Search NASA⌕ Search

SEARCH · Search NASA

Results for “COUPLING CONSTANT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Adhesion Between Volcanic Glass and Spacecraft Materials in an Airless Body Environment

The successful exploration of airless bodies, such as the Earth s moon, many smaller moons of the outer planets (including those of Mars) and asteroids, will depend on the development and implementation of effective dust mitigation strategies. The ultrahigh vacuum environment (UHV) on the surfaces of these bodies, coupled with constant ion and photon bombardment from the Sun and micrometeorite impacts (space weathering), makes dust adhesion to critical spacecraft systems a severe problem. As a result, the performance of thermal control surfaces, photovoltaics and mechanical systems can be seriously degraded even to the point of failure. The severe dust adhesion experienced in these environments is thought to be primarily due to two physical mechanisms, electrostatic attraction and high surface energies, but the dominant of these has yet to be determined. The experiments presented here aim to address which of these two mechanisms is dominant by quantifying the adhesion between common spacecraft materials (polycarbonate, FEP and PTFE Teflon, (DuPont) Ti-6-4) and a synthetic noritic volcanic glass, as a function of surface cleanliness and triboelectric charge transfer in a UHV environment. Adhesion force has been measured between pins of spacecraft materials and a plate of synthetic volcanic glass by determining the pull-off force with a torsion balance. Although no significant adhesion is observed directly as a result of high surface energies, the adhesion due to induced electrostatic charge is observed to increase with spacecraft material cleanliness, in some cases by over a factor of 10, although the increase is dependent on the particular material pair. The knowledge gained by these studies is envisioned to aid the development of new dust mitigation strategies and improve existing strategies by helping to identify and characterize mechanisms of glass to spacecraft adhesion for norite volcanic glass particles. Furthermore, the experience of the Apollo missions revealed that dust mitigation strategies must be subjected to high fidelity tests. To facilitate the effectiveness of ground-based testing of mitigation strategies, the issue of a pressure limit for high fidelity tests will be addressed.

Berkebile, Stephen↗
NASA NTRS1977

Reaction diffusion in the nickel-chromium-aluminum and cobalt-chromium-aluminum systems

The effects of MCrAl coating-substrate interdiffusion on oxidation life and the general mutliphase, multicomponent diffusion problem were examined. Semi-infinite diffusion couples that had sources representing coatings and sinks representing gas turbine alloys were annealed at 1,000, 1,095, 1,150, or 1,205 C for as long as 500 hours. The source and sink aluminum and chromium contents and the base metal (cobalt or nickel) determined the parabolic diffusion rate constants of the couples and predicted finite coating lives. The beta source strength concept provided a method (1) for correlating beta recession rate constants with composition; (2) for determining reliable average total, diffusion, and constitutional activation energies; and (3) for calculating interdiffusion coefficients.

Levine, S. R.↗
NASA NTRS1978

Considerations in the design of tip-coupled air-transport systems

It is shown that the lift-drag ratio of tip-coupled systems can be expressed as a simple multiple of the lift-drag ratio of the isolated units comprising the system. When operated for maximum lift-drag ratio, the extent of the coupled system is limited by maximum lift coefficient, high-altitude engine characteristics, and degraded performance of the isolated unit climbing to couple into the system. When operated at constant altitude, the gain from coupling is severely limited. If the cruise altitude is that for best performance of the isolated unit, the system lift-drag ratio can be no better than twice that of the isolated unit even when an infinite number of units are coupled. System performance may be further degraded since span-load distributions which yield good performance for the individual units reduce the efficiency of the coupled system. Coupling a pair of modern transport aircraft results in only about half the expected gain because of a poor span-distribution across the coupled pair. The control deflections required to maintain roll and pitch equilibrium further degrade the possible gain.

Heyson, H. H.↗
DOE OSTI2025

Deconstruction of the Anisotropic Magnetic Interactions from Spin‐Entangled Optical Excitations in van der Waals Antiferromagnets

Magneto-optical excitations in antiferromagnetic d systems can originate from a multiplicity of light-spin and spin-spin interactions, as the light and spin degrees of freedom can be entangled. This is exemplified in van der Waals systems with attendant strong anisotropy between in-plane and out-of-plane directions, such as MnPS 3 and NiPS 3 films studied here. The rich interplay between the magnetic ordering and sub-bandgap optical transitions poses a challenge to resolve the mechanisms driving spin-entangled optical transitions, as well as the single-particle bandgap itself. Here, a high-fidelity ab initio theory is applied to find a realistic estimation of the bandgap by elucidating the atom- and orbital-resolved contributions to the fundamental sub-bands. It is further demonstrated that the spin-entangled excitations, observable as photoluminescence and absorption resonances, originate from an on-site spin-flip transition confined to a magnetic atom (Mn or Ni). The evolution of the spin-flip transition in a magnetic field is used to deduce the effective exchange coupling and anisotropy constants.

