SEARCH · Search NASA

Results for “Case Reports”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

All sources NASA NTRS DOE OSTI

NASA NTRS2020

Sensor Chip Assembly (SCA) Test Report

This report summarizes the measured performance for the Sensor Chip Assembly (SCA), which is identified in Table 1. The SCA architecture is a substrate-removed HgCdTe detector with an area of 4096x4096 pixels (with a reference pixel area of four pixels deep around all four sides, available to substitute corresponding image pixels) and a pixel pitch of 10 μm. This SCA has been tested at the Goddard Space Flight Center (GSFC/NASA) Detector Characterization Laboratory (DCL). Teledyne (the vendor) classifies its detectors into different grades based on testing performed at its facility. The classification of this SCA and the tested dates are included in Table 1 below. The tests performed on this array are derived from the document WFIRST-PROC-09220_WFIRST-SCA-ATP_-.docx. A summary of the test parameters, requirements, and test results is presented in Table 2. The details of each test are subsequently described in the report. In the Summary (Table 2), SCA results are reported at an operating temperature of 95K, and 1.0 V bias voltage. In the detailed section of each test, the results for 90 K (1.0V bias voltage) and 95 K (0.5V bias voltage) are also reported. For all cases, the frame time used is 2.764 seconds. Reference pixel correction was applied to every raw frame.

WFIRST SCA TEST REPORT↗

NASA NTRS2019

Investigating Meteorological Conditions Associated with Valley Fever Outbreaks in Southwestern United States

According to CDC, a sharp increase in reported Valley fever cases (Coccidioidomycosis) has been found between 2009 and 2012. Environmental conditions play an important role for Valley fever outbreaks. For example, dust storms can significantly increase the amount of the fungus Coccidioides in the air and associated strong winds can transport the fungus to other areas. In last year’s AGU session, we reported a preliminary study to investigate hydrometeorological conditions and their connection with dust storm activities in southwestern United States. We found wind is a major contributing factor for the seasonal variation of dust storm activities. Interannual variation of the regional hydrometeorological conditions are closely linked to the large-scale environment such as the Pacific Decadal Oscillation (PDO). Strong winds are linked with a number of weather events such cold front passages, thunderstorms that produce downbursts and strong winds, the Santa Ana winds, etc. In this presentation, we will report the results of our latest investigation on meteorological conditions associated with Valley fever outbreaks in southwestern United States, using NLDAS (North American Land Data Assimilation System), GPM (Global Precipitation Measurement), and MERRA-2 (Modern Era Retrospective-analysis for Research and Applications, Version 2) hourly datasets, from the NASA Goddard Earth Sciences (GES) Data and Information Services Center (DISC).

Liu, Zhong↗

NASA NTRS1992

TRAC performance estimates

This report documents the performance characteristics of a Targeting Reflective Alignment Concept (TRAC) sensor. The performance will be documented for both short and long ranges. For long ranges, the sensor is used without the flat mirror attached to the target. To better understand the capabilities of the TRAC based sensors, an engineering model is required. The model can be used to better design the system for a particular application. This is necessary because there are many interrelated design variables in application. These include lense parameters, camera, and target configuration. The report presents first an analytical development of the performance, and second an experimental verification of the equations. In the analytical presentation it is assumed that the best vision resolution is a single pixel element. The experimental results suggest however that the resolution is better than 1 pixel. Hence the analytical results should be considered worst case conditions. The report also discusses advantages and limitations of the TRAC sensor in light of the performance estimates. Finally the report discusses potential improvements.

Everett, L.↗

NASA NTRS2014

Formal Methods Case Studies for DO-333

RTCA DO-333, Formal Methods Supplement to DO-178C and DO-278A provides guidance for software developers wishing to use formal methods in the certification of airborne systems and air traffic management systems. The supplement identifies the modifications and additions to DO-178C and DO-278A objectives, activities, and software life cycle data that should be addressed when formal methods are used as part of the software development process. This report presents three case studies describing the use of different classes of formal methods to satisfy certification objectives for a common avionics example - a dual-channel Flight Guidance System. The three case studies illustrate the use of theorem proving, model checking, and abstract interpretation. The material presented is not intended to represent a complete certification effort. Rather, the purpose is to illustrate how formal methods can be used in a realistic avionics software development project, with a focus on the evidence produced that could be used to satisfy the verification objectives found in Section 6 of DO-178C.

Cofer, Darren↗

NASA NTRS1991

Flares on Mira stars?

