Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computational geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Tidal stresses and energy gaps in microstate geometries

Here, we compute energy gaps and study infalling massive geodesic probes in the new families of scaling, microstate geometries that have been constructed recently and for which the holographic duals are known. We find that in the deepest geometries, which have the lowest energy gaps, the geodesic deviation shows that the stress reaches the Planck scale long before the probe reaches the cap of the geometry. Such probes must therefore undergo a stringy transition as they fall into microstate geometry. We discuss the scales associated with this transition and comment on the implications for scrambling in microstate geometries.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Experimental Flight Validation of the Prandtl 1933 Bell Spanload

This report describes the validation of the 1933 Prandtl bell spanload. This spanload is the minimum induced drag of a wing for a given structural weight with properties that eliminate adverse yaw. Aircraft using the Prandtl bell spanload were flown and investigated. The results of this research show that many previously held assumptions should be rethought, and the creation of aircraft using the Prandtl bell spanload will require considerable new techniques. Part of this work centered on the use of inverse methods. The usual first-step approach to a computational fluids problem is to create a geometry of the aircraft. Once this geometry exists, the computational fluids solution has been solved; however, the problem of creating the geometry still exists. A very small segment of the computational fluids world has concentrated on inverse solutions. This design approach begins with an end result - the computational fluids solution; from this end result, the geometry is sought. A more generic inverse tool was desired that would allow for the design of wings - specifically Prandtl bell spanload wings. Such a tool has been developed and allows for variable taper, aspect ratio, sweep, airfoils, and design-lift coefficients; output from the tool results in twist distribution of wings.

Albion H. Bowers↗

A Monte Carlo implementation of the predictor-corrector Quasi-Static method

The Quasi-Static method (QS) is a useful tool for solving reactor transients since it allows for larger time steps when updating neutron distributions. Because of the beneficial attributes of Monte Carlo (MC) methods (exact geometries and continuous energy treatment), it is desirable to develop a MC implementation for the QS method. In this work, the latest version of the QS method known as the Predictor-Corrector Quasi-Static method is implemented. Experiments utilizing two energy-groups provide results that show good agreement with analytical and reference solutions. The method as presented can easily be implemented in any continuous energy, arbitrary geometry, MC code. (authors)

97 MATHEMATICS AND COMPUTING↗

A wave-envelope of sound propagation in nonuniform circular ducts with compressible mean flows

An acoustic theory is developed to determine the sound transmission and attenuation through an infinite, hard-walled or lined circular duct carrying compressible, sheared, mean flows and having a variable cross section. The theory is applicable to large as well as small axial variations, as long as the mean flow does not separate. The technique is based on solving for the envelopes of the quasi-parallel acoustic modes that exist in the duct instead of solving for the actual wave, thereby reducing the computation time and the round-off error encountered in purely numerical techniques. The solution recovers the solution based on the method of multiple scales for slowly varying duct geometry. A computer program was developed based on the wave-envelope analysis for general mean flows. Results are presented for the reflection and transmission coefficients as well as the acoustic pressure distributions for a number of conditions: both straight and variable area ducts with and without liners and mean flows from very low to high subsonic speeds are considered.

Nayfeh, A. H.↗

Transonic Navier-Stokes flow computations over wing-fuselage geometries

The steady-state transonic viscous flows over two wing-fuselage configurations are solved numerically. The 3D compressible thin-layer Navier-Stokes equations are solved by means of multistage timestepping similar to the Runge-Kutta method. The timestepping technique is applied with a multigrid scheme to make the transonic Navier-Stokes computations using the Baldwin-Lomax turbulence for closure and converging the solution on a grid of 1.52 million grid points with a C-O topology. Both generic and fighter wing-fuselage geometries are solved, and the results are compared to experimental studies. Solution convergence is found to be fast, and the fine grid generates accurate results for both configurations by means of the Baldwin-Lomax turbulence model. Results from the Johnson-King model calculations produce results that are more consistent with experimental results for the fighter configuration.

