Search NASA⌕ Search

SEARCH · Search NASA

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Binder Jet Additive Manufacturing of Silicon Carbide Solar Reactor (CRADA Report)

Achieving high powder packing density is critical in binder jet additive manufacturing (BJAM), as it directly influences the final part density, mechanical properties, and sintering behavior. Multi-modal powder blends, which combine particles of different sizes, have been explored as a strategy to optimize packing efficiency and minimize defects. In this study, bimodal and trimodal powder blends were obtained by mixing silicon carbide powder in three different sizes. These results show that increased powder density is achievable with bimodal powder blends but is reduced in trimodal blends, and it was found that a 13% increase in the powder tap density was achieved using a bimodal blend of powder. The powder size distribution of the bimodal blend was measured at various stages during binder jet additive manufacturing and, no measurable powder separation occurred even after eight prints. Overall, this study shows limited advantage to trimodal powder blends but good promise for trimodal blends for increasing printed density while maintaining reusability in the binder jet process.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Process-Microstructure-Property Relationships in Low Heat Input Wire-Arc Additive Manufacturing (WAAM) of Ni-Based Superalloy Haynes 282

Conference presentation on WAAM process optimization on Ni-based superalloy Haynes® 282®. This alloy is targeted for advanced power generation systems for its superior high temperature mechanical properties. Wire-arc additive manufacturing (WAAM) offers attractive cost and materials savings with high deposition rates. Based on initial build process optimization, WAAM blocks were made, and screened for defects using high-throughput CT scanning. The microstructural evolution in arc energy range of 250-700 J/mm was characterized in the as-built and aged conditions, using electron microscopy. Results showed self-consistent microstructure across conditions, with grain size dependence on arc energy, MC and M6C carbides in as-built, and blocky grain boundary M23C6 in as-heat-treated condition. Further reductions in as-built porosity were explored through 20+ combinations of H2 and CO2 additions to shielding gas. Initial results show improved wetting behavior, and bead overlap with up to 1% H2 and up to 0.25% CO2. Combination of experimentally determined datasets provided comprehensive understanding of process-structure-property relationships in WAAM Haynes 282.

Haynes 282↗
DOE OSTI2025

A Novel Manufacturing Process of Lightweight Automotive Seats: Integration of Additive Manufacturing and Reinforced Polymer Composite

Lightweight automotive seats offer multiple benefits to original equipment manufacturers in terms of cost savings from various aspects, including less material usage, more integrated processes, and compliance with Corporate Average Fuel Economy Standards. Original equipment manufacturers have been focusing on innovative ways to produce light weight automotive seats. The commercially available automotive seats are currently made of multiple metal components combined through welding and fasteners. The use of additive manufacturing and composite structures is particularly useful for light weighting the automotive components. Additive manufacturing (AM) offers multiple advantages over traditional manufacturing processes such as freedom of design thereby enabling complex structural geometries, mass customization and waste minimization, and control over the fiber alignment through deposition in a predetermined pattern. Combining metal inserts with polymer composites through a novel manufacturing process allows design of lightweight and high-performance materials for automotive components.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Fabrication and Evaluation of Large Alumina Crucibles by Vat Photopolymerization Additive Manufacturing for High-Temperature Actinide Chemistry

Additive manufacturing (AM) offers opportunities to advance the design and function of ceramic tooling in high temperature actinide pyrochemistry. In technical ceramics such as alumina, conventional forming techniques often restrict design flexibility and can limit experimental progress. In this study, we investigate the use of vat photopolymerization (VP) with commercial resins to fabricate large-scale alumina crucibles, reaching dimensions up to 125 mm, which is significantly larger than typically reported for dense VP ceramics. Notably, these additively manufactured components are produced using consumer-grade hardware, which limits process control, but offers significant upside in scalability and accessibility. Using microscopy and X-ray computed tomography, the VP alumina parts have high bulk densities above 95%, but also the prevalence of AM-induced artifacts and surface defects. Mechanical testing showed these defects to significantly reduce flexural strength and compromise part reliability. Electrorefining trials under sustained exposure to molten salts and metals reveal mixed results, with the AM material exhibiting high chemical compatibility, but mechanical failures due to the reduced strength were prevalent. Our findings illustrate both the promise and current limitations of AM ceramics for actinide chemistry, and point toward future improvements in process optimization, design strategies, and part screening to enhance performance and reliability.

