Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES - ELASTICITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

Direct shear strength of rebar-coupler anchor systems for steel-plate composite (SC) walls

This work focuses on the direct shear behavior of rebar-coupler anchor systems, and their use for anchorage of steel-plate composite (SC) walls to the concrete basemat of safety-related nuclear facilities. Large-scale rebar-coupler anchor specimens were tested under direct shear loading until failure. The results included the applied load-slip displacement responses of the specimens, the direct shear strength, and the observed failure mode. The American Concrete Institute (ACI) 349 code equation for calculating the direct shear strength of embedded anchors was compared with the direct shear strengths from the tests. The code equation underestimated the direct shear strength of the anchor system, because it was based on the assumption that shear failure occurs in the rebars, whereas experimental observations indicated that shear fracture failure occurred in the coupler rather than the rebars. The design equation was updated to utilize the net shear area of the coupler instead of the rebars, after which the direct shear strengths from the tests could be calculated with reasonable accuracy. The experimental results were also used to propose an empirical model for the shear force-slip displacement response of rebar-coupler anchor systems.

42 ENGINEERING↗

Impact of Backing Plate and Thermal Boundary Conditions for High-Speed Friction Stir Welding of 25-mm Thick Aluminum Alloy 7175-T79

Here this study demonstrates high-speed (150 mm/min) single pass friction stir butt joining of 25 mm thick aluminum alloy 7175-T79. To understand the impact of quenching and cooling rate on process responses, joint strength, and grain size distributions across the weld thickness, we performed a series of friction stir welding (FSW) trials in air and with a trailing water spray using steel and composite backing plates (BP). Welds made in air and trailing water spray exhibit significantly different hardness distributions across the nugget, heat affected zone (HAZ), and HAZ minimum hardness as evidenced by detailed microhardness mapping. The effect of trailing water spray (TWS) on joint efficiency overshadows the influence of BP composition due to the vastly different contribution to quenching. TWS also resulted in a multifaceted effect on FSW such as lowering processing temperature, increasing X and Z forces while lowering Y force, and narrow heat affecting zone. Finally, digital image correlation (DIC)-based fracture mode analysis and grain size measurements correlate with the hardness distribution.

42 ENGINEERING↗

Experimental and Numerical Investigation on Vibration of Sandwich Plates with Honeycomb Cores Based on Radial Basis Function

The vibration characteristic of the sandwich plate with a honeycomb core was investigated by experimental measurements and numerical calculation based on radial basis function (RBF). RBF method was used not only in the meshless approach but also in the post-processing of the experimental data. During the experiment, amplitude-fluctuation electronic speckle pattern interferometry was applied to access the resonant frequencies and the corresponding vibration mode shapes simultaneously. Then RBF method was used to improve the quality of patterns and reconstruct the out-of-plane vibration amplitude after fringe analysis. As for numerical calculation, the modal parameters were numerically predicted using the first-order shear deformation theory. The computation approach was based on collocation with multi-quadric radial basis function. To understand the influence of the thickness of face sheet on dynamic behaviors, three types of specimens with different thickness were tested and analyzed. Of particular interest was that the vibration modes show veering due to the thickness increment. Furthermore, the numerical predicted results were compared with the experimental measurements for the first five modes. They are in good agreement with each other for resonant frequencies, mode shapes and relative out-of-plane amplitudes.

36 MATERIALS SCIENCE↗

Numerical and Analytical Analysis of Thin Laser-Driven Flyer Plates

Computational and analytical investigations have been performed for laser-driven flyer plate experiments and compared with data. These have resulted in a more fundamental understanding of the physical processes in the laser absorption, and acceleration of the flyers by the expansion of laser produced plasma. The analytical work describes the dependences of final foil velocity, while the computational simulations permit a detailed look at energy coupling and foil acceleration issues.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

A novel PEMEC with 3D printed non-conductive bipolar plate for low-cost hydrogen production from water electrolysis

