Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dislocation structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

Collaborative atomic-scale design, analysis, and nanofabrication for record breaking, single-crystal Zn(x)Cd(1-x)Te solar cell arrays

Cadmium telluride (CdTe) based photovoltaics provide a viable solar energy solution because of their short payback time, low manufacturing cost, and high theoretical efficiency ~29%. However, the highest record laboratory efficiency is only 22.1% and long-term performance degradation is ~1 % per year which hinders greater economic viability. Higher open circuit voltage (Voc) and fill factor (FF) are needed to increase the efficiency of the solar cell. Cells with record energy conversion efficiencies report short current (Jsc) values close to their theoretical maximum. However, Voc and FF in these devices remain well below their anticipated optimum. These electrical parameters depend on the quality of the various layers in the solar cell. In particular they depend on the crystalline quality including the defect and impurity concentrations. Therefore understanding how defects and impurities form and evolve in the material layers is important to design devices with higher efficiency and stability. The aim of this project is to create a novel path around the fundamental barriers to achieve high open-circuit voltages (VOC ≥ 1.0 V) in CdTe/CdS solar cells. The idea of the project was to combine nanopatterned crystal growth and alloy compositional grading (with concomitant lattice parameter and energy band gap grading) to reduce the defect density and dramatically improve spatial uniformity of ZnxCd(1-x)Te/CdS cells. The lattice mismatch between ZnTe and CdS is 3.9% compared to a much larger 9.2% between CdTe and CdS. Importantly, when crystal growth is contained to the nanoscale, the strain in each layer is reduced by a factor of two due to strain partitioning and 3D strain relief mechanisms that come into play. This reduces the strain in the ZnTe from 3.9% to 1.95% which is within the range of metamorphic crystal growth. In preliminary studies, molecular dynamics simulation of ZnTe/CdS islands predicted dislocation-free material when the patterning was reduced to ~80 nm in diameter. The energy band gap of ZnxCd(1-x)Te is also graded in conjunction with alloy composition. ZnTe has an energy band gap of 2.3 eV. Finally, an added benefit of patterned growth is that it enables direct one-to-one study of the relationships between fabrication, microstructure and performance of individual crystal grains within the array. Experimental characterization techniques such as atomic probe tomography (APT) and transmission electron microscopy (TEM) have elucidated much about the microstructure of the layers. However, the techniques are destructive, costly and have limitations on the information they convey. For example, TEM gives information with atomic scale resolution but on 2-dimensional substrates. On the other hand, APT gives 3-dimensional information but is not able to resolve atomic scale structure. Alternatively, Molecular Dynamics (MD) simulations offer a solution to rapidly generate time-resolved, 3-dimensional, atomic scale structures of crystal growth. Direct MD simulations of microstructures of Cu-doped II-VI compound multilayers can impact the research on CdTe/CdS solar cells. Such MD simulations require an interatomic potential database that includes at least four elements Cu, Cd, Te, and S. The Stillinger-Weber (SW) potential is the most widely used interatomic potential for semiconductors. However, while SW potentials have been developed for Ga-In-As-Se-Te, Al-Ga-In-P-As-Sb, Cd-Te-Zn-As-Si, In-Ga-N systems, no potentials existed to simulate Cd-Zn-Hg-Se-S-Te-Cu. The goal of this effort was to fill the knowledge gap by developing a Zn-Cd-Hg-S-Se-Te-Cu SW potential database to enable MD simulations of microstructures of Cu-doped CdTe/CdS solar cells. The new potential was then applied, via MD crystal growth simulations, to study the growth mechanisms and atomic structures of the ZnTe/Cu/CdTe/CdS multilayers under various conditions. The objective of the project was to inform the solar cell community on crystal growth and defect formation at the interface between CdTe-based epilayers grown on CdS substrates. MD simulations offered a unique opportunity to analyze the 3-dimensional crystal growth evolution of Cu doped ZnxCd(1-x)TeyS(1-y) alloys with atomic scale resolution under a variety of conditions. The effect of substrate orientation and polycrystallinity on crystal growth was studied. Substrates with grain boundaries were created and the growth evolution on these substrates were analyzed. Another focus was to elucidate the effect of dopant incorporation on the nature of polycrystallinity crystal growth. Dopants available through the Stillinger-Weber potential developed in this project included Cu, Zn, S, Se, Hg and native vacancies.

