Search NASA⌕ Search

SEARCH · Search NASA

Results for “ARISE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Thermocapillary flow with evaporation and condensation and its effect on liquid retention in low-G fluid acquisition devices

The steady motion, thermal and free surface behavior of a volatile, wetting liquid in microgravity are studied using scaling and numerical techniques. The objective is to determine whether the thermocapillary and two-phase convection arising from thermodynamic nonequilibrium along the porous surfaces of spacecraft liquid acquisition devices could cause the retention failures observed with liquid hydrogen and heated vapor pressurant. Why these devices seem immune to retention loss when pressurized with heated helium or heated directly through the porous structure was also examined. Results show that highly wetting fluids exhibit large negative and positive dynamic pressure gradients towards the meniscus interline when superheated and subcooled, respectively. With superheating, the pressure variation and recoil force arising from liquid/vapor phase change exert the same influence on surface morphology and promote retention. With subcooling, however, the pressure distribution produces a suction that degrades mechanical equilibrium of the surface. This result indicates that thermocapillary-induced deformation arising from subcooling and condensation is the likely cause for retention loss. In addition, increasing the level of nonequilibrium by reducing accommodation coefficient suppresses deformation and explains why this failure mode does not occur in instances of direct screen heating or pressurization with a heated inert gas.

Schmidt, George R.↗
NASA NTRS1994

Experimental investigation of turbine blade-tip excitation forces

Results of a program to investigate the magnitude and parametric variations of rotordynamic forces which arise in high power turbines due to blade-tip leakage effects are presented. Five different unshrouded turbine configurations and one configuration shrouded with a labyrinth seal were tested with static offsets of the turbine shaft. The forces along and perpendicular to the offset were measured directly with a rotating dynometer. Exploration of casing pressure and flow velocity distributions was used to investigate the force-generating mechanisms. For unshrouded turbines, the cross-forces originate mainly from the classical Alford mechanisms while the direct forces arise mainly from a slightly skewed pressure pattern. The Alford coefficient for cross-force was found to vary between 2.4 and 4.0, while the similar direct force coefficient varied from 1.5 to 3.5. The cross-forces are found to increase substantially when the gap is reduced from 3.0 to 1.9% of blade height, probably due to viscous blade-tip effects. The forces also increase when the hub gap between stator and rotor decreases. The force coefficient decreased with operating flow coefficient. In the case of the shrouded turbine, most of the forces arise from nonuniform seal pressures. This includes about 80% for the transverse forces. The rest appears to come from uneven work extraction. Their level is about 50% higher in the shrouded case.

Martinez-Sanchez, Manuel↗
NASA NTRS1994

The in situ exobiological investigation of the Martian surface mineralogy during unmanned missions

An important goal of exobiological research is to determine if life arose on planets other than Earth. The only other planet known, to date, on which life may have arisen is Mars. The data suggest that the physical environment of early Mars (i.e., temperature, pressure, and radiation regimes) was suitable for life to arise. Thus far, the data also suggest that early Mars possessed sufficient quantities of the required building blocks and a number of the chemical compounds necessary for life to arise. It is not known, however, if water existed in the appropriate state (i.e., liquid) in sufficient quantities long enough for life to arise. Determining the mineralogy and components of the Martian soil through in situ analyses during missions to Mars will provide information from which an assessment can be made for the probability of the origin of life on Mars. Missions to Mars in the near future will be unmanned and capable of in situ analyses. Our studies have shown that differential thermal analysis coupled with gas chromatography (DTA/GC) is a more appropriate analytical technique than, x-ray fluorescence, x-ray diffraction, alpha-proton backscatter, gamma-ray spectrometry, differential scanning calorimetry coupled with mass spectrometry (DSC/MS), or DSC/GC to identify the mineralogy of the Martian surface material in situ. DTA/GC is an advancement over the pyrolytic techniques flown on previous missions that have supplied only limited mineralogical information (Biemann et al. 1977).