For establishing the large-scale hydrogen production as energy carrier from water electrolysis, improving cost-effectiveness and efficiency remains the main challenges. In this study, we propose a novel proton exchange membrane electrolyzer cell (PEMEC), consisting of non-conductive bipolar plates (BPs) and thin film liquid/gas diffusion layers (TF-LGDLs) to reduce the cost and improve the PEMEC performance. The 3D printed non-conductive BP is manufactured with low-cost polylactic acid (PLA) and is mainly functioned to distribute the water and gas products. A titanium thin film LGDL (TF-LGDL) with surroundings is developed for directly transporting electrons from the external power sources, which changes the electron transport path in the PEMECs. The PLA BP exhibits an extremely low cost (1/10 of that of the graphite BP), and the hydrogen production rate per unit BP cost in a PEMEC with PLA BP, is almost 6 times higher than a conventional one with graphite BPs. More importantly, the PEMECs with PLA BPs can achieve a good electrochemical performance of 2.21 V at 1 A/cm 2 under room temperature. A model is also developed to investigate the impact of the BP resistivity of on the cell performance, and a guideline for the selection guideline of conductivity of BPs material is provided. The easily accessible and low-cost PLA BPs coupled with the new electron-conducting path will drive the exploration of plastic materials for economic and efficient water splitting or other energy conversion devices, including fuel cells, batteries, and solar cells.

09 BIOMASS FUELS↗

Formation of Coanda jet from sharp-edged swirl nozzle with base plate

Experiments were conducted using tufts and PIV to determine the conditions for which a swirled gas jet issuing from a sharp-edge nozzle, in flush with a base plate, would form a Coanda jet. The flow field was also simulated. The inception of the Coanda jet was observed to be associated with the formation of a recirculation bubble at the nozzle exit. A threshold value of swirl number, which increased monotonically with Reynolds number, was required for the formation of the Coanda jet. The Coanda jet was associated with hysteresis. The flow features and transition from a diverging jet to a Coanda jet are discussed. (author)

42 ENGINEERING↗

Bipolar plate development with additive manufacturing and protective coating for durable and high-efficiency hydrogen production

Additive manufacturing (AM) of the complex devices for energy application remains an almost unexplored area, and the harsh acidic environment also limits the application of AM parts in water splitting for hydrogen production. Here, bipolar plates (BPs), which are used to transport reactants/products and conduct electrons in proton exchange membrane electrolyzer cells (PEMECs), are printed from stainless steel (SS) with selective laser melting (SLM). Then surface treatments are employed on those BPs by thin film electroplating with Au, and the protective thin layer enables the utilization of AM SS parts to both cathode and anode sides of water electrolyzer cells and exhibits superior corrosion resistances and electronic conductivities. The Au-coated AM SS BPs deliver a low interfacial contact resistance (6.4 mO cm 2 under 1.45 MPa) and an excellent performance in PEMECs (1.71 V at 2 A/cm 2 ), and maintain a remarkable durability in the simulated anode environment compared with the uncoated AM SS BPs and conventional graphite BPs. In conclusion, this approach demonstrates the possibility of 3-dimensional printing fully integrated water electrolyzer cells at both anode and cathode sides.

08 HYDROGEN↗

Laser ablation for structuring Li-ion electrodes for fast charging and its impact on material properties, rate capability, Li plating, and wetting

Laser ablation is a scalable technique for decreasing the effective tortuosity of electrodes by selectively removing material with high precision. Applied to ≈ 110 um thick electrode coatings, this work focuses on understanding the impact of laser ablation on electrode material properties at the beginning of life and synergistic impacts of ablated channels on cell performance throughout their cycle life. Post laser ablation, local changes in chemistry, crystallography, and morphology of the laser-impacted electrode regions are investigated. It is shown that femtosecond pulsed laser ablation can achieve high-rate material removal with minor material damage locally at the interface of the impacted zones. The capacity achieved during a 6C (10 min) constant-current constant-voltage charge to 4.2 V improved from 1 mAh cm -2 for the non-ablated electrodes to almost 2 mAh cm -2 for the ablated electrodes. This benefit is attributed to a synergistic effect of enhanced wetting and decreased electrode tortuosity. The benefit was maintained for over 120 cycles, and upon disassembly decreased Li-plating on the graphite anode was observed. Finally, multi-physics modeling in conjunction with wetting analyses showed that laser ablating either one of the electrodes led to substantial improvements in wetting and rate capability, indicating that substantial performance benefits can be achieved by ablating only the graphite anode as apposed to both electrodes.