14 SOLAR ENERGY↗

Nugget Structure Evolution with Rotation Speed for High-Rotation-Speed Friction-Stir-Welded 6061 Aluminum Alloy

High-rotation-speed friction stir welding (HRS-FSW) is a promising technique to reduce the welding loads during FSW and thus facilitates the application of FSW for in situ fabrication and repair. In this study, 6061 aluminum alloy was friction stir welded at high-rotation speeds ranging from 3000 to 7000 rpm at a fixed welding speed of 50 mm/min, and the effects of rotation speed on the nugget zone macro- and microstructures were investigated in detail in order to illuminate the process features. Temperature measurements during HRS-FSW indicated that the peak temperature did not increase consistently with rotation speed; instead, it dropped remarkably at 5000 rpm because of the lowering of material shear stress. The nugget size first increased with rotation speed until 5000 rpm and then decreased due to the change of the dominant tool/workpiece contact condition from sticking to sliding. At the rotation speed of 5000 rpm, where the weld material experienced weaker thermal effect and higher-strain-rate plastic deformation, the nugget exhibited relatively small grain size, large textural intensity, and high dislocation density. Consequently, the joint showed superior nugget hardness and simultaneously a slightly low tensile ductility.

36 MATERIALS SCIENCE↗

New intrinsic mechanism on gum-like superelasticity of multifunctional alloys

Ti-Nb-based Gum Metals exhibit extraordinary superelasticity with ultralow elastic modulus, superior strength and ductility, and a peculiar dislocation-free deformation behavior, most of which challenge existing theories of crystal strength. Additionally, this kind of alloys actually displays even more anomalous mechanical properties, such as the non-linear superelastic behavior, accompanied by a pronounced tension-to-compression asymmetry, and large ductility with a low Poisson’s ratio. Two main contradictory arguments exist concerning the deformation mechanisms of those alloys, i.e., formation of reversible nanodisturbance and reversible martensitic transformation. Herein we used the in-situ synchrotron high-energy X-ray scattering technique to reveal the novel intrinsic physical origin of all anomalous mechanical properties of the Ti-24Nb-4Zr-8Sn-0.10O alloy, a typical gum-like metal. Our experiments provide direct evidence on two different kinds of interesting, stress-induced, reversible nanoscale martensitic transitions, i.e., the austenitic regions with B2 structure transform to a0 martensite and those with BCC structure transform to d martensite.

COMPUTATIONAL METHODS↗

Depth-dependent ordering, two-length-scale phenomena, and crossover behavior in a crystal featuring a skin layer with defects

Structural defects in a crystal are responsible for the ''two-length-scale'' behavior in which a sharp central peak is superimposed over a broad peak in critical diffuse x-ray scattering. We have previously measured the scaling behavior of the central peak by scattering from a near-surface region of a V{sub 2}H crystal, which has a first-order transition in the bulk. As the temperature is lowered toward the critical temperature, a crossover in critical behavior is seen, with the temperature range nearest to the critical point being characterized by mean-field exponents. Near the transition, a small two-phase coexistence region is observed. The values of transition and crossover temperatures decay with depth. An explanation of these experimental results is here proposed by means of a theory in which edge dislocations in the near-surface region occur in walls oriented in the two directions normal to the surface. The strain caused by the dislocation lines causes the ordering in the crystal to occur as growth of roughly cylindrically shaped regions. After the regions have reached a certain size, the crossover in the critical behavior occurs, and mean-field behavior prevails. At a still lower temperature, the rest of the material between the cylindrical regions orders via a weak first-order transition.