Materials science↗
DOE OSTI2024

Empirical Investigation of Properties for Additive Manufactured Aluminum Metal Matrix Composites

Laser additive manufacturing with mixed powders of aluminum alloy and silicon carbide (SiC) or boron carbide (B4C) is investigated in this experiment. With various mixing ratios of SiC/Al to form metal matrix composites (MMC), their mechanical and physical properties are empirically investigated. Parameters such as laser power, scan speed, scan pattern, and hatching space are optimized to obtain the highest density for each mixing ratio of SiC/Al. The mechanical and thermal properties are systematically investigated and compared with and without heat treatment. It shows that 2 wt% of SiC obtained the highest strength and Young’s modulus. Graded composite additive manufacturing (AM) of MMC is also fabricated and characterized. Various types of MMC devices, such as heat sink using graded SiC MMC and grid type three-dimensional (3D) neutron collimators using boron carbide (B4C), were also fabricated to demonstrate their feasibility for applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Microstructure Validation of Graph Theory Model-Derived Cooling Rates in the Wire Arc Additive Manufacturing of ER70S-6 Steel

Wire arc additive manufacturing (WAAM) enables high-rate fabrication of large metallic components, but spatial variations in thermal history can lead to microstructural heterogeneity that requires efficient process models to evaluate. This study evaluates whether cooling rates extracted from a graph theory model (GTM)-based thermal simulation are consistent with the microstructural evolution observed in an ER70S-6 WAAM wall. Thermal histories from the model were analyzed at selected build heights, and cooling rates were extracted from the final thermal excursion through the austenite phase field. Microstructures at corresponding locations were characterized using electron backscatter diffraction (EBSD) to quantify grain size distributions, and pearlite interlamellar spacing was used as an additional indicator of cooling behavior. The modeled cooling rates were highest near the substrate and generally decreased with build height, consistent with the observed reduction in the fine grain fraction and the progressive shift in the grain size distribution as build height increased. Pearlite spacing trends also supported the modeled cooling rate variation. These results indicate that GTM-derived thermal histories can be post-processed into metallurgically meaningful cooling rate estimates for WAAM steel builds and linked to dataset specific empirical grain size distribution relationships for process–thermal history–microstructure assessment.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Slicing Solutions for Wire Arc Additive Manufacturing

Both commercial and research applications of wire arc additive manufacturing (WAAM) have seen considerable growth in the additive manufacturing of metallic components. However, there remains a clear lack of a unified paradigm for toolpath generation when slicing parts for WAAM deposition. Existing toolpath generation options typically lack the appropriate features to account for all complexities of the WAAM process. This manuscript explores the key slicing challenges specific to toolpaths for WAAM geometry and pairs each consideration with multiple solutions to mitigate most negative effects on completed components. These challenges must be addressed to minimize voids, prevent bead collapse, and ensure deposited components accurately approximate the desired geometry. Slicing considerations are grouped into four general categories: geometric, process, thermal, and productivity. Geometric considerations are addressed with overhang compensation, corner-sharpening, and toolpath-smoothing features. Process considerations are addressed with start point configuration and controls for the bead lengths and end points. Thermal and productivity considerations are addressed with island optimization, multi-material printing, and connected insets. Finally, tools for the post-processing of generated G-code are explored. Overall, these solutions represent a critical set of slicing features used to improve generated toolpaths and the quality of the components deposited with those toolpaths.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Understanding the High-Temperature Deformation Behaviors in Additively Manufactured Al6061+TiC Composites via In Situ Neutron Diffraction

Aluminum matrix composites (AMCs) are designed to enhance the performance of conventional aluminum alloys for engineering applications at both room and elevated temperatures. However, the dynamic phase-specific deformation behavior and load-sharing mechanisms of AMCs at elevated temperatures have not been extensively studied and remain unclear. Here, in situ neutron diffraction experiments are employed to reveal the phase-specific structure evolution of additively manufactured Al6061+TiC composites under compressive loading at 250 °C. It is found that the addition of a small amount of nano-size TiC significantly alters the deformation behavior and increases the strength at 250 °C in comparison to the as-printed Al6061. Unlike the two-stage behavior observed in Al6061, the Al6061+TiC composites exhibit three stages during compression triggered by changes in the interphase stress states. Further analysis of Bragg peak intensity and broadening reveals that the presence of TiC alters the dislocation activity during deformation at 250 °C by influencing dislocation slip planes and promoting dislocation accumulation. These findings provide direct experimental observations of the phase-specific dynamic process in AMCs under deformation at an elevated temperature. The revealed mechanisms provide insights for the future design and optimization of high-performance AMCs.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Compressive Response and Energy Absorption of Additively Manufactured Elastomers with Varied Simple Cubic Architectures