25 ENERGY STORAGE↗

Effect of heat input on the microstructure and mechanical properties of tungsten inert gas arc butt-welded AZ61 magnesium alloy plates

In this paper, the effects of heat input on the microstructures and mechanical properties of tungsten inert gas arc butt-welded AZ61 magnesium alloy plates were investigated by microstructural observations, microhardness tests and tensile tests. The results show that with an increase of the heat input, the grains both in the fusion zone and the heat-affected zone coarsen and the width of the heat-affected zone increased. Moreover, an increase of the heat input resulted in a decrease of the continuous {beta}-Mg{sub 17}Al{sub 12} phase and an increase of the granular {beta}-Mg{sub 17}Al{sub 12} phase in both the fusion zone and the heat-affected zone. The ultimate tensile strength of the welded joint increased with an increase of the heat input, while, too high a heat input resulted in a decrease of the ultimate tensile strength of the welded joint. In addition, the average microhardness of the heat-affected zone and fusion zone decreased sharply with an increase of the heat input and then decreased slowly at a relatively high heat input.

36 MATERIALS SCIENCE↗

Flow of a binary mixture of linearly incompressible viscous fluids between two horizontal parallel plates

In this paper, we use the classical Mixture Theory and present exact solutions to the equations of motion for the steady flow of two linearly viscous fluids between two horizontal plates. We show that for a saturated mixture and under very special conditions, namely when the body forces are assumed negligible, the only interaction force is due to relative velocity (drag force), and if the two velocities are assumed to be related to each other in a linear fashion, then it is possible to integrate the coupled ordinary differential equations and obtain analytical expressions for the velocities and the volume fraction.

42 ENGINEERING↗

Direct tests of micro channel plates as the active element of a new shower maximum detector

We continue the study of micro channel plates (MCP) as the active element of a shower maximum (SM) detector. We present below test beam results obtained with MCPs detecting directly secondary particles of an electromagnetic shower. The MCP efficiency to shower particles is close to 100%. Furthermore, the time resolution obtained for this new type of the SM detector is at the level of 40 ps.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Using pulse shape analysis to improve the position resolution of a resistive anode microchannel plate detector

Digital signal processing techniques were employed to investigate the joint use of charge division and risetime analyses for the resistive anode (RA) coupled to a microchannel plate detector (MCP). In contrast to the typical approach of using the relative charge at each corner of the RA, this joint approach results in a significantly improved position resolution. A conventional charge division analysis utilizing analog signal processing provides a measured position resolution of 170 μm (FWHM). By using the correlation between risetime and position we were able to obtain a measured resolution of 92μm (FWHM), corresponding to an intrinsic resolution of 64μm (FWHM) for a single Z-stack MCP detector.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Direct tests of a pixelated microchannel plate as the active element of a shower maximum detector

One possibility to make a fast and radiation resistant shower maximum detector is to use a secondary emitter as an active element. We report our studies of microchannel plate photomultipliers (MCPs) as the active element of a shower-maximum detector. We present test beam results obtained using Photonis XP85011 to detect secondary particles of an electromagnetic shower. We focus on the use of the multiple pixels on the Photonis MCP in order to find a transverse two-dimensional shower distribution. A spatial resolution of 0.8 mm was obtained with an 8 GeV electron beam. As a result, a method for measuring the arrival time resolution for electromagnetic showers is presented, and we show that time resolution better than 40 ps can be achieved.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Performance studies of atomic layer deposited microchannel plate electron multipliers

Microchannel plate (MCP) photon counting, event timing, imaging detectors have found wide use in astronomical, remote sensing, and biological imaging applications. Novel MCP technology using borosilicate glass microcapillary array substrates functionalized by the application of resistive and secondary emissive layers using atomic layer deposition (ALD) techniques has the potential to outperform traditional MCP technology. Using ALD techniques to functionalize the MCPs allow customization of parameters like gain and resistance independently from the glass substrate. Borosilicate substrates have many advantages over traditional micro-capillary arrays, including low radioactive content, higher open area ratios, low outgassing, and high operational stability. These ALD MCPs can be manufactured in large areas (400 cm 2 ) providing a unique solution for many timing/imaging applications. ALD MCPs can withstand the processing temperatures required for high temperature deposition of III-V materials, such as Gallium Nitride, for UV photocathodes with high quantum efficiencies (QE) in the Near-UV (similar to 100-380 nm). We present the effects of different ALD configurations on the gain (magnitude and uniformity), resistance, imaging, background and detection efficiency, and how these parameters change during lifetime testing. Here, we also present the QE of ALD MCPs and various QE enhancement techniques.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Rate-induced aging effects on Parallel-Plate Avalanche Counter (PPAC) caused by heavy ion beams

