Search NASA⌕ Search

SEARCH · Search NASA

Results for “wind tunnel characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 181 records · Page 10
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Degradation Characterization of Unsteady Pressure-Sensitive Paint Under Various Pressures

The lifetime and intensity techniques are two distinct methods used to measure the surface pressure of wind tunnel models with pressure-sensitive paint (PSP). When exposed to 405 nm light for extended periods, both the luminescence and the lifetime ratio were observed to decrease, affecting perceived pressure values. To help further the implementation of the uPSP, this paper describes the efforts to characterize the degradation of both the intensity of the paint and its lifetime ratio, as well as the change in intensity calibration. It was found that the paint degrades at different rates depending on the partial pressure of oxygen during excitation. It was also found that the calibration curves exhibit greater changes when under higher oxygen concentrations, both indicating photodegradation due to photodecomposition and photo-oxidation processes. These effects are observed on models in a subsonic 14” × 14” wind tunnel. The work provides insight into the dynamic degradation behavior of PSP and uPSP, paving the way to reduce the error in pressure measurements obtained through these techniques.

Pressure-Sensitive Paint↗
NASA NTRSDate not supplied

Upwind Buildings Effects on Test Section Performance of the NFAC 80- by 120-Foot Wind Tunnel

In 2013, a new development began that would put multi-story buildings within the exclusion zone of the 80- by 120- Foot Wind Tunnel (80x120) inlet that exceeded the then existing building height restriction. This raised questions concerning whether the tunnel could operate within the acceptable turbulence limits of ≤ 0.5% in the axial direction over 75% area in the wind tunnel test section. The goal of this testing was to determine the validity of this hypothesis. Testing was performed using the 1/50th-scale model of the 80- by 120-FootWind Tunnel within the full-scale facility test section to characterize the model’s test section turbulence levels as a function of wind direction with the presence of the upwind buildings that are currently being constructed. This paper reports the first testing performed to date on the 80x120 inlet as-built under controlled test conditions for wind magnitude and wind onset direction for a variety of buildings in the inlet external flow field, including no buildings (the control case). This testing determined that, at rated operational conditions the upwind blockages caused no increase in turbulence intensity levels measured in the test section and, in some limited cases, caused the turbulence levels to decrease. Lastly, looking at generic rectangular blockages showed that, to have a discernible effect on test section turbulence levels, scaled 100-ft tall blockages need to be within 600 ft of the existing inlet.

Upwind Buildings Effects↗
NASA NTRSDate not supplied

Flow Characterization of the NASA Langley Unitary Plan WindTunnel, Test Section 2: Computational Results

Flow in the empty Unitary Planform Wind Tunnel at the NASA Langley Research Center issimulated with computational fluid dynamics methods. The objectives are to assess CFD’s truepredictive capability and to generate flow-field maps upstream of the tunnel’s test section foruse in associated vehicle tests. Multiple CFD solvers, grid adaption methods, and turbulencemodels are used by five teams doing the simulations. The simulation domain is as large aspractical: from the start of the settling chamber, just downstream of the last set of turningvanes, to well downstream of the test section. Simulations are done at three Mach numbers andseveral Reynolds numbers that cover most of the tunnel’s operating range. The sensitivity ofthe CFD solutions to simulation process details, including turbulence model, spatial resolutionand settling-chamber inflow velocity profile, is characterized. Significant sensitivities in somedetails of the predicted test section flow are described. CFD predicts that details of flow inthe settling chamber can affect the flow in the test section. Turning of the flow through thetunnel contraction and past nozzle-block hardware generates streamwise vortices, some ofwhich survive into the core of the test section, principally at low Mach number. Preliminarycomparisons to experimental measurements are given. The major flow characteristics andthe dynamical vortices predicted by CFD exist in the experiment. Several details in CFD andexperiment are observed to differ, including the effects of the vortices and features that appearto be Mach waves in the test section. Sensitivity to grid resolution and turbulence modelingis noted in the vortices; no potential cause for the differences in Mach waves has yet beenidentified in the CFD sensitivity studies.

wind tunnel↗
NASA NTRS1937

Full-Scale Tests of a New Type NACA Nose-Slot Cowling

An extended experimental study has been made in regard to the various refinements in the design of engine cowlings as related to the propeller-nacelle unit as a whole, under conditions corresponding to take-off, climb, and normal flight. The tests were all conducted at full scale in the 20-foot wind tunnel. This report presents the results of a novel type of engine cowling, characterized by the fact that the exit opening discharging the cooling air is not, as usual, located behind the engine but at the foremost extremity or nose of the cowling. The efficiency is found to be high, owing to the fact that higher velocities may be used in the exit opening.