36 MATERIALS SCIENCE↗

Advancing the mechanical integrity and fragmentation behavior of reactive projectiles

A multivariant statistical approach was used to identify treatment conditions that improve the survivability of structural reactive material (SRM) projectiles upon launch and enhance energy release upon impact. The study included both mechanical testing of projectiles as well as their reactive characterization. The projectiles were launched in a high-velocity impact-ignition testing system and impacted an anvil for vented chamber calorimetry. This study examined a link between ultimate compressive stress and combustion performance. Two treatments were applied to consolidated aluminum projectiles including annealing and addition of silica (SiO 2 ) inclusions. Results showed annealing at moderate temperatures resulted in intact SRM projectiles upon launch. Adding small concentrations (1–2 wt. %) of SiO 2 to the SRM promoted fragmentation and combustion performance upon impact. Compared to the untreated projectiles, annealing with SiO 2 inclusion processing treatments improved the energy conversion efficiency from 37–84% (for untreated projectiles) up to 54–98%. In conclusion, increasing interparticle dislocation recovery by annealing while balancing inclusions promoting fragmentation upon impact was the key to optimizing combustion performance for SRM ballistic impact applications.

42 ENGINEERING↗

Dynamics of Helium-Loaded Grain Boundaries under Shear Deformation in α-Fe

The defects produced in collision cascades will interact with microstructural features in materials, such as GBs and dislocations. The coupled motion of GBs under stress has been widely observed in simulations and experiments. Two symmetric tilt GBs with a common <110> tilt axis (Σ3 and Σ11) in bcc iron are used to investigate the coupled motion of GBs under shear deformation. Also, we have explored the effect of self-interstitial atoms (SIAs) loading on the GB motion, with different concentrations of interstitials randomly inserted around the GB plane. The simulation results show that the interstitial loading reduces the critical stress of the GB coupled motion for the Σ3 GB. Furthermore, the interstitials and vacancies are inserted randomly at the GB plane and at a distance of 1 nm away from the GB plane, respectively, to understand the self-healing mechanism of GBs under stress. The behavior of the defect-loaded GBs depends on the GB structure. The loaded interstitials in the Σ3 GB easily form <111> interstitial clusters that do not move along with the GB. The vacancies in the Σ3 GB impede the GB motion. However, the interstitials move along with the Σ11 GB and annihilate with vacancies when the GB moves into the vacancy-rich region, leading to the self-healing and damage recovery of the Σ11 GB.

Gao, Fei↗

Effect of Barothermal Processing on the Solid-State Formation of the Structure and Properties of 16 at % Si–Al Hypereutectic Alloy

We describe barothermal processing (hot isostatic pressing) of a 16 at % Si–Al binary alloy for 3 h at a temperature of 560°C and pressure of 100 MPa for 3 h, in combination with measurements of heat effects during cooling. The results demonstrate that this processing leads to the fragmentation of the silicon structural constituent and ensures a high degree of homogenization of the as-prepared alloy. Heat treatment of the 16 at % Si–Al alloy at 560°C and a pressure of 100 MPa leads to a thermodynamically driven enhanced silicon dissolution, up to ~10 at %, in the aluminum matrix, resulting in the formation of a supersaturated solid solution, which subsequently decomposes during cooling. We analyze the complete porosity elimination process, which makes it possible to obtain a material with 100% relative density. According to differential barothermal analysis, microstructural analysis, and scanning and transmission electron microscopy data, barothermal processing of the 16 at % Si–Al alloy produces a bimodal size distribution of the silicon phase constituent: microparticles 3.6 μm in average size and nanoparticles down to ~1 nm in diameter. The Al matrix has been shown to contain a high density of edge dislocations. Barothermal processing reduces the thermal expansion coefficient and microhardness of the hypereutectic alloy. We conclude that solid-state barothermal processing is an effective tool for completely eliminating microporosity from the 16 at % Si–Al alloy, reaching a high degree of homogenization, and controlling the microstructure of the alloy, in particular by producing high dislocation density in the aluminum matrix.

