Search NASA⌕ Search

SEARCH · Search NASA

Results for “structured data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,801 records · Page 100

Robust decentralized control laws for the ACES structure

Control system design for the Active Control Technique Evaluation for Spacecraft (ACES) structure at NASA Marshall Space Flight Center is discussed. The primary objective of this experiment is to design controllers that provide substantial reduction of the line-of-sight pointing errors. Satisfaction of this objective requires the controllers to attenuate beam vibration significantly. The primary method chosen for control design is the optimal projection approach for uncertain systems (OPUS). The OPUS design process allows the simultaneous tradeoff of five fundamental issues in control design: actuator sizing, sensor accuracy, controller order, robustness, and system performance. A brief description of the basic ACES configuration is given. The development of the models used for control design and control design for eight system loops that were selected by analysis of test data collected from the structure are discussed. Experimental results showing that very significant performance improvement is achieved when all eight feedback loops are closed are presented.

Collins, Emmanuel G., Jr.↗

Spatial Resolution Estimation of LANDSAT-4 Thematic Mapper Data

The problem of estimating the overall point-spread function (PSF) of multispectral scanner systems was studied using real scene data and known geometric structures in the scene. A direct solution to an approximate form of the PSF was made along with a method using the derivative of an estimated edge response. Both results agreed closely. The TM scanner system specifications are given in line-spread function width and these values are listed with the experimental results in terms of meters. The estimated values are very reasonable, considering the number of factors which could be influencing the result. The atmosphere will have a blurring effect on the overall PSF as well as on cubic convolution resampling effects and possible electronic effects not accounted for in the specification. Also, the specific definition of the LSF specification is not known nor is the actual altitude at the instant the data were acquired. Thus the nominal overall PSF half-amplitude width of 39 m is reasonable; however, a greater sample of scene objects should be evaluated to furthur verify this result.

Mcgillem, C. D.↗

Build-Up Approach to Updating the Mock Quiet Spike Beam Model

When a new aircraft is designed or a modification is done to an existing aircraft, the aeroelastic properties of the aircraft should be examined to ensure the aircraft is flight worthy. Evaluating the aeroelastic properties of a new or modified aircraft can include performing a variety of analyses, such as modal and flutter analyses. In order to produce accurate results from these analyses, it is imperative to work with finite element models (FEM) that have been validated by or correlated to ground vibration test (GVT) data, Updating an analytical model using measured data is a challenge in the area of structural dynamics. The analytical model update process encompasses a series of optimizations that match analytical frequencies and mode shapes to the measured modal characteristics of structure. In the past, the method used to update a model to test data was "trial and error." This is an inefficient method - running a modal analysis, comparing the analytical results to the GVT data, manually modifying one or more structural parameters (mass, CG, inertia, area, etc.), rerunning the analysis, and comparing the new analytical modal characteristics to the GVT modal data. If the match is close enough (close enough defined by analyst's updating requirements), then the updating process is completed. If the match does not meet updating-requirements, then the parameters are changed again and the process is repeated. Clearly, this manual optimization process is highly inefficient for large FEM's and/or a large number of structural parameters. NASA Dryden Flight Research Center (DFRC) has developed, in-house, a Mode Matching Code that automates the above-mentioned optimization process, DFRC's in-house Mode Matching Code reads mode shapes and frequencies acquired from GVT to create the target model. It also reads the current analytical model, as we11 as the design variables and their upper and lower limits. It performs a modal analysis on this model and modifies it to create an updated model that has similar mode shapes and frequencies as those of the target model. The Mode Matching Code output frequencies and modal assurance criteria (MAC) values that allow for the quantified comparison of the updated model versus the target model. A recent application of this code is the F453 supersonic flight testing platform, NASA DFRC possesses a modified F-15B that is used as a test bed aircraft for supersonic flight experiments. Traditionally, the finite element model of the test article is generated. A GVT is done on the test article ta validate and update its FEM. This FEM is then mated to the F-15B model, which was correlated to GVT data in fall of 2004, A GVT is conducted with the test article mated to the aircraft, and this mated F-15B/ test article FEM is correlated to this final GVT.

Herrera, Claudia Y.↗

SPAR data set contents

The contents of the stored data sets of the SPAR (space processing applications rocket) finite element structural analysis system are documented. The data generated by each of the system's processors are stored in a data file organized as a library. Each data set, containing a two-dimensional table or matrix, is identified by a four-word name listed in a table of contents. The creating SPAR processor, number of rows and columns, and definitions of each of the data items are listed for each data set. An example SPAR problem using these data sets is also presented.

