Search NASA⌕ Search

SEARCH · Search NASA

Results for “AIRPLANES - PERFORMANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Development and Flight Test of an Emergency Flight Control System Using Only Engine Thrust on an MD-11 Transport Airplane

An emergency flight control system that uses only engine thrust, called the propulsion-controlled aircraft (PCA) system, was developed and flight tested on an MD-11 airplane. The PCA system is a thrust-only control system, which augments pilot flightpath and track commands with aircraft feedback parameters to control engine thrust. The PCA system was implemented on the MD-11 airplane using only software modifications to existing computers. Results of a 25-hr flight test show that the PCA system can be used to fly to an airport and safely land a transport airplane with an inoperative flight control system. In up-and-away operation, the PCA system served as an acceptable autopilot capable of extended flight over a range of speeds, altitudes, and configurations. PCA approaches, go-arounds, and three landings without the use of any normal flight controls were demonstrated, including ILS-coupled hands-off landings. PCA operation was used to recover from an upset condition. The PCA system was also tested at altitude with all three hydraulic systems turned off. This paper reviews the principles of throttles-only flight control, a history of accidents or incidents in which some or all flight controls were lost, the MD-11 airplane and its systems, PCA system development, operation, flight testing, and pilot comments.

Burcham, Frank W., Jr.↗

Free-spinning-tunnel Investigation of a 1/30 Scale Model of a Twin-jet-swept-wing Fighter Airplane

An investigation has been made in the Langley 20-foot free-spinning tunnel to determine the erect and inverted spin and recovery characteristics of a 1/30-scale dynamic model of a twin-jet swept-wing fighter airplane. The model results indicate that the optimum erect spin recovery technique determined (simultaneous rudder reversal to full against the spin and aileron deflection to full with the spin) will provide satisfactory recovery from steep-type spins obtained on the airplane. It is considered that the air-plane will not readily enter flat-type spins, also indicated as possible by the model tests, but developed-spin conditions should be avoided in as much as the optimum recovery procedure may not provide satisfactory recovery if the airplane encounters a flat-type developed spin. Satisfactory recovery from inverted spins will be obtained on the airplane by neutralization of all controls. A 30-foot- diameter (laid-out-flat) stable tail parachute having a drag coefficient of 0.67 and a towline length of 27.5 feet will be satisfactory for emergency spin recovery.

Bowman, James S., Jr.↗

Subsonic Flight Tests of a 1/7-Scale Radio-Controlled Model of the North American X-15 Airplane with Particular Reference to High Angel-of-Attack Conditions

An investigation of the subsonic stability and control characteristics of an unpowered 1/7-scale model based on the North American X-15 airplane was conducted by using a radio-controlled model launched from a helicopter and flown in free-gliding flight. At angles of attack below about 20 deg. where the model motions represent those of the X-15 airplane, the model was found to be both longitudinally and laterally stable, and the all-movable tail surfaces were found to be very effective. The model could also be flown at much higher angles of attack where the model motions did not necessarily represent those of the airplane because of slight geometrical differences and Reynolds number effects, but these test results are useful in evaluating the effectiveness at these angles of the type of lateral control system used in the X-15 airplane. In some cases, the model was flown to angles of attack as high as 60 or 70 deg. without encountering divergent or uncontrollable conditions. For some flights in which the model was subjected to rapid maneuvers, spinning motions were generated by application of corrective controls to oppose the direction of rotation. Rapid recoveries from this type of motion were achieved by applying roll control in the direction of rotation.

Hewes, Donald E.↗

Free-Spinning Characteristics of a 1/30-Scale Model of the Grumman WF-2 Airplane

An investigation was conducted in the Langley 20-foot free-spinning tunnel on a 1/30-scale model of the Grumman WF-2 airplane. The effects of control settings and movements upon the erect-spin and recovery characteristics for the flight gross-weight loading with normal center-of-gravity and rearward center-of-gravity positions were determined. For the inverted-spin tests, the flight gross-weight loading with normal center-of-gravity position was used. Brief tests were also made with the radome removed to determine the effect of the radome on the spin and recovery characteristics of the airplane. The results of the tests of the model indicate that erect spins of the airplane in the flight gross-weight loading with the normal (26.3-percent mean aerodynamic chord) center-of-gravity position and with the most rearward (30-percent mean aerodynamic chord) center-of-gravity position possible will be satisfactorily terminated by full rudder reversal to against the spin accompanied by movement of the elevator to at least two-thirds down. With the radome removed, the spin will be steeper and considerably more oscillatory than with the radome on. Recoveries by the preceding technique will be satisfactory. Inverted spins of the airplane will be satisfactorily terminated by full rudder reversal followed by neutralization of the longitudinal and lateral controls.

