SEARCH · Search NASA

Results for “Aerodynamic Interference”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRSDate not supplied

Aerodynamic Optimization of Mach 0.745 Transonic Truss-Braced Wing Aircraft with Variable-Camber Continuous Trailing-Edge Flap

This paper presents an aerodynamic optimization study of the Mach 0.745 Transonic Truss-Braced Wing (TTBW) aircraft with Variable-Camber Continuous Trailing-Edge Flap (VC-CTEF). The VCCTEF is a novel wing shaping control concept to improve aircraft aerodynamic efficiency. Drag reduction studies are conducted for three different VCCTEF configurations with 6-, 10-, and 21-spanwise sections, respectively. A simple VCCTEF actuator weight model is proposed to account the weight penalty of the actuator in the design. A vortex-lattice model of the TTBW model is developed with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections for rapid aerodynamic performance evaluations. The VSPAERO model has been validated against wind tunnel test data. The optimization results show that the 21-spanwise sections VCCTEF has largest absolute drag coefficient reduction, however, the 6-spanwise sections VCCTEF provides a relatively better solution for drag reduction when the actuator weight penalty is considered. A high-fidelity CFD solver FUN3D is used to validate the VCCTEF optimization.

Aerodynamic Optimization↗

NASA NTRSDate not supplied

Aerodynamic Optimization of Mach 0.8 Transonic Truss-Braced Wing Aircraft using Variable Camber Continuous Trailing Edge Flap

This paper presents an aerodynamic optimization study of the Mach 0.8 Transonic Truss-Braced Wing (TTBW) aircraft with Variable Camber Continuous Trailing Edge Flap (VC-CTEF). The VCCTEF is a novel wing shaping control concept to improve aircraft aerodynamic efficiency. Drag reduction studies are conducted for two different VCCTEF configurations with 6- and 10-spanwise sections, respectively. A simple VCCTEF actuator weight model is used to account the weight penalty of the actuator in the design for the Mach 0.8 TTBW aircraft. A vortex-lattice model of the Mach 0.8 TTBW aircraft is developed with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections for rapid aerodynamic performance evaluations. The VSPAERO model has been validated against the wind tunnel test data. The optimization results show that the 6-spanwise sections VCCTEF provides a relatively better solution for drag reduction when the actuator weight penalty is considered. A high-fidelity CFD solver FUN3D is used to verify the VCCTEF optimization design.

Aerodynamic optimization↗

NASA NTRS2015

Fuselage-Induced Velocity Model for LRTA, RTA, and HART Fuselages

In order to make the aerodynamic fuselage-rotor interference effects available to comprehensive rotor codes, a simple analytical model of the fuselage-induced velocities within the volume of rotor blade operation above the fuselage is developed here for the following bodies used in wind tunnel experiments: the Large Rotor Test Apparatus (LRTA), the Rotor Test Apparatus (RTA), and the Higher Harmonic Control Aeroacoustic Rotor Test (HART).While the first two are used in the National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames, California, the third one is used by DLR in the large low-speed facility of the German-Dutch wind tunnel in the Netherlands. The fuselage-induced velocity model is based on parameter identification of isolated fuselage-induced velocity data (computed by means of computational fluid dynamics, CFD) and is intended to be generic enough to be used for real helicopter fuselages as well. The accuracies obtained in reproducing the CFD data show a remaining average error of less or equal 5 of the peak-to-peak induced velocity range, which is considered sufficient for comprehensive code analysis.

HART↗

NASA NTRS1980

Development of a metric half-span model for interference free testing

A metric half-span model has been developed which allows measurement of aerodynamic forces and moments without support interference or model distortion. This is accomplished by combining the best features of the conventional sting/balance and half-span splitter plate supports, For example, forces and moments are measured on one-half of a symmetrical model which is mechanically supported by a sting on the nonmetric half. Tests were performed in the Langley Unitary Plan wind tunnel over a Mach range of 1.60 to 2.70 and an angle-of-attack range of 04 deg to 20 deg. Preliminary results on concept evaluation, and effect of fuselage modification to house a conventional balance and sting are presented.

