SEARCH · Search NASA

Results for “Boundary layer structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS1983

The thermal structure of the atmospheric surface boundary layer on Mars as modified by the radiative effect of aeolian dust

A computational simulation, based on Mariner 9 data, was performed for the thermal characteristics of the Martian atmospheric surface boundary layer in clear and dust-filled conditions. A radiative transfer model consisting of the atmospheric enthalpy rate equation, the radiative flux integrated over the 0.2-50 microns, the solid angle interval, and 0.50 km altitudes, broken into 52 levels. Mariner 9 IR data for CO2 absorption lines were included in the form of a temperture-dependent equation, while the line-widths were interpreted in terms of the pressure dependene as well as temperature. The lines covered the regions from 1-50 microns and varying conditions of dust content in the atmosphere. Attention was given to the thermal coupling between the ground and the atmosphere. It was found that convective heat exchange develops quickly due to radiative heating of the Martian desert surface, but does not cool the surface because of the attenuated atmosphere. The model predictd the 100 K temperature variations in the dusty atmosphere, as observed by the Viking thermal mapper. It is suggested that radiative flux convergence is as important as convection at equivalent efficiencies.

Pallmann, A. J.↗

NASA NTRS1983

The structure of a separating turbulent boundary layer. V Frequency effects on periodic unsteady free-stream flows

The results of experimental trials to obtain measurements of the effects of frequency on the sinusoidal variations in the free stream velocity over a separating turbulent boundary layer are reported. An oscillation frequency of 0.596 Hz was examined, in conjunction with a free stream velocity of 10.18 m/sec. Hot-wire anemometers measured the velocity upstream of the separation and the phase-averaged skin friction, while the velocities in the detached flow zone and the downstream velocity were assayed with a laser anemometer. Large amplitude and phase variations developed at the beginning of separation, producing hysteresis in the relationships between flow parameters. Increases in the free stream velocity decreased the detached shear layer thickness, while in the deceleration segment of the cycle the separated shear layer grew thicker. The results are in a frequency range that are significant for axial compressor blades and helicopter blades.

Simpson, R. L.↗

NASA NTRS1986

The structure of the unstable marine boundary layer viewed by lidar and aircraft observations

The marine atmospheric boundary layer (MABL) during a cold-air outbreak off the Atlantic coast between New York and Virginia on January 20, 1983 is characterized on the basis of airborne lidar observations, vertical soundings (potential temperature, vapor mixing ratio, relative humidity, and wind), and horizontal (770-m) temperature records. The data are presented in tables and graphs and analyzed in detail. The organization of the MABL is defined by 1-2-km-scale roll vortices with up and downdrafts of 2-4 m/s at 210 m; north-south orientation of the roll axes (parallel to the low-level winds); rising arms coinciding with updrafts rich in moisture, aerosols, and heat; and 150-200-m (peak-to-trough) undulations of the inversion. Consideration is given to problems inherent in the interpretation of lidar data for MABL studies.

Atlas, D.↗

NASA NTRS1986

Prediction and rational correlation of thermophoretically reduced particle mass transfer to hot surfaces across laminar or turbulent forced-convection gas boundary layers

A formulation previously developed to predict and correlate the thermophoretically-augmented submicron particle mass transfer rate to cold surfaces is found to account for the thermophoretically reduced particle mass transfer rate to overheated surfaces such that thermophoresis brings about a 10-decade reduction below the convective mass transfer rate expected by pure Brownian diffusion and convection alone. Thermophoretic blowing is shown to produce effects on particle concentration boundary-layer (BL) structure and wall mass transfer rates similar to those produced by real blowing through a porous wall. The applicability of the correlations to developing BL-situations is demonstrated by a numerical example relevant to wet-steam technology.

Gokoglu, Suleyman A.↗

NASA NTRS1992

Special Course on Skin Friction Drag Reduction

Lecture notes for the AGARD Fluid Dynamics Panel (FDP) Special Course on 'Skin Friction Drag Reduction' have been assembled in this report. The aim and scope of this course was to provide an overview of the state of the art of current technology programs focused on reducing aircraft drag caused by skin friction. This report provides a review of recent progress in the field of skin friction drag reduction for transport aircraft. It provides a general introduction to the technology and then focuses on two specific aspects of drag reduction: maintaining laminar flow by controlling transition and manipulating the turbulence structure in boundary layers to help reduce skin friction. Technology associated with the use of riblets, LEBU, polymers, additives, etc., is also reviewed.

