Search NASA⌕ Search

SEARCH · Search NASA

Results for “CRM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Building a Practical Natural Laminar Flow Design Capability

A preliminary natural laminar flow (NLF) design method that has been developed and applied to supersonic and transonic wings with moderate-to-high leading-edge sweeps at flight Reynolds numbers is further extended and evaluated in this paper. The modular design approach uses a knowledge-based design module linked with different flow solvers and boundary layer stability analysis methods to provide a multifidelity capability for NLF analysis and design. An assessment of the effects of different options for stability analysis is included using pressures and geometry from an NLF wing designed for the Common Research Model (CRM). Several extensions to the design module are described, including multiple new approaches to design for controlling attachment line contamination and transition. Finally, a modification to the NLF design algorithm that allows independent control of Tollmien-Schlichting (TS) and cross flow (CF) modes is proposed. A preliminary evaluation of the TS-only option applied to the design of an NLF nacelle for the CRM is performed that includes the use of a low-fidelity stability analysis directly in the design module.

Campbell, Richard L.↗

Noise Simulations of the High-Lift Common Research Model

The PowerFLOW(TradeMark) code has been used to perform numerical simulations of the high-lift version of the Common Research Model (HL-CRM) that will be used for experimental testing of airframe noise. Time-averaged surface pressure results from PowerFLOW(TradeMark) are found to be in reasonable agreement with those from steady-state computations using FUN3D. Surface pressure fluctuations are highest around the slat break and nacelle/pylon region, and synthetic array beamforming results also indicate that this region is the dominant noise source on the model. The gap between the slat and pylon on the HL-CRM is not realistic for modern aircraft, and most nacelles include a chine that is absent in the baseline model. To account for those effects, additional simulations were completed with a chine and with the slat extended into the pylon. The case with the chine was nearly identical to the baseline, and the slat extension resulted in higher surface pressure fluctuations but slightly reduced radiated noise. The full-span slat geometry without the nacelle/pylon was also simulated and found to be around 10 dB quieter than the baseline over almost the entire frequency range. The current simulations are still considered preliminary as changes in the radiated acoustics are still being observed with grid refinement, and additional simulations with finer grids are planned.

Lockard, David P.↗

Nonlinear Large Deflection Theory with Modified Aeroelastic Lifting Line Aerodynamics for a High Aspect Ratio Flexible Wing

This paper investigates the effect of nonlinear large deflection bending on the aerodynamic performance of a high aspect ratio flexible wing. A set of nonlinear static aeroelastic equations are derived for the large bending deflection of a high aspect ratio wing structure. An analysis is conducted to compare the nonlinear bending theory with the linear bending theory. The results show that the nonlinear bending theory is length-preserving whereas the linear bending theory causes a non-physical effect of lengthening the wing structure under the no axial load condition. A modified lifting line theory is developed to compute the lift and drag coefficients of a wing structure undergoing a large bending deflection. The lift and drag coefficients are more accurately estimated by the nonlinear bending theory due to its length-preserving property. The nonlinear bending theory yields lower lift and span efficiency than the linear bending theory. A coupled aerodynamic-nonlinear finite element model is developed to implement the nonlinear bending theory for a Common Research Model (CRM) flexible wing wind tunnel model to be tested in the University of Washington Aeronautical Laboratory (UWAL). The structural stiffness of the model is designed to give about 10% wing tip deflection which is large enough that could cause the nonlinear deflection effect to become significant. The computational results show that the nonlinear bending theory yields slightly less lift than the linear bending theory for this wind tunnel model. As a result, the linear bending theory is deemed adequate for the CRM wind tunnel model.

