Search NASA⌕ Search

SEARCH · Search NASA

Results for “Vibration Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

Bellows flow-induced vibrations

The bellows flow excitation mechanism and results of comprehensive test program are summarized. The analytical model for predicting bellows flow induced stress is refined. The model includes the effects of an upstream elbow, arbitrary geometry, and multiple piles. A refined computer code for predicting flow induced stress is described which allows life prediction if a material S-N diagram is available.

Tygielski, P. J.↗

Response measurements for two building structures excited by noise from a large horizontal axis wind turbine generator

Window and wall acceleration measurements and interior noise measurements ere made for two different building structures during excitation by noise from the WTS-4 horizontal axis wind turbine generator operating in a normal power generation mode. With turbine noise input pulses resulted in acceleration pulses for the wall and window elements of the two tests buildings. Response spectra suggest that natural vibration modes of the structures are excited. Responses of a house trailer were substantially greater than those for a building of sturdier construction. Peak acceleration values correlate well with similar data for houses excited by flyover noise from commercial and military airplanes and helicopters, and sonic booms from supersonic aircraft. Interior noise spectra have peaks at frequencies corresponding to structural vibration modes and room standing waves; and the levels for particular frequencies and locations can be higher than the outside levels.

Hubbard, H. H.↗

DC-10 winglet flight evaluation

The results of a flight evaluation of winglets on a DC-10 Series 10 aircraft are presented. For sensitive areas of comparison, effects of winglets were determined back to back with and without winglets. Basic and reduced span winglet configurations were tested. After initial encounter with low speed buffet, a number of acceptable configurations were developed. For maximum drag reduction at both cruise and low speeds, lower winglets were required, having leading edge devices on upper and lower winglets for the latter regime. The cruise benefits were enhanced by adding outboard aileron droop to the reduced span winglet aircraft. Winglets had no significant impact on stall speeds, high speed buffet boundary, and stability and control characteristics. Flutter test results agreed with predictions and ground vibration data. Flight loads measurement also agreed with predictions.

Source record↗

Six degree-of-freedom LIVE isolation systems, part 1

A Total Main Rotor Isolation System (TRIS) was analyzed, designed, fabricated, and bench tested for the reduction of main rotor vibration levels transmitted to the helicopter fuselage. The TRIS consists of a six degree-of-freedom passive system using six Liquid Inertia Vibration Eliminator (LIVE) units developed by Bell Helicopter Textron. The objective of the program is to develop a helicopter isolation system that will achieve 90% (or greater) isolation at minimum weight with no degradation in vehicle stability, handling qualities, alignment tolerance, and reliability or maintainability.

Halwes, D. R.↗

Structureborne noise in aircraft: Modal tests

As part of an investigation to develop measurement techniques for structureborne noise, three modal surveys have been conducted on an OV-10A aircraft and the results have been presented. The purpose of the modal surveys was to identify suitable locations for mounting accelerometer and strain gages in subsequent tests in which transfer functions relating wing vibration to interior noise were to be determined. These surveys are as follows:(1) wing/fuselage modal survey utilizing one shaker under the right wing; (2) complete wing modal survey utilizing two shakers, one under each wing; and (3) fuselage side panel modal survey utilizing a small instrumented hammer. The predominant frequencies and damping ratios for each analysis were listed in tables. The primary mode shapes at the lower frequencies and at frequencies near the expected engine driving frequencies have been shown for each survey.

Clevenson, S. A.↗

COFS 3: Multibody dynamics and control technology

COFS 3 is the third project within the Control of Flexible Structures (COFS) program. It deals with developing multibody dynamics and control technology for large space structures. It differs from COFS 1 and 2 in two respects. First, it addresses a more complex class of structure, and second it is basically a scale model ground test and analysis program while COFS 1 and 2 feature Shuttle flight experiments. The specific technology thrusts within COFS 3 are model sensitivities, test methods, analysis validation, systems identification, and vibration suppression. The COFS 3 project will develop the methods for using dynamically scaled models and analysis to predict the structural dynamics of large space structures. The project uses the space station as a focus because it is typical of the structures of interest and provides the first opportunity to obtain full-scale on-orbit dynamics data.

