Search NASA⌕ Search

SEARCH · Search NASA

Results for “defect microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

The change of electrical transport characterizations in Ga doped ZnO films with various thicknesses

GZO films with different thicknesses were prepared at room temperature by magnetron sputtering and the structure is characterized using two-dimensional X-ray diffraction along with transmission electron microscope and X-ray photoelectron spectroscopy. The films show a textured orientation along the c-axis and an average transmittance of over 90%. The films of 100 and 200 nm are characterized by a semiconductor behavior in the temperature range of 80-320 K, while the conduction behavior turns into a metallic transport at 160 K as the film thickness increases to 400 nm. Temperature dependence of the conductivity manifests a weak localization effect dominated in the semiconductor behavior. The transition between semiconductor and metallic behavior with increasing the thickness is shown to be associated to crystallinity of the films which is improved with decreasing defects and lattice distortion. It is suggested that the improvement of crystallinity should be favored by reduction of the weak localization effect and in turn enhance the semiconductor-to-metal transition.

36 MATERIALS SCIENCE↗

Nanoscale selective area growth of thick, dense, uniform, In-rich, InGaN nanostructure arrays on GaN/sapphire template

Uniform, dense, single-phase, 150 nm thick indium gallium nitride (InGaN) nanostructure (nanorods and nanostripes) arrays have been obtained on gallium nitride templates, by metal organic chemical vapor deposition and nanoscale selective area growth on silicon dioxide patterned masks. The 150 nm thick InGaN nanorods have a perfect hexagonal pyramid shape with relatively homogenous indium concentration up to 22%, which is almost twice as high as in planar InGaN grown in the same condition, and luminesce at 535 nm. InGaN nanostripes feature c-axis oriented InGaN in the core which is covered by InGaN grown along semi-polar facets with higher In content. Transmission electron microscope and sub micron beam X-rays diffraction investigations confirm that both InGaN nanostructures are mostly defect free and monocrystalline. The ability to grow defect-free thick InGaN nanostructures with reduced polarization and high indium incorporation offers a solution to develop high efficiency InGaN-based solar cells.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Crystallographic orientation of orthorhombic aragonite using reflection generalized ellipsometry

Here, the 2-modulator generalized ellipsometry microscope (2-MGEM) has been used to study a natural crystal of aragonite. Like its polymorph calcite, aragonite has a large refractive index difference between light polarized parallel to the c-axis and light polarized perpendicular to the c-axis. Unlike calcite, aragonite is orthorhombic, so there is also a very small difference between the refractive indices polarized along the a- and b-directions. As a result, it is not possible to use the 2-MGEM to obtain a definitive map of the optic axis directions of a sample as was possible with calcite, but it is possible to determine approximately the orientation of the c-axis with respect to the surface normal. If the c-axis is in the sample surface plane, it is possible to measure very small deviations of the c-axis direction with an accuracy of ~0.2°. If the c-axis is oriented normal to the sample surface, 2-MGEM data can be used to identify different crystallites due to rotations about the c-axis. For comparison, the orientations of some of the crystallites have also been measured using X-ray Laue and electron beam backscatter diffraction. In addition, spectroscopic generalized ellipsometry measurements have been used to determine the refractive indices of aragonite.

36 MATERIALS SCIENCE↗

Role of kinetic energy on Nb 3 Sn thin films by low-temperature co-sputtering

Nb 3 Sn is a promising thin film material for superconducting radio frequency (SRF) applications. Although surface resistivity, critical temperature, and critical field are advantageous in comparison to pure Nb, currently the performance of Nb 3 Sn is lacking behind due to its complex defect structure and phase inhomogeneities. In this work, the influence of the kinetic energy of the deposited particles on the defect structure in Nb 3 Sn thin films synthesized at low temperatures is investigated. A combination of extended x-ray absorption fine structure analysis, x-ray absorption spectroscopy mapping, and transmission electron microscopy reveals an improved local order and elemental homogeneity of the Nb 3 Sn films induced by higher kinetic energies of the elemental species during deposition. Even more, these process conditions lead to suppressed local inhomogeneities at grain boundaries, which can be one of the causes of critically reduced superconducting properties of low temperature sputter-coated Nb 3 Sn thin films. Finally, we show that the magnetic field-induced reduction of critical currents across weak-links formed at grain boundaries can be eliminated by the suggested materials’ synthesis.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