Agrawal, S.↗

A computer program for calculating the perfect gas inviscid flow field about blunt axisymmetric bodies at an angle of attack of 0 deg

A method for the rapid calculation of the inviscid shock layer about blunt axisymmetric bodies at an angle of attack of 0 deg has been developed. The procedure is of an inverse nature, that is, a shock wave is assumed and calculations proceed along rays normal to the shock. The solution is iterated until the given body is computed. The flow field solution procedure is programed at the Langley Research Center for the Control Data 6600 computer. The geometries specified in the program are sphores, ellipsoids, paraboloids, and hyperboloids which may conical afterbodies. The normal momentum equation is replaced with an approximate algebraic expression. This simplification significantly reduces machine computation time. Comparisons of the present results with shock shapes and surface pressure distributions obtained by the more exact methods indicate that the program provides reasonably accurate results for smooth bodies in axisymmetric flow. However, further research is required to establish the proper approximate form of the normal momentum equation for the two-dimensional case.

Zoby, E. V.↗

Turbulent flow calculations using unstructured and adaptive meshes

A method of efficiently computing turbulent compressible flow over complex two dimensional configurations is presented. The method makes use of fully unstructured meshes throughout the entire flow field, thus enabling the treatment of arbitrarily complex geometries and the use of adaptive meshing techniques throughout both viscous and inviscid regions of the flow field. Mesh generation is based on a locally mapped Delaunay technique in order to generate unstructured meshes with highly-stretched elements in the viscous regions. The flow equations are discretized using a finite element Navier-Stokes solver, and rapid convergence to steady-state is achieved using an unstructured multigrid algorithm. Turbulence modeling is performed using an inexpensive algebraic model, implemented for use on unstructured and adaptaive meshes. Compressible turbulent flow solutions about multiple-element airfoil geometries are computed and compared with expeirmental data.

Mavriplis, Dimitri J.↗

Turbulent flow calculations using unstructured and adaptive meshes

A method of efficiently computing turbulent compressible flow over complex two dimensional configurations is presented. The method makes use of fully unstructured meshes throughout the entire flow-field, thus enabling the treatment of arbitrarily complex geometries and the use of adaptive meshing techniques throughout both viscous and inviscid regions of flow-field. Mesh generation is based on a locally mapped Delaunay technique in order to generate unstructured meshes with highly-stretched elements in the viscous regions. The flow equations are discretized using a finite element Navier-Stokes solver, and rapid convergence to steady-state is achieved using an unstructured multigrid algorithm. Turbulence modeling is performed using an inexpensive algebraic model, implemented for use on unstructured and adaptive meshes. Compressible turbulent flow solutions about multiple-element airfoil geometries are computed and compared with experimental data.

Mavriplis, Dimitri J.↗

Preliminary Assessment of ATR-C Capabilities to Provide Integral Benchmark Data for Key Structural/Matrix Materials that May be Used for Nuclear Data Testing and Analytical Methods Validation

The purpose of this document is to identify some suggested types of experiments that can be performed in the Advanced Test Reactor Critical (ATR-C) facility. A fundamental computational investigation is provided to demonstrate possible integration of experimental activities in the ATR-C with the development of benchmark experiments. Criticality benchmarks performed in the ATR-C could provide integral data for key matrix and structural materials used in nuclear systems. Results would then be utilized in the improvement of nuclear data libraries and as a means for analytical methods validation. It is proposed that experiments consisting of well-characterized quantities of materials be placed in the Northwest flux trap position of the ATR-C. The reactivity worth of the material could be determined and computationally analyzed through comprehensive benchmark activities including uncertainty analyses. Experiments were modeled in the available benchmark model of the ATR using MCNP5 with the ENDF/B-VII.0 cross section library. A single bar (9.5 cm long, 0.5 cm wide, and 121.92 cm high) of each material could provide sufficient reactivity difference in the core geometry for computational modeling and analysis. However, to provide increased opportunity for the validation of computational models, additional bars of material placed in the flux trap would increase the effective reactivity up to a limit of 1$ insertion. For simplicity in assembly manufacture, approximately four bars of material could provide a means for additional experimental benchmark configurations, except in the case of strong neutron absorbers and many materials providing positive reactivity. Future tasks include the cost analysis and development of the experimental assemblies, including means for the characterization of the neutron flux and spectral indices. Oscillation techniques may also serve to provide additional means for experimentation and validation of computational methods and acquisition of integral data for improving neutron cross sections. Further assessment of oscillation techniques for implementation in the ATR-C may be of additional benefit. The establishment of benchmark experiment capabilities in the ATR-C would allow for the further development of techniques and facility enhancements involving neutronics experimentation in the ATR-C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Final Report for "Tech-X Corporation work for the SciDAC Center for Simulation of RF Wave Interactions with Magnetohydrodynamics (SWIM)"