Letchworth, Robert↗

DC-10 winglet flight evaluation

Results of a flight evaluation of winglets on a DC-10 Series 10 aircraft are presented. For sensitive areas of comparison, effects of winglets were determined back-to-back with and without winglets. Basic and reduced-span winglet configurations were tested. After initial encounter with low-speed buffet, a number of acceptable configurations were developed. For maximum drag reduction at both cruise and low speeds, lower winglets were required, having leading edge devices on upper and lower winglets for the latter regime. The cruise benefits were enhanced by adding outboard aileron droop to the reduced-span winglet aircraft. Winglets had no significant impact on stall speeds, high-speed buffet boundary, and stability and control. Flutter test results agreed with predictions and ground vibration data. Flight loads measurement, provided in a concurrent program, also agreed with predictions. It was estimated that a production version of the aircraft, using the reduced-span winglet and aileron droop, would yield a 3-percent reduction in fuel burned with capacity payload. This range was 2% greater than with winglets. A 5% reduction in takeoff distance at maximum takeoff weight would also result.

Taylor, A. B.↗

Workshop on Structural Dynamics and Control Interaction of Flexible Structures

The Hubble Space Telescope features the most exacting line of sight jitter requirement thus far imposed on a spacecraft pointing system. Consideration of the fine pointing requirements prompted an attempt to isolate the telescope from the low level vibration disturbances generated by the attitude control system reaction wheels. The primary goal was to provide isolation from axial component of wheel disturbance without compromising the control system bandwidth. A passive isolation system employing metal springs in parallel with viscous fluid dampers was designed, fabricated, and space qualified. Stiffness and damping characteristics are deterministic, controlled independently, and were demonstrated to remain constant over at least five orders of input disturbance magnitude. The damping remained purely viscous even at the data collection threshold of .16 x .000001 in input displacement, a level much lower than the anticipated Hubble Space Telescope disturbance amplitude. Vibration attenuation goals were obtained and ground test of the vehicle has demonstrated the isolators are transparent to the attitude control system.

Davis, L. P.↗

Recent trends in rotary-wing aeroelasticity

The purpose of this paper is to survey the principal developments which have occurred in the field of rotary-wing aeroelasticity during the past five-year period. This period has been one of considerable activity and approximately one hundred papers have been published on this topic. To facilitate this review the field has been divided into a number of areas in which concentrated research activity has taken place. The main areas in which recent research is reviewed are: (1) structural modeling; (2) aerodynamic modeling; (3) aeroelastic problem formulation using automated or computerized methods; (4) aeroelastic analyses in forward flight; (5) coupled rotor/fuselage analyses; (6) active controls and their application to aeroelastic response and stability; (7) application of structural optimization to vibration response; and (8) aeroelastic analysis and testing of special configurations. These areas are reviewed with different levels of detail and some useful observations regarding potentially rewarding areas of future research are made.

Friedmann, Peretz P.↗

Recent trends in rotary-wing aeroelasticity

The purpose of this paper is to survey the principal developments which have occurred in the field of rotary-wing aeroelasticity during the past five year period. This period has been one of considerable activity and approximately one hundred papers have been published on this topic. To facilitate this review the field has been divided into a number of areas in which concentrated research activity has taken place. The main areas in which recent research is reviewed are: (1) structural modeling; (2) aerodynamic modeling; (3) aeroelastic problem formulation using automated or computerized methods; (4) aeroelastic analyses in forward flight; (5) coupled rotor/fuselage analyses; (6) active controls and their application to aeroelastic response and stability; (7) application of structural optimization to vibration reduction; and (8) aeroelastic analysis and testing of special configurations. These areas are reviewed with different levels of detail and some useful observations regarding potentially rewarding areas of future research are made.

