Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMPRESSIBILITY EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

Control of shock-wave boundary-layer interactions by bleed in supersonic mixed compression inlets

An experimental investigation has been conducted to determine the effect of bleed region geometry and bleed rate on shock wave-boundary layer interactions in an axisymmetric, mixed-compression inlet at a Mach number of 2.5. The full realizable reduction in transformed form factor is obtained by bleeding off about half the incident boundary layer mass flow. Bleeding upstream or downstream of the shock-induced pressure rise is preferable to bleeding across the shock-induced pressure rise. Slanted holes are more effective than normal holes. Two different bleed hole sizes were tested without detectable difference in performance.

Fukuda, M. K.↗

Transport Coefficients in weakly compressible turbulence

A theory of transport coefficients in weakly compressible turbulence is derived by applying Yoshizawa's two-scale direct interaction approximation to the compressible equations of motion linearized about a state of incompressible turbulence. The result is a generalization of the eddy viscosity representation of incompressible turbulence. In addition to the usual incompressible eddy viscosity, the calculation generates eddy diffusivities for entropy and pressure, and an effective bulk viscosity acting on the mean flow. The compressible fluctuations also generate an effective turbulent mean pressure and corrections to the speed of sound. Finally, a prediction unique to Yoshizawa's two-scale approximation is that terms containing gradients of incompressible turbulence quantities also appear in the mean flow equations. The form these terms take is described.

Rubinstein, Robert↗

Type Ia supernovae deflagration-to-detonation transition explosions powered by the Zel’dovich reactivity gradient mechanism

ABSTRACT Our aim in this work is to identify and explain the necessary conditions required for an energetic explosion of a Chandrasekhar-mass white dwarf. We construct and analyse weakly compressible turbulence models with nuclear burning effects for carbon/oxygen plasma at a density expected for the deflagration-to-detonation transition (DDT) to occur. We observe the formation of carbon deflagrations and transient carbon detonations at early times. As turbulence becomes increasingly inhomogeneous, sustained carbon detonations are initiated by the Zel’dovich reactivity gradient mechanism. The fuel is suitably preconditioned by the action of compressive turbulent modes with wavelength comparable to the size of resolved turbulent eddies; no acoustic wave is involved in this process. Oxygen detonations are initiated, aided either by reactivity gradients or by collisions of carbon detonations. The observed evolutionary time-scales are found to be sufficiently short for the above process to occur in the expanding, centrally ignited massive white dwarf. The inhomogeneous conditions produced prior to the DDT might be of consequence for the chemical composition of the outer ejecta regions of Type Ia supernovae from the single degenerate channel, and offer the potential for validation of the proposed model.

Brooker, E.↗

Assessing the Long-Term Stability of Anion Exchange Membranes for Electrochemical CO 2 Reduction

Materials and cell components used in CO 2 electrolysis have largely been adapted from technologies initially developed for water electrolysis and fuel cells. However, electrochemical CO 2 reduction introduces distinct material challenges due to the unique chemical environment in this process. Here, in this study, we conducted ex-situ 1000 h stability tests on commonly used anion exchange membranes, exposing them exclusively to electrolytes and organic molecules used or produced during CO 2 electrolysis, at concentrations relevant to and compatible with postseparation processes. Notably, 15% w/w n-propanol and 5 M acetic acid caused complete dissolution or partial disintegration of the membranes unless cross-linking was present and remained stable throughout the test. When the membranes stayed physically intact, most of them exhibited excellent chemical stability in alkaline medium containing alcohols or formic acid, which was confirmed by vibrational spectroscopy and ion exchange capacity measurements. However, exposure to alcohol-and acid-containing solutions led to a substantial increase in swelling and water uptake, with potential implications for mechanical stability, ion/product crossover, and compression management of adjacent components. The potential effects of CO 2 electroreduction products on membrane stability, their subsequent impact on electrolyzer performance, and mitigation strategies are discussed.

CO2RR↗

Pressure-induced quenching of the charge-density-wave state observed by x-ray diffraction

We report an x-ray diffraction study on the charge-density-wave (CDW) LaTe{sub 3} and CeTe{sub 3} compounds as a function of pressure. We extract the lattice constants and the CDW modulation wave-vector, and provide direct evidence for a pressure-induced quenching of the CDW phase. We observe subtle differences between the chemical and mechanical compression of the lattice. We account for these with a scenario where the effective dimensionality in these CDW systems is dependent on the type of lattice compression and has a direct impact on the degree of Fermi surface nesting and on the strength of fluctuation effects.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Failure analysis of thick composite cylinders under external pressure

