SEARCH · Search NASA

Results for “Aging resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Evidence that Surface-Segregated Sr Phases Can Be Removed in LSCF via Ceria Pre-Infiltration, Are Less Apt to Form in SSC

Here Ce 0.9 Gd 0.1 O 1.95−x (GDC) pre-infiltration was performed on 12 vol.% La 0.6 Sr 0.4 Co 0.8 Fe 0.2 O 3−x (LSCF) or Sm 0.5 Sr 0.5 CoO 3−x (SSC) infiltrated GDC Solid Oxide Fuel Cell cathodes. The addition of 7.5 vol.% of ∼40 nm diameter GDC nanoparticles into a ∼30 μ m thick porous scaffold of partially-sintered, sub-micron GDC particles before LSCF infiltration 1) lowered the temperature needed to produce a LSCF-GDC polarization resistance ( R P ) of 0.1 Ohm*cm 2 by ∼50 °C, and 2) reduced the amount of 500 h, 650 °C open-circuit LSCF-GDC R P degradation from ∼37% to ∼6%. In contrast, GDC pre-infiltration had no effect on the initial SSC-GDC R P or the 19% in R P degradation observed during 500 h of 650 °C open-circuit aging. X-Ray Photoelectron Spectroscopy showed that GDC pre-infiltration lowered the concentration of strontium species on the surface of the initial and 650 °C-aged LSCF-GDC, but had no effect on the initial or aged SSC-GDC Sr concentrations. Similarly, Electrochemical Impedance Spectroscopy showed that for both the initial and aged LSCF-GDC, GDC pre-infiltration improved oxygen exchange at the infiltrate-backbone and infiltrate-gas interfaces, but had no effect on the SSC-GDC. Hence, GDC pre-infiltration was concluded to improve LSCF-GDC performance and durability by scavenging exsolved Sr-rich secondary phases that form on the interfaces of LSCF, but not SSC.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Multi-Gas Sensors for Enhanced Reliability of SOFC Operation

GE Research, in partnership with SUNY Polytechnic Institute (SUNY Poly), designed, built, and tested gas sensors for in situ monitoring of H 2 and CO anode tail gases produced with on-site steam reforming in solid oxide fuel cell (SOFC) systems. The knowledge of the H 2 /CO ratio of these anode tail gases should allow accurate determination and control of the efficiency of the reforming process in the SOFC system and should deliver a lower operating cost for SOFC customers. The project objectives were to achieve multi-gas monitoring capability with a single multivariable sensor, and to sustain this performance in the presence of gaseous interferences and a potential poison for the sensor. The duration of the project was 24 months with the project structure that included three technical tasks such as (1) development of design rules of photonic nanostructures for H 2 and CO gas detection, (2) laboratory validation of photonic nanostructures for selective H 2 and CO gas detection, and (3) validation of photonic nanostructures for initial stability and poison-resistance against H 2 S. To build multivariable sensors for selective H 2 and CO gas detection in the presence of interferences, we expanded our earlier knowledge of multi-gas sensors into new fabrication and functionalization methodologies as well as into new methodologies for the spectral data analysis of multi-gas responses. We have advanced our design rules of the three-dimensional (3D) photonic nanostructures that allowed detection of H 2 and CO at high temperatures as individual gases and as their mixtures and rejection of interferences such as CO 2 , H 2 O, CH 4 , and other hydrocarbons for SOFC applications. Our advanced design rules should be attractive for building the new generation of cost-effective industrial sensors. Stability and poison resistance of our 3D photonic nanostructures was tested in the laboratory conditions. While initially we utilized conventional machine learning data analysis tools, we have found that they were unable to correct for the sensor drift. Thus, we have implemented new methods of machine learning for the analysis of our spectral data. These learnings pave the way to move the future studies into advanced testing of effects of interferences, aging and field tests. In future, our work will continue to advance our sensing designs to operate in conditions with known and unknown interferences by implementing nanostructures with enhanced spectral diversity of responses to gaseous species of interest and interferences. Our systematic reduction of technical risks in this completed project and in future studies will ensure transition of this sensing technology to commercialization.