In situ ion irradiation of amorphous TiO 2 nanotubes

Understanding of structural and morphological evolution in nanomaterials is critical in tailoring their functionality for applications such as energy conversion and storage. Here, we examine irradiation effects on the morphology and structure of amorphous TiO 2 nanotubes in comparison with their crystalline counterpart, anatase TiO 2 nanotubes, using high-resolution transmission electron microscopy (TEM), in situ ion irradiation TEM, and molecular dynamics (MD) simulations. Anatase TiO 2 nanotubes exhibit morphological and structural stability under irradiation due to their high concentration of grain boundaries and surfaces as defect sinks. On the other hand, amorphous TiO 2 nanotubes undergo irradiation-induced crystallization, with some tubes remaining only partially crystallized. The partially crystalline tubes bend due to internal stresses associated with densification during crystallization as suggested by MD calculations. Furthermore, these results present a novel irradiation-based pathway for potentially tuning structure and morphology of energy storage materials.

36 MATERIALS SCIENCE↗

The resistance to embrittlement by a hydrogen environment of selected high strength iron-manganese base alloys

Fe-16Mn and Fe-25Mn base alloys, which had been cold worked to yield strength levels of 201 and 178 KSI, were resistant to degradation of mechanical properties in a one atmosphere hydrogen environment at ambient temperature under the loading conditions employed in this investigation. Transmission electron microscopy established that bands of epsilon phase martensite and fcc mechanical twins were formed throughout the fcc matrix when these alloys were cold worked. In the cold worked alloys a high density of crystal defects were observed associated with both types of strain induced structures, which should contribute significantly to the strengthening of these alloys. High strength iron base alloys can be produced which appear to have some resistance to degradation of mechanical properties in a hydrogen environment under certain conditions.

Benson, R. B., Jr.↗

Monte Carlo modeling of atomic oxygen attack of polymers with protective coatings on LDEF

Characterization of the behavior of atomic oxygen interaction with materials on the Long Duration Exposure Facility (LDEF) will assist in understanding the mechanisms involved, and will lead to improved reliability in predicting in-space durability of materials based on ground laboratory testing. A computational simulation of atomic oxygen interaction with protected polymers was developed using Monte Carlo techniques. Through the use of assumed mechanistic behavior of atomic oxygen and results of both ground laboratory and LDEF data, a predictive Monte Carlo model was developed which simulates the oxidation processes that occur on polymers with applied protective coatings that have defects. The use of high atomic oxygen fluence-directed ram LDEF results has enabled mechanistic implications to be made by adjusting Monte Carlo modeling assumptions to match observed results based on scanning electron microscopy. Modeling assumptions, implications, and predictions are presented, along with comparison of observed ground laboratory and LDEF results.

Banks, Bruce A.↗

Reduced gravitropic sensitivity in roots of a starch-deficient mutant of Nicotiana sylvestris

Gravitropism was studied in seedlings of Nicotiana sylvestris Speg. et Comes wild-type (WT) and mutant NS 458 which has a defective plastid phosphoglucomutase (EC 2.7.5.1.). Starch was greatly reduced in NS 458 compared to the WT, but small amounts of starch were detected in rootcap columella cells in NS 458 by light and electron microscopy. The roots of WT are more sensitive to gravity than mutant NS 458 roots since: (1) in mutant roots, curvature was reduced and delayed in the time course of curvature; (2) curvature of mutant roots was 24-56% that of WT roots over the range of induction periods tested; (3) in intermittent-stimulation experiments, curvature of mutant roots was 37% or less than that of WT roots in all treatments tested. The perception time, determined by intermittent-stimulation experiments, was < or = 5 s for WT roots and 30-60 s for mutant roots. The growth rates for WT and NS 458 roots were essentially equal. These results and our previous results with WT and starchless mutant Arabidopsis roots (Kiss et al. 1989, Planta 177, 198-206) support the conclusions that a full complement of starch is necessary for full gravitropic sensitivity and that amyloplasts function in gravity perception. Since a presumed relatively small increase in plastid buoyant mass (N. sylvestris mutant versus Arabidopsis mutant) significantly improves the orientation of the N. sylvestris mutant roots, we suggest that plastids are the likeliest candidates to be triggering gravity perception in roots of both mutants.

