Search NASA⌕ Search

SEARCH · Search NASA

Results for “wheeled”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

Study of Systems Using Inertia Wheels for Precise Attitude Control of a Satellite

Systems using inertia wheels are evaluated in this report to determine their suitability for precise attitude control of a satellite and to select superior system configurations. Various possible inertia wheel system configurations are first discussed in a general manner. Three of these systems which appear more promising than the others are analyzed in detail, using the Orbiting Astronomical Observatory as an example. The three systems differ from each other only by the method of damping, which is provided by either a rate gyro, an error-rate network, or a tachometer in series with a high-pass filter. An analytical investigation which consists of a generalized linear analysis, a nonlinear analysis using the switching-time method, and an analog computer study shows that all three systems are theoretically capable of producing adequate response and also of maintaining the required pointing accuracy for the Orbiting Astronomical Observatory of plus or minus 0.1 second of arc. Practical considerations and an experimental investigation show, however, that the system which uses an error-rate network to provide damping is superior to the other two systems. The system which uses a rate gyro is shown to be inferior because the threshold level causes a significant amount of limit-cycle operation, and the system which uses a tachometer with a filter is shown to be inferior because a device with the required dynamic range of operation does not appear to be available. The experimental laboratory apparatus used to investigate the dynamic performance of the systems is described, and experimental results are included to show that under laboratory conditions with relatively large extraneous disturbances, a dynamic tracking error of less than plus or minus 0.5 second of arc was obtained.

White, John S.↗
NASA NTRS1948

Effect of Turbine Axial Nozzle-Wheel Clearance on Performance of Mark 25 Torpedo Power Plant

Investigations were made of the turbine from a Mark 25 torpedo to determine the performance of the unit with three different turbine nozzles at various axial nozzle-wheel clearances. Turbine efficiency with a reamed nondivergent nozzle that uses the axial clearance space for gas expansion was little affected by increasing the axial running clearance from 0.030 to 0.150 inch. Turbine efficiency with cast nozzles that expanded the gas inside the nozzle passage was found to be sensitive to increased axial nozzle-wheel clearance. A cast nozzle giving a turbine brake efficiency of 0.525 at an axial running clearance of 0.035 inch gave a brake efficiency of 0.475 when the clearance was increased to 0.095 inch for the same inlet-gas conditions and blade-jet speed ratio. If the basis for computing the isentropic power available to the turbine is the temperature inside the nozzle rather then the temperature in the inlet-gas pipe, an increase in turbine efficiency of about 0.01 is indicated.

Hoyt, Jack W.↗
NASA NTRS2007

Zero Gyro Kalman Filtering in the Presence of a Reaction Wheel Failure

Typical implementation of Kalman filters for spacecraft attitude estimation involves the use of gyros for three-axis rate measurements. When there are less than three axes of information available, the accuracy of the Kalman filter depends highly on the accuracy of the dynamics model. This is particularly significant during the transient period when a reaction wheel with a high momentum fails, is taken off-line, and spins down. This paper looks at how a reaction wheel failure can affect the zero-gyro Kalman filter performance for the Hubble Space Telescope and what steps are taken to minimize its impact.

Hur-Diaz, Sun↗
NASA NTRS2007

Zero Gyro Kalman Filtering in the presence of a Reaction Wheel Failure

Typical implementation of Kalman filters for spacecraft attitude estimation involves the use of gyros for three-axis rate measurements. When there are less than three axes of information available, the accuracy of the Kalman filter depends highly on the accuracy of the dynamics model. This is particularly significant during the transient period when a reaction wheel with a high momentum fails, is taken off-line, and spins down. This paper looks at how a reaction wheel failure can affect the zero-gyro Kalman filter performance for the Hubble Space Telescope and what steps are taken to minimize its impact.

Hur-Diaz, Sun↗
NASA NTRS2007

Design and Optimization of Composite Gyroscope Momentum Wheel Rings

Stress analysis and preliminary design/optimization procedures are presented for gyroscope momentum wheel rings composed of metallic, metal matrix composite, and polymer matrix composite materials. The design of these components involves simultaneously minimizing both true part volume and mass, while maximizing angular momentum. The stress analysis results are combined with an anisotropic failure criterion to formulate a new sizing procedure that provides considerable insight into the design of gyroscope momentum wheel ring components. Results compare the performance of two optimized metallic designs, an optimized SiC/Ti composite design, and an optimized graphite/epoxy composite design. The graphite/epoxy design appears to be far superior to the competitors considered unless a much greater premium is placed on volume efficiency compared to mass efficiency.

