Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cu formate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

High-throughput investigation of crystal-to-glass transformation of Ti–Ni–Cu ternary alloy

A high-throughput investigation of metallic glass formation via solid-state reaction was reported in this paper. Combinatorial multilayered thin-film chips covering the entire Ti-Ni-Cu ternary system were prepared using ion beam sputtering technique. Microbeam synchrotron X-ray diffraction (XRD) and X-ray fluorescence (XRF) measurements were conducted, with 1,325 data points collected from each chip, to map out the composition and the phase constitution before and after annealing at 373 K for 110 hours. The composition dependence of the crystal-to-glass transition by solid-state reaction was surveyed using this approach. The resulting composition-phase map is consistent with previously reported results. Time-of-flight secondary ion mass spectroscopy (ToF-SIMS) was performed on the representative compositions to determine the inter-diffusion between layers, the result shows that the diffusion of Ti is the key factor for the crystal-to-glass transition. In addition, both layer thickness and layer sequence play important roles as well. This work demonstrates that combinatorial chip technique is an efficient way for systematic and rapid study of crystal-to-glass transition for multi-component alloy systems.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Superconducting Bi1.5Pb0.5Sr2Ca2Cu3O(x) ceramics by rapid melt quenching and glass crystallization

A glass of nominal Bi(1.5)Pb(0.5)Sr2Ca2Cu3O(x) composition, prepared by rapid quenching of the melt, showed a glass transition temperature of 383 C, crystallization temperature of 446 C, melting temperature of 855 C, and bulk density of 5.69 g/cu cm in air. The activation energy for crystallization of the glass was estimated to be 292kJ/mol from non-isothermal DSC. On heating in oxygen, the glass showed a slow and continuous weight gain starting at approximately 530 C which reached a plateau at approximately 820 C. The weight gained during heating was retained on cooling to ambient conditions indicating an irreversible oxidation step. The influence of annealing conditions on the formation of various phases in the glass has been investigated. The Bi(2)Sr(2)Ca(0)Cu(1)O(6) phase crystallized out first followed by formation of other phases at higher temperatures. The high-T(sub c) phase, isostructural with Bi(2)Sr(2)Ca(2)Cu(3)O(10) was not detected below 840 C, but its fraction increased with the annealing time at 840 C. A sample annealed at 840 C for 243h in air and furnace cooled showed the highest T(sub c)(R=0) of 107.2K and a narrow transition width, delta T(sub c)(10 to 90 percent), of approximately 2 K. The high T(sub c) phase does not seem to crystallize out directly from the glass but is rather produced at high temperature by reaction between the phases formed at lower temperatures. The kinetics of 110K phase formation was sluggish. It appears that the presence of lead helps in the formation and/or stabilization of the 110 K phase.

Bansal, Narottam P.↗
DOE OSTI2023

Vortex Structure of Head Bubble in Convective Cloud Starting Plume

Abstract A developing cumulus cloud (Cu) was modeled, and dynamic, thermodynamic, and microphysical properties of an ascending head bubble reproducing the upper part of a developing Cu were investigated. The data for analysis are taken from 10-m-resolution LES of trade wind Cu under BOMEX conditions. The detection of a rising bubble is carried out using wavelet filtering of the velocity fields and microphysical fields, while a low-frequency signal of the filtering is associated with the convective-scale structure of cloud. We substantiate and discuss the representation of the bubble as a vortex ring, and estimate the parameters of this vortex ring. The simplest Hill’s vortex was chosen as a model of a vortex ring inside cloud. Analytical approximations of the radial profiles of the vertical velocity and of conservative quantities (such as total water mixing ratio and liquid water potential temperature inside and outside the bubble) are obtained. The spatial structure of these quantities is investigated using analytical expressions. Analytical models for spatial distributions of liquid water content (LWC) and adiabatic fraction (AF) are also designed and analyzed. The results demonstrate the existence of a cloud core with high values of LWC and AF up to the height of 1800 m. The horizontally averaged value of the adiabatic fraction, calculated analytically using the Hill’s vortex concept, is evaluated as 0.39, which is the typical AF value in the upper parts of such Cu. The vertical profiles of different important quantities characterizing cloud structure are presented. The analysis performed in this study allows us to conclude that a rising vortex ring plays the dominating role in formation of the thermodynamic and microphysical structure of developing Cu. Significance Statement 1) Dynamic and thermodynamic fields of a developing cumulus cloud simulated by high-resolution LES with spectral bin microphysics are separated into convective and turbulent components by means of the wavelet technique. 2) The analysis of convective component of the cloud revealed the existence of a vortex ring at the developing stage of the cloud and evaluate its parameters. 3) The analysis performed in this study allows us to conclude that a rising vortex ring plays the important role in formation of the thermodynamic and microphysical structure of developing Cu. 4) The study provides a novel insight into the cloud–environment interaction. 5) The approximating equations describing the vortex ring can be usefully applied for developing new schemes of convective parameterization.