Failure of thick section composites due to local compression strength and overall structural instability is treated. Effects of material nonlinearity, imperfect fiber architecture, and structural imperfections upon anticipated failure stresses are determined. Comparisons with experimental data for a series of test cylinders are described. Predicting the failure strength of composite structures requires consideration of stability and material strength modes of failure using linear and nonlinear analysis techniques. Material strength prediction requires the accurate definition of the local multiaxial stress state in the material. An elasticity solution for the linear static analysis of thick anisotropic cylinders and rings is used herein to predict the axisymmetric stress state in the cylinders. Asymmetric nonlinear behavior due to initial cylinder out of roundness and the effects of end closure structure are treated using finite element methods. It is assumed that local fiber or ply waviness is an important factor in the initiation of material failure. An analytical model for the prediction of compression failure of fiber composites, which includes the effects of fiber misalignments, matrix inelasticity, and multiaxial applied stresses is used for material strength calculations. Analytical results are compared to experimental data for a series of glass and carbon fiber reinforced epoxy cylinders subjected to external pressure. Recommendations for pretest characterization and other experimental issues are presented. Implications for material and structural design are discussed.

Caiazzo, A.↗

Plasma-based Accelerator with Magnetic Compression

Electron dephasing is a major gain-inhibiting effect in plasma-based accelerators. A novel method is proposed to overcome dephasing, in which the modulation of a modest (~$\mathcal{O}$(10 kG)), axial, uniform magnetic field in the acceleration channel leads to densification of the plasma through magnetic compression, enabling direct, time-resolved control of the plasma wave properties. The methodology is broadly applicable and can be optimized to improve the leading acceleration approaches, including plasma beat-wave, plasma wakefield, and laser wakefield acceleration. The advantages of magnetic compression compared to other proposed schemes to overcome dephasing are identified.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Design of bunch compressing system with suppression of coherent synchrotron radiation for ATF upgrade

One of the operation modes for Accelerator Test Facility (ATF) upgrade is to provide high peak current, high quality electron beam for users. Such operation requires a bunch compressing system with a very large compression ratio. The CSR originating from the strong compressors generally could greatly degrade the quality of the electron beam. In this paper, we present our design for the entire bunch compressing system that will limit the effect of CSR on the e-beam’s quality. We discuss and detail the performance from the start to end simulation of such a compressor for ATF.

43 PARTICLE ACCELERATORS↗

Influence of set retarding admixtures on calcium sulfoaluminate cement hydration and property development

Little published data is available to guide specification calcium sulfoaluminate cement (CSA) mixtures with citric acid retarder dosage rates capable of achieving adequate field working times, nor to understand the effect of retarder dosage on hydration and property development, representing a significant barrier to widespread CSA concrete use. Thus, this study investigated the use of citric acid with two commercially-available CSA cements, tracking the effects of dosage on phase development, hydration, setting, and compressive strengths. Key findings were that: citric acid successfully retarded initial set past 120 min for both cements despite significantly different chemistries; increasing cement anhydrite content reduced retarder effectiveness and altered hardened binder microstructure, reducing compressive strengths; greater retarder dosages did not negatively affect cumulative hydration, nor strengths; and the time at which the maximum rate of heat evolution occurred correlated with final setting, a relationship useful for predicting field mixture behavior based on laboratory testing.

36 MATERIALS SCIENCE↗

Experimental Study of Deformation and of Effective Width in Axially Loaded Sheet-stringer Panels

The deformation of two sheet-stringer panels subjected to end compression under carefully controlled end conditions was measured at a number of points and at a number of loads, most of which were above the load at which the sheet had begun to buckle. The two panels were identical except for the sheet, which was 0.70-inch 24st alclad for specimen 1 and 0.025-inch 24st aluminum alloy for specimen 6. A technique was developed for attaching Tuckerman optical strain gauges to the sheet without disturbing the strain distribution in the sheet by the method of attachment. This technique was used to explore the strain distribution in the sheet at various loads. The twisting and the bending of the stringers was measured by means of pointers attached to the stringers. The shape of the buckles in the sheet of specimen 6 was recorded at two loads by means of plaster casts. The sheet and the stringer loads at failure are compared with the corresponding loads for five similar panels tested at the Navy Model Basin. A detailed comparison is made between the measured deformation of the buckled sheet and the deformation calculated from approximate theories for the deformation in a rectangular sheet with freely supported edges buckling under end compression advanced by Timoshenko, Frankland, and Marguerre. The measured effective width for the specimens is compared with the effective width given by nine different relations for effective width as a function of the edge stress divided by the buckling stress of the sheet. The analysis of the measured stringer deformation is confined to an application of Southwell's method of plotting deformation against deformation over load. It was concluded that the stringer failure in both specimens were due to an instability in which the stringer was simultaneously twisted and bent as a column.