Bednarcyk, Brett A.↗
NASA NTRS2011

Wheel-Based Ice Sensors for Road Vehicles

Wheel-based sensors for detection of ice on roads and approximate measurement of the thickness of the ice are under development. These sensors could be used to alert drivers to hazardous local icing conditions in real time. In addition, local ice-thickness measurements by these sensors could serve as guidance for the minimum amount of sand and salt required to be dispensed locally onto road surfaces to ensure safety, thereby helping road crews to utilize their total supplies of sand and salt more efficiently. Like some aircraft wing-surface ice sensors described in a number of previous NASA Tech Briefs articles, the wheelbased ice sensors are based, variously, on measurements of changes in capacitance and/or in radio-frequency impedance as affected by ice on surfaces. In the case of ice on road surfaces, the measurable changes in capacitance and/or impedance are attributable to differences among the electric permittivities of air, ice, water, concrete, and soil. In addition, a related phenomenon that can be useful for distinguishing between ice and water is a specific transition in the permittivity of ice at a temperature- dependent frequency. This feature also provides a continuous calibration of the sensor to allow for changing road conditions. Several configurations of wheel-based ice sensors are under consideration. For example, in a simple two-electrode capacitor configuration, one of the electrodes would be a circumferential electrode within a tire, and the ground would be used as the second electrode. Optionally, the steel belts that are already standard parts of many tires could be used as the circumferential electrodes. In another example (see figure), multiple electrodes would be embedded in rubber between the steel belt and the outer tire surface. These electrodes would be excited in alternating polarities at one or more suitable audio or radio frequencies to provide nearly continuous monitoring of the road surface under the tire. In still another example, one or more microwave stripline(s) or coplanar waveguide(s) would be embedded in a tire near its outer surface; in comparison with lower-frequency capacitive devices, a device of this type could be more sensitive.

Arndt, G. Dickey↗
NASA NTRS2013

Characterizing the Perfonnance of the Wheel Electrostatic Spectrometer

A Wheel Electrostatic Spectrometer has been developed as a surveying tool to be incorporated into a planetary rover design. Electrostatic sensors with various protruding cover insulators are embedded into a prototype rover wheel. When these insulators come into contact with a surface, a charge develops on the cover insulator through tribocharging. A charge spectrum is created by analyzing the accumulated charge on each of the dissimilar cover insulators. We eventually intend to prove charge spectra can be used ~o determine differences in planetary regolith properties. We tested the effects of residual surface charge on the cover insulators and discovered a need to discharge the sensor cover insulators after each revolution. We proved the repeatability of the measurements for this sensor package and found that the sensor repeatability lies within one standard deviation of the noise in the signal.

Johansen, Michael R.↗
NASA NTRS2014

A Feasability Study of the Wheel Electrostatic Spectrometer

Mars rover missions rely on time-consuming, power-exhausting processes to analyze the Martian regolith. A low power electrostatic sensor in the wheels of a future Mars rover could be used to quickly determine when the rover is driving over a different type of regolith. The Electrostatics and Surface Physics Laboratory at NASA's Kennedy Space Center developed the Wheel Electrostatic Spectrometer as a feasibility study to investigate this option. In this paper, we discuss recent advances in this technology to increase the repeatability of the tribocharging experiments, along with supporting data. In addition, we discuss the development of a static elimination tool optimized for Martian conditions.

Tribocharging↗
NASA NTRS2014

Metering Wheel-Wire Track Wire Boom Deployment Mechanism

The NASA MMS Spin Plane Double Probe (SDP) Deployer utilizes a helical path, rotating Metering Wheel and a spring loaded Wire "Holding" Track to pay out a "fixed end" 57 meter x 1.5 mm diameter Wire Boom stored between concentric storage cylinders. Unlike rotating spool type storage devices, the storage cylinders remain stationary, and the boom wire is uncoiled along the length of the cylinder via the rotation of the Metering Wheel. This uncoiling action avoids the need for slip-ring contacts since the ends of the wire can remain stationary. Conventional fixed electrical connectors (Micro-D type) are used to terminate to operational electronics.