Work carried out by Tech-X Corporation for the DoE SciDAC Center for Simulation of RF Wave Interactions with Magnetohydrodynamics (SWIM; U.S. DoE Office of Science Award Number DE-FC02-06ER54899) is summarized and is shown to fulfil the project objectives. The Tech-X portion of the SWIM work focused on the development of analytic and computational approaches to study neoclassical tearing modes and their interaction with injected electron cyclotron current drive. Using formalism developed by Hegna, Callen, and Ramos [Phys. Plasmas 16, 112501 (2009); Phys. Plasmas 17, 082502 (2010); Phys. Plasmas 18, 102506 (2011)], analytic approximations for the RF interaction were derived and the numerical methods needed to implement these interactions in the NIMROD extended MHD code were developed. Using the SWIM IPS framework, NIMROD has successfully coupled to GENRAY, an RF ray tracing code; additionally, a numerical control system to trigger the RF injection, adjustment, and shutdown in response to tearing mode activity has been developed. We discuss these accomplishments, as well as prospects for ongoing future research that this work has enabled (which continue in a limited fashion under the SciDAC Center for Extended Magnetohydrodynamic Modeling (CEMM) project and under a baseline theory grant). Associated conference presentations, published articles, and publications in progress are also listed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

GENIE(++): A Multi-Block Structured Grid System

The computer code GENIE++ is a continuously evolving grid system containing a multitude of proven geometry/grid techniques. The generation process in GENIE++ is based on an earlier version. The process uses several techniques either separately or in combination to quickly and economically generate sculptured geometry descriptions and grids for arbitrary geometries. The computational mesh is formed by using an appropriate algebraic method. Grid clustering is accomplished with either exponential or hyperbolic tangent routines which allow the user to specify a desired point distribution. Grid smoothing can be accomplished by using an elliptic solver with proper forcing functions. B-spline and Non-Uniform Rational B-splines (NURBS) algorithms are used for surface definition and redistribution. The built in sculptured geometry definition with desired distribution of points, automatic Bezier curve/surface generation for interior boundaries/surfaces, and surface redistribution is based on NURBS. Weighted Lagrance/Hermite transfinite interpolation methods, interactive geometry/grid manipulation modules, and on-line graphical visualization of the generation process are salient features of this system which result in a significant time savings for a given geometry/grid application.

Williams, Tonya↗

Application of Computer Axial Tomography (CAT) to measuring crop canopy geometry

The feasibility of using the principles of computer axial topography (CAT) to quantify the structure of crop canopies was investigated because six variables are needed to describe the position-orientation with time of a small piece of canopy foliage. Several cross sections were cut through the foliage of healthy, green corn and soybean canopies in the dent and full pod development stages, respectively. A photograph of each cross section representing the intersection of a plane with the foliage was enlarged and the air-foliage boundaries delineated by the plane were digitized. A computer program was written and used to reconstruct the cross section of the canopy. The approach used in applying optical computer axial tomography to measuring crop canopy geometry shows promise of being able to provide needed geometric information for input data to canopy reflectance models. The difficulty of using the CAT scanner to measure large canopies of crops like corn is discussed and a solution is proposed involving the measurement of plants one at a time.

Bauer, M. E.↗

Detector alignment for X-ray crystallography using Millepede-II

I describe a method for accurately refining the geometrical parameters of segmented X-ray area detectors on the basis of serial crystallography data, using 'Millepede' – an algorithm created for a very similar problem in high-energy physics. The Millepede method for serial crystallography builds on the approach of Brewster et al. [Acta Cryst. (2018), D74, 877–894], in which the detector parameters are refined simultaneously with the parameters for each individual crystal. This accounts for the mutual dependency between the parameters and thereby avoids the bias and slow convergence problems that have afflicted older approaches in which the deviations between observed and calculated Bragg peak positions were taken directly as the updates for the detector panel positions. The Millepede method uses the special structure of the least-squares normal equations to reduce them to a much smaller form that can be solved very quickly, even compared with the sparse matrix methods used previously. This makes it practical to refine the detector geometry frequently and thereby maintain accurate calibration without specialized alignment campaigns. Tilts of detector panels out of the plane can be reliably refined, as can the overall distance of the detector in the beam direction. With a simulated test case, the new method produced panel shifts within 7% of the correct values with only one iteration, and produced almost exactly correct shifts after a second iteration. A simulated out-of-plane panel rotation was correctly determined to within 0.001°. Applied to experimental data from an X-ray free-electron laser, the method increased the indexable fraction of frames from 30% to 91% in a single iteration, and to 96% after two further iterations. Computing the geometry updates on the basis of 2060 crystals took only 0.819 s on desktop computing hardware, including the time taken to read the required data from disk. The scaling was found to be very close to linear for up to 100 980 sets of crystal parameters, which took only 78.2 s to process under the same conditions. The method has been applied as part of a real-time feedback system at a synchrotron radiation beamline, in which an out-of-plane detector tilt of 0.04° was detected and corrected. Possible further applications are also described here.

