Search NASA⌕ Search

SEARCH · Search NASA

Results for “Damage”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Grain Boundary Effects on Radiation Damage and Tritium Diffusion in Li–Al–O Ceramics from Molecular Dynamics and Experiments

Understanding irradiation damage and tritium transport in LiAlO2 ceramics is essential for their deployment in tritium-producing burnable absorber rods (TPBARs). Grain boundaries (GBs) play an important role in governing radiation response and tritium transport in LiAlO2 and its secondary phase LiAl5O8. Using molecular dynamics simulations, we investigated defect evolution and tritium diffusion during displacement cascades in single-crystal and bicrystal LiAlO2 and LiAl5O8 at 600 K. The results reveal that GBs suppress the damage in the LiAlO2 bicrystals as compared to single crystals, via interstitial emission. The effect is more pronounced for Li defects, than for Al and O. In LiAl5O8 the damage reduction due to introduction of GB is less pronounced overall. Tritium diffusion coefficients at GBs are higher by factors of 2–10 relative to diffusion inside grain bulk. The effect is particularly pronounced in LiAlO2, where S5, S17, and S25 GBs promote rapid tritium transport, whereas LiAl5O8 exhibits slower diffusion due to reduced free volume at its GBs. These findings evince a trade-off that while GBs mitigate radiation damage by absorbing interstitials, they simultaneously provide fast pathways for tritium migration which is not desirable for TPBAR application. The mechanistic insights gained here establish a foundation for microstructural design strategies to balance radiation tolerance and tritium retention in ceramic breeder materials.

Roy, Ankit↗
DOE OSTI2022

Effect of grain size on damage and failure in two-phase materials: Homogenized CuPb

It is well known that spall failure strongly depends on the microstructure of a material. There have been numerous studies to study the effect of grain size on the overall spall strength and the total amount of damage in single element metals like copper. However, such systematic studies remain rare in two-phase materials and alloys. In this work, two incipient spall experiments were performed on a Cu–1%Pb alloy to understand the effect of grain size on the damage and failure in a two-phase material. Overall, these results showed that even though the spall strength did not change as a function of grain size, there were significant differences in the total amount of damage as a function of grain size. A clear increase in the total damage present in the material was seen as the grain size was increased from 32 to either 70 or 75 μm in either of the experiments. Furthermore, this difference was attributed to variations in the void growth rate as the grain size was increased.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Turbulent flow characteristics in an 84-pin rod bundle for typical and damaged spacer grids

Hexagonal rod bundles arranged in a tightly packed triangular lattice are extensively used for heat transfer and energy generation applications. Staggered spacer grids are used to maintain the structural integrity of gas-cooled fast reactor (GFR) fuel assemblies, while inducing localized turbulence in flow. Damage to these spacer grids results in a disruption of flow fields within these hexagonal fuel bundles. Experimental flow visualizations are critical to identify the differences in local flow properties that the structural damage may cause. This experimental research investigates the flow-field characteristics at a near-wall and center plane in a prototypical 84-pin GFR fuel assembly. Newly installed typical spacers and spacers subject to naturally occurring damage due to material degradation over prolonged experimentation were investigated. Velocity fields were acquired by utilizing the matched-index-of-refraction method to obtain time-resolved particle image velocimetry measurements for a Reynolds number of 12 000. Reynolds decomposition statistical results divulged differences in the time-averaged velocity, velocity fluctuations, flow anisotropy, and Reynolds stress distributions. Galilean decomposition demarcated the influence of spacer grid damage on the velocity fields. To extract turbulent structures and elucidate mechanisms of flow instabilities, proper orthogonal decomposition analysis was employed. Reduced order flow reconstructions enabled the application of vortex identification algorithms to determine the spatial and statistical characteristics of vortices generated. This research work provides unique experimental data on the spacer grid condition-dependent flow. The results offer a deeper understanding of fluid dynamics behavior to support GFR rod bundle design efforts and computational fluid dynamics model validation.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effect of macroscopic surface defects on dynamic damage: An experimental and numerical study