Additive manufacturing, and particularly the vat photopolymerization process, enables the fabrication of complex geometries at high resolution and small length scales, making it well-suited for fabricating cellular structures (e.g., foams and lattices). Among these, elastomeric cellular structures are of growing interest due to their tunable compliance and energy dissipation. However, comprehensive data on the compressive behavior of these structures remains limited, especially for investigating the structure-property effects from changing the density and distribution of material within the cellular structure. This study explores how the mechanical response of polyurethane-based simple cubic structures changes when varying volume fraction, unit cell length, and unit cell patterning, which have not been systematically investigated previously in additively manufactured elastomers. Increasing volume fraction from 10% to 50% yielded significant changes in compressive stress–strain performance (decreasing strain at 0.5 MPa by 41.6% and increasing energy absorption density by 3962.5%). Although changing the unit cell length between 2.5 and 7 mm in ~30 mm parts did not result in statistically different stress–strain responses, modifying the configuration of struts of different thicknesses across designs with 30% volume fraction altered the stress–strain behavior (differences of 12.5% in strain at 0.5 MPa and 109.4% for energy absorption density). Power law relationships were developed to understand the interactions between volume fraction, unit cell length, and elastic modulus, and experimental data showed strong fits (R 2 > 0.91). These findings enhance the understanding of how multiple structural design aspects influence the performance of elastomeric cellular materials, providing a foundation for informing strategic design of tailorable materials for diverse mechanical applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Study of Helium Irradiation Effect on Al6061 Alloy Fabricated by Additive Friction Stir Deposition

Additive friction stir deposition (AFS-D) is considered a productive method of additive manufacturing (AM) due to its ability to produce dense mechanical parts at a faster deposition rate compared to other AM methods. Al6061 alloy finds extensive application in aerospace and nuclear engineering; nevertheless, exposure to radiation or high-energy particles over time tends to deteriorate their mechanical performance. However, the effect of radiation on the components manufactured using the AFS-D method is still unexamined. In this work, samples from the as-fabricated Al6061 alloy, by AFS-D, and the Al6061 feedstock rod were irradiated with He+ ions to 10 dpa at ambient temperature. The microstructural and mechanical changes induced by irradiation of He+ were examined using a scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDS), transmission electron microscopy (TEM), and nanoindentation. This study demonstrates that, at 10 dpa of irradiation damage, the feedstock Al6061 produced a bigger size of He bubbles than the AFS-D Al6061. Nanoindentation analysis revealed that both the feedstock Al6061 and AFS-D Al6061 samples have experienced radiation-induced hardening. These studies provide a valuable understanding of the microstructural and mechanical performance of AFS-D materials in radiation environments, offering essential data for the selection of materials and processing methods for potential application in aerospace and nuclear engineering.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Additive Manufacturing of Thermal Energy Storage Composites with Microencapsulated Phase Change Materials Supported in a Multi-Polymer Matrix

Advanced manufacturing techniques, such as additive manufacturing (AM), that can directly integrate phase change materials (PCMs) have garnered interest in recent years due to their potential for development of highly efficient thermal energy storage architectures. Complex, high surface area geometries embedded with PCMs that are only feasible with AM can improve thermal management with reduced material waste. Our work focuses on developing composite filaments with microencapsulated phase change materials (MEPCM) bound within a single or dual polymer matrix that can be processed through standard filament extruders and additively manufactured using off-the-shelf 3D printers. Polymer powders, rather than polymer pellets, were key to homogenously mixed filaments achieving high MEPCM loadings with no deterioration in thermal energy storage (TES) capability during extrusion. Composite filaments contain upwards of 60 wt% MEPCM and were printed without loss in feature resolution, print speed, or layer adhesion. Storage enthalpies of printed composites range from 100 - 130 kJ/kg, which were within 5% of the theoretical enthalpy based on weight fraction of MEPCM and maintained enthalpies within 1% over 500 thermal cycles. We can reliably manufacture low density, high surface area structures like 15% gyroid infill, along with dense, compact pucks at a 100% concentric infill. Prints were also scalable to a 900 cm3 honeycomb infill heat exchanger model that has an estimated energy storage capacity of 9 Wh.