Advisory Group for Aerospace Research and Developm↗

NASA NTRS2004

First Atmospheric Science Results from the Mars Exploration Rovers Mini-TES

Thermal infrared spectra of the martian atmosphere taken by the Miniature Thermal Emission Spectrometer (Mini-TES) were used to determine the atmospheric temperatures in the planetary boundary layer and the column-integrated optical depth of aerosols. Mini-TES observations show the diurnal variation of the martian boundary layer thermal structure, including a near-surface superadiabatic layer during the afternoon and an inversion layer at night. Upward-looking Mini-TES observations show warm and cool parcels of air moving through the Mini-TES field of view on a time scale of 30 seconds. The retrieved dust optical depth shows a downward trend at both sites.

Mars↗

NASA NTRS2008

Estimating Mixing Heights Using Microwave Temperature Profiler

A paper describes the Microwave Temperature Profiler (MTP) for making measurements of the planetary boundary layer thermal structure data necessary for air quality forecasting as the Mixing Layer (ML) height determines the volume in which daytime pollution is primarily concentrated. This is the first time that an airborne temperature profiler has been used to measure the mixing layer height. Normally, this is done using a radar wind profiler, which is both noisy and large. The MTP was deployed during the Texas 2000 Air Quality Study (TexAQS-2000). An objective technique was developed and tested for estimating the ML height from the MTP vertical temperature profiles. In order to calibrate the technique and evaluate the usefulness of this approach, estimates from a variety of measurements during the TexAQS-2000 were compared. Estimates of ML height were used from radiosondes, radar wind profilers, an aerosol backscatter lidar, and in-situ aircraft measurements in addition to those from the MTP.

Nielson-Gammon, John↗

NASA NTRS2015

Covariance Between Arctic Sea Ice and Clouds Within Atmospheric State Regimes at the Satellite Footprint Level

Understanding the cloud response to sea ice change is necessary for modeling Arctic climate. Previous work has primarily addressed this problem from the interannual variability perspective. This paper provides a refined perspective of sea ice-cloud relationship in the Arctic using a satellite footprint-level quantification of the covariance between sea ice and Arctic low cloud properties from NASA A-Train active remote sensing data. The covariances between Arctic low cloud properties and sea ice concentration are quantified by first partitioning each footprint into four atmospheric regimes defined using thresholds of lower tropospheric stability and mid-tropospheric vertical velocity. Significant regional variability in the cloud properties is found within the atmospheric regimes indicating that the regimes do not completely account for the influence of meteorology. Regional anomalies are used to account for the remaining meteorological influence on clouds. After accounting for meteorological regime and regional influences, a statistically significant but weak covariance between cloud properties and sea ice is found in each season for at least one atmospheric regime. Smaller average cloud fraction and liquid water are found within footprints with more sea ice. The largest-magnitude cloud-sea ice covariance occurs between 500m and 1.2 km when the lower tropospheric stability is between 16 and 24 K. The covariance between low cloud properties and sea ice is found to be largest in fall and is accompanied by significant changes in boundary layer temperature structure where larger average near-surface static stability is found at larger sea ice concentrations.

Taylor, Patrick C.↗

NASA NTRS2016

Influence of Stationary Crossflow Modulation on Secondary Instability

A likely scenario for swept wing transition on subsonic aircraft with natural laminar flow involves the breakdown of stationary crossflow vortices via high frequency secondary instability. A majority of the prior research on this secondary instability has focused on crossflow vortices with a single dominant spanwise wavelength. This paper investigates the effects of the spanwise modulation of stationary crossflow vortices at a specified wavelength by a subharmonic stationary mode. Secondary instability of the modulated crossflow pattern is studied using planar, partial-differential-equation based eigenvalue analysis. Computations reveal that weak modulation by the first subharmonic of the input stationary mode leads to mode splitting that is particularly obvious for Y-type secondary modes that are driven by the wall-normal shear of the basic state. Thus, for each Y mode corresponding to the fundamental wavelength of results in unmodulated train of crossflow vortices, the modulated flow supports a pair of secondary modes with somewhat different amplification rates. The mode splitting phenomenon suggests that a more complex stationary modulation such as that induced by natural surface roughness would yield a considerably richer spectrum of secondary instability modes. Even modest levels of subharmonic modulation are shown to have a strong effect on the overall amplification of secondary disturbances, particularly the Z-modes driven by the spanwise shear of the basic state. Preliminary computations related to the nonlinear breakdown of these secondary disturbances provide interesting insights into the process of crossflow transition in the presence of the first subharmonic of the dominant stationary vortex.