Millepede-II↗

Highly parallel structured adaptive mesh refinement using parallel language-based approaches

Adaptive mesh refinement (AMR) calculations carried out on structured meshes play an exceedingly important role in several areas of science and engineering. A strategy for using Fortran 90 in an object-oriented fashion is presented. This permits AMR applications to be expressed in terms of familiar abstractions that are natural to the process of solving AMR hierarchies. The OpenMP features that are useful for parallel processing of AMR hierarchies in a load balanced fashion on multiprocessors is described.

computational↗

An Investigation of High-Order Shock-Capturing Methods for Computational Aeroacoustics

Topics covered include: Low-dispersion scheme for nonlinear acoustic waves in nonuniform flow; Computation of acoustic scattering by a low-dispersion scheme; Algorithmic extension of low-dispersion scheme and modeling effects for acoustic wave simulation; The accuracy of shock capturing in two spatial dimensions; Using high-order methods on lower-order geometries; and Computational considerations for the simulation of discontinuous flows.

Casper, Jay↗

PBW Degeneration: Algebra, Geometry, and Combinatorics

We review the recent progress in the theory of Poincaré–Birkhoff–Witt degenerations of irreducible representations of simple Lie algebras. We describe algebraic, geometric, and combinatorial aspects of the theory.

97 MATHEMATICS AND COMPUTING↗

NASA HECC Geometry and Performance Review Part 1: Validation of a Computational Model for the Vaneless Diffuser Configuration with As-Manufactured Impeller Geometry

An investigation of the NASA High Efficiency Centrifugal Compressor (HECC) vaneless diffuser configuration was performed. This multipart investigation presents an extensive validation of the computational model against experimental data. The validated model was then used to explore the effects geometric differences between the as-manufactured and design-intent impellers. Lastly, the validated model was used for comparison against an experimental tip clearance study. Part I of the investigation focused on describing the HECC vaneless computational model and its validation against the experimental data published in GT2023-103128. To generate the model, a verification of the manufactured impeller was performed and was confirmed to match the impeller CAD. Section data from the impeller CAD, referred to as the As-Manufactured geometry, were used for development of the computational model. Steady RANS simulations utilizing the Wilcox K-Omega 98 turbulence model and a multiblock structured mesh were used to conduct a mesh convergence study. The resultant mesh was then used for simulations at both design-speed and off-design speed conditions. The simulations compared well to data in both 1D and 2D terms for the major performance metrics of efficiency, total pressure rise, and total temperature rise. Based on the observed results the model was deemed validated and was used in the latter two parts of the multipart investigation.

centrifugal compressor↗

Assessment of Automated Fiber Placement for the Fabrication of Composite Wind Tunnel Blades

Composite wind tunnel blades are frequently fabricated by hand layup of prepreg fabrics. Though well proven, this fabrication method is laborious and expensive. The study described in this paper used the Integrated Structural Assembly of Advanced Composites (ISAAC) facility at the NASA Langley Research Center to explore whether automated fiber placement (AFP) could reduce manufacturing time and cost for production of wind tunnel blades. Two blades, taken from two NASA wind tunnels, were investigated as representative geometries. Computer-aided design models of the blade surfaces were created, and AFP process planning and programming were employed to study the manufacturability of the shapes. A placement/cure tool was manufactured for the chosen blade surface from thermoplastic material using an additive manufacturing process. The present study revealed that the AFP head geometry, primarily the heater configuration of the ISAAC system, is the primary constraint that limits the ability to manufacture the selected wind tunnel fan blades using AFP.

Grenoble, Ray↗