03 NATURAL GAS↗

DOE OSTI2026

Long‐term growth and persistence of granitic inselbergs in a semi‐arid cratonic landscape

Granitic inselbergs are enduring landforms that punctuate planation surfaces in tectonically stable settings, yet the mechanisms and timescales of their persistence remain debated. Here, in this study, we present a multinuclide cosmogenic dataset ( 10 Be, 26 Al and 21 Ne) from bedrock, fluvial sediments and planation surfaces in the semi-arid Central Ceará Domain, north-eastern Brazil, to quantify denudation rates and reconstruct the long-term dynamics of residual relief formation. This triple-nuclide approach enables independent validation of denudation contrasts and long-term exposure histories, providing quantitative constraints on inselberg evolution that a single-nuclide approach could not resolve. Bedrock denudation rates (1–4 m Myr −1 ) are systematically lower than basin-wide rates (8–14 m Myr −1 ), revealing a regional pattern of vertical differential denudation. When combined with summit elevations and surface exposure ages of up to 5 Myr, these contrasts suggest that cumulative relief growth has been operating over timescales of tens of millions of years (1–57 Myr). Morphological and structural observations further indicate localized mass wasting and heterogeneous erosion styles, modulated by rock fabric and joint density. Cosmogenic nuclide inventories in detrital sediments reveal partial reworking from older sediment stocks, including surface pebbles with exposure ages up to 5 Myr, which record multistage of burial and re-exposure histories and reflect episodic remobilization in low-connectivity, semi-arid catchments. Rather than static relicts of ancient surfaces, inselbergs in this cratonic setting emerge as dynamic landforms actively sustained by slow but persistent differential denudation. These results provide new constraints on long-term cratonic landscape evolution and underscore the interplay between lithological resistance, structural inheritance and sediment transfer processes in sustaining topographic relief. They also call for a critical reassessment of classical inselberg models, suggesting that hybrid mechanisms, rather than single-process paradigms, more accurately capture the complexity of residual landform development in cratonic interiors.

Cosmogenic nuclides↗

DOE OSTI2021

Assessment of Aging Degradation Mechanisms of Alloy 709 for Sodium Fast Reactors

This project was initiated in October 2015 to investigate the creep and creep-fatigue behavior of Alloy 709 for structural components in Gen IV sodium cooled fast spectrum reactors. The goal of this project is to develop an understanding of the mechanisms responsible for the behavior of austenitic stainless steel alloy 709 under accelerated testing conditions to confidently predict long term creep and creep-fatigue behavior at the times (500,000 hours) and temperatures (550°C) of interest for fast reactor structural applications. Alloy 709 has exhibited significantly better creep resistance than Alloy 316H, which is currently specified in design of fast reactor structural components. However, the alloy has not been code qualified for elevated temperature nuclear design. The elevated temperature microstructure stability and creep and creep-fatigue behavior need to be better understood so service life can be accurately predicted. Alloy 709 was developed for fossil boiler applications, which operate at a higher temperature than the nuclear components. Thus, there is a strong need to characterize its creep and creep-fatigue behavior at these lower temperatures and corresponding longer service lifetimes. The overall objective of this project is to develop sufficient understanding of the mechanisms responsible for behavior of Alloy 709 under accelerated testing conditions to confidently predict long term creep and creep-fatigue behavior at the times (500,000 hours) and temperatures (550°C) of interest for fast reactor structural applications. The following report summarizes the findings of the creep-fatigue and creep behavior with respect to the research questions identified during the course of the project. Additionally, the training and professional development that occurred through the project and the products resulting from the project are summarized.

