Search NASA⌕ Search

SEARCH · Search NASA

Results for “transport”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

The distribution of odd nitrogen in the lower stratosphere and possible perturbations caused by stratospheric air transport

In the lower stratosphere a significant production of odd nitrogen results from the reaction N2O + O(D-1) yields 2NO. Since the transport is relatively slow, odd nitrogen builds up with a maximum mixing ratio of 2 x 10 to the minus 8th power at 30 Km. Profiles of odd nitrogen, for different latitudes, winter and summer, are computed from one-dimensional transport models. Variations with latitude are small. Horizontal transport is therefore not believed to alter our results significantly. In order to evaluate the effect of odd nitrogen upon the ozone layer, NO(x) profiles are calculated. OH is here a key component, since it converts NO2 to HNO3. In the region where ozone is determined by chemistry rather than by transport (above 25 km), NO2 is found to be relatively abundant. The effect of stratospheric transport on the NO(x) distribution is shown to depend critically upon the height of emission. The effect increases by a factor of 5 or more for a change of flight level from 18 km to 23 km. This strong dependence should be duely considered when future stratospheric transport is discussed.

Isaksen, I. S. A.↗
NASA NTRS1974

Solid metabolic waste transport and stowage investigation

The basic Waste Collection System (WCS) design under consideration utilized air flow to separate the stool from the WCS user and to transport the fecal material to a slinger device for subsequent deposition on a storage bowel. The major parameters governing stool separation and transport were found to be the area of the air inlet orifices, the configuration of the air inlet orifice and the transport air flow. Separation force and transport velocity of the stool were studied. The developed inlet orifice configuration was found to be an effective design for providing fecal separation and transport. Simulated urine tests and female user tests in zero gravity established air flow rates between 0.08 and 0.25 cu sm/min (3 and 9 scfm) as satisfactory for entrapment, containment and transport of urine using an urinal. The investigation of air drying of fecal material as a substitute for vacuum drying in a WCS breadboard system showed that using baseline conditions anticipated for the shuttle cabin ambient atmosphere, flow rates of 0.14 cu sm/min (5 cfm) were adequate for drying and maintaining biological stability of the fecal material.

Burt, R. A.↗
NASA NTRS1977

Analogies between respiration and a light-driven proton pump as sources of energy for active glutamate transport in Halobacterium halobium

Halobacterium halobium is known to contain sheets of bacteriorhodopsin, a pigment which upon exposure to light undergoes cyclic protonation and deprotonation, resulting in net H(+) translocation. In this paper, experiments were conducted to test H. halobium cell envelope vesicles for respiration-induced glutamate uptake. It is shown that glutamate transport in H. halobium cell envelope vesicles can occur as a result of respiration, as well as light acting on bacteriorhodopsin. Glutamate transport can be energized by the oxidation of dimethyl phenylenediamine, and the properties of the transport system are entirely analogous to those observed with illumination as the source of energy. In the case of respiration-dependent glutamate transport, the transportation is also driven by a Na(+) gradient, thereby confirming the existence of a single glutamate transport system independent of the source of energy. The analogy observed is indirect evidence that the cytochrome oxidase of H. halobium functions as a H(+) pump.

Belliveau, J. W.↗
NASA NTRS1976

Payload transportation system study

A standard size set of shuttle payload transportation equipment was defined that will substantially reduce the cost of payload transportation and accommodate a wide range of payloads with minimum impact on payload design. The system was designed to accommodate payload shipments between the level 4 payload integration sites and the launch site during the calendar years 1979-1982. In addition to defining transportation multi-use mission support equipment (T-MMSE) the mode of travel, prime movers, and ancillary equipment required in the transportation process were also considered. Consistent with the STS goals of low cost and the use of standardized interfaces, the transportation system was designed to commercial grade standards and uses the payload flight mounting interfaces for transportation. The technical, cost, and programmatic data required to permit selection of a baseline system of MMSE for intersite movement of shuttle payloads were developed.

Source record↗
NASA NTRS1979

Low-speed wind-tunnel investigation of wing fins as trailing-vortex-alleviation devices on a transport airplane model

The trailing-vortex-alleviation effectiveness of both a one- and a two-fin configuration (semicircular with a radius of 0.043 semispan) on a jumbo-jet transport airplane model in its landing configuration was investigated in the Langley V/STOL tunnel, by the trailing-wing sensor technique. The fins were located on the upper surface of the transport model wing along the 30-percent-chord line. The fin configurations were effective in reducing the vortex-induced rolling moment, by amounts varying from 28 to 60 percent, on the trailing wing model located at a distance of 7.8 transport model wing spans downstream of the transport model. The flow over the fins and over the transport airplane model wing downstream of the fins was observed to be separated and turbulent. All fin configurations caused a reduction in maximum lift coefficient, a positive increment in drag coefficient, and an increment in nose-up pitching-moment coefficient on the transport airplane model.

