage on a surface is essential. Developing an accurate technique to determine percent area coverage is challenging due to the unique and complex layering of the dust particles on the surface, creating fairy castle structures that form complex towers, bridges, and buttresses using the smallest of dust particles as building blocks. For this study, these structures have been simulated using a unique dust distributor device and imaged with a scanning electron microscope. The results show the dusted surface’s complex topology, thus demonstrating the difficulty with determining the percent area of dust coverage. Implications for dust buildup on spacecraft, even at the microscopic level, can include degraded heat transfer and altered optical properties, making continuation of this research critical to support future human exploration of the Moon.
Heated surface orientation and reduced gravity effects on Freon 113 nucleate
Our program includes five research items: (1) determination of a precision geoid and gravity anomaly field; (2) precise leveling and detection of tidal changes of the sea surface and study of the role of the tide in the global energy exchange; (3) oceanic effect on the Earth's rotation and polar motion; (4) geological and geophysical interpretation of the altimetry gravity field; and (5) evaluation of the effectiveness of local tracking of TOPEX/POSEIDON by use of a laser tracker.
Vortex phenomena encountered in an investigation of the streamwise development of the three-dimensional wake region behind the tip of a three-dimensional wedge model are reported. Pressure profiles were measured by pitot probes downstream of a tip with a nearly constant surface pressure level and a nearly continuous surface curvature in a blowdown air tunnel operating at Mach 6. Rather than the simple three-dimensional quasi-parallel shear flow expected, the measurements indicated the presence of a flow with large deficits in longitudinal pitot pressure, which are usually associated with the core region of quasi-steady longitudinal vortices. Vapor screen flow visualizations also support the presence of longitudinal vortices located primarily in the tip region and evidently forming in the vicinity of the wake neck. An increase in overall wake thickness by 100% is also observed. The origin of the vortices as quasi-steady Taylor-Gortler vortices generated in the concavely curved shear layer near the wake neck is considered. It is pointed out that the existence of longitudinal vortexes suggests that three-dimensional turbulence modeling may be much more difficult than previously supposed.
PM2.5, particulate matter (PM) with a diameter less than or equal to 2.5 μm, is emitted from anthropogenic fuel combustion and forest fires. Due to their small size, PM2.5 can penetrate into respiratory systems and cause or exacerbate serious illness. The US Environmental Protection Agency (EPA) regulates the levels of surface PM2.5 but surface monitoring has spatial and temporal limitations. The Aerosol Optical Depth (AOD) retrievals from the Geostationary Operational Environmental Satellite (GOES) missions and meteorological factors can be utilized as an alternative technique to estimate surface PM2.5 levels at a higher spatial and temporal resolution compared to surface monitors. Traditional estimation approaches rely on linear regression techniques and have limitations modeling the nonlinear relationship between the meteorological factors, AOD retrievals, and surface PM2.5. We compare different machine learning techniques and identify the best-suited model that can represent the nonlinearity between the factors affecting PM2.5 levels
IUE far-UV and Einstein Observatory soft X-ray observations for the red giant Arcturus and the nearby yellow dwarf Alpha-Centauri A, which are archetypes of solar mass stars in different stages of evolution, are compared. Evidence is found for neither coronal soft X-ray emission from the red giant, at surface flux levels of only 0.0006 that detected previously for the yellow dwarf, nor C II and IV resonance line emission at surface flux levels of only 0.02 those of the yellow dwarf. The resonance line upper limits and previous detections of the C II intersystem UV multiplet 0.01 near 2325 A provide evidence for an Arcturus outer atmosphere that is geometrically extended, tenuous and cool. The red giant has, in addition, a prominent cool stellar wind. An extensive tabulation of line identifications, widths and fluxes for the IUE far-UV echelle spectra of the two stars is given, and two competing explanations for the Wilson-Bappu effect are discussed.