36 MATERIALS SCIENCE↗

DOE OSTI2021

The subsurface structure of abraded Al–Zn–Mg–Cu alloy

Surface abrasion has been shown to introduce heavy shear stress and produce a few hundred nanometers thick altered surface layer (ASL) on Al alloys. Such ASLs exhibit microstructural changes at room temperature and different corrosion resistance than the underlying substrate. Here, we report how sample dimensions and temperature affect the deformed subsurface microstructure evolution on an abraded Al–Zn–Mg–Cu alloy using transmission electron microscopy (TEM) and atom probe tomography. The ASL microstructure evolves differently in the bulk sample than in the thin TEM specimen. In the freshly abraded ASL, the original η'/η precipitates and grain boundaries were deformed toward the abrasion direction. After 7-day natural aging of the freshly abraded bulk sample, well-defined subgrains formed locally in the ASL, and unusual Al 2 Cu (θ) and Mg x Zn y phases precipitated at the subgrain boundaries. However, during natural aging of this TEM specimen taken from the abraded and aged bulk samples, much faster changes occurred, including the continued formation of subgrains and θ particles in the entire ASL, and the diffusion of Zn atoms out of Mg x Zn y particles to form a Zn particle. On the other hand, no obvious microstructural changes occurred in the ASL during 3-month natural aging of the TEM specimen immediately taken from the freshly abraded sample. Finally, this work advances the understanding of how Al alloy microstructures respond during and following any shear deformation, and complex and unexpected effects of sample dimensions on the behavior.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Effect of Zr and Sc additions on coarsening- and creep resistance of AlSi10Mg fabricated by laser powder bed fusion

Microstructure and creep properties are studied in a eutectic AlSi10Mg alloy modified with Zr and Sc additions (Al-9.8Si-0.32Mg-0.70Zr-0.23Sc, wt%) manufactured through laser powder-bed fusion (L-PBF). Three types of Zr/Sc-bearing powders - elemental, master-alloy, and pre-alloyed - are employed in the fabrication process, with the pre-alloyed powders providing the highest incorporation of Zr and Sc in the Al matrix. Here, the as-printed alloy exhibits a fine cellular Al-Si eutectic structure which fragments and coarsens into micron-sized Si particles during aging at 300 ºC, leading to a steady drop in alloy microhardness between 0.1 and 1000 h. Coarsening of the eutectic Si phase during aging is not measurably affected by Zr and Sc in solid solution, which precipitate during aging and increases strength, compensating weakening from Si coarsening between 1 and 200 h at 300 ºC. Atom-probe analysis in the peak-aged condition (96 h/300 °C) confirms the presence of Al 3 (Sc,Zr) secondary nano-precipitates with an average radius of 1.0 nm and some Si solubility. Micron-sized grains are present throughout the alloy, with ultra-fine-grained regions at the melt pool boundaries, neither of which coarsen during long-term aging at 300 ºC. Under creep conditions at 300 °C, the Zr/Sc-bearing alloy with Al 3 (Sc,Zr) nano-precipitates exhibits power-law behavior, with a high apparent stress exponent (n a = 9) and a high threshold stress (σ th = 43 MPa), exhibiting nearly double the strength of a Zr/Sc-free AlSi10Mg control alloy (σ th = 22 MPa).

36 MATERIALS SCIENCE↗

DOE OSTI2023

Review of HAYNES® 282® alloy for supercritical CO2 structural applications

In this paper, HAYNES® 282® alloy (282® alloy) properties, microstructure, high temperature oxidation resistance, weldability, and American Society of Mechanical Engineers (ASME) code case highlights are reviewed. The long term performance of high temperature, high strength, creep resistant alloys is critical to the success of supercritical carbon dioxide equipment. Several modern power generation technologies require alloys that can operate continuously at or above 700oC. 282® alloy is a precipitation strengthened nickel based super alloy that meets these requirements. The results of 282® alloy research reviewed in this paper include longterm cyclic oxidation behavior in air and sCO2, independent research and validation of 100k hour creep life, and successful welding of the alloy in the age hardened condition. The latter is critical for joining of hardened components (flanges, piping, heat exchanger internal, etc.) and field repair. Several highlights from the code case for this ASMEapproved material are also presented.

