Search NASA⌕ Search

SEARCH · Search NASA

Results for “Design Load”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Variable Stiffness Spar Wind-Tunnel Model Development and Testing

The concept of exploiting wing flexibility to improve aerodynamic performance was investigated in the wind tunnel by employing multiple control surfaces and by varying wing structural stiffness via a Variable Stiffness Spar (VSS) mechanism. High design loads compromised the VSS effectiveness because the aerodynamic wind-tunnel model was much stiffer than desired in order to meet the strength requirements. Results from tests of the model include stiffness and modal data, model deformation data, aerodynamic loads, static control surface derivatives, and fuselage standoff pressure data. Effects of the VSS on the stiffness and modal characteristics, lift curve slope, and control surface effectiveness are discussed. The VSS had the most effect on the rolling moment generated by the leading-edge outboard flap at subsonic speeds. The effects of the VSS for the other control surfaces and speed regimes were less. The difficulties encountered and the ability of the VSS to alter the aeroelastic characteristics of the wing emphasize the need for the development of improved design and construction methods for static aeroelastic models. The data collected and presented is valuable in terms of understanding static aeroelastic wind-tunnel model development.

Florance, James R.↗
NASA NTRSDate not supplied

Thin-Ply: Exploration and Manufacturing with Automated Fiber Placement

Abstract Highly repeatable and nearly defect-free fabrication of composite parts is critical to the success and widespread acceptance of composite materials. Through optimization using thin-ply materials, composite parts can be manufactured to be lighter and tailored more specifically to anticipated design loads than with standard prepreg materials alone. However, defects arising from the thin-ply manufacturing process are not always similar to defects found with standard tows. These new defects warrant evaluation. At NASA Langley Research Center, the manufacturing process parameters associated with automated fiber placement (AFP), a slit tape-based composite manufacturing process, were optimized for the use of a thin-ply prepreg carbon-epoxy material. Carbon-epoxy tows with areal weights of 30 g/m2 and 70 g/m2 were used in these manufacturing trials. The AFP process parameters of heater output, compaction force, tow feed rate, and tow tension were adjusted and optimized for successful manufacturing. This article documents an exploration of thin-ply fabrication on both flat and complex-shaped surfaces. Ultimately, aerospace-quality laminates were made from the 70-g/m2 material, but imperfections in the 30-g/m2 material itself and the fact that the AFP machine was not designed for such a thin material meant that more research and trials are required to obtain flight-quality 30-g/m2 laminates.

Carbon-expoxy↗
NASA NTRSDate not supplied

Exploration and Manufacturing with Automated Fiber Placement

Highly repeatable and nearly defect-free fabrication of composite parts is critical to the success and widespread acceptance of composite materials. Through optimization using thin-ply materials, composite parts can be manufactured to be lighter and tailored more specifically to anticipated design loads than with standard prepreg materials alone. However, defects arising from the thin-ply manufacturing process are not always similar to defects found with standard tows. These new defects warrant evaluation. At NASA Langley Research Center, the manufacturing process parameters associated with automated fiber placement (AFP), a slit tape-based composite manufacturing process, were optimized for the use of a thin-ply prepreg carbon-epoxy material. Carbon-epoxy tows with areal weights of 30 g/m2 and 70 g/m2 were used in these manufacturing trials. The AFP process parameters of heater output, compaction force, tow feed rate, and tow tension were adjusted and optimized for successful manufacturing. This article documents an exploration of thin-ply fabrication on both flat and complex-shaped surfaces. Ultimately, aerospace-quality laminates were made from the 70-g/m2 material, but imperfections in the 30-g/m2 material itself and the fact that the AFP machine was not designed for such a thin material meant that more research and trials are required to obtain flight-quality 30-g/m2 laminates.

carbon-epoxy↗
NASA NTRS1998

Room Temperature and Elevated Temperature Composite Sandwich Joint Testing

Testing of composite sandwich joint elements has been completed to verify the strength capacity of joints designed to carry specified running loads representative of a high speed civil transport wing. Static tension testing at both room and an elevated temperature of 350 F and fatigue testing at room temperature were conducted to determine strength capacity, fatigue life, and failure modes. Static tension test results yielded failure loads above the design loads for the room temperature tests, confirming the ability of the joint concepts tested to carry their design loads. However, strength reductions as large as 30% were observed at the elevated test temperature, where all failure loads were below the room temperature design loads for the specific joint designs tested. Fatigue testing resulted in lower than predicted fatigue lives.

Walker, Sandra P.↗
NASA NTRS1988

Sensitivity analysis of a deployable three longeron truss beam designed for minimum member loads during deployment

The significant design variables of a deployable three longeron truss beam, designed for minimum member loads during deployment, are identified and the sensitivity of the load level in the members of the truss beam due to variations of the design variables is established. The analysis of the deployment models, developed in this paper, is carried out using a commercially available computer code, called DADS. Based on the results of the analysis, guidelines are formulated for the design of a deployable three longeron truss beam to achieve minimum loads in the members during deployment. The paper concludes with a brief discussion of the applicability of the approach, taken in this paper, to other truss configurations.