Theodorsen, Theodore↗
NASA NTRS2014

Characterization of a Laser-Generated Perturbation in High-Speed Flow for Receptivity Studies

A better understanding of receptivity can contribute to the development of an amplitude-based method of transition prediction. This type of prediction model would incorporate more physics than the semi-empirical methods, which are widely used. The experimental study of receptivity requires a characterization of the external disturbances and a study of their effect on the boundary layer instabilities. Characterization measurements for a laser-generated perturbation were made in two different wind tunnels. These measurements were made with hot-wire probes, optical techniques, and pressure transducer probes. Existing methods all have their limitations, so better measurements will require the development of new instrumentation. Nevertheless, the freestream laser-generated perturbation has been shown to be about 6 mm in diameter at a static density of about 0.045 kg/cubic m. The amplitude of the perturbation is large, which may be unsuitable for the study of linear growth.

Chou, Amanda↗
NASA NTRS1985

The space shuttle ascent vehicle aerodynamic challenges configuration design and data base development

The phase B Space Shuttle systems definition studies resulted in a generic configuration consisting of a delta wing orbiter, and two solid rocket boosters (SRB) attached to an external fuel tank (ET). The initial challenge facing the aerodynamic community was aerodynamically optimizing, within limits, this configuration. As the Shuttle program developed and the sensitivities of the vehicle to aerodynamics were better understood the requirements of the aerodynamic data base grew. Adequately characterizing the vehicle to support the various design studies exploded the size of the data base to proportions that created a data modeling/management challenge for the aerodynamicist. The ascent aerodynamic data base originated primarily from wind tunnel test results. The complexity of the configuration rendered conventional analytic methods of little use. Initial wind tunnel tests provided results which included undesirable effects from model support tructure, inadequate element proximity, and inadequate plume simulation. The challenge to improve the quality of test results by determining the extent of these undesirable effects and subsequently develop testing techniques to eliminate them was imposed on the aerodynamic community. The challenges to the ascent aerodynamics community documented are unique due to the aerodynamic complexity of the Shuttle launch. Never before was such a complex vehicle aerodynamically characterized. The challenges were met with innovative engineering analyses/methodology development and wind tunnel testing techniques.

Dill, C. C.↗
NASA NTRS1995

Experimental Technique and Assessment for Measuring the Convective Heat Transfer Coefficient from Natural Ice Accretions

A technique was developed to cast frozen ice shapes that had been grown on a metal surface. This technique was applied to a series of ice shapes that were grown in the NASA Lewis Icing Research Tunnel on flat plates. Nine flat plates, 18 inches square, were obtained from which aluminum castings were made that gave good ice shape characterizations. Test strips taken from these plates were outfitted with heat flux gages, such that when placed in a dry wind tunnel, can be used to experimentally map out the convective heat transfer coefficient in the direction of flow from the roughened surfaces. The effects on the heat transfer coefficient for both parallel and accelerating flow will be studied. The smooth plate model verification baseline data as well as one ice roughened test case are presented.

Masiulaniec, K. Cyril↗
NASA NTRSDate not supplied

Characterization of Photodegredation in Unsteady Pressure-Sensitive Paint Under Varying Pressures

The lifetime and intensity techniques are two distinct methods used to measure the surface pressure of wind tunnel models with pressure-sensitive paint (PSP). When exposed to 405 nm light for extended periods, both the luminescence and the lifetime ratio were observed to decrease, affecting perceived pressure values. To help further the implementation of the unsteady pressure-sensitive paint (uPSP), this paper describes the efforts to characterize how photo degradation affects the intensity of the paint signal and its lifetime ratio, as well as the intensity calibration's response and how these changes vary with different pressure environments. It was found that the paint photo degrades at different rates depending on the partial pressure of oxygen during excitation. It was also found that the calibration curves exhibit greater changes when exposed to excitation light in higher pressure environments, both indicating photo degradation due to photo decomposition and photo-oxidation processes. These effects are observed on models in a subsonic 14” × 14” wind tunnel as well as a large-scale 11’ x 11’ transonic wind tunnel. The work provides analysis into the photo degradation behavior of PSP and uPSP, paving the way to reduce the error in pressure measurements obtained through these techniques.