36 MATERIALS SCIENCE↗

InP- and GaAs-Based 0.6 eV GaInAs Devices for Thermophotovoltaics and Laser Power Conversion

Emerging applications such as thermal energy grid storage, waste heat recovery and portable power generation require efficient thermophotovoltaic (TPV) converters tuned to temperatures near 1000 Degrees Celsius or below. Metamorphic GaInAs with larger lattice constants than InP present a promising option for these needs. The ability to grow these devices on GaAs substrates instead of more expensive InP would enhance the scalability of these devices. In this talk, we present inverted metamorphic Ga0.3In0.7As photovoltaic converters with sub-0.60 eV bandgaps grown on InP and GaAs substrates. These devices are realized using InAsP or GaInP/InAsP compositionally graded buffers which exhibit threading dislocation densities of 1.3 +/- 0.6 x 106 cm-2 and 8.9 +/- 1.7 x 106 cm-2 on InP and GaAs, respectively. Despite this difference in defect density, the devices generate similar open-circuit voltages of 0.386 V and 0.383 V, respectively, under irradiance producing a short-circuit current density of -10 A/cm2, with bandgap-voltage offsets of 0.20 and 0.21 V. We estimate their thermophotovoltaic efficiency using these measurements coupled with broadband reflectance measurments. The InP-based cell is estimated to yield 1.09 W/cm2 at 1100 Degrees Celsius vs. 0.92 W/cm2 for the GaAs-based cell, with TPV efficiencies of 16.8 vs. 9.2%. Both devices are limited by sub-bandgap absorption, which we assess largely occurs in the graded buffers. We estimate that the 1100 Degrees Celsius thermophotovoltaic efficiencies would increase to 24.0% and 20.7% in structures with the graded buffer removed, if previously demonstrated reflectance is achieved. These devices also have application as laser power converters in the 2.0-2.3 um atmospheric window. We estimate efficiencies of 36.8% and 32.5% under 2.0 um monochromatic irradiance of 1.86 W/cm2 and 2.81 W/cm2, respectively.

ENGINEERING,MATERIALS SCIENCE,SOLAR ENERGY↗

Effect of a por-Si Buffer Layer on the Structure and Morphology of Epitaxial In{sub x}Ga{sub 1 – x}N/Si(111) Heterostructures

Integrated heterostructures exhibiting nanocolumnar morphology of the In{sub x}Ga{sub 1 – x}N/Si(111) film are grown on a single-crystal silicon substrate (c-Si(111)) and a substrate with a nanoporous buffer sublayer (por-Si) by molecular-beam epitaxy with the plasma activation of nitrogen. Using a complex of structural and microscopic methods of analysis, it is shown that the growth of In{sub x}Ga{sub 1 – x}N nanocolumns on a nanoporous buffer layer offers a number of advantages over growth on c-Si. The por-Si substrate predetermines the preferential orientation of the growth of In{sub x}Ga{sub 1 – x}N nanocolumns closer to the Si(111) orientation direction and makes it possible to produce In{sub x}Ga{sub 1 – x}N nanocolumns with a higher degree of crystallographic uniformity and with a nanocolumn lateral size of ~40 nm unified over the entire surface. The growth of In{sub x}Ga{sub 1 – x}N nanocolumns on a por-Si layer yields a decrease in the strain components ε{sub xx} and ε{sub zz} and in the density of edge and screw dislocations compared to the corresponding parameters for In{sub x}Ga{sub 1 – x}N nanocolumns grown on c-Si. The In{sub x}Ga{sub 1 – x}N nanocolumnar layer fabricated on por-Si exhibits a 20% higher charge-carrier concentration compared to the layer grown on c-Si as well as a higher intensity of the photoluminescence quantum yield (+25%).