Tossey, Brett↗

DOE OSTI2021

The Application of Differential Scanning Calorimetry to Investigate Precipitation Behavior in Nickel-Base Superalloys Under Continuous Cooling and Heating Conditions

In this study, a suite of experimental tools and fast-acting, numerical-simulation techniques was used to quantify the precipitation behavior of three nickel-base superalloys: IN-100, LSHR, and 718. Experimental methods comprised differential scanning calorimetry (DSC) to establish the specific heat as a function of temperature and selected direct-resistance heating trials (using a Gleeble ® machine) to obtain samples for microstructural analysis. For the DSC experiments, each alloy was cooled at a prescribed constant rate (between 5 and 20 K/min) after an initial soak/equilibration in the high-temperature, single-phase (supersolvus) temperature regime. On-heating DSC trials beginning at ambient temperature were also performed on alloy 718 in three different starting conditions: super- δ -solvus solution treated and water quenched (denoted as ST), solution treated and aged (STA), and solution treated and overaged (STOA). DSC results, revealing the thermal signatures associated with the kinetics of precipitation of γ ' (IN-100, LSHR) or γ ' and γ " (718), were interpreted using a previously-developed fast-acting routine that treats concurrent nucleation, growth, coarsening, and dissolution. For these simulations, special attention was paid to various thermo-kinetic input parameters including equilibrium solvus-approach curves, bulk free energies of transformation, matrix-precipitate interface energies, and effective diffusivities. For the γ - γ ' superalloys (IN-100 and LSHR), estimates of precipitate volume fraction as a function of temperature from the specific-heat data revealed semi-quantitative agreement with simulation predictions. For the γ - γ '- γ " superalloy (718), simulation predictions of precipitate volume fractions were converted to specific heat as a function of temperature and showed semi-quantitative agreement with the direct measurements.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Identifying multiple synergistic factors on the susceptibility to stress relaxation cracking in variously heat-treated weldments

The 347H austenitic stainless steel has been widely used for pressure vessels and pipeline (PVP) applications due to its excellent creep and corrosion resistance, which fit ideally to the harsh conditions in petrochemical industries, fossil fuel or nuclear power plants, and modern energy storages. However, a failure mode has been commonly observed with cracks emerging at the heat affected zone (HAZ) of weldments during post-weld heat treatment (PWHT) or under intermediate to high temperature service conditions. This phenomenon is termed as Stress Relaxation Cracking (SRC) since the purpose of PWHT is to relieve the welding-induced residual stress fields, or as Stress Age Cracking (SAC) if failure happens during service. A leading literature explanation of this failure suggests that the residual stress relaxation and the precipitation dissolution and/or re-precipitation occur in the same temperature range, which can lead to locally high strains and thus to crack at the grain boundaries. Since in situ spatial measurements of residual stress fields, microstructural evolution, and failure processes are nearly infeasible, this work recourses to a micromechanical finite element framework that models the high temperature failure as the nucleation and growth of grain boundary cavities, whereas various parameters such as thermomechanical loading history and its evolution, the competition of grain-interior dislocation creep and grain-boundary diffusion in failure lifetime, and microstructural heterogeneities (such as the precipitate free zone near grain boundaries) can be quantitatively incorporated. It can be concluded from these microstructure-explicit simulations that an accurate knowledge of residual stress evolution and a carefully calibrated set of material constitutive parameters are the essential prerequisites for lifetime predictions. The understanding of individual governing factors also leads to a mechanistic interpretation of the observed SRC susceptibility C-curves. In conclusion, these results suggest that the criticality of residual stress evolution, but not the precipitation-induced local strains, be the leading factor for SRC.