2D materials↗
NASA NTRS1972

Augmentation of heat transfer by subsonic diffusion at a nearly separated state

Measurements of mean velocity, turbulence intensity, and wall heat transfer were obtained in a 13 deg total angle of divergence conical diffuser coupled to a constant diameter recovery section. The results indicated that the boundary layer was in a nearly separated state. Turbulence intensity levels approaching 0.4 were observed in the latter stages of diffusion. The convective heat transfer was always equal to or higher than corresponding values for fully developed pipe flow at the same Reynolds number. The augmentation in heat transfer was greatest during the latter stages of diffusion where the Stanton number was nearly three times the pipe flow value.

Boldman, D. R.↗
NASA NTRS1973

Experimental and analytical study of a conically diffused flow with a nearly separated boundary layer

Turbulence measurements were obtained in the nearly separated flow in a 13 deg total angle of divergence conical diffuser coupled to a constant area tailpipe. Air at 207 newtons per square centimeter and 308 K provided an inlet velocity of about 51 meters per second at an inlet unit Reynolds number of 63.7 million per meter. Very high longitudinal turbulence intensities accompanied the diffusion process with peak values approaching 40 percent when normalized by the local centerline velocity. Predictions of the pressure recovery coefficient using a mixing length concept were good in the early stages of diffusion. In the latter stages of diffusion satisfactory predictions of the pressure recovery were obtained with an empirical method.

Boldman, D. R.↗
NASA NTRS1979

Turbulence measurements in the compressor exit flow of a General Electric CF6-50 engine

Ruggedized cooled film probes were used to measure CF6-50 compressor exit turbulence properties at three different engine idle condition test points. The turbulence probe was coupled to a constant temperature anemometer and signal conditioning system. An on-line readout system connected to the anemometer was used to check the data as it was acquired. At engine idle conditions, the turbulence intensity ranged from 4.8 percent to 5.6 percent and the length scale ranged from 5.64 cm to 6.95 cm. The length scale values are somewhat larger than the passage height at the measurement plane (5.54 cm), which indicates that the shape of the turbulent eddies are elongated in the axial direction. The microscale values range from about 0.73 cm to about 0.98 cm. Power spectral density distributions show that a large proportion of the turbulent energy at the measurement plane is concentrated at frequencies below one kilohertz.

Taylor, J. R.↗
NASA NTRS1950

Study of compressor systems for a gas-generator engine

Various methods of providing compressor-capacity and pressure-ratio control in the gas-generator type of compound engine over a range of altitudes from sea level to 50,000 feet are presented. The analytical results indicate that the best method of control is that in which the first stage of compression is carried out in a variable-speed supercharger driven by a hydraulic slip coupling. The constant-speed second stage could be either a mixed-flow rotary compressor or a piston-type compressor. A variable-area turbine nozzle is shown to be unnecessary for cruising operation of the engine.

Sather, Bernard I↗
NASA NTRS2003

SWIFT BAT Loop Heat Pipe Thermal System Characteristics and Ground/Flight Operation Procedure

The SWIFT Burst Alert Telescope (BAT) Detector Array has a total power dissipation of 208 W. To meet the stringent temperature gradient and thermal stability requirements in the normal operational mode, and heater power budget in both the normal operational and safehold modes, the Detector Array is thermally well coupled to eight constant conductance heat pipes (CCHPs) embedded in the Detector Array Plate (DAP), and two loop heat pipes (LHPs) transport heat fiom the CCHPs to a radiator. The CCHPs have ammonia as the working fluid and the LHPs have propylene as the working fluid. Precision heater controllers, which have adjustable set points in flight, are used to control the LHP compensation chamber and Detector Array XA1 ASIC temperatures. The radiator has the AZ-Tek AZW-LA-II low-alpha white paint as the thermal coating and is located on the anti-sun side of the spacecraft. This paper presents the characteristics, ground operation and flight operation procedures of the LHP thermal system.

Choi, Michael K.↗
NASA NTRS2004

Thermal Vacuum/Balance Test Results of Swift BAT with Loop Heat Pipe Thermal System

The Swift Burst Alert Telescope (BAT) Detector Array is thermally well coupled to eight constant conductance heat pipes (CCHPs) embedded in the Detector Array Plate PAP), and two loop heat pipes (LHPs) transport heat from the CCHPs to a radiator. The CCHPs have ammonia as the working fluid and the LHPs have propylene as the working fluid. Precision heater controllers, which have adjustable set points in flight, are used to control the LHP compensation chamber and Detector Array xA1 ASIC temperatures. The radiator has AZ-Tek's AZW-LA-II low solar absorptance white paint as the thermal coating, and is located on the anti-sun side of the spacecraft. A thermal balance (T/B) test on the BAT was successfully completed. It validated that the thermal design satisfies the temperature requirements of the BAT in the flight thermal environments. Instrument level and observatory level thermal vacuum (TN) cycling tests of the BAT Detector Array by using the LHP thermal system were successfully completed. This paper presents the results of the T/B test and T N cycling tests.

Choi, Michael K.↗