Search NASA⌕ Search

SEARCH · Search NASA

Results for “WINGS - SWEEPBACK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

The effect of canard and vertical tails on the aerodynamic characteristics of a model with a 59 deg sweptback wing at a Mach number of 0.30

An investigation has been conducted to determine the effects of canard, canard location, vertical tails, and vertical-tail location on the aerodynamic characteristics of a model having a 59 deg sweptback wing. The investigation was conducted at a Mach number of 0.30, at angles of attack up to 22 deg and at sideslip angles of 0 deg and plus or minus 5 deg. The results of the study indicate that adding the canard to the model had only a slight effect on the lift at the lower angles of attack. At the higher angles of attack there is a significant effect of canard height on lift, canard in the high location (above the wing chord plane) resulting in the highest lifts. The lift drag characteristics are predicted well for the configuration with the mid or high canard locations by combining a potential flow solution on the canard with a potential plus vortex solution on the wing. Variations in the height significantly affect the pitching-moment characteristics of the configuration; the configuration with the low or mid canard location exhibits an increase in stability at the higher lift coefficients, whereas the configuration with the high canard exhibits pitch-up. Adding the vertical tails in the outboard location caused a significant loss in lift at the higher angles of attack; this lift loss was eliminated by moving the vertical tails inboard.

Henderson, W. P.↗

Extension of leading-edge-suction analogy to wings with separated flow around the side edges at subsonic speeds

A method for determining the lift, drag, and pitching moment for wings which have separated flow at the leading and side edges with subsequently reattached flow downstream and inboard is presented. Limiting values of the contribution to lift of the side-edge reattached flow are determined for rectangular wings. The general behavior of this contribution is computed for rectangular, cropped-delta, cropped-diamond, and cropped-arrow wings. Comparisons of the results of the method and experiment indicate reasonably good correlation of the lift, drag, and pitching moment for a wide planform range. The agreement of the method with experiment was as good as, or better than, that obtained by other methods. The procedure is computerized and is available from COSMIC as NASA Langley computer program A0313.

Lamar, J. E.↗

Transonic flow about lifting wing-body combinations

Calculations for transonic flow about wing-body combinations at angles of attack of the order of the body thickness-to-length ratio are presented. These calculations show that lift can alter the flow drastically at near-sonic speeds in this angle-of-attack range so that the area rule must be modified. This effect of lift is explained from simple physical considerations. The computational procedure is based on slender-wing theory and a two-variable method of relaxation solution. A small perturbation analysis is used to show that this simple procedure is adequate for these transonic wing-body flow fields.

Barnwell, R. W.↗

Optimal aeroelastic design of an oblique wing structure

A procedure is presented for determining the optimal cover panel thickness of a wing structure to meet specified strength and static aeroelastic divergence requirements for minimum weight. Efficient reanalysis techniques using discrete structural and aerodynamic methods are used in conjunction with redesign algorithms driven by optimality criteria. The optimality conditions for the divergence constraint are established, and expressions are obtained for derivatives of the dynamic pressure at divergence with respect to design variables. The procedure is applied to an oblique wing aircraft where strength and stiffness are critical design considerations for sizing the cover thickness of the wing structure.

Gwin, L. B.↗

Geometry considerations for jet noise shielding with CTOL engine-over-the-wing concept

Jet noise shielding benefits for CTOL engine-over-the-wing installations were obtained with various model-scale circular nozzles and wing chord geometries. Chord-to-nozzle diameter ratios were varied from 3 to 20, while ratios of nozzle height above the wing to the diameter were varied from near zero to 3. Spectral noise data were obtained with jet velocities from 640 to 1110 ft/sec. Characteristics of low frequency noise sources are discussed. Jet-noise shielding is correlated in terms of acoustic and geometric parameters. Implications of extending the model-scale data to full-scale are discussed.

Von Glahn, U.↗

High attitude delta wing unsteady aerodynamics

An analysis of the steady and unsteady aerodynamics of sharp-edged slender wings has been performed. The results show that slender wing theory can be modified to give the potential flow static and dynamic characteristics in incompressible flow. A semiempirical approximation is developed for the vortex-induced loads, and it is shown that the analytic approximation for sharp-edged slender wings gives good prediction of experimentally determined steady and unsteady aerodynamics. The results indicate that the effects of delta planform lifting surfaces can be included in a simple manner when determining the aeroelastic characteristics of the space shuttle lift-off configuration.