Friedmann, Peretz P.↗

Technique for temperature compensation of eddy-current proximity probes

Eddy-current proximity probes are used in turbomachinery evaluation testing and operation to measure distances, primarily vibration, deflection, or displacment of shafts, bearings and seals. Measurements of steady-state conditions made with standard eddy-current proximity probes are susceptible to error caused by temperature variations during normal operation of the component under investigation. Errors resulting from temperature effects for the specific probes used in this study were approximately 1.016 x 10 to the -3 mm/deg C over the temperature range of -252 to 100 C. This report examines temperature caused changes on the eddy-current proximity probe measurement system, establishes their origin, and discusses what may be done to minimize their effect on the output signal. In addition, recommendations are made for the installation and operation of the electronic components associated with an eddy-current proximity probe. Several techniques are described that provide active on-line error compensation for over 95 percent of the temperature effects.

Masters, Robert M.↗

Doppler-Shifted Raman Spectroscopy Measures Flows

Technique for measuring velocity, static pressure, and translational temperature of flowing molecules by use of stimulated Raman spectroscopy demonstrated in supersonic wind tunnel at NASA Langley Research Center. Nonintrusive, accurate wind-tunnel measurements obtained without seeding flows. Optical equipment for vibration-free Raman doppler velocimetry in wind tunnel includes specially designed retrometer that reduces sensitivity of system to vibrations. This capability very valuable in aerodynamic testing and proves useful in wide variety of laboratory, industrial, and engineering applications.

Exton, Reginald J.↗

On the development of the power sources for the Ulysses and Galileo missions

The technically challenging European Space Agency Ulysses mission to explore the polar regions of the Sun and the NASA Galileo mission to explore Jupiter have prompted the development of the most powerful radioisotope thermoelectric generator (RTG) yet built for space use. This RTG, which was designed to provide a minimum of 285 We at beginning of mission builds upon the successful thermoelectric technology developed for the RTGs now in operation on the Voyager 1 and 2 spacecraft. A total of four flight RTGs, one ground qualification RTG, and one Engineering Unit have been built and tested for the Galileo and Ulysses missions. The tests have included measurements of functional performance, vibration response, magnetic signature, mass properties, nuclear radiation, and vacuum performance. The RTGs are fully flight qualified for both missions and are ready for launch.

Gary L. Bennett↗

Shuttle Entry Air Data System (SEADS) hardware development. Volume 1: Summary

Hardware development of the Shuttle Entry Data System (SEADS) is described. The system consists of an array of fourteen pressure ports, installed in an Orbiter nose cap, which, when coupled with existing fuselage mounted static pressure ports permits computation of entry flight parameters. Elements of the system that are described include the following: (1) penetration assemblies to place pressure port openings at the surface of the nose cap; (2) pressure tubes to transmit the surface pressure to transducers; (3) support posts or manifolds to provide support for, and reduce the length of, the individual pressure tubes; (4) insulation for the manifolds; and (5) a SEADS nose cap. Design, analyses, and tests to develop and certify design for flight are described. Specific tests include plasma arc exposure, radiant thermal, vibration, and structural. Volume one summarizes highlights of the program, particularly as they relate to the final design of SEADS. Volume two summarizes all of the Vought responsible activities in essentially a chronological order.

While, D. M.↗

Shuttle Entry Air Data System (SEADS) hardware development. Volume 2: History

Hardware development of the Shuttle Entry Air Data System (SEADS) is described. The system consists of an array of fourteen pressure ports, installed in an Orbiter nose cap, which, when coupled with existing fuselage mounted static pressure ports permits computation of entry flight parameters. Elements of the system that are described include the following: (1) penetration assemblies to place pressure port openings at the surface of the nose cap; (2) pressure tubes to transmit the surface pressure to transducers; (3) support posts or manifolds to provide support for, and reduce the length of, the individual pressure tubes; (4) insulation for the manifolds; and (5) a SEADS nose cap. Design, analyses, and tests to develop and certify design for flight are described. Specific tests included plasma arc exposure, radiant thermal, vibration, and structural. Volume one summarizes highlights of the program, particularly as they relate to the final design of SEADS. Volume two summarizes all of the Vought responsible activities in essentially a chronological order.