Cunningham, S. W.↗

Flutter clearance of the F-14 variable-sweep transition flight experiment airplane, phase 1

An F-14 airplane was modified to become the test bed aircraft for the variable sweep transition flight experiment (VSTFE) program. The latter is a laminar flow program designed to measure the effects of wing sweep on boundary layer transition from laminar to turbulent flow. The airplane was modified by adding an upper surface foam-fiberglass glove over a portion of the left wing. Ground vibration and flight flutter testing were accomplished to clear a sufficient flight envelope to conduct the laminar flow experiments. Flight test data indicated satisfactory damping levels and damping trends for the elastic structural modes of the airplane. The data presented include frequency and damping as functions of Mach number.

Kehoe, Michael W.↗

"Genetically Engineered" Nanoelectronics

The quantum mechanical functionality of nanoelectronic devices such as resonant tunneling diodes (RTDs), quantum well infrared-photodetectors (QWIPs), quantum well lasers, and heterostructure field effect transistors (HFETs) is enabled by material variations on an atomic scale. The design and optimization of such devices requires a fundamental understanding of electron transport in such dimensions. The Nanoelectronic Modeling Tool (NEMO) is a general-purpose quantum device design and analysis tool based on a fundamental non-equilibrium electron transport theory. NEW was combined with a parallelized genetic algorithm package (PGAPACK) to evolve structural and material parameters to match a desired set of experimental data. A numerical experiment that evolves structural variations such as layer widths and doping concentrations is performed to analyze an experimental current voltage characteristic. The genetic algorithm is found to drive the NEMO simulation parameters close to the experimentally prescribed layer thicknesses and doping profiles. With such a quantitative agreement between theory and experiment design synthesis can be performed.

Klimeck, Gerhard↗

Simple Analytical Expressions for Electron Pitch Angle Diffusion Coefficients

In the present paper, we have calculated electron pitch angle diffusion coefficients due to resonant interactions with whistler mode lower band chorus (LBC), upper band chorus (UBC), and electrostatic electron cyclotron harmonic (ECH) waves. Calculations have been performed at two values of the ratio of electron plasma frequency to gyro-frequency and thirteen representative values of electron energies for the plasma sheet electrons. The numerical data of diffusion coefficients have been fitted to simple analytical expressions for each wave mode. These analytical expressions allow for simple evaluation of pitch angle diffusion coefficients for the arbitrary pitch angle, energy, the ambient magnetic field, the wave amplitude, and the ratio of plasma frequency to gyro-frequency. In the case of LBC waves, the analytical coefficients are generally within a factor of two to the numerical coefficients, except at higher pitch angles where the numerical coefficients drop to show negligible values. Likewise, also for UBC waves, the analytical coefficients are generally within a factor of two to the numerical coefficients. The analytical coefficients for ECH waves are generally in agreement with numerical coefficients. However, the analytical expressions developed for ECH waves do not reproduce sharp fluctuations, dips, and gaps, the so-called banded structure observed in the data of numerical coefficients. The effect of the shape variation on the profile of the wave spectral intensity and the effect of cold temperature on the numerical coefficients are also investigated. Applications of the analytical expressions of diffusion coefficients are discussed.

coefficients↗

A real-time optical data processing device

The design, operation, and structure of the hybrid field effect light valve, a real-time input device for application to coherent optical data processing (CODP), is described. The device consists of a sandwich of thin films that electrically control the optical birefringence of a thin (2 micrometer) liquid crystal layer. It has high resolution (greater than 100 1/mm), contrast ratio (greater than 100:1), speed (10 sec on, 15 sec off) and input sensitivity (about 0.3 ergs/sq cm) in addition to cost and size advantages. Performance data for a laboratory model are presented.

Jacobson, A.↗

Phase and amplitude relationships of wave structure observed in the lower thermosphere

Data from the Atmosphere Explorer-C satellite clearly exhibit wavelike variations in neutral composition, ion density, and electron temperature, which appear to be a general feature of the atmosphere. The neutral constituents do not exhibit uniform wave characteristics since the density variations of argon are approximately twice those of molecular nitrogen and helium structure has about one-half the amplitude of the N2 variation. The waves evident in the ion density are nearly in phase with the heavy neutrals, while the electron-temperature variations are predominantly out of phase with those in the ion density. A simple model is suggested to explain the neutral composition results, wherein the enhancements in the major gas densities are in phase with the vertical component of the perturbation velocity of the gas. The vertical velocity modifies the composition by transporting parcels of air to higher or lower regions where the composition is different. The phase relationship between density and velocity implies phase velocities (assuming that these are gravitational waves) of the order of 500 meters per sec.