3D printing↗
DOE OSTI2024

Corrosion Testing Of Additively Manufactured Stainless Steel 316H In Molten Salt Environments

The development of a new ASTM standard for evaluating the corrosion resistance of additive manufactured (AM) stainless steel (SS) 316H in chloride molten salts is critical for the use of these materials in extreme environments such as molten salt reactors (MSRs). This report pertains to a work package of the Advaned Materials and Manufacturing Technologies (AMMT) developing a systematic methodology to link changes in AM fabrication parameters, namely surface finishing, porosity, microstructure, and chemical heterogeneity, to corrosion performance in NaCl-MgCl2 salt, a proposed secondary coolant for MSRs. During Fiscal Year 2024, Idaho National Laboratory investigators in the AMMT program, utilized SS316H bars, fabricated with laser bed powder fusion at Los Alamos National Laboratory, to establish and optimize the workflow for evaluating these process-to-performance relationships. Standard practices for specimen preparation were established using these specimens, with particular focus on descaling and sectioning methods that align with ASTM guidelines. A comprehensive experimental design for static corrosion testing was developed, with pre- and post-exposure analysis utilizing optical microscopy and scanning electron microscopy. So far standard descaling techniques were optimized, one static corrosion test was conducted on the LANL AM SS316H specimens, and pre- and post-corrosion practices were established. In addition, the work package yielded a review paper on corrosion testing gaps for AM materials in nuclear applications and submitted a proposal for a rapid-turnaround experiment to the Nuclear Science User Facilities Program to investigate the combined effects of proton irradiation and corrosion on AM SS316H. This work package establishes a foundation for evaluating processing-to-performance relationships for AM SS316H in harsh conditions, contributing to the safe and efficient design of components for next-generation nuclear reactors. The creation of a standardized methodology and the generation of relevant publications and future research pathways represent significant strides towards integrating AM materials into critical applications where corrosion resistance is paramount.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Active Learning‐Driven Inkless Additive Nanomanufacturing for Printed Electronics

Inkless additive nanomanufacturing for printed electronics promises broad material and substrate versatility, yet the high-dimensional print parameter space makes tuning print parameters time-intensive. We present a Bayesian optimization study that constructs a digital twin from printed-silver data to benchmark surrogate models, acquisition functions, and batch sizes head-to-head to achieve user-specified target resistance. Tested surrogate models included Gaussian process, random forest, and Bayesian neural network surrogates with expected improvement and confidence bound acquisition functions. In total, we evaluate 48 unique model configurations alongside a random sampling baseline for comparison. For printed silver, the Bayesian neural network with a batch size of one achieved the lowest average cumulative regret, approximately four times more efficient on average than random sampling. To balance performance and substrate space, a random forest model with expected improvement and a batch size of four was chosen as the model for validation testing. Applying this chosen configuration to copper with an additional print parameter, the model achieved a resistance within 0.15 Ω of a 1 Ω target in fewer than 30 printed lines across five validation sets. Altogether, the workflow yields a tuned and validated model that efficiently guides experiments toward the target while simultaneously learning the parameter space.

Bevel, Colton [Auburn University, AL (United State↗
DOE OSTI2025

Measurement of $t\overline{t}$ production in association with additional b -jets in the eμ final state in proton–proton collisions at $\sqrt{s}$ = 13 TeV with the ATLAS detector

This paper presents measurements of top-antitop quark pair ($t\overline{t}$) production in association with additional b-jets. The analysis utilises 140 fb -1 of proton–proton collision data collected with the ATLAS detector at the Large Hadron Collider at a centre-of-mass energy of 13 TeV. Fiducial cross-sections are extracted in a final state featuring one electron and one muon, with at least three or four b-jets. Results are presented at the particle level for both integrated cross-sections and normalised differential cross-sections, as functions of global event properties, jet kinematics, and b-jet pair properties. Observable quantities characterising b-jets originating from the top quark decay and additional b-jets are also measured at the particle level, after correcting for detector effects. The measured integrated fiducial cross sections are consistent with $t\overline{t}$$b\overline{b}$ predictions from various next-to-leading-order matrix element calculations matched to a parton shower within the uncertainties of the predictions. State of-the-art theoretical predictions are compared with the differential measurements; none of them simultaneously describes all observables. Differences between any two predictions are smaller than the measurement uncertainties for most observables.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Additivity, Haag duality, and non-invertible symmetries

The algebraic approach to quantum field theory focuses on the properties of local algebras, whereas the study of (possibly non-invertible) global symmetries emphasizes global aspects of the theory and spacetime. We study connections between these two perspectives by examining how either of two core algebraic properties — “additivity” or “Haag duality” — is violated in a 1+1D CFT or lattice model restricted to the symmetric sector of a general global symmetry. For the Verlinde symmetry of a bosonic diagonal RCFT, we find that additivity is violated whenever the symmetry algebra contains an invertible element, while Haag duality is violated whenever it contains a non-invertible element. We find similar phenomena for the Kramers-Wannier and Rep(D 8 ) non-invertible symmetries on spin chains.