Non-NASA Center↗

Postirradiation Examination of the ATF-1 Experiments - 2019 Status

A collaborative effort of the Advanced Fuels Campaign together with industry consortia is focused on the development of enhanced accident tolerant fuels for Light Water Reactors (LWRs). The scoping studies, referred to as ATF-1 irradiations, are being performed in the Advanced Test Reactor of Idaho National Laboratory using drop-in style irradiations. The Post-Irradiation Examinations (PIEs) of ATF-1 began in 2017 and continued in 2019. This report describes the results of examinations on ATF-1 irradiations designed to test the performance of advanced iron-based cladding, including compatibility of FeCrAl with UO2, and ATF-1 irradiation of U3Si5. Two rodlets with commercial iron-based cladding and UO2 pellets have been irradiated to low burnup (i.e., < 20 GWd/tHM). The first rodlet had an Alloy33 cladding, while the other had a Kanthal APMT® cladding. The performed PIEs were focused on the determination of fuel microstructure, evaluation of fuel-cladding interaction and irradiation-induced variations of cladding mechanical properties. For both rodlets, no significant changes in the cladding hardness were measured, and the cladding hoop strain remained limited. Gamma tomography revealed no Cs axial migration as expected for LWR fuel, but significant cesium radial migration, which was induced by thermal migration consequent to high irradiation temperatures. Microstructure analyses revealed formation of secondary phases along the pellet rim of samples from both rodlets. No wastage or extensive chemical interaction between the fuel and the internal wall of the cladding was observed, suggesting that the secondary phases accumulated at the pellet rim might be due to formation of Cs-U-O compounds. However, further advanced PIEs are necessary to finally confirm this hypothesis. Optical microscopy analysis of the rodlet designed by Oak Ridge National Laboratory to evaluate the interaction between UO2 and various FeCrAl alloys revealed no extensive interaction in all the samples irradiated in the rodlet. Localized defects, namely circular pitting and cracks of a few tents of microns, were observed on the FeCrAl disc surfaces in some of the diffusion couples. These defects might be surface fabrication defects rather than irradiation-induced localized corrosion, but chemical analyses are needed to determine whether accumulation of corrosive fission products are causing enhanced interaction. Both non-destructive and destructive PIEs were collected on a rodlet containing U3Si5 fuel. The rodlet had extremely low fission gas release, similar to previously analyzed U3Si2 rodlets. Gamma tomography revealed thermo-migration of fission product ruthenium toward the center of the fuel pellet. The fuel microstructure resembles the as-fabricated microstructure, showing extensive microcracking related to the phase transition at 450°C. Two types of secondary phases were observed, which could either be due to segregation and precipitation of fission products or to UN impurities from fabrication. Finally, the current status of PIE on other ATF-1 irradiations will be discussed. These irradiations include UN-U3Si5 rodlets, UN-U3Si2 rodlets and an additional test with U3Si2 fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TiO{sub 2} nanotube arrays for photocatalysis: Effects of crystallinity, local order, and electronic structure

To furnish insight into correlations of electronic and local structure and photoactivity, arrays of short and long TiO{sub 2} nanotubes were synthesized by electrochemical anodization of Ti foil, followed by thermal treatment in O{sub 2} (oxidizing), Ar (inert), and H{sub 2} (reducing) environments. The physical and electronic structures of these nanotubes were probed with x-ray diffraction, scanning electron microscopy, and synchrotron-based x-ray absorption spectroscopy, and correlated with their photocatalytic properties. The photocatalytic activity of the nanotubes was evaluated by monitoring the degradation of methyl orange under UV-VIS light irradiation. Results show that upon annealing at 350 °C all as-anodized amorphous TiO{sub 2} nanotube samples partially transform to the anatase structure, with variations in the degree of crystallinity and in the concentration of local defects near the nanotubes' surface (∼5 nm) depending on the annealing conditions. Degradation of methyl orange was not detectable for the as-anodized TiO{sub 2} nanotubes regardless of their length. However, the annealed long nanotubes demonstrated detectable catalytic activity, which was more significant with the H{sub 2}-annealed nanotubes than with the Ar- and O{sub 2}-annealed nanotube samples. This enhanced photocatalytic response of the H{sub 2}-annealed long nanotubes relative to the other samples is positively correlated with the presence of a larger concentration of lattice defects (such as Ti{sup 3+} and anticipated oxygen vacancies) and a slightly lower degree of crystallinity near the nanotube surface. These physical and electronic structural attributes impact the efficacy of visible light absorption; moreover, the increased concentration of surface defects is postulated to promote the generation of hydroxyl radicals and thus accelerate the photodegradation of the methyl orange. The information obtained from this study provides unique insight into the role of the near-surface electronic and defect structure, crystal structure, and the local chemical environment on the photocatalytic activity and may be employed for tailoring the materials' properties for photocatalysis and other energy-related applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Split Ga vacancies and the unusually strong anisotropy of positron annihilation spectra in β–Ga 2 O 3