Reber, C. A.↗

Turbine Engine Disk Rotor Health Monitoring Assessment Using Spin Tests Data

Detecting rotating engine component malfunctions and structural anomalies is increasingly becoming a crucial key feature that will help boost safety and lower maintenance cost. However, achievement of such technology, which can be referred to as a health monitoring remains somewhat challenging to implement. This is mostly due to presence of scattered loading conditions, crack sizes, component geometry and material properties that hinders the simplicity of imposing such application. Different approaches are being considered to assist in developing other means of health monitoring or nondestructive techniques to detect hidden flaws and mini cracks before any catastrophic events occur. These methods extend further to assess material discontinuities and other defects that have matured to the level where a failure is very likely. This paper is focused on presenting data obtained from spin test experiments of a turbine engine like rotor disk and their correlation to the development of a structural health monitoring and fault detection system. The data collected includes blade tip clearance, blade tip timing measurements and shaft displacements. The experimental results are collected at rotational speeds up to 10,000 Rpm and tests are conducted at the NASA Glenn Research Center s Rotordynamics Laboratory via a high precision spin system. Additionally, this study offers a closer glance at a selective online evaluation of a rotating disk using advanced capacitive, microwave and eddy current sensor technology.

Abdul-Aziz, Ali↗

The object the metaphor the power and evergreen or the eighth way to make a hypermedia project fail

A patented software technique is described that is necessary and sufficient to keep hypermedia data bases current with the manufacturing technology. The technique proved its validity in four years of use in petrochemical plants. This technique is based on the following principles: (1) the data base must be object structured, i.e., all components must retain visible individuality; (2) the author must be seeing and experiencing the multimedia data objects as he creates; and (3) the hypermedia tools must possess power in the form of unlimited capacity.

Warren, Bruce A.↗

Application of the informational reference system OZhUR to the automated processing of data from satellites of the Kosmos series

The structure and potential of the information reference system OZhUR designed for the automated data processing systems of scientific space vehicles (SV) is considered. The system OZhUR ensures control of the extraction phase of processing with respect to a concrete SV and the exchange of data between phases.The practical application of the system OZhUR is exemplified in the construction of a data processing system for satellites of the Cosmos series. As a result of automating the operations of exchange and control, the volume of manual preparation of data is significantly reduced, and there is no longer any need for individual logs which fix the status of data processing. The system Ozhur is included in the automated data processing system Nauka which is realized in language PL-1 in a binary one-address system one-state (BOS OS) electronic computer.

Pokras, V. M.↗

Thermoplastic Space Point Design (TSPD) Tall Tower Lunar Thermal Analysis

The Thermoplastics Development for Exploration Applications (TDEA) project seeks to advance NASA’s thermoplastic composites capabilities by developing structurally efficient joining solutions for large-scale space structures to support NASA’s future exploration missions. A key objective is to develop and understand advanced thermoplastic joining techniques relevant to space environments and applicable to unitized and/or reconfigurable composite structures. The TDEA project uses NASA Langley’s Tall Lunar Tower (TLT) concept as a target application for the design and development of in-space assembled thermoplastic composites. TLT is a 50-meter-tall tower constructed on the lunar surface near the south pole. The tower’s height at this location on the moon allows for extended durations of incident solar flux which can be used to generate power via photovoltaic arrays. The thermal environment present on lunar south pole represents a challenging environment for any space-based asset. This study provides an overview of the analysis techniques used to determine the temperature extremes, gradients, and timelines of a tall composite tower over a one-year duration at the Shackleton Connecting Ridge. The developed thermal model includes tower and lunar surface elements with anisotropic and temperature-dependent material properties and incorporates a solar vector orbit with time-varying solar flux. Study topics include: a comparison between the effects of simplified lunar surface topologies on thermal results, prediction of surface temperature values versus Lunar Reconnaissance Orbiter (LRO) flight data, and tower structural-thermal deformation.

Lunar↗

Flammability of Epoxy Resins Containing Phosphorus

As part of a program to develop fire-resistant exterior composite structures for future subsonic commercial and general aviation aircraft, flame-retardant epoxy resins are under investigation. Epoxies and their curing agents (aromatic diamines) containing phosphorus were synthesized and used to prepare epoxy formulations. Phosphorus was incorporated within the backbone of the epoxy resin and not used as an additive. The resulting cured neat epoxy formulations were characterized by thermogravimetric analysis, propane torch test, elemental analysis, microscale combustion calorimetry, and fire calorimetry. Several formulations showed excellent flame retardation with phosphorous contents as low as 1.5% by weight. The fracture toughness and compressive strength of several cured formulations showed no detrimental effect due to phosphorus content. The chemistry and properties of these new epoxy formulations are discussed.