Mancinelli, Rocco L.↗
NASA NTRS1993

The spectrum of Orion-KL at 2 millimeters (150-160 GHz)

A spectral survey of Orion-KL has been carried out in the 2 mm atmospheric window in the frequency range 149.6-159.6 GHz, using the FCRAO 14 m telescope. Typical sensitivities achieved were T(sub A sup *) approximately 0.03-0.1 K, peak-to-peak. Over 180 spectral lines were detected, including approximately 45 unidentified features. The spectra were measured with a single-sideband receiver and, even at levels of T(sub A sup *) approximately 30 mK, are far from being confusion-limited. Fifteen known species were conclusively identified in Orion in this spectral region, with the largest numbers of lines arising from methyl formate, ethyl cyanide, methanol, and dimethyl ether. These species have beam-averaged column densities of N(sub tot) approximately 0.5-8 x 10(exp 15)/sq cm. Several other species have been tentatively observed, including acetaldehyde, C2S, and possibly EtOH. The large organic species, however, appear to arise from different regions. For example, CH3CCH and (CH3)2O come primarily from the extended ridge, while EtCN and VyCN exclusively arise in the hot core. This survey clearly demonstrates that the 2 mm window is rich in spectral lines. It also suggests there is much chemical selectivity in the formation of large organic interstellar molecules.

Ziurys, L. M.↗
NASA NTRS1994

Highly ionized gas in the Galactic halo

We reexamine the values of electron density n(sub e) and gas pressure P/k in the interstellar medium (ISM) of the Galactic halo, as inferred from C IV emission and absorption lines and using current C IV atomic data. In a homogeneous model with 4.7 less than or equal to log T less than or equal to 5.3, the data are consistent with 0.01 less than or equal to n(sub e) less than or equal to 0.02/cu cm and 2200 less than or equal to P/k less than or equal to 3700/cu cm K, a factor of 2-3 higher than advocated by Martin & Bowyer (1990) and comparable to the thermal pressure in the disk. If some of the C IV absorption arises from nonemitting, photoionized gas, then the inferred density and pressure will increase accordingly. The volume filling factor for homogeneous models ranges from 0.5% to 5%. Because of the constraints arising from filling factor and radiated power, most of the C IV must arise from gas near the peak of the cooling curve, at log t less than or equal to 5.6. We relate both emission-line and absorption-line observations to recent models in which turbulent mixing layers and isobarically cooling supernova remnants (SNRs) provide significant amounts of halo gas at approximately 10(exp 5.3) K and process 20-40 solar mass/yr with a power of approximately 10(exp 41) ergs/sec. Since the observed C IV and N V absorption scale heights have been reported to differ, at 4.9 kpc and 1.6 kpc, respectively, we examine inhomogeneous models with different exponential scale heights of T, P, and SN energy input. The ISM may change its character with distance above the Galactic plane, as superbubbles and mixing layers dominate over isolated SNRs as the source of the C IV. For appropiate scale heights, the midplane pressure is twice the homogeneous values quoted above. The O IV lambda 1034 diffuse emission line, which can be used as a temperature diagnostic of the hot gas, is predicted to be comparable in strength to that of C IV lambda 1549 (approximately 6000 photons/cu cm/s/sr. The ions C IV, N V, and O VI are predicted to show a decreasing trend in vertical extent, with the O IV scale height perhaps as low as approximately 1 kpc.