Croom, D. R.↗
NASA NTRS1978

Apparent cooperativity of amino acid transport in Halobacterium halobium - Effect of electrical potential

Active serine accumulation in cell envelope vesicles from Halobacterium halobium proceeds by co-transport with Na(+) and can be induced by either transmembrane electrical potential or transmembrane Na(+) concentration difference. It was shown earlier that in the former case the initial transport rate is a fourth-power function of the magnitude of the electrochemical potential difference of sodium ions, and in the latter, a second-power function. A possible interpretation of this finding is cooperativity of sodium-transporting sites in the transport carrier. When both kinds of driving force are imposed simultaneously on the vesicles, fourth-power dependence on the total potential difference of sodium ions is obtained, suggesting that the transport carrier is regulated by the electrical potential. Heat treatment of the vesicles at 48 C partially inactivates transport and abolishes this effect of the electrical potential.

Lanyi, J. K.↗
NASA NTRS1979

The role of Na/+/ in transport processes of bacterial membranes

Until recently it was generally held that transport in bacteria was linked exclusively to proton circulation, in contrast to most eucaryotic systems, which depended on Na(+) circulation. The present review is intended to trace recent developments which have led to the discarding of this idea. The discussion covers transport of Na(+) and other cations, effects of Na(+) and Na(+) gradients on metabolite transport, properties of Na(+)-dependent transport carriers, and evolutionary considerations of Na(+) transport. It is now apparent that the transport of Na(+) is an important part of energy metabolism in bacteria, and that Na(+) gradients as well as H(+) gradients are used in these systems for the conservation and transmission of energy. Two hypotheses are proposed to explain the evolution of Na/K systems, and it is presently difficult to decide between them.

Lanyi, J. K.↗
NASA NTRS1981

Numerical modeling of diffusive-convective physical vapor transport in cylindrical vertical ampoules

Diffusive-convective physical vapor transport (PVT) in cylindrical, vertical ampoules of aspect ratio (length/radius) between 0.5 and 10 was modeled numerically. The transport of a crystal forming component through an inert component that undergoes zero net transport was considered. Systems were treated in which: (1) with unequal molecular weight of the components and with temperature gradients typically employed in PVT, convective flow arises dominantly from solutal density gradients; and (2) with equal molecular weight of the components, convective flow can arise only from thermal expansion. It was found that, due to the diffusion-induced horizontal density gradients, buoyancy-driven convective flows are superimposed on the diffusive-advective fluxes without threshold. Net recirculation sets in adjacent to the growing interface, in contrast to the corresponding monocomponent situation where marginally stable convective modes fill the whole fluid space. Depending on the orientation of the main transport direction with respect to gravity, convection can either reduce or enhance the diffusion-induced radial concentration gradients. Significant enhancement of the net transport rate was found to occur only when the whole vapor space between source and growing crystal is filled by a convective recirculation roll. Solutal and thermal convection results are similar; yet for quantitative discussions, thermal and solutal Rayleigh numbers are not interchangeable in contrast to convective situations that lack net mass transport across the fluid space.

Markham, B. L.↗
NASA NTRS1981

Mass and Momentum Turbulent Transport Experiments with Confined Coaxial Jets

Downstream mixing of coaxial jets discharging in an expanded duct was studied to obtain data for the evaluation and improvement of turbulent transport models currently used in a variety of computational procedures throughout the propulsion community for combustor flow modeling. Flow visualization studies showed four major shear regions occurring; a wake region immediately downstream of the inlet jet inlet duct; a shear region further downstream between the inner and annular jets; a recirculation zone; and a reattachment zone. A combination of turbulent momentum transport rate and two velocity component data were obtained from simultaneous measurements with a two color laser velocimeter (LV) system. Axial, radial and azimuthal velocities and turbulent momentum transport rate measurements in the r-z and r-theta planes were used to determine the mean value, second central moment (or rms fluctuation from mean), skewness and kurtosis for each data set probability density function (p.d.f.). A combination of turbulent mass transport rate, concentration and velocity data were obtained system. Velocity and mass transport in all three directions as well as concentration distributions were used to obtain the mean, second central moments, skewness and kurtosis for each p.d.f. These LV/LIF measurements also exposed the existence of a large region of countergradient turbulent axial mass transport in the region where the annular jet fluid was accelerating the inner jet fluid.