Flammability studies↗

Constraints on the Origin of Mercury’s Large Core from Core-Mantle Differentiation Models

Mercury’s core is notoriously large when compared to other planets of our solar system. The origin of this large core is still uncertain. Available data on the surface composition and internal structure of Mercury from the past MESSENGER mission and future data collected by BepiColombo will continue to provide clues to Mercury’s formation. Here, we present results combining experimental data on elemental distribution between core and mantle with spacecraft data, to estimate bulk Mercury composition. We applied this strategy to major elements (Fe, Si, Mg, Al and O), as well as minor elements (Cr and Ti), and compared derived compositions to chondritic data and the chemical compositions of the other terrestrial planets. Our results show that Mercury has a chemical composition significantly different from all known materials of the solar system. In addition, numerous scenarios were proposed to explain Mercury’s structure, including “chaotic models” such as giant impacts and “orderly models” such as aerodynamic sorting. Here, we tested whether Mercury’s composition can be explained by mantle stripping by impacts. We will show how such a scenario reconciles several features of Mercury’s geochemistry with chondritic data. We will also discuss the outlook of additional constraints from supplementary data potentially collected by BepiColombo.

Mercury↗

Determining Planetary Boundary Layer Height by Micro-pulse Lidar with Validation by UAV Measurements

Planetary boundary layer height (PBLH) is often used to characterize the structure of the lower atmosphere. Aerosol lidar, a ground-based remote sensing method, provides the vertical distribution of aerosol at a high temporal resolution observation data, from which, the PBL structure and the position of the PBL top can be comprehensively studied. PBLH determination with lidar data depends primarily on the characteristic turbulent motions in the atmosphere and the geophysical location. However, lidar determination of PBLH over densely populated subtropical locations has rarely been discussed; thus, developing retrieval techniques suitable to these areas is necessary. In this study, four PBLH determination methods (Gradient, δ–threshold, Haar wavelet transform, and hybrid image processing) are applied to estimate the PBLH from lidar observations over an urban area in East Asia, and one—the Gradient method—relied on potential temperature measurements from an unmanned aerial vehicle (UAV) flights to validate our results. Our results indicate that a combination of the gradient method and δ-threshold method can provide better results, in terms of diurnal pattern, than using either method individually. Furthermore, the Haar wavelet and the Hybrid image processing can detect the PBL development comparably well, but both methods are dependent on their initial conditions and optimized algorithm settings. In addition, the accompanying UAV observations are conclusively shown to have a high degree of efficacy for validating the lidar data. This research highlights that a combination of PBLH determination methods can better describe the PBLH evolution throughout a day in some cases, while in others less common determination methods are proving useful, and a suite of retrieval methods should still be explored for precisely mapping the PBL in densely populated subtropical areas.

Yueh-Chen Wang↗

Method for Real-Time State Estimation of Structural Modes for an Aeroelastic Wind Tunnel Model

A method for estimating displacements, velocities, and accelerations of structural modes in generalized coordinates from measured sensor data in real time is developed and demonstrated. Data from conventional strain gauges and fiber optic strain sensors (FOSS) were combined with strain mode shapes to produce least-squares estimates of the structural mode displacements. Similarly, accelerometer data were combined with displacement mode shapes to estimate structural mode accelerations. Estimates were then combined using a Kalman filter to refine the displacement estimates and produce structural mode velocity estimates. The approach was demonstrated using simulation data for the NASA-Boeing collaboration called the Integrated Adaptive Wing Technology Maturation (IAWTM) project in both a stable open-loop condition and an unstable condition where estimated displacement and velocity states were used for feedback control. Results supported the feasibility of using this approach for feedback control and system identification applications for wind tunnel tests.

Aeroservoelasticity↗

Implementing Geometric Surface Imperfections into Sandwich Composite Cylinder Finite Element Method Models

The buckling responses of certain cylindrical shell structures are extremely sensitive to geometric surface imperfections. The NASA Engineering and Safety Center (NESC) Shell Buckling Knockdown Factor Project (SBKF) is conducting research to develop analysis-based buckling design recommendations. Experiments are used to verify the analysis-based factors, but the sensitivity of the test articles to geometric imperfections requires implementing as-manufactured imperfections into high-fidelity finite element method models. Data collection methods such as structured light scanning are used for all geometric surface data used in this work. Common preprocessing and visualization steps used in SBKF are discussed, and steps on how surface scans are prepared for implementation into a finite element model is described. The Python Tool for Implementing Geometric Imperfections in Reduced Structures (Py_TIGIRS), written specifically for the use with SBKF, is briefly described and uses eight functions to extract, modify, and write geometric imperfections into Abaqus input files. Results of the pre-processing methods and results from Py_TIGIRS are provided and compared for Composite Test Article (CTA) 8.2B. Excellent agreement between the visualized scan data and the FEM-extracted geometry is demonstrated. A brief example of why geometric surface imperfections are significant in nonlinear numerical analyses for thin cylinders in axial compression is provided as motivation to use tools such as Py_TIGIRS. Future development of Py_TIGIRS including expansion to structures of arbitrary geometry is planned.

Sandwich structures↗

Refine your search to explore more results.