Aeroelasticity↗

Contributions to HiLiftPW-3 Using Structured, Overset Grid Methods

The High-Lift Common Research Model (HL-CRM) and the JAXA Standard Model (JSM) were analyzed computationally using both the OVERFLOW and LAVA codes for the third AIAA High-Lift Prediction Workshop. Geometry descriptions and the test cases simulated are described. With the HL-CRM, the effects of surface smoothness during grid projection and the effect of partially sealing a flap gap were studied. Grid refinement studies were performed at two angles of attack using both codes. For the JSM, simulations were performed with and without the nacelle/pylon. Without the nacelle/pylon, evidence of multiple solutions was observed when a quadratic constitutive relation is used in the turbulence modeling; however, using time-accurate simulation seemed to alleviate this issue. With the nacelle/pylon, no evidence of multiple solutions was observed. Laminar-turbulent transition modeling was applied to both JSM configuration, and had an overall favorable impact on the lift predictions.

HiLiftPW-3↗

Addressing Human Error in International Space Station Flight Control Teams: Advances in Ground Training for Science Operators

In flight control, as with any human in the loop system, operator error is an inevitable reality. On the International Space Station (ISS) where crew time and physical resources are precious and often irreplaceable, operator errors can result in significant, irreversible consequences. Flight controllers at the Payload Operations Integration Center (POIC) located at NASA’s Marshall Space Flight Center (MSFC) in Huntsville, Alabama know this reality well. At the POIC, operator errors can be caused by a variety of factors, from poor hardware or software design to environmental factors such as time pressure or fatigue. The most difficult errors to address, however, are those which result from ineffective teamwork.Academic research in teamwork has resulted in the identification of many factors which make cross-functional teaming difficult, including leadership, trust building, and communication challenges. These factors, especially when combined with the challenging environmental factors flight control teams must contend with daily, make the goal of minimizing operator errors in payload operations challenging to achieve. To address such teamwork errors, trainers at the POIC have drawn best practices from high reliability industries such as commercial aviation, healthcare, and nuclear power plants, as well as from our sister ISS control center in Houston, Texas, to develop and institute a new training program focused specifically on teamwork skills.This training program, called the Team Skills Curriculum, is based on the concept of Crew Resource Management (CRM) which was developed by NASA in the 1970s for the commercial aviation industry in response to a series of aviation disasters resulting from ineffective teamwork. CRM was later tailored by the Johnson Space Center (JSC) for use in astronaut and flight control training. The result, called Space Flight Resource Management (SFRM) was formally introduced into manned spaceflight training in the late 90s. SFRM has evolved over the years, but the focus has remained on helping operators develop the skills needed to work as part of an effective team. Using these concepts as well as the latest research in cross-functional teaming and data on specific errors occurring at the POIC, trainers in the integrated flight control training branch created a custom training program for both new and certified payload operations specialists.

Harris, Samantha S.↗

Preparation and Analysis of the Geometry Models used in the 1st AIAA Geometry and Mesh Generation Workshop

The NASA High-Lift Common Research Model (HL-CRM) was the subject model chosen for the AIAA Geometry and Mesh Generation Workshop I (GMGW-1) and High-Lift Prediction Workshop III (HLPW-3). This paper describes how geometry models of the HLCRM were prepared for use in the workshops and reviews the analysis of their construction that was provided to workshop participants. The refinements made to the HL-CRM geometry model immediately after GMGW-1 are also presented.

Taylor, Nigel J.↗

Real-Time Adaptive Drag Minimization Wind Tunnel Investigation of a Flexible Wing with Variable Camber Continuous Trailing Edge Flap System