Shull, J. Michael↗
NASA NTRS1996

The Surfaces of Pluto and Charon

Much of the surface of Pluto consists of high-albedo regions covered to an unknown depth by Beta-N2, contaminated with CH4, CO, and other molecules. A portion of the exposed surface appears to consist of solid H2O. The remainder is covered by lower albedo material of unknown composition. The N2 ice may occur as polar caps of large extent, leaving ices and other solids of lower volatility in the equatorial regions. The low-albedo material found primarily in the equatorial regions may consist in part of solid hydrocarbons and nitriles produced from N2 and CH4 in the atmosphere or in the surface ices. Alternatively, it may arise from deposition from impacting bodies and/or the chemistry of the impact process itself. Charon's surface is probably more compositionally uniform than that of Pluto, and is covered by H2O ice with possible contaminants or exposures of other materials that are as yet unidentified. The molecular ices discovered on Pluto and Charon have been identified from near-infrared spectra obtained with Earth-based telescopes. The quantitative interpretation of those data has been achieved through the computation of synthetic spectra using the Hapke scattering theory and the optical constants of various ices observed in the laboratory. Despite limitations imposed by the availability of laboratory data on ices in various mixtures, certain specific results have been obtained. It appears that CH4 and CO are trace constituents, and that some fraction of the CH4 (and probably the CO) on Pluto is dissolved in the matrix of solid N2. Pure CH4 probably also occurs on Pluto's surface, allowing direct access to the atmosphere. Study of the nitrogen absorption band at 2.148 micrometers shows that the temperature of the N2 in the present epoch is 40 +/-2 K. The global temperature regime of Pluto can be modeled from observations of the thermal flux at far-infrared and millimeter wavelengths. The low-albedo equatorial regions must be significantly warmer than the polar regions covered by N2 (at T = 40 K) to account for the total thermal flux measured. At the present season, the diurnal skin depth of the insolation-driven thermal wave is small, and the observed mm-wave fluxes may arise from a greater depth. Alternatively, the mm-wave flux may arise from the cool, sublimation source region. The surface microstructure in the regions covered by N2 ice is likely governed by the sintering properties of this highly volatile material. The observed nitrogen infrared band strength requires that expanses of the surface be covered with cm-sized crystals of N2. Grains of H2O ice on Charon, in contrast, are probably of order 50 micrometers in size, and do not metamorphose into larger grains at a significant rate. Because of the similarities in size, density, atmosphere and surface composition between Pluto and Neptune's satellite Triton, the surface structures observed by Voyager on Triton serve as a plausible paradigm for what might be expected on Pluto. Such crater forms, tectonic structures, aeolian features, cryovolcanic structures, and sublimation-degraded topography as are eventually observed on Pluto and Charon by spacecraft will give information on their interior compositions and structures, as well as on the temperature and wind regimes over the planet's extreme seasonal cycle.

Cruikshank, Dale P.↗
NASA NTRS1997

Mid Infrared Hydrogen Recombination Line Emission from the Maser Star MWC 349A

We have detected and spectrally resolved the mid-IR hydrogen recombination lines H6(alpha)(12.372 micrometers), H7(alpha)(19.062 micrometers), H7(beta)(l1.309 micrometers) and H8(gamma)(12.385 micrometers) from the star MWC349A. This object has strong hydrogen maser emission (reported in the millimeter and submillimeter hydrogen recombination lines from H36(alpha) to H21(alpha)) and laser emission (reported in the H15(alpha), H12(alpha) and H10(alpha) lines). The lasers/masers are thought to arise predominantly in a Keplerian disk around the star. The mid-IR lines do not show evident signs of lasing, and can be well modeled as arising from the strong stellar wind, with a component arising from a quasi-static atmosphere around the disk, similar to what is hypothesized for the near IR (less than or equal to 4 micrometers) recombination lines. Since populations inversions in the levels producing these mid-IR transitions are expected at densities up to approximately 10(exp 11)/cu cm, these results imply either that the disk does not contain high-density ionized gas over long enough path lengths to produce a gain approximately 1, and/or that any laser emission from such regions is small compared to the spontaneous background emission from the rest of the source as observed with a large beam. The results reinforce the interpretation of the far-IR lines as true lasers.

Smith, Howard A.↗
NASA NTRS1999

Exploiting the Temperature/Concentration Dependence of Magnetic Susceptibility to Control Convection in Fundamental Studies of Solidification Phenomena