Lee, Henry A.↗

Free-Spinning-Tunnel Investigation of a 1/40-Scale Model of the McConnell F-101A Airplane

An investigation has been made in the Langley 20-foot free-spinning tunnel of a 1/40-scale model of the McDonnell F-101A airplane to alleviate the unfavorable spinning characteristics encountered with the airplane. The model results indicate that a suitable strake extended on the inboard side of the nose of the airplane (right side in a right spin) in conjunction with the use of optimum control recovery technique will terminate spin rotation of the airplane. It may be difficult to recover from subsequent high angle-of-attack trimmed flight attitudes even by forward stick movement. The optimum spin-recovery control technique for the McDonnell F-101A is simultaneous full rudder reversal to against the spin and aileron movement to full with the spin (stick full right in a right erect spin) and forward movement of the stick immediately after rotation stops.

Bowman, James S., Jr.↗

Evaluation of Several Approximate Methods for Calculating the Symmetrical Bending-Moment Response of Flexible Airplanes to Isotropic Atmospheric Turbulence

Several approximate procedures for calculating the bending-moment response of flexible airplanes to continuous isotropic turbulence are presented and evaluated. The modal methods (the mode-displacement and force-summation methods) and a matrix method (segmented-wing method) are considered. These approximate procedures are applied to a simplified airplane for which an exact solution to the equation of motion can be obtained. The simplified airplane consists of a uniform beam with a concentrated fuselage mass at the center. Airplane motions are limited to vertical rigid-body translation and symmetrical wing bending deflections. Output power spectra of wing bending moments based on the exact transfer-function solutions are used as a basis for the evaluation of the approximate methods. It is shown that the force-summation and the matrix methods give satisfactory accuracy and that the mode-displacement method gives unsatisfactory accuracy.

Bennett, Floyd V.↗

Exploring Venus by Solar Airplane

A solar-powered airplane is proposed to explore the atmospheric environment of Venus. Venus has several advantages for a solar airplane. At the top of the cloud level, the solar intensity is comparable to or greater than terrestrial solar intensities. The Earthlike atmospheric pressure means that the power required for flight is lower for Venus than that of Mars, and the slow rotation of Venus allows an airplane to be designed for continuous sunlight, with no energy storage needed for night-time flight. These factors mean that Venus is perhaps the easiest planet in the solar system for flight of a long-duration solar airplane.

Landis, Geoffrey A.↗

A Study of Transport Airplane Crash-Resistant Fuel Systems

This report presents the results of a study, funded by the Federal Aviation Administration (FAA), of transport airplane crash-resistant fuel system (CRFS). The report covers the historical studies related to aircraft crash fires and fuel containment concepts undertaken by the FAA, NASA, and the U.S. Army, which ultimately led to the current state of the art in CRFS technology. It describes the basic research, testing, field investigations and production efforts which have led to the highly successful military CRFS, which has saved many lives and reduced costs of accidents. Current CRFS technology used in transport category airplanes is defined and compared to the available state-of-the-art technology. The report provides information to the FAA and other government organizations which can help them plan their efforts to improve the state of crash fire protection in the transport airplane fleet. The report provides guidance to designers looking for information about CRFS design problems, analysis tools to use for product improvement, and a summary of current and proposed regulations for transport category airplane fuel systems.

Jones, Lisa↗

Launch Characteristics of the X-15 Research Airplane as Determined in Flight

The first 16 air launches of the X-15 airplane demonstrated the feasibility of air launch from an asymmetric position under the wing of the B-52 carrier airplane. With all dampers operating, launch transients were minimized and no stability problems were encountered. But, when the roll damper failed to function, the X-15 experienced relatively large roll rates in the presence of the carrier airplane, creating the possibility of the X-15 upper vertical tail hitting the cutout in the B-52 wing. Specific flight data demonstrated that left-aileron settings of from 6 deg to 8 deg at launch minimized the right-roll transient. The altitude loss of 3,000 to 9,000 feet before climbout could be effected was a function of launch altitude and recovery angle of attack. The average time for the X-15 to separate 10 feet from the B-52 carrier airplane was about 0.8 second. Flight-measured separation rates and launch transients agree well with predicted values where the initial conditions and control motions are similar.