This paper reports the results of a recently completed real-time adaptive drag minimization wind tunnel investigation of a highly flexible wing wind tunnel model equipped with the Variable Camber Continuous Trailing Flap (VCCTEF) technology at the University of Washington Aeronautical Laboratory (UWAL). The wind tunnel investigation is funded by NASA SBIR Phase II contract with Scientific Systems Company, Inc. (SSCI) and University of Washington (UW) as a subcontractor. The wind tunnel model is a sub-scale Common Research Model (CRM) wing constructed of foam core and fiberglass skin and is aeroelastically scaled to achieve a wing tip deflection of 10% of the wing semi-span which represents a typical wing tip deflection for a modern transport such as Boeing 787. The jig-shape twist of the CRM wing is optimized using a CART3D aero-structural model to achieve the minimum induced drag for the design cruise lift coefficient of 0.5. The wing is equipped with two chord wise cambered segments for each of the six span wise flap sections for a total of 12 individual flap segments that comprise the VCCTEF system. Each of the 12 flap segments is actively controlled by an electric servo-actuator. The real-time adaptive drag optimization strategy includes an on-board aerodynamic model identification, a model excitation, and a real-time drag optimization. The on-board aerodynamic model is constructed parametrically as a function of the angle of attack and flap positions to model the lift and drag coefficients of the wing. The lift coefficient models include a linear model and a second-order model. The drag coefficient models include a quadratic model and a higher-order up to 6th-order model to accurately model the drag coefficient at high angles of attack. The onboard aerodynamic model identification includes a recursive least-squares (RLS) algorithm and a batch least-squares (BLS) algorithm designed to estimate the model parameters. The model excitation method is designed to sample the input set that comprises the angle of attack and the flap positions. Three model excitation methods are developed: random excitation method, sweep method, and iterative angle-of-attack seeking method. The real-time drag optimization includes a generic algorithm developed by SSCI and several optimization methods developed by NASA which include a second-order gradient Newton-Raphson optimization method, an iterative gradient optimization method, a pseudo-inverse optimization method, an analytical optimization method, and an iterative refinement optimization method. The first wind tunnel test entry took place in September 2017. This test revealed major hardware issues and required further redesign of the flap servo mechanisms. The second test entry took place in April 2018. However, the test was not successful due to the issues with the onboard aerodynamic model identification RLS algorithm which incorrectly identified model parameters. This test also provides an experimental comparison study between the VCCTEF and a variable camber discrete trailing edge flap (VCDTEF) without the elastomer transition mechanisms. The experimental result confirms the benefit of the VCCTEF which produces lower drag by 5% than the VCDTEF. The third and final test entry took place in June 2018 after the issues with the RLS algorithm have been identified and corrected. Additional improvements were implemented. These include the BLS algorithm, the iterative angle-of-attack seeking method, the iterative gradient optimization method, and the pseudo-inverse optimization method. The test objectives were successfully demonstrated as the real-time drag optimization identifies several optimal solutions at off-design lift coefficients. The iterative gradient optimization method is found to achieve up to 4.7% drag reduction for the off-design lift coefficient of 0.7. The pseudo-inverse optimization method which does not require the drag coefficient model is found to be quite effective in reducing drag. Up to 9.4% drag reduction for the off-design lift coefficient of 0.7 is achieved with the pseudo-inverse optimization method. The wind tunnel investigation demonstrates the potential of real-time drag optimization technology. Several new capabilities are developed that could enable future adaptive wing technologies for flexible wings equipped with drag control devices such as the VCCTEF.

Drag Optimization↗

Assessment of Transition Modeling Capability in OVERFLOW with Emphasis on Swept-Wing Configurations

In preparation for comparisons with data obtained from the recently concluded experiments in the National Transonic Facility at the NASA Langley Research Center on the new common research model with natural laminar flow (CRM-NLF), an assessment of the current transition modeling capability in the NASA OVERFLOW 2.2o code has been carried out. A combination of the available experimental data and linear stability analysis is used to evaluate the accuracy and robustness of these models for selected swept-wing type configurations, with significant crossflow. An additional goal for this work involves providing a comparative assessment of the relevant transition models in the context of a single flow solver and identifying model limitations as well as the potential for future improvements that would help strengthen the physical basis of such transition models. Included in this investigation is an assessment of the sensitivities of the underlying transition models to grid resolution (wall-normal, as well as streamwise and spanwise) and the values of extra input parameters such as the level of surface roughness and freestream turbulence variables. The flow configurations targeted in this assessment include the NASA NLF(2)-0415 swept-wing configuration, the sickle-shaped wing introduced by the Technical University of Braunschweig, and the wing-body configuration of the CRM model from the fourth and fifth AIAA CFD Drag Prediction Workshops.