The objective of this new research project is to demonstrate by experiment, supplemented by mathematical modeling and physical property measurement, that the effects of buoyancy driven convection can be largely eliminated in ground-based experiments, and further reduced in flight, by applying a new technique. That technique exploits the dependence of magnetic susceptibility on composition or temperature. It is emphasized at the outset that the phenomenon to be exploited is fundamentally and practically different from the magnetic damping of convection in conducting liquids that has been the subject of much prior research. The concept suggesting this research is that all materials, even non-conductors, when placed in a magnetic field gradient, experience a force. Of particular interest here are paramagnetic and diamagnetic materials, classes which embrace the "model alloys", such as succinonitrile-acetone, that have been used by others investigating the fundamentals of solidification. Such alloys will exhibit a dependence of susceptibility on composition. The consequence is that, with a properly oriented field (gradient) a force will arise that can be made to be equal to, but opposite, the buoyancy force arising from concentration (or temperature) gradients. In this way convection can be stilled. The role of convection in determining the microstructure, and thereby properties, of materials is well known. Elimination of that convection has both scientific and technological consequences. Our knowledge of diffusive phenomena in solidification, phenomena normally hidden by the dominance of convection, is enhanced if we can study solidification of quiescent liquids. Furthermore, the microstructure, microchemistry and properties of materials (thereby practical value) are affected by the convection occurring during their solidification. Hitherto the method of choice for elimination of convection has been experimentation in microgravity. However, even in low Earth orbit, residual convection has effects. That residual convection arises from acceleration (drag on the spacecraft), displacement from the center of mass or transients in the gravitational field (g-jitter). There is therefore a need for both further reducing buoyancy driven flow in flight and allowing the simulation of microgravity during ground based experiments. Previous investigations, the research project description, theory behind the study and experimental methods as well as plots of magnetic fields and forces are presented.

Evans, J. W.↗
NASA NTRS1997

The Structure of the Statocyst of the Freshwater Snail Biomphalaria Glabrata (Pulmonata, Basommatophora)

The structure of the statocyst of the freshwater snail Biomphalaria glabrata has been examined by light and electron microscopy. The two statocysts are located on the dorsal-lateral side of the left and right pedal ganglion. The statocysts are spherical, fluid-filled capsules with a diameter of approximately 60 microns for young and 110 microns for adult snails. The wall of the cyst is composed of large receptor cells and many smaller supporting cells. The receptor cells bear cilia which are evenly distributed on the apical surface. The cilia have the typical 9+2 internal tubule configuration. Striate rootlets originate from the base of the basal body and run downward into the cytoplasm. Side-roots arise from one side of the basal body and a basal foot from the other. For each receptor cell, the basal foot always points to the periphery of the surface, indicating that the receptor cell is non-polarized. The receptor cells contain cytoplasmic organelles such as mitochondria, ribosomes, rough and smooth endoplasmic reticulum, compact Golgi bodies and multivesicular bodies. Supporting cells bearing microvilli are interposed between the receptor cells. The junction complex between the supporting cells and the receptor cells is composed of adherens and septate junctions, while between supporting cells only the adherens junctions are present. The static nerve arises from the lateral side of the cyst and contains axons in which parallel neurotubules and mitochondria are found. The axons arise directly from the base of the receptor cells without synapse. In the cyst lumen there are unattached statoconia. The statoconia have a plate-like or concentric membranous ring structure. Based on the morphology, the function of the statocyst in Biomphalaria is discussed.

Gao, Wenyuan↗
NASA NTRS1999

Large Diameter, Radiative Extinction Experiments with Decane Droplets in Microgravity

The extinction of a diffusion flame is of fundamental interest in combustion science. Linan, Law, and Chung and Law analytically and experimentally determined an extinction boundary in terms of droplet diameter and pressure for a single droplet due to Damkohler, or blowoff, extinction. More recently, other researchers demonstrated extinction due to finite rate kinetics in reduced gravity for free droplets of heptane. Chao modeled the effect of radiative heat loss on a quasi-steady spherically symmetric single droplet burning in the absence of buoyancy. They determined that for increasing droplet diameter, a second limit can be reached such that combustion is no longer possible. This second, larger droplet diameter limit arises due to radiative heat loss, which increases with increasing droplet and flame diameter. This increase in radiative heat loss arises due to an increase in the surface area of the flame. Recently, Marchese modeled fuel droplets with detailed chemistry and radiative effects, and compared the results to other work. The modeling also showed the importance of radiative loss and radiative extinction Experiments examined the behavior of a large droplet of decane burning in reduced gravity onboard the NASA Lewis DC-9 aircraft, but did not show a radiative extinction boundary due to g-jitter (Variations in gravitational level and direction) effects. Dietrich conducted experiments in the reduced gravity environment of the Space Shuttle. This work showed that the extinction diameter of methanol droplets increased when the initial diameter of the droplets was large (in this case, approximately 5 mm). Theoretical results agreed with these experimental results only when the theory included radiative effects . Radiative extinction was experimentally verified by Nayagam in a later Shuttle mission. The following work focuses on the combustion and extinction of a single fuel droplet. The goal is to experimentally determine a large droplet diameter limit that arises due to radiative heat loss from the flame to the surroundings.