We report a systematic first-principles study on positron annihilation parameters in the β–Ga 2 O 3 lattice and Ga monovacancy defects complemented with orientation-dependent experiments of the Doppler broadening of the positron-electron annihilation. We find that both the β–Ga 2 O 3 lattice and the considered defects exhibit unusually strong anisotropy in their Doppler broadening signals. This anisotropy is associated with low symmetry of the β–Ga 2 O 3 crystal structure that leads to unusual kind of one-dimensional confinement of positrons even in the delocalized state in the lattice. In particular, the split Ga vacancies recently observed by scanning transmission electron microscopy produce unusually anisotropic positron annihilation signals. Furthermore, we show that in experiments, the positron annihilation signals in β–Ga 2 O 3 samples seem to be often dominated by split Ga vacancies.

36 MATERIALS SCIENCE↗

Comparison of three measurement modalities for 3D characterization of manufactured features and process-induced porosity in titanium alloy additively manufactured parts

Nondestructive characterization of internal features and defects within complex components is vital for many industrial applications, particularly with the advent of additive manufacturing (AM) technologies. However, community understanding of the limitations of nondestructive methods such as X-ray Computed Tomography (CT) can be limited in certain industrial sectors as these may be emergent applications. In this paper, we investigate the limits of X-ray CT measurements and compare extracted data with mechanical polishing serial sectioning (MPSS) and confocal laser scanning microscopy (CLSM). The test object is an additively manufactured titanium alloy disk that contains both process-induced porosity and machined features, including focused ion beam milled features designed to probe the resolution limits of X-ray CT. Results show that each of these characterization techniques has advantages and disadvantages. We compare data acquisition times, spatial resolution, geometric measurement accuracy and defect visualization fidelity across these modalities to establish a practical framework.

Additive manufacturing↗

Thermodynamic origin of nonvolatility in resistive memory

Electronic switches based on the migration of high-density point defects, or memristors, are poised to revolutionize post-digital electronics. Despite significant research, key mechanisms for filament formation and oxygen transport remain unresolved, hindering our ability to predict and design device properties. For example, experiments have achieved 10 orders of magnitude longer retention times than predicted by current models. Here, using electrical measurements, scanning probe microscopy, and first-principles calculations on tantalum oxide memristors, we reveal that the formation and stability of conductive filaments crucially depend on the thermodynamic stability of the amorphous oxygen-rich and oxygen-poor compounds, which undergo composition phase separation. Including the previously neglected effects of this amorphous phase separation reconciles unexplained discrepancies in retention and enables predictive design of key performance indicators such as retention stability. Furthermore, this result emphasizes non-ideal thermodynamic interactions as key design criteria in post-digital devices with defect densities substantially exceeding those of today’s covalent semiconductors.

36 MATERIALS SCIENCE↗

Impact of microstructure on the thermoelectric properties of the ternary compound Ce{sub 3}Cu{sub 3}Sb{sub 4}