This study examines the impact of macroscopic surface defects on the dynamic ductile damage behavior of polycrystalline metals using plate-impact experiments. Defects of various shapes (flat, round, and point) were manufactured on the free or impact surfaces of annealed copper specimens. The experiments were diagnosed with photon Doppler velocimetry measurements and soft recovery techniques. The experimental results revealed that defect shape and location significantly affect velocity–time profiles and void distribution. In order to understand the dynamics of shock propagation and corresponding ductile damage evolution within the target specimens, the impact experiments were modeled with a calibrated Tepla model, a dynamic ductile damage model for polycrystalline metals [Nguyen et al., Int. J. Solids Struct. 329, 113833 (2026)]. Overall, our resulting simulated velocity showed good agreement with measured velocity, and our simulated porosity distributions qualitatively matched experimental data. Based on our simulation results, defects on the free surface were found to distort rarefaction waves and therefore the corresponding spall planes. On the other hand, defects on the impact surface generated a delayed shock when the flyer plate and the defected target area were in contact, leading to distortion of the spall plane. The distortion of the spall plane resulted in a non-uniform distribution of voids within the defected specimens. Lastly, we examined the role of local work hardening due to the defect manufacturing process on the velocity and porosity distribution, using Tepla simulations with a simplified representation of local hardening. This investigation highlights the importance of defect geometry, location, and local hardening associated with defect generation in dynamic ductile damage processes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Integrated model predictions on the impact of substrate damage on gas dynamics during ITER burning-plasma operations

Divertor design and choice of plasma-facing materials (PFM) will be essential to the success of next-generation fusion reactors as they operate under more powerful scenarios. Understanding and controlling interactions between the plasma and PFM is essential to making these choices. Within these plasma–material interactions and especially in tungsten (W), the interplay between the most abundant plasma species (hydrogen isotopes and helium, He) with the wall material alters fuel retention. However, this interplay is yet to be sufficiently understood to confidently project fuel retention levels to future fusion devices. The paper presents a series of integrated simulations of fusion plasmas and their interaction with tungsten. Specifically, this study assesses the impact of He plasma pre-exposure on hydrogenic species retention during 100 s of burning plasma operations (BPO) in ITER. Multiple pre-exposure scenarios are considered, including sub-surface damage resulting from exposures in the linear device PISCES and from early ITER He-operation. The predictions from these consecutive He-BPO exposures show that fuel content and spatial distribution in the material are largely determined by the He-induced damage, as manifest in: (i) changes in surface temperature expected during BPO have little effect on fuel retention in the presence of He-induced damage; (ii) gas content stabilizes quickly in substrates pre-exposed in PISCES, at levels set by the concentration of pre-existing vacancies, while it continues to increase in substrates initially pristine or pre-exposed to ITER He plasmas; (iii) the presence of He and He–V clusters in the near-surface region locally increases hydrogenic retention, but decreases its permeation; this results in hydrogenic species that remain closer to the surface in pre-damaged substrates, while the bulk content is higher for initially pristine cases. In summary, the interaction and binding of D and T with the pre-existing He–V clusters modifies retention and permeation of hydrogen species during ITER BPO.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

ssDNA is an allosteric regulator of the C. crescentus SOS-independent DNA damage response transcription activator, DriD

DNA damage repair systems are critical for genomic integrity. However, they must be coordinated with DNA replication and cell division to ensure accurate genomic transmission. In most bacteria, this coordination is mediated by the SOS response through LexA, which triggers a halt in cell division until repair is completed. Recently, an SOS-independent damage response system was revealed in Caulobacter crescentus. This pathway is controlled by the transcription activator, DriD, but how DriD senses and signals DNA damage is unknown. To address this question, we performed biochemical, cellular, and structural studies. We show that DriD binds a specific promoter DNA site via its N-terminal HTH domain to activate transcription of genes, including the cell division inhibitor didA. A structure of the C-terminal portion of DriD revealed a WYL motif domain linked to a WCX dimerization domain. Strikingly, we found that DriD binds ssDNA between the WYL and WCX domains. Comparison of apo and ssDNA-bound DriD structures reveals that ssDNA binding orders and orients the DriD domains, indicating a mechanism for ssDNA-mediated operator DNA binding activation. Biochemical and in vivo studies support the structural model. Our data thus reveal the molecular mechanism underpinning an SOS-independent DNA damage repair pathway.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Employing sequential experiments to gain insights on the interaction between creep and fatigue damage in Ni‐base superalloys

Abstract The interaction between creep and fatigue damage in Ni‐base superalloy CMSX‐8 was explored using a sequential workflow that decouples creep and fatigue steps to quantify how accumulated creep damage interacts with subsequent isothermal low‐cycle fatigue (LCF) and vice versa. Two workflows were considered: creep followed by LCF and LCF followed by creep. For the first workflow, the subsequent LCF was evaluated at temperatures of 20°C, 750°C, and 1100°C. It was found that the extent of deleterious interaction of prior creep on LCF depended on increasing subsequent fatigue test temperature. For the LCF followed by creep, fatigue tests were first conducted at 20°C and 1100°C to 60% of life, and then creep was conducted at 800°C, where primary creep is promoted, or 900°C, where primary creep is absent. LCF damage accumulated at 1100°C accelerated creep and decreased ductility, while fatigue damage at room temperature had minimal effect on the creep behavior.