Matranga, Gene J.↗

Wind-Tunnel Tests of a 1/8-Scale Powered Model of the XTB3F-1 Airplane, TED No. NACA 2382

A 1/8 scale model of the Grumman XTB3F-1 airplane was tested in the Langley 7- by 10-foot tunnel to determine the stability and control characteristics and to provide data for estimating the airplane handling qualities. The report includes longitudinal and lateral stability and control characteristics of the complete model, the characteristics of the isolated horizontal tail, the effects of various flow conditions through the jet duct, tests with external stores attached to the underside of the wing, ana tests simulating landing and take-off conditions with a ground board. The handling characteristics of the airplane have not been computed but some conclusions were indicated by the data. An improvement in the longitudinal stability was obtained by tilting the thrust line down. It is shown that if the wing flap is spring loaded so that the flap deflection varies with airspeed, the airplanes will be less stable than with the flap retracted or fully deflected. An increase in size of the vertical tail and of the dorsal fin gave more desirable yawing-moment characteristics than the original vertical tail and dorsal fin. Preventing air flow through the jet duct system or simulating jet operation with unheated air produced only small changes in the model characteristics. The external stores on the underside of the wing had only small effects on the model characteristics. After completion of the investigation, the model was returned to the contractor for modifications indicated by the test results.

McKee, John W.↗

Data Obtained in the Flight Measurements to Determine the Stability and Control Characteristics of a C-54D Airplane (AAF No. 42-72713) and a Summary of the Test Program

The flight investigation of the C-54D airplane was initiated to determine the necessity of changes or additions to existing handling-qualities requirements to cove the case of instrument approaches with large airplanes. This paper gives a brief synopsis of the results and presents the measured data of tests to determine the stability and control characteristics. It was found that no new requirements were necessary to cover the problems of instrument approaches. The C-54D airplane tested met the Amy and Navy stability and control requirements except for the following items. The control-system friction with autopilot installed vas double that allowed by the requirements. The amount of friction was found to impair the controllability of the airplane in precision flying. The lateral and directional characteristics were good except that the maximum pb/2V was slightly below the minimum required, and the elevator-control forces to obtain the maximum pb/2V at low speeds were above the Army and Navy requirements. The longitudinal stability and control characteristics were good except that the elevator-control forces exceeded the limits of the Army and Navy requirements in turns and in landings. The stalling characteristics were considered good in all conditions with the stall warning in the form of tail buffeting occurring at speeds approximately 5 miles per hour above the stall.

Talmage, Donald B.↗

Spin and Recovery Characteristics of the Curtiss-Wright XP-87 Airplane

The spin and recovery characteristics of the Curtiss-Wright XP-87 airplane, as well as the spin-recovery parachute requirements, the control forces that would be encountered in the spin, and the best method for the crew to attempt an emergency escape, are presented in this report. The characteristics were estimated rather than determined by model tests because the XP-87 dimensional and mass characteristics were considered to be noncritical and because data were available from model tests of several similar airplanes. The study indicated that the recovery characteristics of the airplane will be satisfactory for all loadings if the controls are reversed fully and rapidly. The control forces, however, will probably be beyond the capabilities of the pilot unless some additional balance or a booster is used. A 6-foot tail parachute or a 3.5-foot wing-tip parachute with a drag coefficient of 0.7 will be a satisfactory, emergency spin-recovery device for spin demonstrations. If it is necessary for the crew to abandon the spinning airplane, they should leave from the outboard side of the cockpit.

Berman, Theodore↗

Ditching Investigation of a 1/12-Scale Model of the Douglas F4D-1 Airplane, TED No. NACA DE 384

A ditching investigation was made of a l/l2-scale dynamically similar model of the Douglas F4D-1 airplane to study its behavior when ditched. The model was landed in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and configurations were investigated. The behavior of the model was determined from visual observations, acceleration records, and motion-picture records of the ditchings. Data are presented in tables, sequence photographs, time-history acceleration curves, and attitude curves. From the results of the investigation, it was concluded that the airplane should be ditched at the lowest speed and highest attitude consistent with adequate control (near 22 deg) with landing gear retracted. In a calm-water ditching under these conditions the airplane will probably nose in slightly, then make a fairly smooth run. The fuselage bottom will sustain appreciable damage so that rapid flooding and short flotation time are likely. Maximum longitudinal deceleration will be about 4g and maximum normal acceleration will be about 6g in a landing run of about 420 feet, In a calm-water ditching under similar conditions with the landing gear extended, the airplane will probably dive. Maximum longitudinal decelerations will be about 5-1/2g and maximum normal accelerations will be about 3-1/2g in a landing run of about 170 feet.