We present detailed structural and thermoelectric studies of the ternary compound Ce{sub 3}Cu{sub 3}Sb{sub 4}. This material is of interest due to previously reported considerable thermopower above room temperature (∼ 100 μV/K) and low thermal conductivity (2 W/(m K)). Here, we present detailed studies concerning microstructural and thermoelectric data, their variation across the samples and possible explanations for the observed behaviour. We have used X-ray diffraction, scanning electron microscopy (SEM), and time-of-flight secondary ion mass spectrometry (TOF-SIMS) for microstructural analysis. The thermoelectric properties were examined using a physical property measurement system (PPMS). We analyse the impact of the sample quality on the thermoelectric properties. The most unstable parameter is the material resistivity which varies between 1.5 and 15 mΩ cm at room temperature. The properties variability is mainly due to structural defects caused by stresses during material preparation and also due to formation of foreign phases CeCuSb{sub 2} and CeSb. The figure of merit ZT is also strongly dependent on the quality of the sample. The largest value ZT ≈ 0.15 at 400 K is determined for the almost stoichiometric sample with small amounts of a impurity phases. - Highlights: •The Ce{sub 3}Cu{sub 3}Sb{sub 4} has considerable thermoelectric properties and potential for further chemical and/or structural modification. •The control over foreign phases formation is challenging. •The defects arising during arc melting process highly deteriorate ZT of material.

36 MATERIALS SCIENCE↗

In-plane and out-of-plane defectivity in thin films of lamellar block copolymers

We investigate the ordering of poly(styrene-b-methyl methacrylate) (PS-PMMA) lamellar copolymers (periodicity L 0 = 46 nm) confined between a free surface and brushed poly(styrene-r-methyl methacrylate) silicon substrate. The processing temperature was selected to eliminate wetting layers at the top and bottom interfaces, producing approximately neutral boundaries that stabilize perpendicular domain orientations. The PS-PMMA film thickness (t = 0.5L 0 –2.5L 0 ) and brush grafting density (Σ = 0.2–0.6 nm –2 ) were systematically varied to examine their impacts on in-plane and out-of-plane ordering. Samples were characterized with a combination of high-resolution microscopy, X-ray reflectivity, and grazing-incidence small-angle X-ray scattering. In-plane order at the top of the film (quantified through calculation of orientational correlation lengths) improved with t n , where the exponent n increased from 0.75 to 1 as Σ decreased from 0.6 to 0.2 nm –2 . Out-of-plane defects such as tilted domains were detected in all films, and the distribution of domain tilt angles was nearly independent of t and Σ. These studies demonstrate that defectivity in perpendicular lamellar phases is three-dimensional, comprised of in-plane topological defects and out-of-plane domain tilt, with little or no correlation between these two types of disorder. As a result, strong interactions between the block copolymer and underlying substrate may trap both kinds of thermally generated defects.

36 MATERIALS SCIENCE↗

Growth and properties of heavy fermion CeCu{sub 2}Ge{sub 2} and CeFe{sub 2}Ge{sub 2} thin films

Epitaxial films of heavy fermion CeCu{sub 2}Ge{sub 2} and CeFe{sub 2}Ge{sub 2} are grown on DyScO{sub 3} and MgO substrates using molecular beam epitaxy. The growth begins via island nucleation leading to a granular morphology. The grains grow flat with c-axis orientation after nucleating, as indicated by in-situ reflection high energy electron diffraction (RHEED) and ex-situ analysis including atomic force microscopy (AFM) and x-ray diffraction (XRD). These single phase films show similar temperature dependent transport to single crystals of the materials indicating that similar collective order occurs in the films as in single crystals.

36 MATERIALS SCIENCE↗

Inhomogeneous distribution of defect-related emission in Si-doped AlGaN epitaxial layers with different Al content and Si concentration

The spatial distribution of luminescence in Si-doped AlGaN epitaxial layers that differ in Al content and Si concentration has been studied by cathodoluminescence (CL) mapping in combination with scanning electron microscopy. The density of surface hillocks increased with decreasing Al content and with increasing Si concentration. The mechanisms giving rise to those hillocks are likely different. The hillocks induced surface roughening, and the compositional fluctuation and local donor-acceptor-pair (DAP) emission at hillock edges in AlGaN epitaxial layers were enhanced irrespective of the origin of the hillocks. The intensity of local DAP emission was related to Si concentration, as well as to hillock density. CL observation revealed that DAP emission areas were present inside the samples and were likely related to dislocations concentrated at hillock edges. Possible candidates for acceptors in the observed DAP emission that are closely related in terms of both Si concentration and hillock edges with large deformations are a V{sub III}-Si{sub III} complex and Si{sub N}, which are unfavorable in ordinary III-nitrides.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Refine your search to explore more results.