FORMULAS - BUCKLING - KARMAN↗

A study on fatigue crack growth behavior subjected to a single tensile overload: Part II. Transfer of stress concentration and its role in overload-induced transient crack growth

The combined effects of overload-induced enlarged compressive residual stresses and crack tip blunting with secondary cracks are suggested to be responsible for the observed changes in the crack opening load and resultant post-overload transient crack growth behavior [Lee SY, Liaw PK, Choo H, Rogge RB, Acta Mater 2010;59:485-94]. In this article, in situ neutron diffraction experiments were performed to quantify the influence of the combined effects by investigating the internal-stress evolution at various locations away from the crack tip. In the overload-retardation period, stress concentration occurs in the crack blunting region (an overload point) until a maximum crack arrest load is reached. The stress concentration is then transferred from the blunting region to the propagating crack tip (following the overload), requiring a higher applied load, as the closed crack is gradually opened. The transfer phenomena of the stress concentration associated with a crack opening process account for the nonlinearity of strain response in the vicinity of the crack tip. The delaying action of stress concentration at the crack tip is understood in conjunction with the concept of a critical stress (i.e. the stress required to open the closed crack behind the crack tip). A linear relationship between {Delta}{var_epsilon}{sub eff} and {Delta}K{sub eff} provides experimental support for the hypothesis that {Delta}K{sub eff} can be considered as the fatigue crack tip driving force.

36 MATERIALS SCIENCE↗

Hysteresis and Kinetic Effects During Liquid-Solid Transitions

We address the fundamental issue of phase transition kinetics in dynamically compressed materials. Focusing on solid bismuth (Bi) as a prototype material, we used a variety of time-resolved experiments including electrical conductivity and velocimetry to study the phase transition kinetics of the solid-solid phase transitions. Simple single shock experiments performed on several low-lying high pressure phases of Bi, revealed surprisingly complex behavior and slow dynamics. Strong hysteresis effects were observed in the transition behavior in experiments where the compressed Bi was allowed to release back across a phase line. These experiments represent the first reported simultaneous use of resistivity and velocimetry in a shock compression experiment, and the first observation of hysteresis effects occurring during dynamic compression and release.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural characteristics and elevated temperature mechanical properties of AJ62 Mg alloy

Structure and mechanical properties of the novel casting AJ62 (Mg–6Al–2Sr) alloy developed for elevated temperature applications were studied. The AJ62 alloy was compared to commercial casting AZ91 (Mg–9Al–1Zn) and WE43 (Mg–4Y–3RE) alloys. The structure was examined by scanning electron microscopy, x-ray diffraction and energy dispersive spectrometry. Mechanical properties were characterized by Viskers hardness measurements in the as-cast state and after a long-term heat treatment at 250 °C/150 hours. Compressive mechanical tests were also carried out both at room and elevated temperatures. Compressive creep tests were conducted at a temperature of 250 °C and compressive stresses of 60, 100 and 140 MPa. The structure of the AJ62 alloy consisted of primary α-Mg dendrites and interdendritic nework of the Al{sub 4}Sr and massive Al{sub 3}Mg{sub 13}Sr phases. By increasing the cooling rate during solidification from 10 and 120 K/s the average dendrite arm thickness decreased from 18 to 5 μm and the total volume fraction of the interdendritic phases from 20% to 30%. Both factors slightly increased hardness and compressive strength. The room temperature compressive strength and hardness of the alloy solidified at 30 K/s were 298 MPa and 50 HV 5, i.e. similar to those of the as-cast WE43 alloy and lower than those of the AZ91 alloy. At 250 °C the compressive strength of the AJ62 alloy decreased by 50 MPa, whereas those of the AZ91 and WE43 alloys by 100 and 20 MPa, respectively. The creep rate of the AJ62 alloy was higher than that of the WE43 alloy, but significantly lower in comparison with the AZ91 alloy. Different thermal stabilities of the alloys were discussed and related to structural changes during elevated temperature expositions. - Highlights: • Small effect of cooling rate on the compressive strength and hardness of AJ 62 • A bit lower compressive strength of AJ 62 compared to AZ91 at room temperature • Higher resistance of the AJ 62 alloy to the creep process in compression compared to AZ91 • Excellent thermal stability and creep resistance of the alloy WE 43 • Improved thermal stability and creep resistance in order WE43 > AJ62 >> AZ91.