Gorgannejad, Sanam↗
DOE OSTI2022

Coupled diffusion-deformation-damage model for polymers used in hydrogen infrastructure

The soft materials used in the infrastructure of hydrogen storage and distribution systems are vulnerable because exposure to high-pressure hydrogen can lead to mechanical damage and property degradation. Some materials, such as polymers, can undergo mechanical failure due to a phenomenon wherein hydrogen gas diffuses through the polymer chains and occupies preexisting cavities or voids inside the polymer material. If the hydrogen gas pressure is reduced more quickly than hydrogen can diffuse back out of the polymer which is necessary for some applications, the trapped hydrogen gas instead escapes by rupturing the material, causing surface blistering or permanent damage. In this study, a continuum mechanics-based fully coupled diffusion-deformation model with damage is developed to predict the stress distribution and damage propagation while the polymer undergoes rapid decompression failure. The hyperelastic material model, along with the maximum principal strain failure theory, was chosen for this study as it represents the nonlinear material response with brittle failure observed in uniaxial tensile tests perfectly. EPDM polymer was chosen for this study because of its commercial availability and common use in hydrogen storage and distribution system. It has superior mechanical properties, high and low temperature resistance, and certain compounds work well in hydrogen gas. This work is useful for design engineers to alter the parameters while manufacturing polymer composites to increase their performance in a high-pressure hydrogen environment.

Kulkarni, Shank S.↗
DOE OSTI2022

Volumetric nondestructive evaluation for damage in carbon fiber reinforced polymer panels subjected to artificial lightning strikes

Aircrafts and wind turbine blades often get hit by lightning strikes due to their operating locations. With increasing incidents of lightning flashes every year due to global warming, damage assessment of CFRP structures after lightning strike to aircrafts and wind turbine blades is getting increasingly important. Many researchers are involved in designing better and more resilient lighting strike protection materials and often utilize non-destructuve evaluation (NDE) methods such as ultrasonic testing (UT), high-speed digital videograpgy, and high-speed IR thermography. In particular, UT is widely used due to its cost-effectiveness compared to other methods. Using UT imaging can obtain any potential damaged locations caused by lightning strike through the thickness of the composite specimens. Traditional UT and visual inspections only display the damage in units area, when in fact the UT data is volumetric. This study optimized the UT data to measure and display the volumetric damage after artificial lightning strike and is compared to the standardized visual inspection.

Spencer, Ryan↗
DOE OSTI2023

In situ measurement of damage evolution in shocked magnesium as a function of microstructure

Accurate modeling and prediction of damage induced by dynamic loading in materials have long proved to be a difficult task. Examination of postmortem recovered samples cannot capture the time-dependent evolution of void nucleation and growth, and attempts at analytical models are hindered by the necessity to make simplifying assumptions, because of the lack of high-resolution, in situ, time-resolved experimental data. We use absorption contrast imaging to directly image the time evolution of spall damage in metals at ~1.6-μm spatial resolution. We observe a dependence of void distribution and size on time and microstructure. The insights gained from these data can be used to validate and improve dynamic damage prediction models, which have the potential to lead to the design of superior damage-resistant materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Few-shot Learning for Post-disaster Structure Damage Assessment

Automating post-disaster damage assessment with remote sensing data is critical for faster surveys of structures impacted by natural disasters. One significant obstacle to training state-of-the-art deep neural networks to support this automation is that large quantities of labelled data are often required. However, obtaining those labels is particularly unrealistic to support post-disaster damage assessment in a timely manner. Few-shot learning methods could help to mitigate this by reducing the amount of labelled data required to successfully train a model while achieving satisfactory results. To this end, we explore a feature reweighting method to the YOLOv3 object detection architecture to achieve few-shot learning of damage assessment models on the xBD dataset. Our results show that the feature reweighting approach yield improved mAP over the baseline with significantly fewer labelled samples. In addition, we use t-SNE to analyze the class-specific reweighting vectors generated by the reweighting module in order to evaluate their inter-class and intra-class similarity. We find that the vectors form clusters based on class, and that these clusters overlap with visually similar classes. Those results show the potential to employ this few-shot learning strategy for rapid damage assessment with post-event remote sensing images.