Meteorology & Atmospheric Sciences↗
DOE OSTI2022

Thermodynamics of the Metal Carbonates and Bicarbonates of Mn, Co, Ni, Cu, and Zn Relevant to Mineral Energetics

The gas phase heats of formation of ground-state MCO 3 , M(HCO 3 ) 2 , and M(HCO 3 )(OH), where M = Mn, Co, Ni, Cu, and Zn, have been predicted using the correlated molecular orbital theory at the CCSD(T) level extrapolated to the complete basis set limit using the Feller–Peterson–Dixon (FPD) approach. Cohesive energies of the carbonates were predicted based on the calculated gas phase and experimental solid heats of formation. Coulombic dissociation energies (CDEs) between metal cations and anions show a near-linear correlation with Shannon metal cation atomic radii, yet no correlation is found with the hardness of these cations. The total reaction dissociation energies (TRDEs) of transition metals are higher than their CDEs for the di-bicarbonates, in contrast to those for Mg and Ca based on our prior work. In addition to differences in the energies needed to prepare the transition metal dications, electron donation from the ligands to the 3d orbitals of open-shell transition metal dications from lone pairs of adjacent O atoms also plays a role. No electron donation from the ligands to the fully occupied 3d orbitals of Zn and Cd was found. Decomposition energies for generating MO, CO 2 , and/or H 2 O were calculated. Gas phase metal exchange energies only partially correlate with the electrochemical series for M(s) → M 2+( aq). The FPD heats of formation were used to benchmark a range of density functional theory exchange–correlation functionals, including those commonly used in solid-state mineral calculations. None of the functionals provided chemical accuracy agreement (±1 kcal/mol) with the FPD results. So, the best agreement with the FPD results is predicted for the $\tau$-HCTH functional with an average unsigned error of 8.3 kcal/mol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Direct observation of Mn distribution/speciation within and surrounding a basidiomycete fungus in the production of Mn-oxides important in toxic element containment

Biogenic manganese (Mn) oxides occur ubiquitously in the environment including the uranium (U) mill tailings at the Ningyo-toge U mine in Okayama, Japan, being important in the sequestration of radioactive radium (Ra). To understand the nanoscale processes in Mn oxides formation at the U mill tailings site, Mn 2+ absorption by a basidiomycete fungus, Coprinopsis urticicola, isolated from Ningyo-toge mine water samples, was investigated in the laboratory under controlled conditions utilizing electron microscopy, synchrotron-based X-ray analysis, and fluorescence microscopy with molecular pH probe. The fungus’ growth was first investigated in an agar-solidified medium supplemented with 1.0 mmol/L of Mn 2+ , ± Cu 2+ (50 – 200 µM), ± Zn 2+ (50 – 200 µM), or ± diphenyleneiodonium chloride (DPI) (50 – 100 µM) at 25 °C. The results revealed that Zn 2+ has no significant effects on the Mn oxides formation, whereas Cu 2+ and DPI significantly inhibit both fungal growth and Mn oxidation, indicating superoxide-mediated Mn oxidation. During the interaction of Mn 2+ with the fungi in solution medium at the initial pH of 5.67, a small fraction of Mn 2+ infiltrated into the fungal hyphae within 8 h, forming a few tens nm-sized concentrates of soluble Mn2+ in the intracellular pH of ~6.5, which can be released back to solution within a day as shown in a subsequent releasing experiment. After 1 day of incubation, Mn oxides began to precipitate on the hyphae, which were characterized to be fibrous nanocrystals with a hexagonal birnessite-structure, these forming spherical aggregates with a diameter of ~1.5 µm. When the fungi were reacted using the Ningyo-toge mine water, the Mn concentration decreased at a rate of 1.0 mmol·day-1 per unit dry weight. The nanoscale processes associated with the fungi derived from the Ningyo-toge mine area provides additional insights into the existing mechanisms of Mn oxidation by filamentous fungi at other U mill tailings sites under circumneutral pH conditions. Such processes add to the class of reactions important to the sequestration of toxic elements.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1979