Granoff, Mark S.↗
NASA NTRS2018

Understanding the Kepler Reaction Wheels & Satellite

Following the loss of two reaction wheels four years into its mission, the Kepler team was faced with reinventing an operational approach to continue to deliver compelling science using an unanticipated suite of actuators. Spacecraft thrusters were not designed for accurate pointing control, yet with only two reaction wheels, only two axes could be actively controlled. With solar pressure as the only disturbing force, and recognizing the innate symmetry of the spacecraft, the K2 mission points the spacecraft in the orbital plane for three months at a time, placing the antennas 90° from the earth. Mapping the solar balance ridge 70 M km from Earth, with limited communications and a reduced staff presented a significant operational challenge.

Engineering↗
NASA NTRS2017

A Hybrid Traveling Salesman Problem - Squeaky Wheel Optimization Planner for Earth Observational Scheduling

We outline a hybrid planner for scheduling Observa- tion Requests on an Earth observing satellite, subject to a variety of constraints for the ASPEN (Chien et al. 2000) Eagle Eye adaptation (Knight, Donnellan, and Green 2013) that combines Squeaky Wheel Optimiza- tion (Joslin and Clements 1999) with sliding observa- tion planning (Aldinger et al. 2013). The Earth Ob- serving Satellite (EOS) planning problem (Globus et al. 2004) is reformulated as time-varying travel time TSP with interval constraints (Ichoua, Gendreau, and Potvin 2003). The replanning/ ll stage of the hybrid scheduler marginally improves schedule quality for all bus agilities examined, but has more impact on lower agility observers. The squeaky wheel stage primarily a ects overall schedule quality by satisfying high pri- ority requests, while the replanner reduces starvation of lower value requests.

Trowbridge, Michael↗
NASA NTRS2019

WFIRST Low Order WaveFront Sensing and Control (LOWFS/C) performance on line-of-sight disturbances from multiple reaction wheels

In this paper we will describe the LOWFS/C LoS performance test in which the injected LoS disturbances are derived from all six reaction wheels on WFIRST, each with an independent varying wheel speed profile modeled for a typical coronagraph observational scenario. We will describe the LoS disturbances profile and testbed implementation approach. We will present the LOWFS/C LoS feedback and feed forward loops testbed performance under these realistic LoS disturbances in which we have demonstrated the LoS control that meets the CGI requirement.

Shelton, Chris↗
NASA NTRS2020

Barefoot Rover: a Sensor-Infused Rover Wheel Demonstrating In-Situ Engineering and Science Extractions using Machine Learning

In this work, we demonstrate an instrumented wheel concept which utilizes a 2D pressure grid, an electrochemical impedance spectroscopy (EIS) sensor and machine learning (ML) to extract meaningful metrics from the interaction between the wheel and surface terrain. These include continuous slip/skid estimation, balance, and sharpness for engineering applications. Estimates of surface hydration, texture, terrain patterns, and regolith physical properties such as cohesion and angle of internal friction are additionally calculated for science applications. Traditional systems rely on post-processing of visual images and vehicle telemetry to estimate these metrics. Through in-situ sensing, these metrics can be calculated in near real time and made available to onboard science and engineering autonomy applications. This work aims to provide a deployable system for future planetary exploration missions to increase science and engineering capabilities through increased knowledge of the terrain.

Marchetti, Yuliya↗
NASA NTRS2020

Mobility Mode Evaluation of a Wheel-on-Limb Rover on Glacial Ice Analogous to Europa Terrain

In this paper, we discuss the development of a multi-modal locomotion system and the results of field trials performed on fractured, glacial ice. Work was performed using the RoboSimian rover: a 32 degree-of-freedom, actively articulated mobility system. Three modes of mobility are compared: wheelrolling, inchworming (push-rolling) and wheel-walking. Each mobility mode is designed to operate with articulated suspension whereby the normal load per wheel, body orientation, and available limb workspace are actively controlled. Each mode is presented individually alongside a discussion of its performance on terrain of varied slope and topographic roughness. Further, the utility of a multi-modal approach is presented, whereby rover immobilization was avoided during field trials through the selection of appropriate mobility modes as a function of terrain properties. Lastly, the results of trials performed using a bodymounted sampling system and its ability to collect and process samples taken 10 cm beneath the surface are discussed.

Reid, William↗