Warnaar, Dirk B.↗
DOE OSTI2020

IEA Wind Task 32 and Task 37: Optimizing Wind Turbines with Lidar-Assisted Control Using Systems Engineering

Lidar-assisted control is a promising technology for reducing the levelized cost of energy from wind turbines, but quantifying its impact at the overall system level requires sophisticated systems engineering analysis and optimization frameworks. The joint workshop on Optimizing Wind Turbines with Lidar-Assisted Control Using Systems Engineering was held by the International Energy Agency Wind Task 32 (Lidar) and Task 37 (Systems Engineering) in October 2019 to address this challenge. This paper summarizes the outcome of the workshop and presents a road map for further research. The most promising applications of lidar-assisted control identified at the workshop and discussed here include 1) increasing annual energy production, 2) decreasing capital expenditure costs by reducing design loads, 3) extending turbine lifetime by reducing operating loads, and 4) enabling wind turbine class upgrades. For each application, we review the state of the art and highlight remaining research needs. Finally, we discuss strategies for addressing these research needs by conducting high-fidelity systems engineering optimizations.

17 WIND ENERGY↗
DOE OSTI2022

Experimental Determination of Constitutive Response of Alloy 800H in Support of Viscoplastic Constitutive Model Development for ASME Section III, Division 5, Class A Applications

In FY 2022, a development effort was initiated at the US Department of Energy’s Argonne National Laboratory (Argonne) and Oak Ridge National Laboratory (ORNL) to develop the Alloy 800H viscoplastic constitutive model so that inelastic analysis methods can support high-temperature gas-cooled reactor (HTGR) designs. The viscoplastic constitutive equations will be developed at Argonne. The ORNL effort focuses on generating test data from various high-temperature experiments with specially designed loading histories to probe Alloy 800H’s constitutive response.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Design of a shipping fixture for a compact cryomodule hermetic assembly

Two conduction-cooled 915 MHz superconducting radio frequency hermetic assemblies must be safely transported from the Jefferson Lab in Newport News, VA to General Atomics in San Diego, CA for perfor-mance testing in a custom horizontal test cryostat. One hermetic assembly consists of a 2-cell 915 MHz cavity, a coaxial fundamental power coupler, and the warm-to-cold transition beam tubes. The second hermetic assembly consists of a 2-cell 915 MHz cavity only. The assemblies will be transported on a flatbed air-ride trailer over the approximate 4000 km distance. Design requirements included adequate attenuation of 4g vertical axis, 5g beamline axis, and 1.5g lateral axis shock events. The isolation system was designed using helical wire-rope isolators with modal and transient finite element analysis performed in Ansys. Results show shock attenuation of a 10 ms half-sine pulse input to < 1g in the vertical axis, < 1.5g in the beam-line axis, and < 0.5g in the lateral axis for both assem-blies at the specified design loads and all structural stresses are kept below the material yield limits. Addi-tionally, the natural frequencies of both isolation sys-tems adequately attenuate the fundamental modes of the critical structures.

Accelerator Physics↗
DOE OSTI2023

Sensitivity Analysis of Modal Parameters of a Jacket Offshore Wind Turbine to Operational Conditions

Accurate estimation of offshore wind turbine (OWT) modal parameters has a prominent effect on the design loads, lifetime prediction, and dynamic response of the system. Modal parameters can vary during the operation of OWTs. This paper studies the variation and sensitivity analysis of an OWT’s modal parameters with respect to operational and environmental conditions. Three finite element models of a jacket-supported OWT at the Block Island Wind Farm are created within the OpenSees, SAP2000, and OpenFAST platforms and validated using experimental measurements. The OpenFAST model is used to simulate the modal parameters of the turbine under various wind speed, rotor speed, power, yaw angle, mean sea level, blade pitch angle, and soil spring values. The model-predicted modal parameters of the first fore–aft (FA) and side–side (SS) modes are compared to those identified from experimental measurements. Results from the simulations show that the first FA natural frequency and damping ratio mostly depend on the rotor speed and wind speed, respectively, while yaw angle and mean sea level do not have a visible effect. It is observed that there is about 8% stiffening in the first FA frequency and an aerodynamic damping of 7.5% during the operation of the OWT.

17 WIND ENERGY↗
NASA NTRS1972

Investigation of Structural Factors of Safety for the Space Shuttle

A study was made of the factors governing the structural design of the fully reusable space shuttle booster to establish a rational approach to select optimum structural factors of safety. The study included trade studies of structural factors of safety versus booster service life, weight, cost, and reliability. Similar trade studies can be made on other vehicles using the procedures developed. The major structural components of a selected baseline booster were studied in depth, each being examined to determine the fatigue life, safe-life, and fail-safe capabilities of the baseline design. Each component was further examined to determine its reliability and safety requirements, and the change of structural weight with factors of safety. The apparent factors of safety resulting from fatigue, safe-life, proof test, and fail-safe requirements were identified. The feasibility of reduced factors of safety for design loads such as engine thrust, which are well defined, was examined.