Molecule formation and infrared emission in fast interstellar shocks. I Physical processes

The paper analyzes the structure of fast shocks incident upon interstellar gas of ambient density from 10 to the 7th per cu cm, while focusing on the problems of formation and destruction of molecules and infrared emission in the cooling, neutral post shock gas. It is noted that such fast shocks initially dissociate almost all preexisting molecules. Discussion covers the physical processes which determine the post shock structure between 10 to the 4 and 10 to the 2 K. It is shown that the chemistry of important molecular coolants H2, CO, OH, and H2O, as well as HD and CH, is reduced to a relatively small set of gas phase and grain surface reactions. Also, the chemistry follows the slow conversion of atomic hydrogen into H2, which primarily occurs on grain surfaces. The dependence of this H2 formation rate on grain and gas temperatures is examined and the survival of grains behind fast shocks is discussed. Post shock heating and cooling rates are calculated and an appropriate, analytic, universal cooling function is developed for molecules other than hydrogen which includes opacities from both the dust and the lines.

Hollenbach, D.↗
DOE OSTI2022

Experimental evidence of early-time saturation of the ion-Weibel instability in counterstreaming plasmas of CH, Al, and Cu

The collisionless ion-Weibel instability is a leading candidate mechanism for the formation of collisionless shocks in many astrophysical systems, where the typical distance between particle collisions is much larger than the system size. Multiple laboratory experiments aimed at studying this process utilize laser-driven (I≳10 15 W/cm 2 ), counterstreaming plasma flows (V≲ 2000 km/s) to create conditions unstable to Weibel-filamentation and growth. This technique intrinsically produces temporally varying plasma conditions at the midplane of the interaction where Weibel-driven B fields are generated and studied. Experiments discussed herein demonstrate robust formation of Weibel-driven B fields under multiple plasma conditions using CH, Al, and Cu plasmas. Linear theory based on benchmarked radiation-hydrodynamic FLASH calculations is compared with Fourier analyses of proton images taken ~5–6 linear growth times into the evolution. Our new analyses presented here indicate that the low-density, high-velocity plasma-conditions present during the first linear-growth time (~300–500 ps) sets the spectral characteristics of Weibel filaments during the entire evolution. It is shown that the dominant wavelength (~300 μm) at saturation persists well into the nonlinear phase, consistent with theory under these experimental conditions. However, estimates of B-field strength, while difficult to determine accurately due to the path-integrated nature of proton imaging, are shown to be in the ~10–30 T range, an order of magnitude above the expected saturation limit in homogenous plamas but consistent with enhanced B fields in the midplane due to temporally varying plasma conditions in experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Strain-rate dependent deformation mechanisms in single-layered Cu, Mo, and multilayer Cu/Mo thin films