Vortex structure↗

NASA NTRS1976

Simulation of the atmospheric boundary layer in the wind tunnel for modeling of wind loads on low-rise structures

The lower part of the atmospheric boundary layer (strong wind conditions) was simulated in low speed wind tunnel for the modeling of wind loads on low-rise structures. The turbulence characteristics of the turbulent boundary layer in the wind tunnel are compared with full scale measurements and with measurements made at NASA Wallops Flight Center. Wind pressures measured on roofs of a 1:70 scale model of a small single family dwelling were compared with results obtained from full scale measurements. The results indicate a favorable comparison between full scale and model pressure data as far as mean, r.m.s. and peak pressures are concerned. In addition, results also indicate that proper modeling of the turbulence is essential for proper simulation of the wind pressures.

Tieleman, H. W.↗

NASA NTRS1990

Structure of three-dimensional turbulent boundary layers

The changes that occur in the Reynolds-stress-producing motion when a cross-stream pressure gradient is applied to an initially two-dimensional turbulent flow are discussed. Two examples are used: (1) a temporal simulation of a channel flow with crossflow applied by a spanwise pressure gradient for t is greater than 0; and (2) a spatial simulation of the boundary layer on an infinite swept wing. Evidence examined to date suggests that the structural changes in the two cases are similar, but the mechanisms may be significantly different, even if effects peculiar to the viscous wall region are ignored. The results from (2) are provisional, based on too short a time series for accurate statistical averages to be obtained. We treat turbulence 'statistics' (solutions of the Navier-Stokes equations in three space dimensions and time) in the same way as experiments: both have limitations of accuracy but both are acceptable representations of real fluid flows.

Bradshaw, P.↗

NASA NTRS1988

Structure of rough-wall turbulent boundary layers

Recent experiments have shown that, in rough-wall turbulent boundary layers, drag varies systematically with the spanwise aspect ratio lambda(z) (span/height) of roughness elements. In this paper, the effect of lambda(z) on turbulence structure has been examined. Based on lambda(z), the roughness in a transversely grooved surface with lambda(z) much greater than 1 is the opposite extreme of model plant canopies with lambda(z) much less than 1, studied in wind tunnels, whereas sandgrain is an intermediate type. Second-, third-, and fourth-order turbulence moments have been measured in turbulent boundary layers over transversely grooved and smooth surfaces and compared with available turbulence structure measurements over other types of surfaces. The near-wall turbulence structure is found to vary with lambda(z). The instantaneous motions involved in the flux of shear stress near the wall in smooth and transversely grooved surfaces are opposite in sign to those in three-dimensional roughness. The former is explained in terms of hairpin vortices alone, while the latter group is modeled to have an additional vortex (the so-called necklace vortex which straddles a three-dimensional roughness element near its base).

Bandyopadhyay, Promode R.↗

NASA NTRS1990

Control of the vortical structure in the early stages of transition in boundary layers

The effect of suction and pressure gradient on controlling the production of the three-dimensional vortical structure due to secondary instability is investigated for a boundary layer in the presence of small but finite amplitude Tollmien-Schlichting wave. The subharmonic instability is the focus of the study due to its realistic application in low disturbance flight environment. The spanwise wavelength of the most unstable secondary subharmonic disturbance increases with the increase of control indicating possible alteration of the flow structure from H-type to C-type.

El-Hady, Nabil M.↗

NASA NTRS1976

A complete model of turbulence

A set of constitutive equations suitable for a priori computation of turbulent shear flows has been developed. Since no properties of a given turbulent flow need be known in advance in order to obtain a solution, the equations comprise a complete model of turbulence. Perturbation analysis shows that the model predicts a composite five-layer structure for an incompressible turbulent boundary layer, viz, a defect layer, a law-of-the-wall layer, a viscous sublayer, a near-surface roughness layer, and a viscous superlayer at the boundary-layer edge. Analysis of the defect layer demonstrates the key improvement of the model over its predecessor, the Saffman-Wilcox two-equation model of turbulence. Examination of model-predicted sublayer structure yields model-parameter boundary conditions appropriate for surfaces with roughness and mass injection. Results of numerical computations of compressible and incompressible equilibrium boundary layers show that, for such flows, the model is as accurate as mixing-length theory. Applications to transitional boundary layers and to nonequilibrium relaxation of a boundary layer passing from a rough to a smooth surface indicate that the model's applicability extends far beyond that of mixing-length theory's.