Discrete Symmetries↗
DOE OSTI2024

Additive friction stir deposition induced stress ripples in aluminum alloy

In additive manufacturing, modification of the viscosity of softened or molten metal plays a significant role in the development of mechanical properties distribution. Similar to soft polymers, molten or softened metal usually exhibits vastly different viscoelastic properties. During scratching tests, viscoelastic polymers undergo spatiotemporal stress development and relaxation, causing stress ripples to form on their surfaces. Here, it is observed that friction stir-based solid-state manufacturing can yield similar stress ripples on softened aluminum alloys due to the linear motion of the deposition tool. Softened aluminum alloys exhibit viscoelastic and viscoplastic responses similar to polymeric material during the solid-state deposition process. In the final product, residual stress ripples appear on the surface of the metal alloy due to periodic residual stress relaxation, leading to oscillatory behavior from the bulk mechanical properties of the material. The orientation of the in-built stress pattern formed in the bulk of the additively manufactured metal alloy underneath the visually evident onion ring-like surface pattern formation is diametrically in the opposite direction. The experimentally observed results are consistent with analytical calculation and numerical simulations in terms of behaviors.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Autonomous direct freeform fabrication strategy for multi-axis additive manufacturing

Multi-axis additive manufacturing (M-AM) enables precise material deposition along both planar and curved layers, eliminating the need for support structures through a continuous material deposition approach. In contrast to conventional 2-dimensional planar layers constrained to a fixed building orientation, the deposition on freeform layers demands the specification of guided curves to determine material deposition directions which are no longer to be fixed to a build direction. There are challenges that arise when fabricating components with multiple “build” directions, necessitating the decomposition of geometries and the specification of guided curves for the resulting volumes. Furthermore, multi-axis systems introduce heightened challenges due to an increased degree of freedom in motion. Consequently, the potential risks of collision between the deposited geometry and the motion platform become a notable concern. This research proposes a freeform layering algorithm to address the challenge of seamless transitions between planar and curved layers in the process planning of M-AM. The algorithm computes 3D “printable” layers by leveraging topological information derived from the geometry to be built and integrates collision-free manufacturability considerations into the computational process. These accumulated volumes serve as a “substrate” and support volumes for subsequent deposition, allowing later layers to be built without the need for additional support material. In conclusion, the proposed method successfully devises a freeform layering approach suitable for intricate models that demand substantial support, thus enabling the fabrication of diverse geometries in a manner previously unachievable.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Experimental Examination of Additively Manufactured Patterns on Structural Nuclear Materials for Digital Image Correlation Strain Measurements

Abstract Background There are a limited number of commercially available sensors for monitoring the deformation of materials in-situ during harsh environment applications, such as those found in the nuclear and aerospace industries. Such sensing devices, including weldable strain gauges, extensometers, and linear variable differential transformers, can be destructive to material surfaces being investigated and typically require relatively large surface areas to attach (> 10 mm in length). Digital image correlation (DIC) is a viable, non-contact alternative to in-situ strain deformation. However, it often requires implementing artificial patterns using splattering techniques, which are difficult to reproduce. Objective Additive manufacturing capabilities offer consistent patterns using programmable fabrication methods. Methods In this work, a variety of small-scale periodic patterns with different geometries were printed directly on structural nuclear materials (i.e., stainless steel and aluminum tensile specimens) using an aerosol jet printer (AJP). Unlike other additive manufacturing techniques, AJP offers the advantage of materials selection. DIC was used to track and correlate strain to alternative measurement methods during cyclic loading, and tensile tests (up to 1100 µɛ) at room temperature. Results The results confirmed AJP has better control of pattern parameters for small fields of view and facilitate the ability of DIC algorithms to adequately process patterns with periodicity. More specifically, the printed 100 μm spaced dot and 150 μm spaced line patterns provided accurate measurements with a maximum error of less than 2% and 4% on aluminum samples when compared to an extensometer and commercially available strain gauges. Conclusion Our results highlight a new pattern fabrication technique that is form factor friendly for digital image correlation in nuclear applications.

Novich, K. A. (ORCID:0000000204466022)↗