Source record↗
NASA NTRS1974

Viking Mars lander 1975 dynamic test model/orbiter developmental test model forced vibration test

The Viking Mars Lander 1975 dynamic test model and orbiter developmental test model were subjected to forced vibration sine tests. Flight acceptance (FA) and type approval (TA) test levels were applied to the spacecraft structure in a longitudinal test configuration using a 133,440-N (30,000-lb) force shaker. Testing in the two lateral axes (X, Y) was performed at lower levels using four 667-N (150-lb) force shakers. Forced vibration qualification (TA) test levels were successfully imposed on the spacecraft at frequencies down to 10 Hz. Measured responses showed the same character as analytical predictions, and correlation was reasonably good. Because of control system test tolerances, orbiter primary structure generally did not reach the design load limits attained in earlier static testing. A post-test examination of critical orbiter structure disclosed no apparent damage to the structure as a result of the test environment.

Fortenberry, J.↗
NASA NTRS1974

Effects of porosity on weld-joint tensile strength of aluminum alloys

Tensile properties in defect-free weldments of aluminum alloys 2014-T6 and 2219-T87 (sheet and plate) are shown to be related to the level or concentration of induced simulated porosity. The scatter diagram shows that the ultimate tensile strength of the weldments displays the most pronounced linear relationship with the level of porosity. The relationships between yield strength or elongation and porosity are either trivial or inconsequential in the lower and intermediate levels of porosity content. In highly concentrated levels of porosity, both yield strength and elongation values decrease markedly. Correlation coefficients were obtained by simple straight line regression analysis between the variables of ultimate tensile strength and pore level. The coefficients were greater, indicating a better correlation, using a pore area accumulation concept or pore volume accumulation than the accumulation of the pore diameters. These relationships provide a useful tool for assessing the existing aerospace radiographic acceptance standards with respect to permissible porosity. In addition, these relationships, in combination with known design load requirements, will serve as an engineering guideline in determining when a weld repair is necessary based on accumulative pore level as detected by radiographic techniques.

Lovoy, C. V.↗
NASA NTRS1975

Aerocrane: A hybrid LTA aircraft for aerial crane applications

The Aerocrane, a hybrid aircraft, combines rotor lift with buoyant lift to offer VTOL load capability greatly in excess of helicopter technology while eliminating the airship problem of ballast transfer. In addition, the Aerocrane concept sharply reduces the mooring problem of airships and provides 360 deg vectorable thrust to supply a relatively large force component for control of gust loads. Designed for use in short range, ultra heavy lift missions, the Aerocrane operates in a performance envelope unsuitable for either helicopters or airships. Basic design considerations and potential problem areas of the concept are addressed.

Perkins, R. G., Jr.↗
NASA NTRS1976

Vortex maneuver lift for super-cruise configurations

Some of the theoretical and experimental research conducted at the NASA Langley Research Center is presented to investigate the subsonic vortex-lift producing capabilities for two classes of Super-Cruise designs: a close-coupled wing-canard arrangement and a slender wing configuration. In addition, several analytical methods are discussed for estimating critical structural design loads for thin, highly swept wings having separated leading-edge vortex flows.

Campbell, J. F.↗
NASA NTRS1976

D-1A equipment module structure test

The Centaur Equipment Module (E/M) structural test program was performed in two parts due to an unscheduled hardware failure in the first test series. The objectives of the initial test program were to define the flexibility characteristics of the E/M, verify the design load capability, and determine its ultimate strength capability by loading to structural failure. However, during the first failure test attempt, the Intelsat IV MPA failed instead of the E/M. Therefore a new adapter was fabricated to simulate the HEAO mission adapter and the second series of tests were then performed. They concluded with the failure of the E/M forward interface ring resulting in about 3.5 degrees of permanent set on the high compression side. Nevertheless, the linear or useable strength capability of the E/M is greater or equal to that which is required for the HEAO missions. The E/M is deemed structurally qualified for the HEAO missions.

Niezgoda, T. F.↗
NASA NTRS1976

Results of the Low Speed Aeroelastic Buffet Test with a 0.046-scale Model (747-ax1322-d-3/orbiter 8-0) of the 747 Cam/orbiter in the University of Washington Wind Tunnel (CS 3)

A series of wind tunnel studies designed to assess the potential buffet problems resulting from orbiter wake characteristics with its tailcone removed are presented to provide design loads and acceleration environments, and to develop data on buffet sensitivity to various aerodynamic configurations and flight parameters. Data are intended to support subsequent analyses of structural fatigue life, crew efficiency, and equipment vibrations.

Gillins, R. L.↗
NASA NTRS1976

Results of boron-aluminum thrust structure

Results are presented of testing-to-failure a two member boron-aluminum thrust structure. The structure represented one section of a more complex planar truss and was designed to test the integrity of a diffusion bonded joint. The structure failed at 107 percent of the ultimate design load in the diffusion bond region. Strain gages and displacement transducers were used to measure loads and deflections of the truss. The experimentally derived axial loads, bending moments, and torsion in the various members are presented and compared with predicted values.

Hyer, M. W.↗