Corlett, W. A.↗

NASA NTRS1977

Introductory remarks

Suggested fluid mechanics research to be conducted in the National Transonic Facility include: wind tunnel calibration; flat plate skin friction, flow visualization and measurement techniques; leading edge separation; high angle of attack separation; shock-boundary layer interaction; submarine shapes; low speed studies of cylinder normal to flow; and wall interference effects. These theoretical aerodynamic investigations will provide empirical inputs or validation data for computational aerodynamics, and increase the usefulness of existing wind tunnels.

Gessow, A.↗

NASA NTRS1979

Characteristics of wing/body/tail configurations

Package of computer programs determine longitudinal aerodynamic characteristics of wing/body/tail combinations including effects of nonlinear aerodynamics of components and interference between components.

Dillenius, M. F. E.↗

NASA NTRS1984

High Reynolds number tests of the cast 10-2/DOA2 transonic airfoil at ambient and cryogenic temperature conditions

The transonic airfoil CAST 10-2/DOA2 was investigated in several major transonic wind tunnels at Reynolds numbers ranging from Re=1 million six hundred thousand to forty five million at ambient and cryogenic temperature conditions. The main objective was to study the degree and extent of the effects of Reynolds on both the airfoil aerodynamic characteristics and the interference effects of various model-wind-tunnel systems. the initial analysis of the 10-2 airfoil results revealed appreciable real Reynolds number effects on this airfoil and, moreover, showed that wall interference, can be significantly affected by changes in Reynolds number thus appearing as true Reynolds number effects.

Stanewsky, E.↗

NASA NTRS1989

High Reynolds number tests of the CAST-10-2/DOA 2 transonic airfoil at ambient and cryogenic temper ature conditions

The transonic airfoil CAST 10-2/DOA 2 was investigated in several major transonic wind tunnels at Reynolds numbers ranging from Re=1.3 x 10(exp 6) to 45 x 10(exp 6) at ambient and cryogenic temperature conditions. The main objective was to study the degree and extent of the effects of Reynolds number on both the airfoil aerodynamic characteristics and the interference effects of various model-wind-tunnel systems. The initial analysis of the CAST 10-2 airfoil results revealed appreciable real Reynolds number effects on this airfoil and showed that wall interference can be significantly affected by changes in Reynolds number thus appearing as true Reynolds number effects.

Stanewsky, E.↗

NASA NTRS1990

Finite element thermo-viscoplastic analysis of aerospace structures

The time-dependent thermo-viscoplastic response of aerospace structures subjected to intense aerothermal loads is predicted using the finite-element method. The finite-element analysis uses the Bodner-Partom unified viscoplastic constitutive relations to determine rate-dependent nonlinear material behavior. The methodology is verified by comparison with experimental data and other numerical results for a uniaxially-loaded bar. The method is then used (1) to predict the structural response of a rectangular plate subjected to line heating along a centerline, and (2) to predict the thermal-structural response of a convectively-cooled engine cowl leading edge subjected to aerodynamic shock-shock interference heating. Compared to linear elastic analysis, the viscoplastic analysis results in lower peak stresses and regions of plastic deformations.

Pandey, Ajay K.↗

NASA NTRS1990

Finite-element thermo-viscoplastic analysis of aerospace structures

Pandey, Ajay↗

NASA NTRS1972

Investigation of the McDonnell-Douglas orbiter and booster shuttle models in proximity at Mach numbers 2.0 to 6.0. Volume 7: Proximity data at Mach 4 and 6, interference free and launch vehicle data

Aerodynamic data obtained from a space shuttle abort stage separation wind tunnel test are presented. The .00556 scale models of the orbiter and booster configuration were tested in close proximity using dual balances during the time period of April 21 to April 27 1971. Data were obtained for both booster and orbiter over an angle of attack range from -10 to 10 deg for zero degree sideslip angle. The models were tested at several relative incidence angles and separation distances and power conditions. Plug nozzles utilizing air were used to simulate booster and orbiter plumes at various altitudes along a nominal ascent trajectory. Powered conditions were 100, 50, 25 and 0 percent of full power for the orbiter and 100, 50 and 0 percent of full power for the booster. Pitch control effectiveness data were obtained for both booster and orbiter with power on and off. In addition, launch vehicle data with and without booster power were obtained utilizing a single balance in the booster model. Data were also obtained with the booster canard off in close proximity and for the launch configuration.