Here, strain-rate sensitivity and rate-dependent hardness, over a range of 10 -2 to 10 2 s -1 , of sputter-deposited single-layered Cu, Mo, and 5 nm Cu/ 5 nm Mo, and 100 nm Cu/ 100 nm Mo multilayer films with a total film thickness of 5 μm were measured using nanoindentation. The plastic zone underneath the nanoindents was characterized via cross-sectional transmission electron microscopy (XTEM). The multilayer films exhibited enhanced hardness but slightly reduced strain-rate sensitivity with decreasing layer thickness from 100 nm to 5 nm. Only the 5 nm Cu/ 5 nm Mo multilayer film exhibited shear bands underneath the nanoindents, and the size of the shear bands increased with increasing strain rate. In contrast, the 100 nm Cu/ 100 nm Mo multilayer film exhibited material pile-up around the indents and significant nanotwinning within Cu grains. The effect of strain rate and layer thickness on the hardness and strain rate sensitivity of the multilayer thin films is interpreted using a modified confined layer slip (CLS) model. The reduced rate sensitivity at 5 nm as compared to 100 nm correlates with abundant growth nanotwins in the Cu grains in 100 nm and formation of shear bands in 5 nm multilayers. In single layer films, a substructure with a high density of dislocations was observed consistent with the plastic strain gradient in the indent plastic zone. No evidence of deformation twins was noted in any of the samples.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dynamic Copper Site Redispersion through Atom Trapping in Zeolite Defects

Single-site copper-based catalysts have shown remarkable activity and selectivity for a variety of reactions. However, deactivation by sintering in high-temperature reducing environments remains a challenge and often limits their use due to irreversible structural changes to the catalyst. Here, we report zeolite-based copper catalysts in which copper oxide agglomerates formed after reaction can be repeatedly redispersed back to single sites using an oxidative treatment in air at 550 °C. Under different environments, single-site copper in Cu–Zn–Y/deAlBeta undergoes dynamic changes in structure and oxidation state that can be tuned to promote the formation of key active sites while minimizing deactivation through Cu sintering. For example, single-site Cu 2+ reduces to Cu 1+ after catalyst pretreatment (270 °C, 101 kPa H 2 ) and further to Cu0 nanoparticles under reaction conditions (270–350 °C, 7 kPa EtOH, 94 kPa H 2 ) or accelerated aging (400–450 °C, 101 kPa H 2 ). After regeneration at 550 °C in air, agglomerated CuO was dispersed back to single sites in the presence and absence of Zn and Y, which was verified by imaging, in situ spectroscopy, and catalytic rate measurements. Ab initio molecular dynamics simulations show that solvation of CuO monomers by water facilitates their transport through the zeolite pore, and condensation of the CuO monomer with a fully protonated silanol nest entraps copper and reforms the single-site structure. Importantly, the capability of silanol nests to trap and stabilize copper single sites under oxidizing conditions could extend the use of single-site copper catalysts to a wider variety of reactions and allows for a simple regeneration strategy for copper single-site catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Plasmon excitations in chemically heterogeneous nanoarrays

The capability of collective excitations, such as localized surface plasmon resonances, to produce a versatile spectrum of optical phenomena is governed by the interactions within the collective and single-particle responses in the finite system. In many practical instances, plasmonic metallic nanoparticles and arrays are either topologically or chemically heterogeneous, which affects both the constituent transitions and their interactions. Here, the formation of collective excitations in weakly Cu- and Pd-doped Au nanoarrays is described using time-dependent density functional theory. The additional impurity-induced modes in the optical response can be thought to result from intricate interactions between separated excitations or transitions. In this work, we investigate the heterogeneity at the impurity level, the symmetry aspects related to the impurity position, and the influence of the impurity position on the confinement phenomena. The chemically rich and symmetry-dependent quantum mechanical effects are analyzed with transition contribution maps demonstrating the possibility to develop nanostructures with more controlled collective properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1988

Analytical study of He II flow characteristics in the SHOOT transfer line

Pressure and temperature profiles for He II flow in the transfer line for the Superfluid Helium On-Orbit Transfer (SHOOT) experiment are determined using a finite difference method to solve the one-dimensional two-fluid conservation equations. For practical purposes, forced flow of He II with Re greater than 10 to the 6th can be treated as a classical turbulent flow For a maximum SHOOT transfer rate of 800 cu dm/h, the temperature rise between the pump outlet and the receiver tank is about 80 mk with a 7-W heat load imposed on the 4-m-long transfer line. A pump outlet pressure of 160 torr is required to sustain the 800 cu dm/h flow without causing vapor formation within the transfer line.