Fourteen cases of flares reported on Mira type stars have been collected. These flares typically have an amplitude of over half a magnitude, a rise time of minutes, and a duration of tens of minutes. Nine of the 11 stars represent a normal cross section of the Mira population, while the remaining two are in symbiotic systems (CH Cyg and RX Pup). The flares were observed photographically (five cases), photometrically (three cases), visually (three cases), and with radio telescopes (two cases), while CH Cyg has had flares observed by many techniques. The evidence for the existence of flares on Miras is strong but not definitive. It is possible to hypothesize a variety of background or instrumental effects that could explain all 14 events; however, there is no evidence that suggests the data should be taken at other than face value, and there are good arguments for rejecting the possibility of artifacts. It is felt that the current data warrant systematic observational and theoretical investigation of the possibility of flares on Mira stars.

Schaefer, Bradley E.↗

NASA NTRS1993

Excitation cross sections for the ns 2S yields np 2P resonance transitions in Mg(+) (n = 3) and Zn(+) (n = 4) using electron-energy-loss and merged-beams methods

Electron-excitation cross sections are reported for the 3s 2S yields 3p 2P(h, k) resonance transition in Mg(+) at energies from threshold (4.43 eV) to approximately 9 times threshold (40.0 eV). The electron-energy-loss merged-beams technique used in these measurements is described in detail. In addition, the method of separating contributions of the elastically scattered (Coulomb) and the inelastically scattered electrons in the present Mg(+) case and previously reported Zn(+) results is described. Comparisons in the experimental energy range are made for Mg(+) with the two five-state close-coupling theoretical calculations carried out herein, and with other published close-coupling, distorted-wave, and semiempirical calculations. The present Mg(+) cross sections and Zn(+) cross sections from earlier measurements are tabulated.

Smith, Steven J.↗

NASA NTRS2020

Unified Analysis of Aerospace Structures through Implementation of Rapid Tools into a Stress Framework

Rapid structural analysis tools have become an important part of the design cycle for aerospace companies for the last several decades. As these tools have been developed over time, there is often little consideration for shared software infrastructure between the tools, which makes design and analysis cumbersome due to a lack of commonality in input and output data and reporting, as well as poor traceability of results. Under the Rapid Tools task of the Advanced Composites Consortium (ACC), four aerospace tools were recently implemented or enhanced in the HyperSizer stress framework and then evaluated by this consortium of industry and government organizations. The framework provides an automated software environment for executing the rapid tools for analysis and sizing, quantifying margins of safety for thousands of load cases, and generating reports in support of FAA certification. This paper describes the process by which the tools were enhanced or implemented in the stress framework under the ACC project, and the evaluation conducted by industry consortium members.

Craig S Collier↗

NASA NTRS1988

Convection effects in protein crystal growth

Protein crystals for X-ray diffraction study are usually grown resting on the bottom of a hanging drop of a saturated protein solution, with slow evaporation to the air in a small enclosed cell. The evaporation rate is controlled by hanging the drop above a reservoir of water, with its saturation vapor pressure decreased by a low concentration of a passive solute. The drop has a lower solute concentration, and its volume shrinks by evaporation until the molecular concentrations match. Protein crystals can also be grown from a seed crystal suspended or supported in the interior of a supersaturated solution. The main analysis of this report concerns this case because it is less complicated than hanging-drop growth. Convection effects have been suggested as the reason for the apparent cessation of growth at a certain rather small crystal size. It seeems that as the crystal grows, the number of dislocations increases to a point where further growth is hindered. Growth in the microgravity environment of an orbiting space vehicle has been proposed as a method for obtaining larger crystals. Experimental observations of convection effects during the growth of protein crystals have been reported.

Roberts, Glyn O.↗

NASA NTRS2006

Another Approach to Enhance Airline Safety: Using Management Safety Tools

The ultimate goal of conducting an accident investigation is to prevent similar accidents from happening again and to make operations safer system-wide. Based on the findings extracted from the investigation, the "lesson learned" becomes a genuine part of the safety database making risk management available to safety analysts. The airline industry is no exception. In the US, the FAA has advocated the usage of the System Safety concept in enhancing safety since 2000. Yet, in today s usage of System Safety, the airline industry mainly focuses on risk management, which is a reactive process of the System Safety discipline. In order to extend the merit of System Safety and to prevent accidents beforehand, a specific System Safety tool needs to be applied; so a model of hazard prediction can be formed. To do so, the authors initiated this study by reviewing 189 final accident reports from the National Transportation Safety Board (NTSB) covering FAR Part 121 scheduled operations. The discovered accident causes (direct hazards) were categorized into 10 groups Flight Operations, Ground Crew, Turbulence, Maintenance, Foreign Object Damage (FOD), Flight Attendant, Air Traffic Control, Manufacturer, Passenger, and Federal Aviation Administration. These direct hazards were associated with 36 root factors prepared for an error-elimination model using Fault Tree Analysis (FTA), a leading tool for System Safety experts. An FTA block-diagram model was created, followed by a probability simulation of accidents. Five case studies and reports were provided in order to fully demonstrate the usefulness of System Safety tools in promoting airline safety.