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Evaluation on the Effect of Composition on Radiation Hardening and Embrittlement in Model FeCrAl Alloys

This report details the findings of post-radiation mechanical testing and microstructural characterization performed on a series of model and commercial FeCrAl alloys to assist with the development of a cladding technology with enhanced accident tolerance. The samples investigated include model alloys with simple ferritic grain structure and two commercial alloys with minor solute additions. These samples were irradiated in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL) up to nominal doses of 7.0 dpa near or at Light Water Reactor (LWR) relevant temperatures (300-400 C). Characterization included a suite of techniques including small angle neutron scattering (SANS), atom probe tomography (APT), and transmission based electron microscopy techniques. Mechanical testing included tensile tests at room temperature on sub-sized tensile specimens. The goal of this work was to conduct detailed characterization and mechanical testing to begin establishing empirical and/or theoretical structure-property relationships for radiation-induced hardening and embrittlement in the FeCrAl alloy class. Development of such relationships will provide insight on the performance of FeCrAl alloys in an irradiation environment and will enable further development of the alloy class for applications within a LWR environment. A particular focus was made on establishing trends, including composition and radiation dose. The report highlights in detail the pertinent findings based on this work. This report shows that radiation hardening in the alloys is primarily composition dependent due to the phase separation in the high-Cr FeCrAl alloys. Other radiation induced/enhanced microstructural features were less dependent on composition and when observed at low number densities, were not a significant contributor to the observed mechanical responses. Pre-existing microstructure in the alloys was found to be important, with grain boundaries and pre-existing dislocation networks acting as defect sinks, resulting in variations in the observed microstructures after irradiation. Dose trends were also observed, with increasing radiation dose promoting changes in the size and number density of the Cr-rich α' precipitates. Based on the microstructural analysis, performed tensile testing, and prior knowledge from FeCr literature it was hypothesized that the formation of the Cr-rich α' precipitates could lead to significant radiation-induced embrittlement in the alloys, and this could be composition dependent, a result which would mirror the trends observed for radiation-induced hardening. Due to the limited database on embrittlement in the FeCrAl alloy class after irradiation, a series of radiation experiments have been implemented. The overarching point of view within this report is the radiation tolerance of FeCrAl is complex, with many mechanisms and factors to be considered at once. Further development of the FeCrAl alloy class for enhanced accident tolerant applications requires detailed, single (or at least limited) variable experiments to fully comprehend and predict the performance of this alloy in LWRs. This report has been submitted as fulfillment of milestone M2FT-15OR0202321 titled, Summary report on the effect of composition on the irradiation embrittlement of Gen 1 ATF FeCrAl for the Department of Energy Office of Nuclear Energy, Advanced Fuel Campaign of the Fuel Cycle R&D program.

36 MATERIALS SCIENCE↗

Multiscale and Machine Learning Modeling for Process-informed Microstructure Prediction in Additively Manufactured Materials Using MALAMUTE