Windham, John O.↗

Ditching Investigation of a 1/24-Scale Model of the Boeing B-47 Airplane

An investigation of a 1/24-scale dynamically similar model of the Boeing B-47 airplane was made to determine the ditching characteristics and proper ditching technique for the airplane. Various conditions of damage, landing attitude, flap setting, and speed were investigated. The behavior of the model was determined from visual observations, motion-picture records, and time-history deceleration records. The results of the investigation are presented in table form, photographs, and curves. The airplane should be ditched at the lowest speed and highest attitude consistent with adequate control; the flaps should be full down. The airplane will probably make a deep but fairly smooth run. The fuselage bottom will be damaged and partially filled with water; consequently, crew members should be assigned ditching stations near an exit in the upper or forward part of the fuselage. The nacelles may be expected to be torn away from the wing. In calm water the maximum decelerations will be about 3g and the landing run will be about 6 fuselage lengths.

Fisher, Lloyd J.↗

Investigations on the Stability, Oscillation, and Stress Conditions of Airplanes with Tab Control: First Partial Report. Derivation of the Equations of Motion and their General Solutions

For the design and the construction of airplanes the control is of special significance, not only with regard to the flight mechhnical properties but also for the proportional arrangement of wing unit, fuselage, and tail unit. whereas these problems may be regarded as solved for direct control of airplane motions, that is, for immediate operation of the control surfaces, they are not clarified as to oscimtions, stability, and stress phenomena occurring in flight motions with Indirect control, ss realized for instance in tab control. Its modus operandi is based on the activation of a tab hinged to the trailing edge & the main control surface. Due to lift and drag variations, mcments originate about the axis of rotation of the main contnol surface which cause an up-or--down floating of the main control surface and thus a change in the direction of the airplane. Since this tab control means flying with free control surface , the treatment of this problem should provide the basis on which to judge stability, oscilhtton, and stress data.The present report is to represent a contribution toward the clarification of the problems arising and, to treat the longitudinal motion of an airplane.

Filzek, B.↗

Ditching Investigation of a 1/24-Scale Model of the Douglas C-124 Airplane

An investigation of a 1/24- scale dynamically similar model of the Douglas C-124 airplane was made to determine the ditching characteristics and proper technique for ditching the airplane. Various conditions of damage, landing attitude, flap setting, and speed were investigated. The behavior of the model was determined from visual observations, motion- picture records, and time-history deceleration records. The results of the investigation are presented in table form, photographs, and curves. It was concluded on the basis of results from model tests with scale-strength bottoms (equivalent to 1150 pounds per square foot, full scale) that the airplane should be ditched at a medium nose-high landing attitude (near 7deg) with flaps full down. The airplane will probably make a smooth run with considerable damage resulting to the fuselage bottom just forward of the wing, but it is not likely that the water inflow will be overwhelming to personnel provided they are not in the belly compartment. Longitudinal decelerations in calm water will be about 2 1/2g and the landing run will be about four fuselage lengths.

Fisher, Lloyd J.↗

Flight Investigation of the Stability and Control Characteristics of a 0.13-Scale Model of the Convair XFY-1 Vertically Rising Airplane During Constant-Altitude Transitions, TED No. NACA DE 368

An investigation is being conducted to determine the dynamic stability and control characteristics of a 0.13-scale flying model of the Convair XFY-1 vertically rising airplane. This paper presents the results of flight tests to determine the stability and control characteristics of the model during constant-altitude slow transitions from hovering to normal unstalled forward flight. The tests indicated that the airplane can be flown through the transition range fairly easily although some difficulty will probably encountered in controlling the yawing motions at angles of attack between about 60 and 40. An increase in the size of the vertical tail will not materially improve the controllability of the yawing motions in this range of angle of attack but the use of a yaw damper will make the yawing motions easy to control throughout the entire transitional flight range. The tests also indicated that the airplane can probably be flown sideways satisfactorily at speeds up to approximately 33 knots (full scale) with the normal control system and up to approximately 37 knots (full scale) with both elevons and rudders rigged to move differentially for roll control. At sideways speeds above these values, the airplane will have a strong tendency to diverge uncontrollably in roll.

Lovell, Powell M., Jr.↗

Ditching Investigation of a 1/14-Scale Model of the Northrop C-125 Airplane

An investigation of a 1/14-scale dynamically similar model of the Northrop C-125 airplane was made to determine the ditching characteristics and proper ditching technique for the airplane. Various conditions of damage, landing attitude, flap setting, and speed were investigated. The behavior of the model was determined from visual observations, motion-picture records, and time-history deceleration records. The results of the investigation are presented in table form, photographs, and curves. It was concluded that the airplane should be ditched at a nose-high landing attitude (near 8 deg) with flaps full down. The fixed landing gear will cause the airplane to dive. The fuselage will be damaged and will probably flood rapidly. Longitudinal decelerations will be about 4g and the length of landing run will be about two fuselage lengths. If the main landing gear could be jettisonable or retractable the ditching characteristics would be greatly improved.

Fisher, Lloyd J.↗