36 MATERIALS SCIENCE↗

Aerodynamics and Aeroacoustic Sources of a Coaxial Rotor

Vehicles with coaxial, contra-rotating rotor systems (CACR) are being considered for a range of applications. Design parameters are identified that effect the fundamental aerodynamics and fluid dynamic features of a CACR in hover, vertical, and edgewise flight. Understanding the fluid dynamic features is a precursor to studying the aeroacoustics of a coaxial rotor. Rotor performance was computed initially using Navier-Stokes solver with prescribed blade section aerodynamic properties, the results validated against generic experimental test cases. Using a A 2D potential flow code and 2D OVERFLOW compressible-flow Navier-Stokes solver, the fluid dynamics of blade interactions was simplified and broken into a 2D blade crossing problem, with crossing locations and velocity fields from the rotor results to understand circulation, thickness, compressibility, shed vorticity, downwash, and viscosity effects. A calculation tool has been developed to identify time and location of blade overlap and BVI time location for CACR. Specific aerodynamic phenomena that occur for each noise source relevant to CACR are presented, along with computational tools to predict these occurrences.

Aeroacoustic↗

Nonlinear Fast Magnetosonic Waves in Solar Prominence Pillars

We investigate the properties of nonlinear fast magnetosonic (NFM) waves in a solar prominence, motivated by recent high-resolution and high-cadence Hinode/SOT observations of small-scale oscillations in a prominence pillar. As an example, we analyze the details of the 2012 February 14 Hinode/SOT observations of quasi-periodic propagating features consistent with NFM waves, imaged in emission in Ca II and in the far blue wing of Hα. We perform wavelet analysis and find oscillations in the 1-3 min period range. Guided by these observations, we model the NFM waves with a three-dimensional magnetohydrodynamics (3D MHD) model, extending previous 2.5D MHD studies. The new model includes the structure of the high-density, low-temperature material of the prominence pillar embedded in the hot corona, in both potential and non-force-free sheared magnetic field configurations. The nonlinear model demonstrates the effects of mode coupling and the propagating density compressions associated with linear and NFM waves. The guided fast magnetosonic waves, together with density compressions and currents, are reproduced in the 3D pillar structure. We demonstrate or the first time the dynamic effects of the Lorentz force due to the magnetic shear in the non-force-free field on the pillar structure and on the propagation of the waves. The insights gained from the 3D MHD modeling are useful for improving coronal seismology of prominence structures that exhibit fast MHD wave activity.

Leon Ofman↗

Understanding Phase and Interfacial Effects of Spall Fracture in Additively Manufactured Ti-5Al-5V-5Mo-3Cr

Additive manufactured Ti-5Al-5V-5Mo-3Cr (Ti-5553) is being considered as an AM repair material for engineering applications because of its superior strength properties compared to other titanium alloys. Here, we describe the failure mechanisms observed through computed tomography, electron backscatter diffraction (EBSD), and scanning electron microscopy (SEM) of spall damage as a result of tensile failure in as-built and annealed Ti-5553. We also investigate the phase stability in native powder, as-built and annealed Ti-5553 through diamond anvil cell (DAC) and ramp compression experiments. We then explore the effect of tensile loading on a sample containing an interface between a Ti-6Al-V4 (Ti-64) baseplate and additively manufactured Ti-5553 layer. Post-mortem materials characterization showed spallation occurred in regions of initial porosity and the interface provides a nucleation site for spall damage below the spall strength of Ti-5553. Preliminary peridynamics modeling of the dynamic experiments is described. Finally, we discuss further development of Stochastic Parallel PARticle Kinteic Simulator (SPPARKS) Monte Carlo (MC) capabilities to include the integration of alpha (α)-phase and microstructural simulations for this multiphase titanium alloy.

36 MATERIALS SCIENCE↗

A fully integrated 3D CFD model of the flow and heat transfer in a packed bed reactor - 18578

The physical phenomena associated with the modes of heat transfer within a packed pebble bed can be modelled by explicitly solving the associated partial differential equations using a finite volume method approach. Convection from the spheres to coolant, conduction inside and between spheres as well as radiation between various components of a packed bed reactor are the main modes of heat transfer, with several lesser, albeit contributing, phenomena also present. Advances both in software and computing power allow for a larger portion of a packed bed to be modeled with greater accuracy by integrating all applicable physics models in one simulation. A representative unstructured packed bed of uniform spheres was generated with a discrete element method (DEM) and the flow domain modelled using the CFD software package Star-CCM+, taking into account all primary modes of heat transfer as well as a user-specified approach to take secondary effects into account. Effects in the bulk, near-wall and wall-contact regions were investigated. By using such a fully integrated explicit model, a deeper understanding can be can be gained into the role of the underlying phenomena and their respective contributions to the overall heat transfer process. Fuel spheres were modeled explicitly with the conduction between spheres, bed and reflectors being prescribed by contact heat transfer theory as a function of temperature and compressive forces within the bed. The effective thermal conductivity (k{sub eff}), flow pressure drop, as well as temperature distributions in the spheres and coolant were calculated and compared with experimental results from published literature. Good agreement was found with experimental results and the significant contribution of radiation as well as inter-pebble conduction to the effective thermal conductivity could be observed from the results. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Refine your search to explore more results.