Advanced Materials and Manufacturing Technologies (AMMT) program under the Department of Energy Office of Nuclear Energy, aims to develop and qualify additively-manufactured materials for nuclear applications. The key challenges to these efforts are the microstructural variabilities observed on the AM products and their impact on the properties and performance of the material in extreme environments. AMMT is using a combination of high-through-put experimental and modeling techniques to accelerate the qualification efforts. Conventionally, in-situ and ex-situ characterizations and testing are performed to correlate different aspects of the AM process to the final product and its performance. However, adopting a trial-and-error approach to experimentally evaluate the vast range of process parameters required to capture the microstructural variabilities is cost-prohibitive. Modeling and simulation provide a comparatively inexpensive way to understand and correlate the microstructural evolution to the processing conditions. The modeling and simulation work-packages within the AMMT program aims to use physics-based and machine learning modeling capabilities to develop a digital twin for AM that can correlate the process conditions to the final product and establish a process-structure-property-performance (PSPP) correlation for AM materials. The melting and subsequent solidification that occurs during the AM process is a complex phenomenon that requires multiscale multiphysics analysis. Idaho National Laboratory’s (INL) Multiphysics Object-Oriented Simulation Environment (MOOSE), specifically the MOOSE Application Library for Advanced Manufacturing UTilitiEs (MALAMUTE) software, provides an ideal platform for developing the multiphysics multiscale model to explore the intricacies of the microstructural evolution during the AM processes within a single framework. Furthermore, given that such full-fidelity simulations can be computationally intensive, reduced order models are necessary to explore the PSPP space for AM materials in an efficient, reliable, and cost-effective way. This work package focuses on understanding the role of process variabilities on the various microstructural characteristics of the AM materials. Microstructures unique to AM materials, such as compositional micro-heterogeneity and dislocation cells, are of particular interest here since they can influence the creep properties and radiation performance. In fiscal year (FY) 24, we significantly advanced upon our work in the last fiscal year, both on physics-based and ML models. The alloy solidification model available in MOOSE has been extended to incorporate the thermodynamic properties and free energy relevant to 316SS. The model demonstrates the Cr segregation that occurs during solidifcation. It is demonstrated that rate of solidification and solute segregation is primarily influence by the cooling rate dictating the level of freezing. This work captures the microstructural variabilities at the subgrain level that are often missing in the part-scale models. With an aim to connect the microstructural evolution model to realistic process conditions, a reduced order model is developed for predicting the thermal conditions around meltpool from high-fidelity process simulations. Furthermore, machine learning approach is used to accelerate the temperature prediction during the AM process. In the following years, MALAMUTE will be used to connect different aspects of the models and quantitatively predict the microstructural evolution. The developed ML-based surrogate model will consider the process conditions as the input to predict the microstructural features in a cost-effective way. The generated microstructures can be used by other work packages under AMMT to evaluate the properties and environmental response of the material at the mesoscale. Thus, this work help identify the key microstructural features at the subgrain level that are significant in property/performance prediction of the AM products. This work will provide inputs to the large-scale process variability models to reevaluate and validate assumptions/simplifications made in the part-scale models. Furthermore, through active learning this work will help identify the data need from both modeling and experimental sides for development of a robust digital twin for AM.

36 MATERIALS SCIENCE↗

Sub‐0.6 eV Inverted Metamorphic GaInAs Cells Grown on Inp and GaAs Substrates for Thermophotovoltaics and Laser Power Conversion

Abstract Inverted metamorphic Ga 0.3 In 0.7 As photovoltaic converters with sub‐0.60 eV bandgaps grown on InP and GaAs are presented. Threading dislocation densities are 1.3 ± 0.6 × 10 6 and 8.9 ± 1.7 × 10 6 cm −2 on InP and GaAs, respectively. The devices generate open‐circuit voltages of 0.386 and 0.383 V, respectively, under irradiance producing a short‐circuit current density of ≈10 A cm −2 , yielding bandgap‐voltage offsets of 0.20 and 0.21 V. Power and broadband reflectance measurements are used to estimate thermophotovoltaic (TPV) efficiency. The InP‐based cell is estimated to yield 1.09 W cm −2 at 1100 °C versus 0.92 W cm −2 for the GaAs‐based cell, with efficiencies of 16.8 versus 9.2%. The efficiencies of both devices are limited by sub‐bandgap absorption, with power weighted sub‐bandgap reflectances of 81% and 58%, respectively, the majority of which is assumed to occur in the graded buffers. The 1100 °C TPV efficiencies are estimated to increase to 24.0% and 20.7% in structures with the graded buffer removed, if previously demonstrated reflectance is achieved. These devices also have application to laser power conversion in the 2.0–2.3 µm atmospheric window. Peak laser power converter efficiencies of 36.8% and 32.5% are estimated under 2.0 µm irradiances of 1.86 and 2.81 W cm −2 , respectively.