Pressure-Sensitive Paint↗
NASA NTRS2019

Aerodynamic Characterization and Improved Testing Methods for the Space Launch System Liftoff and Transition Environment

Low-speed wind tunnel testing for the liftoff and transition environment of the Space Launch System (SLS) was recently completed in the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel using 1.75%-scale models of three SLS vehicle configurations. During the liftoff testing, the primary objective was to evaluate the aerodynamic forces and moments on the SLS launch vehicles, as the vehicle, launch tower, and mobile launch platform were subjected to ground winds from all directions at varying heights for the vehicle off the launch pad. Additionally, aerodynamic forces and moments were acquired for all three SLS vehicles during the transition phase from liftoff to ascent that covered a wide range of angles of attack and angles of side slip. Details of the experimental setup including improved testing methods and a stiffer sting-balance system based on lessons learned from previous test entries are presented. Also, a new force measurement technique was applied during the test where two subminiature six-component load cells were installed in each Solid Rocket Booster (SRB) to acquire forces and moments for each SRB separately from the full vehicle forces and moments measured by the main strain gauge balance. Finally, sample results from the experiment are presented including improved overall data coverage, evaluation of the new SRB data, and smoke flow visualization photos.

Chan, David T.↗
NASA NTRSDate not supplied

Leveraging Large Eddy Simulations to Characterize Aeroacoustic Environments on Launch Vehicles

NASA's Space Launch System (SLS) program has relied on multiple wind tunnel campaigns to predict expected aeroacoustic environments. Time, cost, Reynolds number matching, contamination from test section acoustics, and limitations in spatial resolution are all factors that impact the use experimental data for development of launch vehicle environments. Methodological and computational advances over the last decade are enabling scale resolving computational fluid dynamics (CFD) simulations to be completed that can address some the challenges with conventional datasets, enabling more complete/accurate modeling of dynamic loading events on ascent. These simulations are classified as so-called "Large-Eddy Simulations" (LES). As the name implies, these simulations seek to directly resolve the turbulence in the largest, most-energetic turbulent structures, or eddies, and the dissipation of the smallest eddies in the flow field, is modeled. Like anything else, these simulations still must undergo rigorous testing and validation for the results to ultimately be trusted in the analysis of a launch vehicle. EV33 has begun to conduct some of this early-stage testing and validation to better support NASA missions in the future.

Jonathan Boustani↗
NASA NTRS2012

Fluorescence-Doped Particles for Simultaneous Temperature and Velocity Imaging

Polystyrene latex microspheres (PSLs) have been used for particle image velocimetry (PIV) and laser Doppler velocimetry (LDV) measurements for several decades. With advances in laser technologies, instrumentation, and data processing, the capability to collect more information about fluid flow beyond velocity is possible using new seed materials. To provide additional measurement capability, PSLs were synthesized with temperature-sensitive fluorescent dyes incorporated within the particle. These multifunctional PSLs would have the greatest impact if they could be used in large scale facilities with minimal modification to the facilities or the existing instrumentation. Consequently, several potential dyes were identified that were amenable to existing laser systems currently utilized in wind tunnels at NASA Langley Research Center as well as other wind and fluid (water) tunnels. PSLs incorporated with Rhodamine B, dichlorofluorescein (DCF, also known as fluorescein 548 or fluorescein 27) and other dyes were synthesized and characterized for morphology and spectral properties. The resulting particles were demonstrated to exhibit fluorescent emission, which would enable determination of both fluid velocity and temperature. They also would allow near-wall velocity measurements whereas laser scatter from surfaces currently prevents near-wall measurements using undoped seed materials. Preliminary results in a wind tunnel facility located at Virginia Polytechnic Institute and State University (Virginia Tech) have verified fluorescent signal detection and temperature sensitivity of fluorophore-doped PSLs.

Danehy, Paul M.↗
NASA NTRS1983

Reattaching turbulent shear layers with perturbed structure

The reattachment of a fully turbulent, two-dimensional shear layer downstream of a backward-facing step has been studied experimentally. The work examines the effect of modifications in shear layer structure upstream of reattachment. A series of experiments were conducted in a low-speed wind tunnel using specialized instrumentation suited to the highly turbulent, reversing flow near reattachment. Accurate characterization of the time-mean features of the reattaching flows was possible. Assuming linear scaling normalized on distance from reattachment, distributions of the normalized pressure coefficients, the time-averaged skin friction coefficient, and the forward flow fraction appear universal for two-dimensional reattachment, independent of initial conditions and steep height, for given duct geometry (area ratio) and for high step height Reynolds numbers. The results suggest universal flow structure in the reattachment zone.

Westphal, R. V.↗
NASA NTRS1984

Effect of initial conditions on turbulent reattachment downstream of a backward-facing step

The reattachment of a fully turbulent, two-dimentional shear layer downstream of a backward-facing step has been studied experimentally. The work examines the effect of variations in inlet conditions on the process of reattachment. A series of experiments was conducted in a low-speed wind tunnel using specialized instrumentation suited to the highly turbulent reversing flow near reattachment. Accurate characterization of the time-mean features of the reattaching flows was possible. Assuming linear scaling normalized on distance from reattachment, distributions of normalized pressure coefficient and forward flow fraction, and time-averaged skin friction coefficient appear universal for two-dimensional reattachment, independent of initial conditions and step height, for given duct geometry (area ratio) and for high step-height Reyolds numbers with thin separating boundary layers. The results suggest universal flow structure in the reattachment zone.