Ericsson, L. E.↗

A quasi-vortex-lattice method in thin wing theory

A quasi-continuous method is developed for solving thin-wing problems. For the purpose of satisfying the wing boundary conditions, the spanwise vortex distribution is assumed to be stepwise-constant, while the chordwise vortex integral is reduced to a finite sum through a modified trapezoidal rule and the theory of Chebyshev polynomials. Wing-edge and Cauchy singularities are acounted for. The total aerodynamic characteristics are obtained by an appropriate quadrature integration. The two-dimensional results for airfoils without flap deflection reproduce the exact solutions in lift and pitching moment coefficients, the leading edge suction, and the pressure difference at a finite number of points. For a flapped airfoil, the present results are more accurate than those given by the vortex-lattice method. The three-dimensional results also show an improvement over the results of the vortex-lattice method. Extension to nonplanar applications is discussed.

Lan, C. E.↗

Effects of leading edge sweep angle and design lift coefficient on performance of a modified arrow wing at a design Mach number of 2.6

Wing models were tested in the high-speed section of the Langley Unitary Plan wind tunnel to study the effects of the leading-edge sweep angle and the design lift coefficient on aerodynamic performance and efficiency. The models had leading-edge sweep angles of 69.44 deg, 72.65 deg, and 75.96 deg which correspond to values of the design Mach-number-sweep-angle parameter (beta cotangent A) sub DES of 0.6, 0.75, and 0.9, respectively. For each sweep angle, camber surfaces having design lift coefficients of 0,0.08, and 0.12 at a design Mach number of 2.6 were generated. The wind-tunnel tests were conducted at Mach numbers of 2.3, 2.6, and 2.96 with a stagnation temperature of 338.7 K (150 F) and a Reynolds number per meter of 9.843 times 10 to the 6th power. The results of the tests showed that only a moderate sweeping of the wing leading edge aft of the Mach line along with a small-to-moderate amount of camber and twist was needed to significantly improve the zero-lift (flat camber surface) wing performance and efficiency.

Mack, R. J.↗

Effects of the air breathing engine plumes on SSV orbiter subsonic wing pressure distributions (OA57A)

Experimental aerodynamic pressure investigations were conducted on a 0.0405 scale representation of the -89 space shuttle orbiter ferry configuration in the Rockwell International 7.75 x 11.00 foot Low Speed Wind Tunnel. The primary test objective was to investigate the orbiter wing pressure distribution resulting from five under-wing engine nacelle plumes. Two five engine nacelle configurations were tested at 3 ground plane heights with pressure bug measurements being made on the left upper and lower wing panel. In addition, base and balance cavity pressure measurements were made, with elevon normal and hinge moment measurements on the right panel.

Cameron, B. W., Jr.↗

Calculation of the twist distribution of wings designed for cruise at transonic speeds

The use of linear theory in calculating the twist distribution of a wing designed for cruise at supercritical speeds is justified on the basis of the transonic equivalence rule. A modified version of Multhopp's subsonic lifting-surface theory was used to calculate the twist distribution. The lifting-surface theory is compared with both slender wing theory and experimental results. A study was also made of the effect of wing sweep on the twist distribution required to maintain an elliptic span load at cruise conditions. The important parameters used in establishing this twist distribution are identified.

Mann, M. J.↗

Subsonic roll-damping characteristics of a series of wings

The aerodynamic damping in roll of a series of wings has been investigated in the Langley high-speed 7- by 10-foot tunnel at Mach numbers ranging from 0.2 to 0.8 by use of a forced oscillatory-roll technique. Tests were conducted on wings of aspect ratio 6 with sweep angles of 25, 35, and 45 deg and on 35 deg swept wings of aspect ratios 4 and 5.

Boyden, R. P.↗

Wind tunnel investigation of a twin engine straight wing upper surface blown jet flap configuration

An investigation was conducted in a full scale wind tunnel to determine the performance and aerodynamic characteristics of a twin engine, straight wing, upper surface blown jet flap configuration. The model had two simulated high bypass ratio turbofan engines with rectangular nozzles exhausting onto the upper surface of the wing at the 35 percent chord station. The model was tested with an aspect ratio 8.2 wing and with the wingtips removed to give an aspect ratio of 6.0.