14 SOLAR ENERGY↗

Deuterium trapping mechanisms in reduced activation ferritic martensitic steels and their correlation with mechanical strengthening

Development of high-strength materials often involves introduction of additional strengthening microstructures that also serve as tritium trapping sites. Such additions in fusion material development could degrade the fuel efficiency in fusion reactors and raise radiological concerns. The contribution of individual microstructure features in hydrogen trapping must be evaluated to ensure fuel efficiency and radiological safety. This study explores the mechanistic origins of deuterium trapping in reduced-activation ferritic–martensitic steels and its correlation to mechanical strengthening. A series of model alloys and engineering steels were fabricated and subjected to different heat treatments to control deuterium trapping site density. Deuterium retention was evaluated using D 2 gas charging and thermal desorption spectroscopy, focusing on the role of grain boundary, dislocation, M 23 C 6 precipitates, and TiC precipitates. Multiscale microstructure characterization and synchrotron X-ray diffraction were performed to characterize microstructure, which was correlated to the deuterium retention property. Results show that TiC precipitates exhibit the highest deuterium trapping capacity, followed by M 23 C 6 precipitates. Dislocation and grain boundary demonstrate the lowest and similar efficiencies. Furthermore, the relationship of trapping quantity and mechanical strengthening of these microstructure features was quantified, demonstrating that TiC precipitates offer highest deuterium trapping per unit of mechanical strengthening.

Retention↗

The influence of V-defects, leakage, and random alloy fluctuations on the carrier transport in red InGaN MQW LEDs

Red InGaN-based light-emitting diodes (LEDs) exhibit lower internal quantum efficiencies than violet, blue, and green InGaN LEDs due to a reduction in radiative recombination rates relative to non-radiative recombination rates as the Indium composition increases. Additionally, the larger polarization and band offset barriers between high indium content InGaN quantum wells and GaN quantum barriers increase the forward voltage. In blue and green LEDs, random alloy fluctuations and V-defects play a key role in reducing the forward voltage. When V-defects are present, either naturally or intentionally introduced, they create an alternative path for carrier injection into the MQWs through the V-defect sidewalls. This injection mechanism explains the turn-on voltages of green LEDs. However, in InGaN red LEDs, these two phenomena do not reduce the forward voltage as effectively as in blue and green LEDs, and consequently, the computed forward voltage remains significantly higher than the measured one. Furthermore, currents are observed at low voltages before the turn-on voltage (V<ℏω/e=2.0 V) of red LEDs. To address this, we introduce dislocation-induced tail states in the modeling, suggesting that leakage current through these states may play a significant role both below and at turn-on voltages. The simulation also indicates that leakage carriers below turn-on accumulate, partially diffuse in the QWs, screen the polarization-induced barrier in the low injection regime, and further reduce the forward voltage. Despite these beneficial effects, a drawback of dislocation-induced tail states is the enhanced nonradiative recombination in the dislocation line region. This study provides a detailed analysis of device injection physics in InGaN QW red LEDs and outlines potential optimization strategies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

X-ray diffraction study of short-period AlN/GaN superlattices

The structure of short-period hexagonal GaN/AlN superlattices (SLs) has been investigated by X-ray diffraction. The samples have been grown by metalorganic vapor-phase epitaxy (MOVPE) in a horizontal reactor at a temperature of 1050°C on (0001)Al{sub 2}O{sub 3} substrates using GaN and AlN buffer layers. The SL period changes from 2 to 6 nm, and the thickness of the structure varies in a range from 0.3 to 1 μm. The complex of X-ray diffraction techniques includes a measurement of θ-2θ rocking curves of symmetric Bragg reflection, the construction of intensity maps for asymmetric reflections, a measurement and analysis of peak broadenings in different diffraction geometries, a precise measurement of lattice parameters, and the determination of radii of curvature. The thickness and strain of separate SL layers are determined by measuring the θ-2θ rocking curves subsequent simulation. It is shown that most SL samples are completely relaxed as a whole. At the same time, relaxation is absent between sublayers, which is why strains in the AlN and GaN sublayers (on the order of 1.2 × 10{sup −2}) have different signs. An analysis of diffraction peak half-widths allows us to determine the densities of individual sets of dislocations and observe their change from buffer layers to SLs.