Westphal, R. V.↗
NASA NTRS1988

Payload bay atmospheric vent airflow testing at the Vibration and Acoustic Test Facility

Several concerns related to venting the Space Shuttle Orbiter payload bay during launch led to laboratory experiments with a flight-type vent box installed in the wall of a subsonic wind tunnel. This report describes the test setups and procedures used to acquire data for characterization of airflow through the vent box and acoustic tones radiated from the vent-box cavity. A flexible boundary-layer spoiler which reduced the vent-tone amplitude is described.

Johnston, James D., Jr.↗
NASA NTRS2003

UAV Flight Control Using Distributed Actuation and Sensing

An array of effectors and sensors has been designed, tested and implemented on a Blended Wing Body Uninhabited Aerial Vehicle (UAV). This UAV is modified to serve as a flying, controls research, testbed. This effectorhensor array provides for the dynamic vehicle testing of controller designs and the study of decentralized control techniques. Each wing of the UAV is equipped with 12 distributed effectors that comprise a segmented array of independently actuated, contoured control surfaces. A single pressure sensor is installed near the base of each effector to provide a measure of deflections of the effectors. The UAV wings were tested in the North Carolina State University Subsonic Wind Tunnel and the pressure distribution that result from the deflections of the effectors are characterized. The results of the experiments are used to develop a simple, but accurate, prediction method, such that for any arrangement of the effector array the corresponding pressure distribution can be determined. Numerical analysis using the panel code CMARC verifies this prediction method.

Barnwell, William G.↗
NASA NTRS2003

Distributed Actuation and Sensing on an Uninhabited Aerial Vehicle

An array of effectors and sensors has been designed, tested and implemented on a Blended Wing Body Uninhabited Aerial Vehicle (UAV). The UAV is modified to serve as a flying, controls research, testbed. This effector/sensor array provides for the dynamic vehicle testing of controller designs and the study of decentralized control techniques. Each wing of the UAV is equipped with 12 distributed effectors that comprise a segmented array of independently actuated, contoured control surfaces. A single pressure sensor is installed near the base of each effector to provide a measure of deflections of the effectors. The UAV wings were tested in the North Carolina State University Subsonic Wind Tunnel and the pressure distribution that result from the deflections of the effectors are characterized. The results of the experiments are used to develop a simple, but accurate, prediction method, such that for any arrangement of the effector array the corresponding pressure distribution can be determined. Numerical analysis using the panel code CMARC verifies this prediction method.

Barnwell, William Garrard↗
NASA NTRS1998

Computational Analysis of Shock Layer Emission Measurements in an Arc-Jet Facility

This paper reports computational analysis of radiation emission experiments in a high enthalpy arc-jet wind tunnel at NASA Ames Research Center. Recently, as part of ongoing arc-jet characterization work, spectroscopic radiation emission experiments have been conducted at the 20 MW NASA Ames arc-jet facility. The emission measurements were obtained from the arc-jet freestream and from a shock layer formed in front of flatfaced models. Analysis of these data is expected to provide valuable information about the thermodynamic state of the gas in the arc-jet freestream and in the shock layer as well as thermochemical equilibration processes behind the shock in arc-jet flows. Knowledge of the thermodynamic state of the gas in arc-jet test flows and especially within the shock layer is essential to interpret the heat transfer measurements such as in surface catalysis experiments. The present work is a continuation of previous work and focuses on analysis of the emission data obtained at relatively low-pressure conditions for which the arc-jet shock layer is expected to be in thermal and chemical nonequilibrium. Building blocks of the present computational analysis are: (1) simulation of nonequilibrium expanding flow in the converging-diverging conical nozzle and supersonic jet; (2) simulation of nonequilibrium shock layer formed in front of the flat-faced cylinder model; and (3) prediction of line-of-sight radiation from the computed flowfield. For computations of the nonequilibrium flow in the conical nozzle and shock layer, multi-temperature nonequilibrium codes with the axisymmetric formulation are used. For computations of line-of-sight radiation. a nonequilibrium radiation code (NEQAIR) is used to predict emission spectra from the computed flowfield. Computed line-of-sight averaged flow properties such as vibrational and rotational temperatures, species number densities within the shock layer will be compared with those deduced from the experimental spectra. Detailed comparisons of computational and experimental spectra will also be presented.

Gokcen, Tahir↗