Wilcox, D. C.↗

NASA NTRS1986

Observations of a large-scale vortex-like structure in the deep-tail plasma sheet boundary layer

ISEE-3 observations of a large-scale vortexlike structure in the deep tail of the magnetosphere at X(GSM) = -217 earth radii are reported. The structure is characterized by two clockwise rotations of the energetic-ion anisotropy vector. Variations in the magnetic-field vector approximately 180 deg out of phase with the ion variations are observed. This structure is most likely the signature within the magnetosphere of a surface wave at the magnetopause driven by a Kelvin-Helmholtz instability. Conditions inside and outside of the magnetosphere, as observed by ISEE-3 and ISEE-2, respectively, are examined; these conditions suggest that the surface wave is most likely propagating in the slow mode.

Sanderson, T. R.↗

NASA NTRS1983

Flat-plate drag measurements with vortex generators in turbulent boundary layer

Direct drag measurements were obtained on a flat plate with a spanwise row of vortex generators near the leading edge, to produce an array of stream wise vortices within the approaching turbulent boundary layer. The object was to explore the possibility of modifying the large scale structure of the boundary layer through embedded longitudinal vortices with a view to obtaining a reduction in wall shear. Both obstacle and vane type vortex generators were tested at free stream velocities 40 ft/sec to 130 ft/sec corresponding to plate length Reynolds no. 0.3 million to 0.8 million with a nominal boundary layer thickness of approximately 0.6 in. at the leading edge. A few vortex generator configurations were tested both on and off the plate to measure the total drag as well as the plate drag alone. The obstacle type devices reduced the plate drag, indicating that the wake momentum defect predominated even in the presence of streamwise vortices. The vane type vortex generators however always increased the plate drag.

Rao, D. M.↗

NASA NTRS2014

Computational Aerodynamic Simulations of an 840 ft/sec Tip Speed Advanced Ducted Propulsor Fan System Model for Acoustic Methods Assessment and Development

Computational Aerodynamic simulations of an 840 ft/sec tip speed, Advanced Ducted Propulsor fan system were performed at five different operating points on the fan operating line, in order to provide detailed internal flow field information for use with fan acoustic prediction methods presently being developed, assessed and validated. The fan system is a sub-scale, lownoise research fan/nacelle model that has undergone extensive experimental testing in the 9- by 15- foot Low Speed Wind Tunnel at the NASA Glenn Research Center, resulting in quality, detailed aerodynamic and acoustic measurement data. Details of the fan geometry, the computational fluid dynamics methods, the computational grids, and various computational parameters relevant to the numerical simulations are discussed. Flow field results for three of the five operating conditions simulated are presented in order to provide a representative look at the computed solutions. Each of the five fan aerodynamic simulations involved the entire fan system, excluding a long core duct section downstream of the core inlet guide vane. As a result, only fan rotational speed and system bypass ratio, set by specifying static pressure downstream of the core inlet guide vane row, were adjusted in order to set the fan operating point, leading to operating points that lie on a fan operating line and making mass flow rate a fully dependent parameter. The resulting mass flow rates are in good agreement with measurement values. The computed blade row flow fields for all five fan operating points are, in general, aerodynamically healthy. Rotor blade and fan exit guide vane flow characteristics are good, including incidence and deviation angles, chordwise static pressure distributions, blade surface boundary layers, secondary flow structures, and blade wakes. Examination of the computed flow fields reveals no excessive boundary layer separations or related secondary-flow problems. A few spanwise comparisons between computational and measurement data in the bypass duct show that they are in good agreement, thus providing a partial validation of the computational results.

Tweedt, Daniel L.↗

NASA NTRS1991

A viscous flow study of shock-boundary layer interaction, radial transport, and wake development in a transonic compressor

A numerical study based on the 3D Reynolds-averaged Navier-Stokes equation has been conducted to investigate the detailed flow physics inside a transonic compressor. 3D shock structure, shock-boundary layer interaction, flow separation, radial mixing, and wake development are all investigated at design and off-design conditions. Experimental data based on laser anemometer measurements are used to assess the overall quality of the numerical solution. An additional experimental study to investigate end-wall flow with a hot-film was conducted, and these results are compared with the numerical results. Detailed comparison with experimental data indicates that the overall features of the 3D shock structure, the shock-boundary layer interaction, and the wake development are all calculated very well in the numerical solution. The numerical results are further analyzed to examine the radial mixing phenomena in the transonic compressor. A thin sheet of particles is injected in the numerical solution upstream of the compressor. The movement of particles is traced with a 3D plotting package. This numerical survey of tracer concentration reveals the fundamental mechanisms of radial transport in this transonic compressor.

Hah, Chunill↗