Lu, Chien-tsug↗

NASA NTRS1983

Observations of unusual structures of high-latitude stratospheric electric fields

The observation, by means of balloon-borne sensors, of three cases of unusual stratospheric electric field structures at high latitudes is reported. In all three cases a region of downward directed electric field is flanked by regions with upward field. In two out of the three cases, the central downward field is much stronger than the average fair weather field. The vertical current densities involved are less than 5 x 10 to the -11th A/sq m. These field structures are observed only about 0.5 percent of the time.

Madsen, M. M.↗

NASA NTRS1991

A comparative study of performance parameters of n(+)-p InP solar cells made by closed-ampoule sulfur diffusion into Cd- and Zn-doped p-type InP substrates

Preliminary results indicate that Cd-doped substrates are better candidates for achieving high efficiency solar cells fabricated by closed-ampoule sulfur (S) diffusion than Zn-doped substrates. The differences in performance parameters (i.e., 14.3 percent efficiency for Cd-doped vs. 11.83 percent in the case of Zn-doped substrates of comparable doping and etch pit densities) were explained in terms of a large increase in dislocation density as a result of S diffusion in the case of Zn-doped as compared to Cd-doped substrates. The In(x)S(y) and probably Zn(S) precipitates in the case of Zn-doped substrates, produce a dead layer which extends deep below the surface and strongly affects the performance parameters. It should be noted that the cells had an unoptimized single layer antireflective coating of SiO, a grid shadowing of 6.25 percent, and somewhat poor contacts, all contributing to a reduction in efficiency. It is believed that by reducing the external losses and further improvement in cell design, efficiencies approaching 17 percent at 1 AMO, 25 degrees should be possible for cells fabricated on these relatively high defect density Cd-doped substrates. Even higher efficiencies, 18 to 19 percent should be possible by using long-lifetime substrates and further improving front surface passivation. If solar cells fabricated on Cd-doped substrates turn out to have comparable radiation tolerance as those reported in the case of cells fabricated on Zn-doped substrates, then for certain space missions 18 to 19 percent efficient cells made by this method of fabrication would be viable.

Faur, Mircea↗

NASA NTRS2000

Test Cases for a Rectangular Supercritical Wing Undergoing Pitching Oscillations

Steady and unsteady measured pressures for a Rectangular Supercritical Wing (RSW) undergoing pitching oscillations have been presented. From the several hundred compiled data points, 27 static and 36 pitching oscillation cases have been proposed for computational Test Cases to illustrate the trends with Mach number, reduced frequency, and angle of attack. The wing was designed to be a simple configuration for Computational Fluid Dynamics (CFD) comparisons. The wing had an unswept rectangular planform plus a tip of revolution, a panel aspect ratio of 2.0, a twelve per cent thick supercritical airfoil section, and no twist. The model was tested over a wide range of Mach numbers, from 0.27 to 0.90, corresponding to low subsonic flows up to strong transonic flows. The higher Mach numbers are well beyond the design Mach number such as might be required for flutter verification beyond cruise conditions. The pitching oscillations covered a broad range of reduced frequencies. Some early calculations for this wing are given for lifting pressure as calculated from a linear lifting surface program and from a transonic small perturbation program. The unsteady results were given primarily for a mild transonic condition at M = 0.70. For these cases the agreement with the data was only fair, possibly resulting from the omission of viscous effects. Supercritical airfoil sections are known to be sensitive to viscous effects (for example, one case cited). Calculations using a higher level code with the full potential equations have been presented for one of the same cases, and with the Euler equations. The agreement around the leading edge was improved, but overall the agreement was not completely satisfactory. Typically for low-aspect-ratio rectangular wings, transonic shock waves on the wing tend to sweep forward from root to tip such that there are strong three-dimensional effects. It might also be noted that for most of the test, the model was tested with free transition, but a few points were taken with an added transition strip for comparison. Some unpublished results of a rigid wing of the same airfoil and planform that was tested on the pitch and plunge apparatus mount system (PAPA) showed effects of the lower surface transition Strip on flutter at the lower subsonic Mach numbers. Significant effects of a transition strip were also obtained on a wing with a thicker supercritical section on the PAPA mount system. Both of these flutter tests on the PAPA resulted in very low reduced frequencies that may be a factor in this influence of the transition strip. However, these results indicate that correlation studies for RSW may require some attention to the estimation of transition location to accurately treat viscous effects. In this report several Test Cases are selected to illustrate trends for a variety of different conditions with emphasis on transonic flow effects. An overview of the model and tests is given and the standard formulary for these data is listed. Sample data points are presented in both tabular and graphical form. A complete tabulation and plotting of all the Test Cases is given. Only the static pressures and the real and imaginary parts of the first harmonic of the unsteady pressures are available. All the data for the test are available in electronic file form. The Test Cases are also available as separate electronic files.