While, D. M.↗

CETA truck and EVA restraint system

The Crew Equipment Translation Aid (CETA) experiment is an extravehicular activity (EVA) Space Transportation System (STS) based flight experiment which will explore various modes of transporting astronauts and light equipment for Space Station Freedom (SSF). The basic elements of CETA are: (1) two 25 foot long sections of monorail, which will be EVA assembled in the STS cargo bay to become a single 50 ft. rail called the track; (2) a wheeled baseplate called the truck which rolls along the track and can accept three cart concepts; and (3) the three carts which are designated manual, electric, and mechanical. The three carts serve as the astronaut restraint and locomotive interfaces with the track. The manual cart is powered by the astronaut grasping the track's handrail and pulling himself along. The electric cart is operated by an astronaut turning a generator which powers the electric motor and drives the cart. The mechanical cart is driven by a Bendix type transmission and is similar in concept to a man-propelled railroad cart. During launch and landing, the truck is attached to the deployable track by means of EVA removable restraint bolts and held in position by a system of retractable shims. These shims are positioned on the exterior of the rail for launch and landing and rotate out of the way for the duration of the experiment. The shims are held in position by strips of Velcro nap, which rub against the sides of the shim and exert a tailored force. The amount of force required to rotate the shims was a major EVA concern, along with operational repeatability and extreme temperature effects. The restraint system was tested in a thermal-vac and vibration environment and was shown to meet all of the initial design requirements. Using design inputs from the astronauts who will perform the EVA, CETA evolved through an iterative design process and represented a cooperative effort.

Beals, David C.↗

Blade-Mounted Flap Control for BVI Noise Reduction Proof-of-Concept Test

This report describes a wind tunnel test of the McDonnell Douglas Helicopter Systems (MDHS) Active Flap Model Rotor at the NASA Langley 14- by 22-Foot Subsonic Tunnel. The test demonstrated that BVI noise reductions and vibration reductions were possible with the use of an active flap. Aerodynamic results supported the acoustic data trends, showing a reduction in the strength of the tip vortex with the deflection of the flap. Acoustic results showed that the flap deployment, depending on the peak deflection angle and azimuthal shift in its deployment schedule, can produce BVI noise reductions as much as 6 dB on the advancing and retreating sides. The noise reduction was accompanied by an increase in low frequency harmonic noise and high frequency broadband noise. A brief assessment of the effect of the flap on vibration showed that significant reductions were possible. The greatest vibration reductions (as much as 76%) were found in the four per rev pitching moment at the hub. Performance improvement cam results were inconclusive, as the improvements were predicted to be smaller than the resolution of the rotor balance.

Dawson, Seth↗

Integrating Oil Debris and Vibration Gear Damage Detection Technologies Using Fuzzy Logic

A diagnostic tool for detecting damage to spur gears was developed. Two different measurement technologies, wear debris analysis and vibration, were integrated into a health monitoring system for detecting surface fatigue pitting damage on gears. This integrated system showed improved detection and decision-making capabilities as compared to using individual measurement technologies. This diagnostic tool was developed and evaluated experimentally by collecting vibration and oil debris data from fatigue tests performed in the NASA Glenn Spur Gear Fatigue Test Rig. Experimental data were collected during experiments performed in this test rig with and without pitting. Results show combining the two measurement technologies improves the detection of pitting damage on spur gears.

Dempsey, Paula J.↗

Refine your search to explore more results.