Lee, J. H.↗
NASA NTRS1988

Influence of several metal ions on the gelation activation energy of silicon tetraethoxide

The effects of nine metal cations (Li(+), Na(+), Mg(2+), Ca(2+), Sr(2+), Cu(2+), Al(3+), La(3+), and Y(3+) on silica gel formation has been investigated by studying the hydrolysis and polycondensation of silicon tetraethoxide (TEOS) in the presence of metal nitrates. The influence of water: TEOS mole ratio, metal ion concentration, and the reaction temperature has been investigated. The overall activation energy for gel formation has been determined from the temperature dependence of the time of gelation for each system. The activation energy for -Si-O-Si- network formation is found to be 54.5 kJ/mol. The gel formation time as well as the activation energy sharply increase in the presence of Cu(2+), Al(3+), La(3+) and Y(3+). In contrast, the presence of Li(+), Na(+), Mg(2+), Ca(2+), or, Sr(2+) lowers the gelation time, but has no appreciable effect on the activation energy. This difference may be attributed to the participation or nonparticipation of the metal ions in the formation of the three-dimensional polymeric network during the polycondensation step. The concentration of metal ion (Mg(2+), Ca(2+), Y(3+) or the water: TEOS mole ratio had no appreciable effect on the gelation activation energy. A simple test has been proposed to determine whether a metal ion would act as a network intermediate or modifier in silica and other glassy networks.

Bansal, Narottam P.↗
NASA NTRS1990

Influence of several metal ions on the gelation activation energy of silicon tetraethoxide

The effects of nine metal cations Li(+), Na(+), Mg(2+), Ca(2+), Sr(2+), Cu(2+), Al(3+), La(3+), and Y(3+) on silica gel formation has been investigated by studying the hydrolysis and polycondensation of silicon tetraethoxide (TEOS) in the presence of metal nitrates. The influence of water:TEOS mole ratio, metal ion concentration, and the reaction temperature has been investigated. The overall activation energy for gel formation has been determined from the temperature dependence of the time of gelation for each system. The activation energy for -Si-O-Si- network formation is found to be 54.5 kJ/mol. The gel formation time as well as the activation energy sharply increase in the presence of Cu(2+), Al(3+), La(3+) and Y(3+). In contrast, the presence of Li(+), Na(+), Mg(2+), Ca(2+), or Sr(2+) lowers the gelation time, but has no appreciable effect on the activation energy. This difference may be attributed to the participation or nonparticipation of the metal ions in the formation of the three-dimensional polymeric network during the polycondensation step. The concentration of metal ion Mg(2+), Ca(2+), Y(3+) or the water:TEOS mole ratio had no appreaciable effect on the gelation activation energy. A simple test has been proposed to determine whether a metal ion would act as a network intermediate or modifier in silica and other glassy networks.

Bansal, Narottam P.↗
DOE OSTI2024

Divergent Bimetallic Mechanisms in Copper(II)-Mediated C–C, N–N, and O–O Oxidative Coupling Reactions