Bowman, Jordan↗
DOE OSTI2022

Storm DEPART(Damage Estimate Prediction And Recovery Tool)

Damage prediction, materials needed, and resource allocation modeling capability in order to support pre-incident planning and preparation by predicting damage to the power generation capacity, transmission grids, distribution networks, and communications assets. The capabilities will be developed by multiple factors to include wind bands, storm surge, and flooding forecasts to participant’s assets which will result in a report of predicted damages. Additional factors to include available participants infrastructure data to include class, age, construction, location, wind rating, and additional information not in the public domain. Based on predicted damages, the output will be a bill of materials (BOM) to support short-term recovery operations. The extensiveness and level of detail for this BOM will depend on the replacement configuration specifications provided for each individual participant asset. Any limiting factors for the model will be applied related supply chain and resource constraints.

Klett, Mary↗
DOE OSTI2021

The effects of well damage and completion designs on geoelectrical responses in mature wellbore environments

Well integrity is one of the major concerns in long-term geologic storage sites due to the potential risk of well leakage and groundwater contamination. Evaluating changes in electrical responses due to energized steel-cased wells has the potential to quantify and predict possible wellbore failures because any kind of breakage or corrosion along highly conductive well casings will have an impact on the distribution of the subsurface electrical potential. However, realistic wellbore-geoelectrical models that can fully capture fine-scale details of well completion design and the state of well damage at the field scale require extensive computational effort, or they can even be intractable to simulate. To overcome this computational burden while still keeping the model realistic, we have used the hierarchical finite-element method that represents electrical conductivity at each dimensional component (1D edges, 2D planes, and 3D cells) of a tetrahedral mesh. This allows well completion designs with real-life geometric scales and well systems with realistic, detailed, progressive corrosion and damage in our models. We have developed a comparison of possible discretization approaches of a multicasing completion design in the finite-element model. The effects of the surface casing and the coupling between concentric well casings as well as the effects of the degree and the location of well damage on the electrical responses are also examined. As a result, we analyze real surface electric field data to detect wellbore integrity failure associated with damage.

58 GEOSCIENCES↗
DOE OSTI2026

Nanosecond dual-wavelength irradiation effects on laser-induced damage in hafnia coatings

Nanosecond dual-wavelength laser-induced damage was investigated at 1064 nm (1ω) and 355 nm (3ω) on ion-beam-sputtered hafnia single-layer coatings. Single-wavelength 1-on-1 tests were first conducted to establish reference onset fluences. Dual-wavelength tests combined a primary beam with variable fluence at one wavelength and a background, secondary wavelength beam with fixed fluences set to several percentages of the corresponding onset fluence. When 1ω was used as the background irradiation, the perceived damage resistance at 3ω decreased gradually. Here, in contrast, 3ω background irradiation at as little as 10% of the onset fluence led to an ≈ 50% abrupt reduction in the perceived 1ω damage resistance, followed by modest changes upon further increases in 3ω background fluences. Scanning electron microscopy and conversion ratios indicate that 3ω light is the primary driver of damage onset in the case of dual wavelength irradiation. A two-step precursor generation and activation model reproduces the 3ω behavior (1ω as background), but not the strong initial 1ω reduction (3ω as background), suggesting additional 3ω-induced precursors that saturate at low fluence.

Optics and optical instruments↗
DOE OSTI2025

Investigation of the distribution of laser-induced damage precursors in etched grating sidewalls fabricated using inductively coupled plasma reactive-ion etching

Inductively coupled plasma reactive-ion etching for grating fabrication is explored with emphasis on the type and distribution of process-induced defects that can act as precursors to laser-induced damage initiation. To provide flexibility in the ability to perform a variety of material characterization methods, grating-like features with large pitch were fabricated in silica monolayers. The results indicate that the etch process introduces surface fluorine and subsurface carbon-containing contamination, which reduces the laser-induced damage threshold. The local relative concentrations of the laser-damage precursors introduced during the etch step of the manufacturing process were investigated using angle-resolved damage testing, taking advantage of the shift of the location of the peak electric-field intensity incident on the grating sidewall. The results suggest an increased level of etch-related defects near the base of the sidewall, with directly fluorinated silicon identified as the primary defect.