Freestream velocity↗

FLEET Velocimetry in the Common Research Model’s Wing Wake

Femtosecond laser electronic excitation tagging was used to make velocity measurements in the wake of the wing of the Common Research Model (CRM). Experiments were performed in the NASA Langley Research Center’s National Transonic Facility over a range of tunnel operating conditions. Pressures ranged from 205 to 411 kPa, temperatures from 278 to 323 K, and Mach from 0.1 to 0.9. Velocity was also determined over a range of model angles of attack. Time-averaged velocity results were obtained in both air and nitrogen, while single-shot velocity was obtained under certain tunnel operating conditions. Spatially-resolved, two dimensional, single component velocity measurements were achieved using a newly-developed laser scanning technique, which proved sufficiently sensitive to measure an approximately 5% velocity deficit in the wing wake region of the CRM.

Daniel T Reese↗

TPSAS-NF1676L-22800-DND

This lecture will provide an overview of an advanced turbulence closure scheme used in cloud-resolving models (CRMs) and climate modeling effort with the superparameterization approach. The CRM is embedded into each atmospheric column of a climate model as a super parameterization. It replaces the traditional subgrid-scale physical parameterizations in a conventional climate model. Two sensitivity simulations with doubling of CO2 and an increase of sea surface temperature, respectively, are performed and compared to similar simulations without this advanced turbulence closure in CRM to better understand the role of low-level clouds in climate sensitivity.

Kuan-Man Xu↗

Requirements and Challenges for CFD Validation within the High-Lift Common Research Model Ecosystem

The High-Lift Common Research Model (CRM-HL) ecosystem is envisioned to become an industry standard set of test cases for high-lift aerodynamics prediction, with data generated providing a strong foundation for CFD validation. Since its original development, preliminary wind tunnel tests have been conducted to further understand and configure the geometry, and several more are in the planning phases. It is anticipated that the data generated in these tests will be used extensively by the CFD community for research, development, and validation of new techniques that yield more accurate results. To derive the maximum benefit from planned wind tunnel testing, data acquisition will be focused in several key areas to address specific shortcomings in CFD predictive capabilities. Significant challenges currently exist in areas including, but not limited to, characterizing high-lift flow phenomena, quantifying effects due to configuration changes, understanding wind tunnel and model installation effects, and establishing data uncertainty. This paper will discuss the current state-of-the-art in high-lift CFD prediction, key limitations of current CFD methods and tools, establishing a validation dialog between test and CFD practitioners, and the flow phenomena of highest interest, in an effort to begin to address these challenges. To this end, it is expected that the data generated from CRM-HL tests will form a strong foundation for future predictive capability.

Adam M Clark↗

Summary of the NASA Semi-Span High-Lift Common Research Model Wind Tunnel Test at the QinetiQ 5-Metre Low-Speed Facility

A summary and selected results from experimental testing of the NASA 10% scale semi-span High-Lift Common Research Model (CRM-HL) at the QinetiQ 5m (5mWT) pressurized low-speed wind tunnel are presented. There were many objectives of this test, the primary being to define a set of reference configurations for dissemination and use within the CRM-HL ecosystem, one in the landing configuration and one in the takeoff configuration. A database of force, moment, pressure and surface flow visualization data was collected to support several objectives: aerodynamic sensitivity to high-lift device positioning, Reynolds number effects on configuration selection, isolation of the effects of various components of the reference configuration e.g. landing gear, nacelle, horizontal tail, etc., and limited repeatability data for uncertainty quantification assessment. Some results were compared to limited data collected at the NASA Langley Research Center 14x22 wind tunnel to assess half-model effects and facility differences. Half-model effects were further studied with use of floor blowing to change boundary layer profile and assess effects on model aerodynamics. Flow visualization data were gathered with fluorescent mini-tufts and UV oil. Finally, test time was spend working on the development of new Particle Image Velocimetry (PIV) and Model Deformation Measurement (MDM) capabilities at the 5mWT facility.