Johnson, B. V.↗
NASA NTRS1983

Mass and momentum turbulent transport experiments with confined swirling coaxial jets

Swirling coaxial jets mixing downstream, discharging into an expanded duct was conducted to obtain data for the evaluation and improvement of turbulent transport models currently used in a variety of computational procedures throughout the combustion community. A combination of laser velocimeter (LV) and laser induced fluorescence (LIF) techniques was employed to obtain mean and fluctuating velocity and concentration distributions which were used to derive mass and momentum turbulent transport parameters currently incorporated into various combustor flow models. Flow visualization techniques were also employed to determine qualitatively the time dependent characteristics of the flow and the scale of turbulence. The results of these measurements indicated that the largest momentum turbulent transport was in the r-z plane. Peak momentum turbulent transport rates were approximately the same as those for the nonswirling flow condition. The mass turbulent transport process for swirling flow was complicated. Mixing occurred in several steps of axial and radial mass transport and was coupled with a large radial mean convective flux. Mixing for swirling flow was completed in one-third the length required for nonswirling flow.

Roback, R.↗
NASA NTRS1984

Ballistic transport in Saturn's rings - An analytic theory

Ejecta from impacts of micrometeoroids on Saturn's ring particles will, in most cases, remain in orbit about Saturn and eventually be reaccreted by the rings, possibly at a different radial location. The resulting mass transport has been suggested as the cause of some of the features observed in Saturn's rings. Previous attempts to model this transport have used numerical simulations which have not included the effects of the angular momentum transport coincident with mass transport. An analytical model for ballistic mass transport in Saturn's rings is developed. The model includes the effects of angular momentum advection and shows that the net material movement due to angular momentum advection is comparable to that caused by direct ballistic mass transport.

Lissauer, J. J.↗
NASA NTRS1985

Ground-based and in-flight simulator studies of flight characteristics of a twin-fuselage passenger transport airplane during approach and landing

Six-degree-of-freedom ground-based and in-flight simulator studies were conducted to evaluate the low-speed flight characteristics of a twin-fuselage passenger transport airplane and to compare these characteristics with those of a large, single-fuselage (reference) transport configuration similar to the Lockheed C-5A airplane. The primary piloting task was the approach and landing task. The results of this study indicated that the twin-fuselage transport concept had acceptable but unsatisfactory longitudinal and lateral-directional low-speed flight characteristics, and that stability and control augmentation would be required in order to improve the handling qualities. Through the use of rate-command/attitude-hold augmentation in the pitch and roll axes, and the use of several turn coordination features, the handling qualities of the simulated transport were improved appreciably. The in-flight test results showed excellent agreement with those of the six-degree-of-freedom ground-based simulator handling qualities tests. As a result of the in-flight simulation study, a roll-control-induced normal-acceleration criterion was developed. The handling qualities of the augmented twin-fuselage passenger transport airplane exhibited an improvement over the handling characteristics of the reference (single-fuselage) transport.

Grantham, W. D.↗
NASA NTRS1985

Microinstabilities and anomalous transport

The role of microinstabilities in producing dissipation and anomalous transport in collisionless shock waves is reviewed. Particular emphasis is placed on quasiturbulent magnetosonic shocks. The review follows the historical development of anomalous transport and the incorporation of the coefficients into multifluid and hybrid models. A general formalism is presented which describes in a self-consistent manner, the macroscopic transport produced by short wavelength microinstabilities. Similarities and differences with models incorporating classical transport are emphasized. The important instabilities and their transport properties are summarized. It is shown that multifluid simulations with anomalous transport explain many features of the experimental observations. The relevance of ion reflection and the necessity for kinetic ion description for supercritical shocks along with state of the art numerical studies are also discussed. The review concludes with a brief discussion of the piston shock problem and of quasi-parallel turbulent shocks.

Papadopoulos, K.↗
NASA NTRS1989

A Mars/phobos Transportation System

A transportation system will be necessary to support construction and operation of bases on Phobos and Mars beginning in the year 2020 or later. An approach to defining a network of vehicles and the types of vehicles which may be used in the system are presented. The network will provide a convenient, integrated means for transporting robotically constructed bases to Phobos and Mars. All the technology needed for the current plan is expected to be available for use at the projected date of cargo departure from the Earth system. The modular design of the transportation system provides easily implemented contingency plans, so that difficulties with any one vehicle will have a minimal effect on the progress of the total mission. The transportation network proposed consists of orbital vehicles and atmospheric entry vehicles. Initially, only orbital vehicles will participate in the robotic construction phase of the Phobos base. The Interplanetary Transfer Vehicle (ITV) will carry the base and construction equipment to Phobos where the Orbital Maneuvering Vehicles (OMV's) will participate in the initial construction of the base. When the Mars base is ready to be sent, one or more ITV's will be used to transport the atmospheric entry vehicles from Earth. These atmospheric vehicles are the One Way Landers (OWL's) and the Ascent/Descent Vehicles (ADV's). They will be used to carry the base components and/or construction equipment. The OMV's and the Orbital Transfer Vehicles (OTV's) will assist in carrying the atmospheric entry vehicles to low Martian orbit where the OWL's or ADV's will descent to the planet surface. The ADV's were proposed to accommodate expansion of the system. Additionally, a smaller version of the ADV class is capable of transporting personnel between Mars and Phobos.