Dent, R. [Univ. of Rochester, NY (United States). ↗
DOE OSTI2020

Performance Analysis and Radiation Damage Estimation of the Stopping Target Monitor Detectors in Mu2e

The Mu2e experiment aims to search for the charged lepton flavour violating (CLFV) process of a coherent, neutrinoless, conversion of a muon into an electron within the proximity of an aluminium nucleus. Mu2e seeks to measure the ratio (R μe ) of the rate of this conversion process, relative to that of ordinary muon capture. Mu2e will achieve world-leading sensitivity, improving the current limit of Rμe < 7 ×10 -13 (90% C.L.),set by the SINDRUM-II experiment, by an order of 104. This corresponds to a single-event sensitivity of Rμe < 2.87 × 10 -17 (90% C.L.). Many beyond Standard Model (BSM) theories require CLFV to occur at a rate accessible by Mu2e. Any observation of CLFV at Mu2e would have profound implications on particle physics. The Stopping Target Monitor (STM) will be comprised of both a HPGe and a LaBr3 detector which will monitor the signals of photons produced in stopped-muon processes to a required accuracy of 10%. To achieve the desired sensitivity, it is imperative that the detectors perform at their optimal level. The STM detectors are placed within a harsh radiation environment in the form of a high energy ‘flash’ of gamma radiation as well as a flux of fast neutrons. Estimations of radiation damage to HPGe in literature is limited. This thesis reports an approach which utilizes the Kinetic-Energy Released in Matter (KERMA) parameter that considers the energy dependence of the incident flux and the cross-section information for the incident particle. Resampling schemes have been adopted to give a realistic rate over the experiment run time. The results have then been normalized to the radiation damage caused by a 252 Cf source. The estimated time before annealing of the detector is necessary is found to be 75 and 78 months in the case of neutron damage and τ ~ 24 years, 11 months in the case of electron/positron induced damage. This shows significant improvement on the previous estimations.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solar Photovoltaic (PV) Damage Assessment After Typhoon Mawar: Findings and Recommendations for Resilient PV on Guam

A team from the National Renewable Energy Laboratory (NREL) visited Guam in August 2023 to assess failure modes of solar photovoltaic (PV) systems after Typhoon Mawar and to provide recommendations to increase the resilience of PV systems on Guam. The team visited 30 systems: commercial and utility scale, and rooftop and ground-mounted. The team observed systems with no apparent damage, as well as systems that were completely lost. Systems fared very well overall. The average failure rate of rooftop systems was 18%, with a median failure rate of 2%, meaning the few systems that suffered total loss pulled up the average. Only eight 8 of the 25 rooftop systems suffered more than 5% damage. All ground-mounted systems suffered less than 0.5% damage, aside from a carport that lost 16% of its modules. PV systems at Andersen Air Force Base suffered 5% damage on average, with a median system failure of 0.6%. In almost all cases, failures were the result of: (1) Inadequate clamping of the module frame to the mount, (2) Module mounting clamps rotating out of underlying support rail (i.e., T-bolt that rotates free at less than 60 degrees of rotation), (3) An object hitting the panel resulting in a fracture, and in some cases leading to a cascading failure of several more panels, and (4) Excessive tilt angle (in Guam, greater than 5 degrees can be a risk due to wind speed, and power production trade-offs are insignificant).

14 SOLAR ENERGY↗
DOE OSTI2024

A Multiphysics Multiscale Simulation Platform for Damage, Environmental Degradation, and Life Prediction of CMCs in Extreme Environments

This project successfully developed a multiphysics, multiscale computational framework to enhance the design and development of CMCs, with a focus on modeling highly nonlinear, time-dependent damage mechanisms and material degradation under extreme conditions, such as those experienced in turbine service environments. The project made significant advances in improving our understanding of progressive damage, oxidative degradation, and time-dependent inelastic deformation in CMCs, with particular attention to the role of uncertainties in predictions. Key outcomes include the integration of advanced material characterization, uncertainty quantification, and multiphysics constitutive models to predict the behavior of CMCs over their service life. A novel multiscale methodology was employed, which integrated microscale constituent behaviors with structural-scale responses, enabling the manufacturing defects in the microstructure that are prone to damage nucleation. Through the development of DL algorithms, the project advanced the prediction of damage initiation and crack propagation, taking into account the defect morphology and statistical variations across multiple scales. The framework was rigorously validated using thermomechanical experiments, which tested CMCs under various mechanical loadings at elevated temperatures, further enhancing the model's predictive capability. Overall, the research outcomes have provided a more accurate, reliable method for predicting CMC component life, significantly advancing material design, and improving component reliability in extreme environments. This work has strong implications for the optimization of turbine components and other high-performance applications where CMCs are used.

03 NATURAL GAS↗