Easton, John↗
NASA NTRS2002

Photonic Bandgaps in Photonic Molecules

This talk will focus on photonic bandgaps that arise due to nearly free photon and tight-binding effects in coupled microparticle and ring-resonator systems. The Mie formulation for homogeneous spheres is generalized to handle core/shell systems and multiple concentric layers in a manner that exploits an analogy with stratified planar systems, thereby allowing concentric multi-layered structures to be treated as photonic bandgap (PBG) materials. Representative results from a Mie code employing this analogy demonstrate that photonic bands arising from nearly free photon effects are easily observed in the backscattering, asymmetry parameter, and albedo for periodic quarter-wave concentric layers, though are not readily apparent in extinction spectra. Rather, the periodicity simply alters the scattering profile, enhancing the ratio of backscattering to forward scattering inside the bandgap, in direct analogy with planar quarter-wave multilayers. PBGs arising from tight-binding may also be observed when the layers (or rings) are designed such that the coupling between them is weak. We demonstrate that for a structure consisting of N coupled micro-resonators, the morphology dependent resonances split into N higher-Q modes, in direct analogy with other types of oscillators, and that this splitting ultimately results in PBGs which can lead to enhanced nonlinear optical effects.

Smith, David D.↗
NASA NTRS2003

Application of Core Dynamics Modeling to Core-Mantle Interactions

Observations have demonstrated that length of day (LOD) variation on decadal time scales results from exchange of axial angular momentum between the solid mantle and the core. There are in general four core-mantle interaction mechanisms that couple the core and the mantle. Of which, three have been suggested likely the dominant coupling mechanism for the decadal core-mantle angular momentum exchange, namely, gravitational core-mantle coupling arising from density anomalies in the mantle and in the core (including the inner core), the electromagnetic coupling arising from Lorentz force in the electrically conducting lower mantle (e.g. D-layer), and the topographic coupling arising from non-hydrostatic pressure acting on the core-mantle boundary (CMB) topography. In the past decades, most effort has been on estimating the coupling torques from surface geomagnetic observations (kinematic approach), which has provided insights on the core dynamical processes. In the meantime, it also creates questions and concerns on approximations in the studies that may invalidate the corresponding conclusions. The most serious problem is perhaps the approximations that are inconsistent with dynamical processes in the core, such as inconsistencies between the core surface flow beneath the CMB and the CMB topography, and that between the D-layer electric conductivity and the approximations on toroidal field at the CMB. These inconsistencies can only be addressed with numerical core dynamics modeling. In the past few years, we applied our MoSST (Modular, Scalable, Self-consistent and Three-dimensional) core dynamics model to study core-mantle interactions together with geodynamo simulation, aiming at assessing the effect of the dynamical inconsistencies in the kinematic studies on core-mantle coupling torques. We focus on topographic and electromagnetic core-mantle couplings and find that, for the topographic coupling, the consistency between the core flow and the CMB topography is critical for correct evaluation of the coupling torque.

Kuang, Weijia↗
NASA NTRS2003

Coherent Effects in Tiny Optics: Tunneling Through the Looking Glass

I will discuss two types of one-dimensional photonic bandgap (PBG) effects that can arise in systems of coupled spherical resonators: (1) nearly-free-photon Fabry-Perot photonic bands that arise in quarter-wave concentrically stratified spheres and, (2) tight- binding photonic bands that arise in weakly-coupled mutually-resonant spheres as a result of whispering-gallery mode splitting. These effects can be derived directly from Mie theory, in a more straightforward manner, by exploiting an analogy with stratified planar systems. For odd numbers of mutually-resonant lossless coupled ring resonators, the circulating intensity can increase exponentially with the number of resonators, which can potentially be exploited for the development of advanced sensors. For even numbers of resonators, mode splitting and classical destructive interference lead to a cancellation of absorption and slow light on-resonance, reminiscent of electromagnetic induced transparency. The analogy between these coherent photon trapping effects and population trapping in an atomic system will be explored.