347H stainless steel weldments↗

DOE OSTI2024

Hardenability and microstructural evolution of a precipitation strengthened Ni 50 Ti 21 Hf 25 Al 4 alloy

NiTi-based quaternary alloys are used in a variety of mechanical components, such as bearings, actuators, and dampers, owing to their good hardenability, wear resistance, and corrosion resistance. Additionally, one of the most notable characteristics of NiTi-based alloys is their shape memory effect and pseudoelastic properties. Connecting the macroscopic processing parameters employed in the design of new intermetallic alloys to the nanoscale structural characteristics dictating their behavior is crucial for improving their mechanical properties and expanding the spectrum of potential applications. Here, in this work, an arc melted Ni 50 Ti 21 Hf 25 Al 4 (at%) alloy was solution treated at 1050 °C followed by quenching and aging at 600 °C to investigate the effect of aging time on the microstructure and mechanical properties. Two types of nano-sized precipitates were observed and determined as face-centered orthorhombic H-phase (TiHf)Ni and L2 1 Heusler precipitates Ni 2 TiAl. The morphology and orientation of the H-phase were investigated using scanning and transmission electron microscopy (SEM and TEM), elucidating the coarsening kinetics and strengthening contribution of that phase to the intermetallic mechanical behavior. Following coarsening, the presence of Heusler nanoprecipitates was detected under overaged conditions through TEM imaging and nanobeam electron diffraction patterns. A peak hardness condition of 756 HV was achieved after 70 h of aging, indicating that the co-precipitation of H-phase and Heusler precipitates through a well-designed aging treatment can lead to optimal mechanical performance, thus elevating the alloy’s potential as a viable material for industrial applications.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Transparent and Conductive Inorganic/Polymer‐Composite Encapsulants for Long‐Term Perovskite Solar Cells Operation

An innovative inorganic/polymer-composite encapsulation scheme comprising a polymer-based transparent conductive composite (TCC) coupled with a transparent conductive oxide is introduced to extend the lifetime of moisture-sensitive devices such as perovskite solar cells (PSC). The TCC comprises conductive silver-coated polymethyl methacrylate (Ag-PMMA) microsphere fillers protruding from a transparent non-conductive polymer matrix. TCC samples (5% Ag-PMMA by area) demonstrate high optical transparencies (%T approx. 85% in the 370–1200 nm region), low out-of-plane electrical resistivities (R < 0.2 Ω cm 2 ), and equilibrium permeabilities of less than 1 g mm/m 2 /day, all of which are well-maintained after 1,000 hours of environmental exposure. In practice, the TCC is employed between two indium zinc oxide (IZO) thin films, with the in-plane conductivity of IZO and the out-of-plane conductivity of TCC working collectively to function as a single encapsulating electrode. This encapsulation scheme is exemplified by benchmarking performances of PSCs subjected to accelerated aging conditions of quasi-maximum power point tracking under light soaking in air at 50 °C, 40% R.H. to 60% R.H. Notable improvements in operational lifetimes are observed, with a champion encapsulated PSC maintaining over 90% of its initial efficiency of 21.65% for up to 1,430 hours, compare to less than 300 hours for an unencapsulated control.

14 SOLAR ENERGY↗

DOE OSTI2023

Laser additive manufacturing for infrastructure repair: A case study of a deteriorated steel bridge beam

As our transportation infrastructure ages, its deterioration is becoming a growing concern. Rapid and effective methods for repair can reduce the need for time-and cost-intensive replacement of structures such as roadway bridges. In this work, laser-based additive manufacturing (AM) was developed for the re-pair of damaged beams in steel bridges. A corroded structural beam of low-carbon A36 steel was selected for this case study and 316L stainless steel was used for repair due to its excellent mechanical properties and corrosion resistance. Simulated repair experiments were performed on specimens extracted from the beam, and prepared with various groove shapes (Rectangular, Trapezoidal, and U-shaped). More in-depth parametric and microstructural studies were carried out with a series of U-shaped specimens repaired with the linear laser input energy varied from 19.5 to 30.0 J mm -1 . The tensile properties of the repaired specimens and interface structures were also investigated in detail. It was found that the repaired specimens had a slightly higher tensile strength despite a reduction in tensile elongation compared to the A36 steel base metal. The influence of interfacial microstructure and heterogeneity on the mechanical proper-ties of the repaired specimens was discussed. Furthermore, our work suggests the promising potential to employ AM for structural repair and provides fundamental insights into processing-structure-property relationships in laser AM-repaired materials.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Microstructure and strengthening of Al-6Ce-3Ni-0.7Fe (wt%) alloy manufactured by laser powder-bed fusion