The Facility for Rare Isotope Beams (FRIB) is one of the premier scientific user facilities for nuclear science with radioactive beams, capable of producing most (approximately 80%) of the isotopes expected to exist, from oxygen to uranium, at energies up to 200 MeV/u. With the increase in beam power from the present 10 kW to the planned 400 kW, FRIB experiments are about to enter a new era. An unprecedented rate capability as well as stable performance of all the planned instrumentation intended for beam diagnostics and beam tuning is required at the expected high beam intensities (> 1 MHz). A summary of aging phenomena at high heavy-ion beam rates observed in the Advanced Rare Isotope Separator (ARIS) detectors for beam diagnostics, including Parallel Plate Avalanche Counters (PPAC) and plastic scintillation for time-of-flight measurements, is discussed. Current research and development project to mitigate rate-induced aging are presented.

Aging effects↗

Investigation of the flow field inside flat-plate collector tube using PIV technique

The thermofluid process inside the tube of flat-plate collectors is complex because the non-uniform heating of the tube results in the formation of stably and unstably stratified layers of fluid that interact with each other. The measurement and investigation of the flow behaviour inside the collector tube is very challenging. We report on a novel application of the particle image velocimetry (PIV) technique to remotely measure the velocity field inside the collector tube. The two-dimensional velocity fields were measured in the midplane of a collector tube for the Reynolds number range of 150-900 at unheated and four different heating conditions. We have presented and discussed in detail the technique implementation and the associated challenges. The results have shown that the collector heating significantly alters the structure and magnitude of the mean velocity field and influences the heat transfer to the fluid. It is observed that the collector heating causes a significant asymmetry in the mean velocity profiles over the given range of Reynolds numbers and heating conditions. (author)

14 SOLAR ENERGY↗

Electrical Conductivity and Sound Velocities of Talc Under High Pressure and High Temperature Conditions and Application to the Subducting Cocos Plate

Talc is expected to be an important water carrier in Earth's upper mantle, and understanding its electrical and seismic properties under high pressure and temperature conditions is required to detect possible talc-rich regions in subduction zones imaged using geophysical observations. Here, we conducted acoustic and electrical experiments on natural talc aggregates at relevant pressure-temperature conditions. Compressional wave velocity (V p ) was measured using ultrasonic interferometry in a Paris-Edinburgh press at pressures up to 3.4 GPa and temperatures up to 873 K. Similar Vp values are obtained regardless of the initial crystallographic preferred orientation of the samples, which can be explained by talc grain reorientation during the experiment, with the (001) plane becoming perpendicular to the uniaxial compression axis. Electrical conductivity of the same starting material was determined using impedance spectroscopy in a multi-anvil press up to 6 GPa and 1263 K. Two conductivity jumps are observed, at ∼860–1025 K and ∼940–1080 K, depending on pressure, and interpreted as talc dehydroxylation and decomposition, respectively. Electrical anisotropy is observed at low temperature and decreases with increasing pressure (∼10 at 1.5 GPa and ∼2 at 3.5 GPa). Comparison of acoustic and electrical results with geophysical observations in central Mexico supports the presence of a talc-bearing layer atop the subducted Cocos plate.

Cocos plate↗

Using a short-pulse diffraction-limited laser beam to probe filamentation of a random phase plate smoothed beam

A short pulse (few picoseconds) laser probe provides high temporal resolution measurements to elucidate details of fast dynamic phenomena not observable with typical longer laser pulse probes and gated diagnostics. Such a short pulse laser probe (SPLP) has been used to measure filamentation of a random phase plate (RPP) smoothed laser beam in a gas-jet plasma. The plasma index of refraction due to driven density and temperature fluctuations by the RPP beam perturbs the phase front of a SPLP propagating at a 90 deg. angle with respect to the RPP interaction beam. The density and temperature fluctuations are quasistatic on the time scale of the SPLP ({approx}2 ps). The transmitted near-field intensity distribution from the SPLP provides a measure of the phase front perturbation. At low plasma densities, the transmitted intensity pattern is asymmetric with striations across the entire probe beam in the direction of the RPP smoothed beam. As the plasma density increases, the striations break up into smaller sizes along the direction of the RPP beam propagation. The breakup of the intensity pattern is consistent with self-focusing of the RPP smoothed interaction beam. Simulations of the experiment using the wave propagation code, PF3D, are in qualitative agreement demonstrating that the asymmetric striations can be attributed to the RPP driven density fluctuations. Quantification of the beam breakup measured by the transmitted SPLP could lead to a new method for measuring self-focusing of lasers in underdense plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Refine your search to explore more results.