Phelps, A. E., III↗

Analytical and experimental study of the effects of wing-body aerodynamic interaction on space shuttle subsonic flutter

The effects on flutter of the aerodynamic interaction between the space shuttle bodies and wing, 1/80th-scale semispan models of the orbiter wing, the complete shuttle and intermediate component combinations were tested in the NASA Langley Research Center 26-inch Transonic Blowdown Wind Tunnel. Using the double lattice method combined with slender body theory to calculate unsteady aerodynamic forces, subsonic flutter speeds were computed for comparison. Using calculated complete vehicle modes, flutter speed trends were computed for the full scale vehicle at an altitude of 15,200 meters and a Mach number of 0.6. Consistent with findings of the model studies, analysis shows the shuttle to have the same flutter speed as an isolated cantilevered wing.

Chipman, R. R.↗

Low-speed wind-tunnel investigation of forward-located spoilers and trailing splines as trailing-vortex hazard-alleviation devices on an aspect-ratio-8 wing model

An investigation was made in the Langley V/STOL tunnel in order to determine, by the trailing-wing sensor technique, the effectiveness of either a forward-mounted spoiler or a tip-mounted spline as trailing-vortex attenuation devices on an unswept aspect-ratio-8 wing model. The trailing-wing rolling-moment data taken in the tunnel diffuser section show good agreement with the data taken in the tunnel test section. This agreement indicates that reasonable results may be obtained in the Langley V/STOL tunnel in experimental investigations of the trailing-vortex hazard at relatively great distances behind aircraft models.

Croom, D. R.↗

Velocity and rolling-moment measurements in the wake of a swept-wing model in the 40 by 80 foot wind tunnel

Measurements were made in the wake of a swept wing model to study the structure of lift generated vortex wakes shed by conventional span loadings and by several span loadings designed to reduce wake velocities. Variations in the span loading on the swept wing generator were obtained by deflecting seven flap segments on each side by amounts determined by vortex lattice theory to approximate the desired span loadings. The resulting wakes were probed with a three component, hot wire probe to measure velocity, and with a wing to measure the rolling moment that would be induced on a following aircraft. The experimental techniques are described herein, and the measured velocity and rolling moments are presented, along with some comparisons with the applicable theories.

Rossow, V. J.↗

The simulation of turbulent boundary layer separation on multi-element infinite swept wings

An improved method of simulating the effect of flow separation on potential flow over two-dimensional and infinite swept multi-element wings was developed. Two types of flow separation are considered: at the wing trailing edge, and at the cove region between the main wing and the flap. Potential flow is assumed outside the boundary layer and the separated wake. A previously obtained computer program (VIP) is modified by matching the outflow distribution for the potential flow such that the potential flow part of the real flow is duplicated and the results agree with the experimental observations. Results are given for the NACA 2412 airfoil. Iterative drag calculations are presented.

Dvorak, F. A.↗

Nonlinearities in analyses of unsteady flow around oscillating wings

An analysis of nonlinearities involved in unsteady subsonic viscous flow around wings at high Reynolds numbers is presented. The finite element method was applied for the numerical integration of the vorticity transport equations. Physical and numerical aspects of the nonlinearities are discussed. Magnification of nonlinearities in the convection terms near wing surfaces due to changing geometry at leading and trailing edges of the wing chord is determined. As a bubble is generated near the leading edge, the timewise variation of vorticity and pressure distributions over the surface is shown. The different procedures for the integration of the vorticity transport equations in three dimensions along spanwise, chordwise, and normal directions are discussed.

Bratanow, T.↗

Hypersonic wing test structure design, analysis, and fabrication

An investigation was conducted to provide the analyses, data, and hardware required to experimentally validate the beaded panel concept and demonstrate its usefulness as a basis for design of a hypersonic research airplane (HRA). Combinations of beaded panel structure, heat shields, channel caps, and corrugated webs for ribs and spars were analyzed for the wing of a specified HRA to operate at Mach 8 with a life span of 150 flights. Detailed analyses, conducted in accordance with established design criteria, included aerodynamic heating and load predictions, transient structural thermal calculations, extensive NASTRAN computer modeling, and structural optimization. After geometry was established for the total wing, part of the wing (85 sq ft) was designed, fabricated, and assembled into a test structure to experimentally verify the structural adequacy of the beaded panel design concept.

Plank, P. P.↗

Refine your search to explore more results.