Smith, David D.↗
NASA NTRS2003

Hot Gas in Planetary Nebulae

It was successfully obtained the FUSE spectra of all targets awarded. The analysis of the spectra has been a complex task due to the superposition of the P-Cygni profile from the wind of the central star and absorption components from low ionization and molecular species in the nebular shell. In six of the eight targets there are narrow O VI absorption components that may arise from the interface layer between the hot (l0(exp 6) K) interior gas and the surrounding warm (l0(exp 4) K) dense nebular shell. To better determine whether these narrow O VI absorption lines arise from the interface region we have obtained ground-based high-dispersion spectroscopic observations of the central star and nebula to pin-point the precise line-of-sight velocity of the nebular emission lines. The comparison between these optical spectra with the far-UV spectra obtained with FUSE is complete. The analysis shows that in most cases the narrow O VI absorption components have velocities slightly redshifted from the emission lines which arise from the approaching side of the nebular shell. Preliminary results have been published in two papers.

Gruendl, Robert A.↗
NASA NTRS1994

Skeletal muscle satellite cells

Evidence now suggests that satellite cells constitute a class of myogenic cells that differ distinctly from other embryonic myoblasts. Satellite cells arise from somites and first appear as a distinct myoblast type well before birth. Satellite cells from different muscles cannot be functionally distinguished from one another and are able to provide nuclei to all fibers without regard to phenotype. Thus, it is difficult to ascribe any significant function to establishing or stabilizing fiber type, even during regeneration. Within a muscle, satellite cells exhibit marked heterogeneity with respect to their proliferative behavior. The satellite cell population on a fiber can be partitioned into those that function as stem cells and those which are readily available for fusion. Recent studies have shown that the cells are not simply spindle shaped, but are very diverse in their morphology and have multiple branches emanating from the poles of the cells. This finding is consistent with other studies indicating that the cells have the capacity for extensive migration within, and perhaps between, muscles. Complexity of cell shape usually reflects increased cytoplasmic volume and organelles including a well developed Golgi, and is usually associated with growing postnatal muscle or muscles undergoing some form of induced adaptive change or repair. The appearance of activated satellite cells suggests some function of the cells in the adaptive process through elaboration and secretion of a product. Significant advances have been made in determining the potential secretion products that satellite cells make. The manner in which satellite cell proliferative and fusion behavior is controlled has also been studied. There seems to be little doubt that cellcell coupling is not how satellite cells and myofibers communicate. Rather satellite cell regulation is through a number of potential growth factors that arise from a number of sources. Critical to the understanding of this form of control is to determine which of the many growth factors that can alter satellite cell behavior in vitro are at work in vivo. Little work has been done to determine what controls are at work after a regeneration response has been initiated. It seems likely that, after injury, growth factors are liberated through proteolytic activity and initiate an activation process whereby cells enter into a proliferative phase. After myofibers are formed, it also seems likely that satellite cell behavior is regulated through diffusible factors arising from the fibers rather than continuous control by circulating factors.(ABSTRACT TRUNCATED AT 400 WORDS).

NASA Program Space Biology↗
NASA NTRS2010

Making Games Not Work: Paradoxes Embedded in Game-Based Training and Concepts for Overcoming Them

An interest in game-based training solutions is natural. All one has to do is watch someone fully engaged in a modern game to see the potential of harnessing that attention for training. However, the reality of game-based training has not fully satisfied these expectations. This paper explains two paradoxes that must be overcome for games to support training. These paradoxes are a result of the realities of the basic human condition clashing with the requirements of learning theory. 80th paradoxes arise from the concept of "engagement" that is central to games. The first comes from a more robust definition of engagement, which is the condition of Flow or Optimal Experience. Flow is the state game developers want to see in users. One aspect of Flow is loss of sense of self as the individual becomes immersed in the experience. The paradox arises because this loss of self directly contradicts the learning requirement of self-reflection. The second paradox comes from theories of play, which state in part that play requires a level of individual freedom. The contradiction arises when game-based play must be harnessed to an organizational training program or regimen. The paper will discuss these paradoxes in the context of an effort to design a game-based training modality to train combat medics and will close with a review of compensating strategies identified by the designers. The paper will provide information important to anyone interested in conceptualizing and designing game-based training.