Source record↗
NASA NTRS1990

A mobile transporter concept for EVA assembly of future spacecraft

This paper details the ground test program for the NASA Langley Research Center Mobile Transporter concept. The Mobile Transporter would assist EVA astronauts in the assembly of the Space Station Freedom. 1-g and simulated O-g (neutral buoyancy) tests were conducted to evaluate the use of the Mobile Transporter. A three-bay (44 struts) orthogonal tetrahedral truss configuration with a 15-foot-square cross section was repeatedly assembled by a single pair of pressure suited test subjects working from the Mobile Transporter astronaut positioning devices. The average unit assembly time was 28 seconds/strut. The results of these tests indicate that the use of a Mobile Transporter for EVA assembly of Space Station size structure is viable and practical. Additionally, the Mobile Transporter could be used to construct other spacecraft such as the submillimeter astronomical laboratory, space crane, and interplanetary (i.e., Mars and lunar) spacecraft.

Watson, Judith J.↗
NASA NTRS1991

Next generation: In-space transportation system(s)

The development of the next generation In-Space Transportation System presents a unique challenge to the design of a propulsion system for the Space Exploration Initiative (SEI). Never before have the requirements for long-life, multiple mission use, space basing, high reliability, man-rating, and minimum maintenance come together with performance in one system that must protect the lives of space travelers, support the mission logistics needs, and do so at an acceptable cost. The challenge that is presented is to quantify the bounds of these requirements. The issue is one of degree. The length of acceptable life in space, the time it takes for reuse to pay off, and the degree to which space basing is practical (full, partial, or expended) are the issues that determine the reusable bounds of a design and include dependability, contingency capabilities, resilency, and minimum dependence on a maintenance node in preparation for and during a mission. Missions to planet earth, other non-NASA missions, and planetary missions will provide important but less demanding requirements for the transportation systems of the future. The mission proposed for the SEI require a family of transportation vehicles to meet the requirements for establishing a permanent human presence on the Moon and eventually on Mars. Specialized vehicles are needed to accomplish the different phases of each mission. These large scale missions require assembly in space and will provide the greatest usage of the planned integrated transportation system. The current approach to defining the In-Space Transportation System for the SEI Moon missions with later Mars mission applications is presented. Several system development options, propulsion concepts, current/proposed activities are reviewed, and key propulsion design criteria, issues, and technology challenges for the next generation In-Space Transportation System(s) are outlined.

Huffaker, Fredrick↗
NASA NTRS1992

Advanced propulsion for LEO-Moon transport. 2: Tether configurations in the LEO-Moon system

This brief work discusses a possible application of a tether as a dynamical element in a low Earth orbit (LEO)-Moon transport system, and is a part of the Cal Space study of that transport system. To be specific, that study concentrated on the downward transport of O2 from the Moon to LEO, where it is stored for use as a rocket propellant, thus reducing Earth liftoff mass requirements by a factor of about 8. Moreover, in order to display clearly the role of advanced technology, only one novel technology was introduced at a single node in the transport system, the rest being 'conventional' rocket transport. Tethers were found useful in several different roles: hanging from platforms in lunar orbits, as supports for elevators, spinning in LEO, or spinning in a tether transport orbit, an elliptical orbit with perigee at approximately 600 km. This last use is considered here. Presented are the usefulness of the tether, nature of the tether system, the apparatus needed to support, deploy, and control it, and a discussion of needed developments.

Arnold, J. R.↗
NASA NTRS1992

Activated transport in AMTEC electrodes

Transport of alkali, metal atoms through porous cathodes of alkali metal thermal-to-electric converter (AMTEC) cells is responsible for significant reducible losses in the electrical performance of these cells. Experimental evidence for activated transport of metal atoms at grain surfaces and boundaries within some AMTEC electrodes has been derived from temperature dependent studies as well as from analysis of the detailed frequency dependence of ac impedance results for other electrodes, including thin, mature molybdenum electrodes which exhibit transport dominated by free molecular flow of sodium gas at low frequencies or dc conditions. Activated surface transport will almost always exist in parallel with free molecular flow transport, and the process of alkali atom adsorption/desorption from the electrode surface will invariably be part of the transport process, and possibly a dominant part in some cases. The temperature dependence of the diffusion coefficient of the alkali metal through the electrode in several cases provides an activation energy and preexponential, but at least two activated processes may be operative, and the activation parameters should be expected to depend on the alkali metal activity gradient that the electrode experiences. In the case of Pt/W/Mn electrodes operated for 2500 hours, limiting currents varied with electrode thickness, and the activation parameters could be assigned primarily to the surface/grain boundary diffusion process.

Williams, R. M.↗