36 MATERIALS SCIENCE↗

Characteristics of martensite transformed from deformed austenite with various states of ultrahigh strength 300 M steel

Highlights: • Fractions of lath martensite and its packets decrease with the increasing of strain. • Length and width of blocks of lath martensite decrease with an increase in strain. • Severe work-hardening and completed DRX hamper transformation of lath martensite. • As for austenite with the state of work-hardening, the lath width changes little. • As for austenite with the state of DRX and subsequent growth, the lath width changes. - Abstract: 300 M steel was isothermally compressed on a Gleeble 1500 simulator at a deformation temperature of 1173 K, a strain rate of 0.1 s{sup −1} and strains ranging from 0.11 to 1.20. The morphologies and structure characteristics of martensite transformed from deformed austenite during water quenching were observed and analysed via scanning electron microscope and transmission electron microscope. Subsequently, effects of prior austenite state on martensitic transformation behavior of 300 M steel were analysed. The experimental results showed that predominant lath martensite and complemental twinned martensite and retained austenite coexisted in deformation-quenched 300 M steel at various strains. The volume fraction of lath martensite and packets of lath martensite decreased with the increasing of strain, and the length and width of the blocks in lath martensite concurrently decreased. Prior austenite with the state of severely work-hardening or just completed dynamic recrystallization would hamper the nucleation and subsequent growth of lath martensite. Additionally, as for austenite with the state of work-hardening, the morphologies and width of laths changed little with the increasing of strain, whereas dislocations in the interior of laths dramatically increased. However, as for austenite with the state of dynamic recrystallization and subsequent growth, the width of laths obviously increased with the increasing of austenite grain size.

36 MATERIALS SCIENCE↗

Characterization of Titanium Alloys Produced by Electron Beam Directed Energy Deposition

Functionally graded materials offer the potential to improve structural efficiency by allowing the material composition and/or microstructural features to spatially vary within a component. Additive manufacturing techniques enable the fabrication of such graded materials and structures. While examining several titanium alloys, this paper focuses on Ti-8Al-1Er as it has a unique microstructure that is only feasible when produced by rapid solidification methods like electron beam directed energy deposition, an additive manufacturing process. The results show that, when mixed, Ti-8Al-1Er and commercially-pure titanium uniformly mix at various ratios and the resultant static tensile properties of the mixed alloys behave according to rule-of-mixtures. At discontinuous interfaces between Ti-8Al-1Er and commercially-pure titanium, the crack growth behavior progresses smoothly across the discontinuity as the crack transitions from one crack growth regime into another. Studies on monolithic samples shows the mechanisms of damage in the Ti-8Al-1Er; specifically, that strain localization occurs near grain boundaries of high mis-orientation on the microscale and that twinning and dislocation density is concentrated near erbia-strengthening particles (Er2O3) on the nanoscale.

Newman, John A.↗

Small uranium and oxygen interstitial clusters in UO 2 : An empirical potential study

The aggregation of defect clusters in UO 2 under irradiations creates dislocation loops and cavities, which in turn contribute to swelling of the fuels, leading to detrimental pellet-clad mechanical interactions. The kinetics of the defect clusters, however, have received less attention and are not well understood. As such, using two interatomic potentials, the Morelon potential and a many-body model by Cooper, Rushton, and Grimes (CRG), the energetics and kinetics of small uranium interstitial clusters, with and without bound oxygen interstitials, are investigated with molecular dynamics and accelerated molecular dynamics simulations. For the single bound anti-Schottky interstitial cluster (U i 2O i ), both potentials find the interstitialcy migration mechanism to be a low barrier migration mechanism. However, for the CRG potential, an oxygen Frenkel pair assisted interstitial cluster migration mechanism with a lower migration barrier is identified during accelerated molecular dynamics simulations. For the Morelon potential, the interstitial clusters have geometrically compact structures, and small interstitial clusters (two and three anti-Schottky clusters) are more mobile than the single bound anti-Schottky interstitial cluster; for the CRG potential, the interstitial clusters have geometrically non-compact structures, yielding a more complex energy landscape. The rapid migration of interstitials and interstitial clusters are important for the irradiation response of UO 2 and correlates well with the very low barriers reported in a few historic experimental studies.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Refine your search to explore more results.