Jones, Phillip N.↗
NASA NTRS2011

Compositional Impact of Io Volcanic Emissions on Jupiter's Magnetosphere and the Icy Galilean Moons

The magnetospheric ion population of Jupiter is dominated by the 1000 kg/s of iogenic material constantly ejected by IO volcanism as neutral gas (approx. 1 kg/s goes out as high speed dust grains), subsequent atmospheric losses to the IO torus, and radial transport of torus ions throughout the magnetosphere. As that magnetosphere is greatly distended in radial size by the iogenic plasma loading, so are surfaces of the other Galilean moons also significantly, and perhaps even dominantly, affected by iogenic plasma bombardment, e.g. at the level up to 0.2 kg/s heavy ions (mostly O and S) onto Europa as per local plasma ion measurements. In comparison, cometary impacts onto IO deliver about 0.02 kg/s of impact ejecta to Europa via ballistic transfer through the Jupiter system. The magnetosphere of this system operates as a powerful engine to produce and transport ions from the IO source to the surfaces of these other moons, and any future orbiter missions to these moons must account for surface distributions of the iogenic material and its chemical effects before real assessments can be made of sensible chemical materials otherwise arising from primordial formation and subsequent evolution of these moons. This is a fundamental problem of space weathering that must be addressed for all planetary bodies with thin atmospheres and direct surface exposure to their space plasma environments. Long-standing debates from Galileo Orbiter measurements about the origins of hydrate sulfates at Europa present examples of this problem, as to whether the sulfates arise from oceanic minerals or from iogenic sulfur chemistry. Any orbiter or landed mission to Europa for astrobiological investigations would further need to separate the potential chemical biosignatures of life or its precursors from the highly abundant background of iogenic material. Although no single ion carries a tag identifying it as of iogenic or other origin, the elemental abundance distributions of ions to be measured throughout the jovian magnetosphere and in the local moon environments can act as tracers if we know from direct measurements and models the distributions at the mostly likely sources, i.e. at IO. However, our knowledge of these abundances are very limited from earlier in-situ and remote measurements, mainly confined to major (S, O) and some minor (Na, K, Cl) species with abundances at or above a few percent relative to O. Future in-situ plasma measurements by the planned Jupiter Europa Orbiter and Jupiter Ganymede Orbiter missions should extend the abundance coverage to minor and even trace elemental species. For Europa astrobiological investigations it is also important to specify iogenic inputs and surface processing of isotopic species. We discuss the range of abundance distributions arising from models for IO hot volcanic emissions, and from the subsequent dynamics of ion injection, magnetospheric transport, and icy moon surface bombardment.

Cooper, John↗
NASA NTRS2014

Combined Uncertainty and A-Posteriori Error Bound Estimates for General CFD Calculations: Theory and Software Implementation

This workshop presentation discusses the design and implementation of numerical methods for the quantification of statistical uncertainty, including a-posteriori error bounds, for output quantities computed using CFD methods. Hydrodynamic realizations often contain numerical error arising from finite-dimensional approximation (e.g. numerical methods using grids, basis functions, particles) and statistical uncertainty arising from incomplete information and/or statistical characterization of model parameters and random fields. The first task at hand is to derive formal error bounds for statistics given realizations containing finite-dimensional numerical error [1]. The error in computed output statistics contains contributions from both realization error and the error resulting from the calculation of statistics integrals using a numerical method. A second task is to devise computable a-posteriori error bounds by numerically approximating all terms arising in the error bound estimates. For the same reason that CFD calculations including error bounds but omitting uncertainty modeling are only of limited value, CFD calculations including uncertainty modeling but omitting error bounds are only of limited value. To gain maximum value from CFD calculations, a general software package for uncertainty quantification with quantified error bounds has been developed at NASA. The package provides implementations for a suite of numerical methods used in uncertainty quantification: Dense tensorization basis methods [3] and a subscale recovery variant [1] for non-smooth data, Sparse tensorization methods[2] utilizing node-nested hierarchies, Sampling methods[4] for high-dimensional random variable spaces.

CFD↗