Trimmer, L. L.↗

NASA NTRS1990

Grounding, bonding and shielding for safety and signal interference control

Aircraft models and other aerodynamic tests are conducted at the NASA Ames Research Center National Full Scale Aerodynamics Complex (NFAC). The models, tested in NFAC's wind tunnels, are sometimes heavily instrumented and are connected to a data acquisition system. Besides recording data for evaluation, certain critical information must be monitored to be sure the model is within operational limits. The signals for these parameters are for the most part low-level signals that require good instrumentation amplification. These amplifiers need to be grounded and shielded for common mode rejection and noise reduction. The instrumentation also needs to be grounded to prevent electrical shock hazards. The purpose of this paper is to present an understanding of the principles and purpose of grounding, bonding, and shielding.

Forsyth, T. J.↗

NASA NTRS1974

Aerodynamic investigations into various low speed L/D improvement devices on the 140A/B space shuttle orbiter configuration in the Rockwell International low speed wind tunnel (OA86)

Tests were conducted to investigate various base drag reduction techniques in an attempt to improve Orbiter lift-to-drag ratios and to calculate sting interference effects on the Orbiter aerodynamic characteristics. Test conditions and facilites, and model dimensional data are presented along with the data reduction guidelines and data set/run number collation used for the studies. Aerodynamic force and moment data and the results of stability and control tests are also given.

Mennell, R. C.↗

NASA NTRS1973

Analytical and experimental studies of shock interference heating in hypersonic flows

An analytical and experimental study is presented of the aerodynamic heating resulting from six types of shock interference patterns encountered in high speed flow. Centerline measurements of pressure and heat transfer distributions on basic bodies were obtained in four wind tunnels for Mach numbers from 6 to 20, specific heat ratios from 1.27 to 1.67, and free stream Reynolds numbers from 3 million to 25.6 million per meter. Peak heating and peak pressures up to 17 and 7.5 times stagnation values, respectively, were measured. In general, results obtained from semiempirical methods developed for each of the six types of interference agreed with the experimental peaks.

Keyes, J. W.↗

NASA NTRS1938

Interference of Wing and Fuselage from Tests of the 18 Combinations in the N.A.C.A. Variable-density Tunnel - Combination with Split Flaps

As part of the wing-fuselage interference investigation in progress in the N.A.C.A. variable density wind tunnel, the effects of various split-flap arrangements applied to wing-fuselage combinations were determined. Split flaps were found to exert their influence independently of the interference, and their effects on the aerodynamic characteristics of rectangular-airfoil combinations appeared to be more or less proportional to their exposed span lengths. The interference, moreover, showed the same character with the split flaps as without them.

Sherman, Albert↗

NASA NTRS1979

Test technique development in interference free testing, flow visualization, and remote control model technology at Langley's Unitary Plan wind tunnel

A metric half-span model is considered as a means of mechanical support for a wind-tunnel model which allows measurement of aerodynamic forces and moments without support interference or model distortion. This technique can be applied to interference-free propulsion models. The vapor screen method of flow visualization at supersonic Mach numbers is discussed. The use of smoke instead of water vapor as a medium to produce the screen is outlined. Vapor screen data are being used in the development of analytical vortex tracking programs. Test results for a remote control model system are evaluated. Detailed control effectiveness and cross-coupling data were obtained with a single run. For the afterbody tail configuration, tested control boundaries at several roll orientations were established utilizing the facility's on-line capability to 'fly' the model in the wind tunnel.