Ashley Evans↗

Assessment of RANS-based Transition Models based on Experimental Data of the Common Research Model with Natural Laminar Flow

Transition models based on auxiliary transport equations augmenting the Reynolds-averaged Navier-Stokes (RANS) framework often rely upon transition correlations that were derived from a limited number of low-speed experiments and these models often fail to account for all of the relevant transition mechanisms and/or the variation in those mechanisms with respect to changes in the significant flow parameters. Available data from a recent experiment on the Common Research Model with Natural Laminar Flow (CRM-NLF) in the National Transonic Facility at the NASA Langley Research Center are used to assess the current transition modeling capability in NASA's OVERFLOW 2.3b solver for a swept wing configuration with nonzero taper and transonic cruise conditions. Specifically, the OVERFLOW solutions are used to evaluate the accuracy and robustness of the transport-equation-based transition models. Results highlight that the Spalart-Allmaras-based amplification factor transport (AFT-2017b) equation model and Menter’s shear-stress transport equation (SST2003)-based Langtry-Menter transition models (either with or without the modeling of crossflow transition) significantly underpredict the reported extent of laminar flow region over the entire span of the wing, irrespective of which instability mechanism(s) is expected to dominate the onset of the transition process. We show that the transition correlations underlying these models fail to account for the stabilizing effect of compressibility on the Tollmien-Schlichting transition, which is likely to be a major contributor to the underprediction of the laminar flow region on the CRM-NLF. The SST-2003-based Langtry-Menter model also appears to inaccurately predict the chordwise pressure variation along the majority of the wing span at all the flow conditions studied herein, due to how the turbulence intensity levels were enforced in the computations and how that was interfering with the functioning of the underlying turbulence model within the boundary layer. The AFT and Langtry-Menter models appear to be sensitive to the level of the freestream turbulence intensity, but the degree of sensitivity varies across the models.

CFD modeling↗

Real-Time Drag Optimization of Aspect Ratio 13.5 Common Research Model with Distributed Flap System

This paper presents a real-time drag optimization study of the aspect ratio 13.5 Common Research Model (CRM) with a distributed mini-plain flap system. A surrogate aerodynamic model of the aspect ratio 13.5 CRM is developed based on an aerodynamic database computed by a transonic panel method to capture the aerodynamic coefficients as functions of the angle of attack, flap deflections, and Mach number. A recursive least-squares parameter estimation algorithm is designed to estimate the aerodynamic parameters of the surrogate model. The estimated surrogate model is then used in an on-line drag optimization strategy based on an adjoint method. The results of the real-time drag optimization indicate a drag reduction of 2.46% for Mach 0.80, 3.37% for Mach 0.85, and 1.95% for Mach 0.88. The results show the convergence of all parameter estimates.

Drag Optimization↗

Multiscale Mesh Adaptation for Transonic Aeroelastic Flutter Problems

This work applies multiscale mesh adaptation with refine to reduce spatial discretization error of aeroelastic computational fluid dynamics (CFD) simulations. Benchmark flutter models, such as the pitch and plunge NACA64A-010 airfoil and the benchmark supercritical wing, are studied with both a linearized frequency-domain solver and time-marching CFD coupled to a modal structural solver in FUN3D. The undeformed NASA Common Research Model (CRM), an aeroelastic jig shape variant of the CRM, is also studied with the linearized frequency-domain approach. For these cases, the adaptation process converges to comparable flutter predictions to hand-generated meshes but with smaller node counts. However the additional disciplines of the linearized frequency-domain analysis, the mesh deformation, and the unsteady finite-volume solver create robustness challenges that need to be addressed before it can be applied as a fully automated process for complex transonic aeroelastic problems. In particular, negative volumes are observed to be an issue for FUN3D’s linear elasticity mesh deformation solver when moving the adapted meshes.

Aeroelasticity↗

Fully Coupled Aeroelastic Stability Analysis of Adaptive Shape Memory Alloy Structural Technologies for Airframe Noise Reduction