In this study, an Al-6Ce-3Ni-0.7Fe (wt%) alloy was fabricated via laser powder-bed fusion and its microstructure, thermal stability, tensile properties, and creep properties are investigated for two rapid-solidification rates with different eutectic spacings. For both faster- and slower-cooled states, the as-fabricated alloy mostly shows elongated grains with very fine eutectic networks (~40 nm lamellar width) comprising a high-volume fraction (~18 %) of intermetallic phases. Faster-cooled samples, however, display a less continuous eutectic network with finer spacing (~100 nm), leading to higher Orowan strengthening and therefore superior microhardness and yield stress up to ~350 °C. Upon aging (300 - 450 °C), micron-size Al 9 (Ni,Fe) 2 needle-like precipitates form within grains, and the Al 11 Ce 3 eutectic network spheroidizes, while retaining a submicron width and spacing, resulting in 33–37 % drop in microhardness after 144 h aging at 400 °C. Limited tensile ductility (~6 %) and creep ductility (~1-2 %) are measured for both faster- and slower-cooled alloys due to an inhomogeneous microstructure, where cavitation preferentially initiates at melt-pool boundaries, precipitate-free zones, and/or denuded zones, eventually leading to local fracture. Denuded zones, induced by stress, form due to diffusional flow with stress-dependent orientations, and are identified as microstructurally weak regions leading to strain localization. The present alloy does not show a significant difference in 300 °C creep resistance between: (i) tensile and compressive loading, (ii) faster- and slower-cooled samples, and (iii) continuous and spheroidized eutectics. Creep resistance at 300 °C is comparable to that of a Ce-richer Al-10.5Ce-3.1Ni-1.2Mn (wt%) alloy, despite the formation of denuded zones and needle-like Al 9 (Ni,Fe) 2 precipitates.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Dual-precipitates enhance fatigue resistance in an additively manufactured high-entropy alloy

To accomplish the intense desire of high-strength materials for enhanced energy-efficiency, recent research applies a combined strategy of additive-manufacturing and precipitation-strengthening in high entropy alloys. In a context, Al 0.2 Co 1.5 CrFeNi 1.5 Ti 0.3 nanoprecipitation-strengthened system was developed, demonstrating very convincing strength and toughness. Moreover, additive-manufacturing facilitated additional strength by well-decorated cell-boundaries with blocky L2 1 precipitates and homogeneously distributed L1 2 precipitates. However, fatigue research of this alloy remained unexplored despite being the main precursor for structural applications. In this study low-cycle fatigue behavior of this alloy in both as-built and precipitation-strengthened (aged) conditions has been explored, combined with in-situ neutron diffraction investigation. Findings revealed a substantial cyclic-stress profile and a notable fatigue-life below ±0.50% strain-amplitude, exceeding 10 5 cycles at ±0.30% strain-amplitude. These demonstrate the potential to carry higher payloads with marked engineering-reliability. Residual-stress estimation revealed strain-compatibility between the matrix and L1 2 precipitate, indicating a crack-initiation immune interface. A comparative examination of dislocation character revealed shifting towards pure edge-character in aged alloy indicates precipitates promoted planar-slip during deformation.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Defect-induced formation and frustration-driven multiple magnetic transitions in Gd 2 Co 0.90 Si 2.90

A new ternary compound, Gd 2 Co 0.90 Si 2.90 , has been synthesized in a chemically single phase by deliberately introducing lattice vacancies in the Co and Si sites. The system is characterized by DC magnetization, heat capacity, resistivity and density functional theory (DFT) calculations. Here, a detailed experimental study reveals that the system exhibits an antiferromagnetic transition below T N = 11.3 K followed by spin freezing behaviour below T B ~ 4.8 K. An additional high-temperature magnetic transition could also be detected at T H ~ 150 K, which is short range in character and is associated with defect-induced polarization of the conduction electrons. The spin-glass-like state formation in the system is additionally bolstered by the observation of magnetic relaxation and associated aging phenomena as well as the magnetic memory effect. On the basis of non-equilibrium dynamical behaviour, we argue that the glassy state in this compound favours the hierarchical model over the droplet model. DFT calculations and experimental outcomes establish that the ground state is magnetically frustrated due to the small energy difference between distinct spin configurations having closely spaced ground-state energies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Surveillance Report on SAVY 4000 and Hagan Nuclear Material Storage Containers Update for FY2020