Corlett, W. A.↗

NASA NTRS2016

Wind Tunnel Interference Effects on Tilt Rotor Testing Using Computational Fluid Dynamics

Experimental techniques to measure rotorcraft aerodynamic performance are widely used. However, most of them are either unable to capture interference effects from bodies, or require an extremely large computational budget. The objective of the present research is to develop an XV-15 Tiltrotor Research Aircraft rotor model for investigation of wind tunnel wall interference using a novel Computational Fluid Dynamics (CFD) solver for rotorcraft, RotCFD. In RotCFD, a mid-fidelity Unsteady Reynolds Averaged Navier-Stokes (URANS) solver is used with an incompressible flow model and a realizable k-ε turbulence model. The rotor is, however, not modeled using a computationally expensive, unsteady viscous body-fitted grid, but is instead modeled using a blade-element model (BEM) with a momentum source approach. Various flight modes of the XV-15 isolated rotor, including hover, tilt, and airplane mode, have been simulated and correlated to existing experimental and theoretical data. The rotor model is subsequently used for wind tunnel wall interference simulations in the National Full-Scale Aerodynamics Complex (NFAC) at Ames Research Center in California. The results from the validation of the isolated rotor performance showed good correlation with experimental and theoretical data. The results were on par with known theoretical analyses. In RotCFD the setup, grid generation, and running of cases is faster than many CFD codes, which makes it a useful engineering tool. Performance predictions need not be as accurate as high-fidelity CFD codes, as long as wall effects can be properly simulated. For both test sections of the NFAC wall, interference was examined by simulating the XV-15 rotor in the test section of the wind tunnel and with an identical grid but extended boundaries in free field. Both cases were also examined with an isolated rotor or with the rotor mounted on the modeled geometry of the Tiltrotor Test Rig (TTR). A "quasi linear trim" was used to trim the thrust for the rotor to compare the power as a unique variable. Power differences between free field and wind tunnel cases were found from -7 to 0 percent in the 80- by 120-Foot Wind Tunnel and -1.6 to 4.8 percent in the 40- by 80-Foot Wind Tunnel, depending on the TTR orientation, tunnel velocity, and blade setting. The TTR will be used in 2016 to test the Bell 609 rotor in a similar fashion to the research in this report.

CFD↗

NASA NTRS2015

Wind Tunnel Interference Effects on Tilt Rotor Testing Using Computational Fluid Dynamics

Experimental techniques to measure rotorcraft aerodynamic performance are widely used. However, most of them are either unable to capture interference effects from bodies, or require an extremely large computational budget. The objective of the present research is to develop an XV-15 Tilt Rotor Research Aircraft rotor model for investigation of wind tunnel wall interference using a novel Computational Fluid Dynamics (CFD) solver for rotorcraft, RotCFD. In RotCFD, a mid-fidelity URANS solver is used with an incompressible flow model and a realizable k-ε turbulence model. The rotor is, however, not modeled using a computationally expensive, unsteady viscous body-fitted grid, but is instead modeled using a blade element model with a momentum source approach. Various flight modes of the XV-15 isolated rotor, including hover, tilt and airplane mode, have been simulated and correlated to existing experimental and theoretical data. The rotor model is subsequently used for wind tunnel wall interference simulations in the National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames Research Center in California. The results from the validation of the isolated rotor performance showed good correlation with experimental and theoretical data. The results were on par with known theoretical analyses. In RotCFD the setup, grid generation and running of cases is faster than many CFD codes, which makes it a useful engineering tool. Performance predictions need not be as accurate as high-fidelity CFD codes, as long as wall effects can be properly simulated. For both test sections of the NFAC wall interference was examined by simulating the XV-15 rotor in the test section of the wind tunnel and with an identical grid but extended boundaries in free field. Both cases were also examined with an isolated rotor or with the rotor mounted on the modeled geometry of the Tiltrotor Test Rig (TTR). A 'quasi linear trim' was used to trim the thrust for the rotor to compare the power as a unique variable. Power differences between free field and wind tunnel cases were found from -7 % to 0 % in the 80- by 120-Foot Wind Tunnel test section and -1.6 % to 4.8 % in the 40- by 80-Foot Wind Tunnel, depending on the TTR orientation, tunnel velocity and blade setting. The TTR will be used in 2016 to test the Bell 609 rotor in a similar fashion to the research in this report.

CFD↗