This report provides an assessment of Version 4 of the SMAP Level 4 Surface and Root Zone Soil Moisture (L4_SM) product, released on 14 June 2018. The assessment includes comparisons of L4_SM soil moisture and temperature estimates with in situ measurements from core validation sites and sparse networks. The assessment further includes a global evaluation of the internal diagnostics from the ensemble-based data assimilation system that is used to generate the L4_SM product, including observation-minus-forecast (O-F) brightness temperature residuals and soil moisture analysis increments.Together, the core validation site comparisons and the statistics of the assimilation diagnostics areconsidered primary validation methodologies for the L4_SM product. Comparisons against in situ measurements from regional-scale sparse networks are considered a secondary validation methodology because such in situ measurements are subject to upscaling errors from the point-scale to the grid-cell scale of the data product.The Version 4 L4_SM product benefits from an improved land surface modeling system and from retrospective surface meteorological forcing data that are as consistent as possible with the present-day datain terms of their climatology. Specifically, the model changes include revised parameters and parameterizations for (i) the surface energy balance, (ii) recharge from below of the model's surface excess reservoir, and (iii) the snow depletion curve. Updated ancillary inputs include improved datasets for landcover, topography, and vegetation height. The Version 4 algorithm further includes a revised approach to precipitation corrections that improves the precipitation climatology in Africa and the high-latitudes. Moreover, for system calibration the model is forced retrospectively with MERRA-2 reanalysis data, which are more consistent with the near-real time GEOS forward processing (FP) data used during the SMAP period than the retrospective GEOS data that were available for previous L4_SM versions. An analysis of the time-average surface and root zone soil moisture shows that the global pattern ofarid and humid regions is captured by the Version 4 L4_SM estimates. Owing to the changes in the landsurface modeling system, surface soil moisture is typically drier by several volumetric percent in Version 4 compared to Version 3, whereas root zone soil moisture is wetter in Version 4 in some regions and drierin others. Because of these climatological differences, the Version 3 and Version 4 products should not be combined into a single dataset for use in applications.Results from the core validation site comparisons indicate that Version 4 of the L4_SM data product meets the self-imposed L4_SM accuracy requirement, which is formulated in terms of the RMSE after removal of the long-term mean difference (ubRMSE). The overall ubRMSE of the 3-hourly L4_SM dataat the 9 km scale is 0.039 m3 m-3 for surface soil moisture and 0.029 m3 m-3 for root zone soil moisture,below the 0.04 m3 m-3 requirement. The L4_SM estimates are an improvement over estimates from a model-only Nature Run version 7.2 (NRv7.2), which demonstrates the beneficial impact of the SMAP brightness temperature data. Overall, L4_SM surface and root zone soil moisture estimates are more skillful than NRv7.2 estimates, with statistically significant improvements at the 5% level for surface soil moisture R and anomaly R values. Results from comparisons of the L4_SM product to i
Peening techniques like laser peening and shot peening were used to modify the surface of friction stir welded 7075-T7351 Aluminum Alloy specimens. The tensile coupons were machined such as the loading was applied in a direction perpendicular to the weld direction. The peening effects on the global and local mechanical properties through the different regions of the weld were characterized and assessed. The surface hardness levels resulting from various peening techniques were also investigated for both sides of the welds. Shot peening resulted in an increase to surface hardness levels, but no improvement was noticed on the mechanical properties. In contrast, mechanical properties were improved by laser peening when compared to the unpeened material.