This final report documents work performed by ATA Engineering, Inc., (ATA) to develop computational models and analyze the coupled fluid-structure response of two types of noise treatments applied to the leading-edge-slat component of a high-lift system typical of modern transport aircraft. The first treatment is a slat-gap filler (SGF), which closes the gap between the suction surfaces of a deployed slat and an aircraft main wing, and the second treatment is a slat-cove filler (SCF), which replaces the recirculating flow on the slat cove with a surface that promotes flow attachment. The representative airframe chosen for this work was NASA’s High-Lift Common Research Model (CRM-HL) in a baseline high-lift configuration. Superelastic shape memory alloys (SMAs) have been identified as enabling materials for these structural treatments. Since the technology elements rely upon having a highly reconfigurable structure, designs were assessed for their static aeroelastic deflection as well as their dynamic aeroelastic stability using coupled computational fluid dynamics (CFD) and nonlinear computational structural dynamics (NL-CSD) tools. Specifically, fluid-structure interaction (FSI) problems were solved computationally using the CFD solver Loci/CHEM and the NL-CSD solver Abaqus. As a part of the overall project, a similar capability was implemented using the CFD solver FUN3D coupled to Abaqus, although that work is documented in a separate report and that FSI framework was not used to analyze any of NASA’s SGF and SCF configurations. The technical approach consisted of solving for the flow field around the entire vehicle using a global CFD model, followed by extraction of relevant local subdomain data for CFD and NL-CSD co-simulations. The SGF design was analyzed using both 2D and 3D co-simulations to predict quasi-static aeroelastic deformations and to assess dynamic aeroelastic stability, whereas the SCF was analyzed in 2D only. SGF static aeroelastic response predictions focused on characterizing the deformed shape, with maximum displacements predicted to be on the order of magnitude of the technology element panel thickness. SGF dynamic aeroelastic response predictions used Partial Floquet analysis of the temporal evolution of selected nodal displacements to quantify the sign and magnitude of aeroelastic damping. Results suggest that the CRM-HL operating conditions would result in a dynamically stable response. The simulated dynamic pressure was also increased up to a factor of about four, and resulting responses suggest that predicted dynamic stability would be achieved with some margin.

Fluid Structure Interaction↗

HLPW-4/GMGW-3: Overview and Workshop Summary

The Fourth AIAA CFD High Lift Prediction Workshop and the Third Geometry and Mesh Generation Workshop were held collaboratively with the common goal of assessing the numerical prediction capability of current-generation computational fluid dynamics (CFD) technology for swept, medium/high-aspect-ratio wings in high-lift configurations. A key aspect of this joint endeavor was the use of Technology Focus Groups, an innovative new approach for workshops involving close collaboration between participants. These groups, which included both mesh generation and flow solver experts, worked to accelerate advancements for their particular methodologies by addressing key questions of importance {\em prior} to the workshop. The high-lift version of the NASA Common Research Model (CRM-HL) configuration was the focus of this workshop. Measured experimental wind tunnel data were available for comparison. The workshop also included a two-dimensional turbulence model verification exercise based on the CRM-HL wing shape. Altogether, 44 participants submitted a total of 184 data sets of CFD results. This paper provides a high-level summary of the results and conclusions from the workshop. Like at past workshops, fixed-grid Reynolds-averaged Navier-Stokes continued to be inaccurate and inconsistent for high lift. However, mesh adaptation definitively brought more consistency. Scale-resolving methods appeared most promising for predicting high-lift flow physics.

Christopher L Rumsey↗

On the Alleviation of Background Noise for the High-Lift Common Research Model Aeroacoustic Test

Microphone array measurements of the airframe noise from the High-Lift Common Research Model (CRM-HL) in the NASA Langley 14- by 22- Foot Subsonic Tunnel were initially hindered by extraneous noise sources. The steps taken to reduce the background noise in the open-jet test section for the aeroacoustic test are described in this paper. Adhesive-backed felt was used to attenuate noise resulting from the interaction of the test section shear layer with the collector and diffuser surfaces, scrubbing noise from the floor perforated panels, as well as an extraneous noise source produced near the junction of the model and the floor when the model was producing significant lift. The effects of the felt on noise attenuation and acoustic reflections are discussed. Following the CRM-HL test, scrubbing noise measurements from a floor basket with a perforated top panel were acquired in the Quiet Flow Facility to compare the performance of different perforated panel covers and their respective effects on the noise spectra. Aside from a smooth, hard wall, the felt cover was found to produce the minimum scrubbing noise of all the materials tested.

background noise↗