Copper-catalyzed aerobic oxidative coupling of diaryl imines provides a route for conversion of ammonia to hydrazine. Here the present study uses experimental and density functional theory computational methods to investigate the mechanism of N–N bond formation, and the data support a mechanism involving bimolecular coupling of Cu-coordinated iminyl radicals. Computational analysis is extended to Cu II -mediated C–C, N–N, and O–O coupling reactions involved in the formation of cyanogen (NC–CN) from HCN, 1,3-butadiyne from ethyne (i.e., Glaser coupling), hydrazine from ammonia, and hydrogen peroxide from water. The results reveal two different mechanistic pathways. Heteroatom ligands with an uncoordinated lone pair (iminyl, NH 2 , OH) undergo charge transfer to Cu II , generating ligand-centered radicals that undergo facile bimolecular radical–radical coupling. Ligands lacking a lone pair (CN and CCH) form bridged binuclear diamond-core structures that undergo C–C coupling. This mechanistic bifurcation is rationalized by analysis of spin densities in key intermediates and transition states, as well as multiconfigurational calculations. Radical–radical coupling is especially favorable for N–N coupling owing to energetically favorable charge transfer in the intermediate and thermodynamically favorable product formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

High-Temperature Oxidation Behavior of FeCoCrNi+(Cu/Al)-Based High-Entropy Alloys in Humid Air

Previous studies showed some transition metal high-entropy alloy (HEA) compositions can have good oxidation resistance in air up to 800 °C. Four equiatomic HEAs have been developed based on FeCoCrNi with additions of Mn, Cu, Al or Al+Cu. The oxidation behavior of these HEAs was compared in humid (10 vol.% H2O) air at 800 °C for 100–500 h to investigate the influence of water vapor on the oxidation mechanisms. The Cu- and Al-containing alloys exhibited improved oxidation resistance over the Mn composition. For the Cu-containing alloy, a local attack of the Cu-rich phase was observed, which formed an Fe/Ni/Co/Cr spinel that was surrounded by Cr2O3. This oxide was thicker for the humid air atmosphere when compared to dry air, and the transition of the Cu oxide to the spinel was accelerated. The Al-containing HEA formed a thin Al2O3 scale with humidity suppressing AlN formation and forming a smoother oxide layer. The Al+Cu composition had the highest overall oxidation resistance (minimal local attack, no nitridation) and also showed a smooth oxide scale topography under humid air oxidation as opposed to a plate-like, rougher scale under dry air.

Crystallography↗
NASA NTRS1990

Foam formation in low gravity

An apparatus that produced the first polyurethane foam in low gravity has been described. The chemicals were mixed together in an apparatus designed for operation in low gravity. Mixing was by means of stirring the chemicals with an electric motor and propeller in a mixing chamber. The apparatus was flown on Consort 1, the first low-gravity materials payload launched by a commercial rocket launch team. The sounding rocket flight produced over 7 min of low gravity during which a polyurethane spheroidal foam of approximately 2300 cu cm was formed. Photographs of the formation of the foam during the flight show the development of the spheroidal form. This begins as a small sphere and grows to approximately a 17-cm-diam spheroid. The apparatus will be flown again on subsequent low-gravity flights.

Wessling, Francis C.↗
DOE OSTI2021

In Situ Scattering Studies of Crystallization Kinetics in a Phase-Separated Zr–Cu–Fe–Al Bulk Metallic Glass

In this work, thermal stability and the crystallization kinetics of a phase-separated Zr-Cu-Fe-Al bulk metallic glass were investigated using in situ high-energy synchrotron X-ray and neutron diffraction, as well as small-angle synchrotron X-ray scattering. It was revealed that this glass with excellent glass-forming ability possesses a two-step crystallization behavior. The crystalline products and their evolution sequence are more complicated than a homogeneous Zr-Cu-Al glass with average glass-forming ability. The experimental results indicate that a finely distributed nanometer-sized cubic Zr 2 Cu phase forms first and then transforms to a tetragonal Zr 2 Cu phase, while the matrix transforms to an orthorhombic Zr3Fe phase. The strength of the Zr-Cu-Fe-Al composite containing cubic Zr 2 Cu phase and glass matrix increases, and the plasticity also improves compared to the as-cast Zr-Cu-Fe-Al bulk metallic glass. Our results suggest that the formation of multiple and complex crystalline products would be the characteristics of the Zr-Cu-Fe-Al glass with better glass-forming ability. Our study may shed light on the synthesis of bulk-sized glass-nanocrystals composites of high strength and good plasticity.

36 MATERIALS SCIENCE↗