November 27, 2007 marks the l0th anniversary of the launch of the Tropical Rainfall Measuring Mission (TRMM) satellite. In anticipation of this anniversary, this paper will present an overview of the various TRMM data products currently available including the standard products, near real-time products, special products, and prototype products. It also will present an easy way to obtain these data. TRMM standard products have been publicly available since a few months after launch in November 1997. TRMM is currently on version 6 of the data product. Version 3 was the "at launch" version. The approval for each of these versions came through the Joint TRMM Science Team. Standard products are divided into 3 categories: single TRMM instrument, Visible Infrared Scanner (VIRS), TRMM Microwave Imager (TMI), and Precipitation Radar (PR); combined TRMM products (PR and TMI); finally TRMM and other satellites (combined, TMI, SSMI, AMSRE, AMSU). The single TRMM instrument products are processed through 4 levels: Level lA, science data packets processed into orbital files; Level 1B and lC, geolocated data at the instrument field of view; Level 2, geolocated, geophysical parameters at the instrument field of view; Level 3, time aggregated, gridded geophysical parameters. These products are available with 24 hours of production through an anonymous ftp account on trmmopen.gsfc.nasa.gov. The TRMM data system started to produce near real-time products at the end of 1999. They are currently available only through a controlled user account. However, approval to get access to this account can be obtained by sending a note to Erich.F.Stoclter@nasa.gov providing the reason for access and contact information including a valid email. TRMM is not restricting access but needs the information to determine the usefulness of near-real time data to the general science community including applications agencies. TRMM near real-time products are swath products up to Level 2 of processing. The oldest data in the swath is generally no older than 120 minutes when it becomes available to the community. The real-time products including a VIRS level lB, a TMI parameter reduced 1B, a TMI level 2 parameter reduced rain product, a PR level 2 surface rain product, and a PR level 2 rain product with 25 vertical levels. Currently, TRMM also produces a gridded 3 hour global merged product from several radiometers including AMSU and from radiometercalibrated IR data. The paper also describes several simple-format gridded text products available fiom the trmmopen.gsfc.nasa.gov anonymous fip server denoted as 3668 products. These products were produced to provide rain estimates from the three TRMM instruments in a universal format (ASCII) that requires very little data format knowledge. The paper goes on to describe prototype L1 radiometer products that apply an early intercalibration approach that provides a starting point to be used for Global Precipitation Measurement mission radiometer products. The paper also provides a brief overview of a precipitation features data product being produced using TRMM products including the Lighting Imaging Sensor (LIS) using an algorithm developed at the University of Utah and distributed by that organization. The paper concludes with some possible changes to products that are planned for the next reprocessing cycle and special services such as geographical subsetting available to the science community.
The Mars Sample Return Earth Entry System is the first entry vehicle designed for a NASA flagship mission to utilize a woven thermal protection system as well as a 52.5 degree sphere cone forebody geometry. As a result, no heritage aeroheating experimental data set exists to compare with computational predictions. In order to obtain a set of validation data for computational models, an extensive wind tunnel test campaign was funded by the Mars Sample Return Earth Entry System project. The first entry in the test campaign was completed in April of 2023, which was an investigation of turbulent heating augmentation due to woven thermal protection system roughness on the 52.5 degree Mars Sample Return - Earth Entry System vehicle forebody geometry. This test entry produced the first ever experimental aeroheating data on a 52.5 degree sphere-cone geometry as well as the first NASA experimental aeroheating data on a woven surface roughness pattern. Data obtained from this test campaign is being directly leveraged to support the NASA flight program, as experimental results are being utilized to validate the computational models which characterize the aeroheating environment that the vehicle experiences and predict turbulent surface heating levels and margins across the woven surface.
The Mars Sample Return Earth Entry System is the first entry vehicle designed for a NASA flagship mission to utilize a woven thermal protection system as well as a 52.5 degree sphere cone forebody geometry. As a result, no heritage aeroheating experimental data set exists to compare with computational predictions. In order to obtain a set of validation data for computational models, an extensive wind tunnel test campaign was funded by the Mars Sample Return Earth Entry System project. The first entry in the test campaign was completed in April of 2023, which was an investigation of turbulent heating augmentation due to woven thermal protection system roughness on the 52.5 degree Mars Sample Return - Earth Entry System vehicle forebody geometry. This test entry produced the first ever experimental aeroheating data on a 52.5 deg sphere-cone geometry as well as the first NASA experimental aeroheating data on a woven surface roughness pattern. Data obtained from this test campaign is being directly leveraged to support the NASA flight program, as experimental results are being utilized to validate the computational models which characterize the aeroheating environment that the vehicle experiences and predict turbulent surface heating levels and margins across the woven surface.