Bennett, Robert M.↗

NASA NTRS1971

The reduction of a ""safety catastrophic'' potential hazard: A case history

A worst case analysis is reported on the safety of time watch movements for triggering explosive packages on the lunar surface in an experiment to investigate physical lunar structural characteristics through induced seismic energy waves. Considered are the combined effects of low pressure, low temperature, lunar gravity, gear train error, and position. Control measures constitute a seal control cavity and design requirements to prevent overbanking in the mainspring torque curve. Thus, the potential hazard is reduced to safety negligible.

Joseph P. Jones↗

NASA NTRS1972

Telemetry in animal and human biometeorology

Radio transmitters swallowed, surgically implanted, or carried externally make it possible to study a subject with minimum disturbance to normal patterns of activity. The radio frequency of transmission chosen will depend on the application, and will generally fall in the range from 50 kHz to 300 MHz. A number of specific experiments are reported, including the case of a snake which has swallowed a mouse containing a transmitter of pressure and temperature. Questions of monitoring are explored. Satellite Doppler tracking considerations are discussed together with the attachment of the transmitter package in the case of a study of birds.

Mackay, R. S.↗

NASA NTRS1976

Interaction between an elastic circular inclusion and two symmetrically placed collinear cracks

The paper investigates the fracture toughness of a flat large elastic cracked plate containing an elastic circular inclusion, using the plane stress crack-tip stress intensity factor as a criterion for fracture. In this plane stress geometry, each of the two collinear finite cracks is located on either side of the elastic circular inclusion and the geometry is subjected to uniform stresses at infinity. The analysis is based on the two-dimensional theory of elasticity by using the Muskhelishvili complex variable approach. Numerical calculations are reported for the case of simple tension normal to the crack direction and show the variation of the stress intensity factor with the configuration and elastic properties of the plate and the inclusion.

Hsu, Y. C.↗

NASA NTRS1978

Propagation of a laser beam in a time-varying waveguide

The propagation of an axisymmetric laser beam in a plasma column having a radially parabolic electron density distribution is reported. For the case of an axially uniform waveguide it is found that the basic characteristics of alternating focusing and defocusing beams are maintained. However, the intensity distribution is changed at the foci and outer-beam regions. The features of paraxial beam propagation are discussed with reference to axially varying waveguides. Laser plasma coupling is considered noting the case where laser heating produces a density distribution radially parabolic near the axis and the energy absorbed over the focal length of the plasma is small. It is found that: (1) beam-propagation stability is governed by the relative magnitude of the density fluctuations existing in the axial variation of the waveguides due to laser heating, and (2) for beam propagation in a time-varying waveguide, the global instability of the propagation is a function of the initial fluctuation growth rate as compared to the initial time rate of change in the radial curvature of the waveguide.

Chapman, J. M.↗

NASA NTRS1979

Process Feasibility Study in Support of Silicon Material, Task 1

During this reporting period, major activies were devoted to process system properties, chemical engineering and economic analyses. Analyses of process system properties was continued for materials involved in the alternate processes under consideration for solar cell grade silicon. The following property data are reported for silicon tetrafluoride: critical constants, vapor pressure, heat of varporization, heat capacity, density, surface tension, viscosity, thermal conductivity, heat of formation and Gibb's free energy of formation. Chemical engineering analysis of the BCL process was continued with primary efforts being devoted to the preliminary process design. Status and progress are reported for base case conditions; process flow diagram; reaction chemistry; material and energy balances; and major process equipment design.

Li, K. Y.↗

NASA NTRS1981

Modeling of growth and evaporation effects on the extinction of 1.0-micron solar radiation traversing stratospheric sulfuric acid aerosols

The effects of growth and evaporation of stratospheric sulfuric acid aerosols on the extinction of solar radiation traversing such an aerosol medium are reported for the case of 1.0-micron solar radiation. Modeling results show that aerosol extinction is not very sensitive to the change of ambient water vapor concentration, but is sensitive to ambient temperature changes, especially at low ambient temperatures and high ambient water vapor concentration. A clarification is given of the effects of initial aerosol size distribution and composition on the change of aerosol extinction due to growth and evaporation processes. It is shown that experiments designed to observe solar radiation extinction of aerosols may also be applied to the determination of observed changes in aerosol optical properties, environmental parameters, or the physical and optical characteristics of sulfate aerosols.

Yue, G. K.↗