A Surveillance Program is in place to assess how nuclear material storage containers at LANL are aging in-service. This program is guided by the LANL Surveillance Plan which is required by DOE M441.1-1. The plan is modified as necessary to ensure that any issues identified during surveillance or laboratory studies are examined in future surveillances, and that any lifetime implications are taken into account. Under the plan, overall container integrity is evaluated by a combination of visual inspections and photographs. Multiple measurements are made to assess the SAVY 4000 performance, including, helium leakage rate, O-ring hardness (durometer), O-ring compression set, filter performance and filter water resistance. The containers for surveillance are chosen annually based on the previous surveillance program results and observations. The surveillance plan targets items believed to provide the greatest challenge to the SAVY 4000 container integrity.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Co-Extrusion of Dissimilar Aluminum Alloys via Shear-Assisted Processing and Extrusion

Bimetallic tubes are used when a component requires more than one performance requirement, for instance, strength/creep resistance and oxidation/corrosion resistance. Shear-assisted processing and extrusion (ShAPE) can be used to fabricate extrudates that are comparable or superior in performance relative to conventionally manufactured extrudates. For the first time, ShAPE has been successfully employed in producing bimetallic Al tubing consisting of 6061 and 7075 Al alloys. Both light and electron microscopy techniques were used to investigate the integrity of the tubes, especially the interface between the core and cladding of the bimetallic tubes. Void-free bimetallic tubes were produced using ShAPE. Quantification of tube integrity was carried out with tensile testing under as-extruded and post-aged conditions. All the bimetallic tubes in the as-extruded samples exhibited uniform elongation above 5% with good tensile strength. Key insights such as material flow during bimetallic tube extrusion were obtained from the characterization of remnant billet and simulation results from a smoothed particle hydrodynamics model.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Evaluation of High-Temperature Martensitic Steels for Heavy-Duty Diesel Piston Applications

Five different commercially available high-temperature martensitic steels were evaluated for use in a heavy-duty diesel engine piston application and compared to existing piston alloys 4140 and microalloyed steel 38MnSiVS5 (MAS). Finite element analyses (FEA) were performed to predict the temperature and stress distributions for severe engine operating conditions of interest, and thus aid in the selection of the candidate steels. Complementary material testing was conducted to evaluate the properties relevant to the material performance in a piston. The elevated temperature strength, strength evolution during thermal aging, and thermal property data were used as inputs into the FEA piston models. Additionally, the long-term oxidation performance was assessed relative to the predicted maximum operating temperature for each material using coupon samples in a controlled-atmosphere cyclic-oxidation test rig. A current commercial steel piston alloy, quenched and tempered martensitic steel 4140, was tested in a single-cylinder research engine for a baseline oxidation and mechanical performance assessment using an abbreviated (50h) durability test plan. The predicted suitability of a candidate piston material in an engine is primarily based on its elevated temperature strength, oxidation resistance, and the complex influence of thermal conductivity, the latter of which is substantially lower for the candidate materials considered in this research relative to the traditional alloys. Although the lower thermal conductivity causes the candidate alloys to operate in higher temperature ranges under identical engine operating conditions and piston geometries, increasing the likelihood of partially or completely negating their strength and oxidation resistance advantages relative to 4140 and MAS steels, this evaluation indicates that several of the candidate piston alloys are predicted to enable improved oxidation resistance under more severe engine operating conditions relative to the current piston materials. However, further evaluation is required to determine if the elevated temperature fatigue strength and durability of these alloys are suitable for more severe engine conditions.

36 MATERIALS SCIENCE↗