Search NASA⌕ Search

SEARCH · Search NASA

Results for “Differential Geometry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Investigation of tidal displacements of the earth's surface by laser ranging to GEOS-3

Two different approaches to the problem were investigated: (1) a dynamic method that computed pass-to-pass apparent movements in station height relative to short arcs fitted to several passes of data from the same station, and (2) a quasi-geometric method that reduces the dependence on unmodelled satellite dynamics to a knowledge of only the radial position of the satellite by considering two-station simultaneous ranging at the precise time that the satellite passes through the plane defined by the two stations and the center of the mass of the earth. The dynamic method was applied to 24-hour arcs in an attempt to study the total tidal displacement at Goddard, but it was found to be unsuitable. The quasi-geometry method, on the other hand, is significantly less influenced by these effects because it is sensitive principally to the differential tidal displacements between laser stations. Using this method, a good approximation to the theoretical Love number h sub 2 was obtained from five passes over the GEOS-3 calibration area when a systematic bias of 2.16 meters was allowed in the radial distance to the satellite.

Bower, D. R.↗
NASA NTRS1993

Silicon Holder For Molecular-Beam Epitaxy

Simple assembly of silicon wafers holds silicon-based charge-coupled device (CCD) during postprocessing in which silicon deposited by molecular-beam epitaxy. Attains temperatures similar to CCD, so hotspots suppressed. Coefficients of thermal expansion of holder and CCD equal, so thermal stresses caused by differential thermal expansion and contraction do not develop. Holder readily fabricated, by standard silicon processing techniques, to accommodate various CCD geometries. Silicon does not contaminate CCD or molecular-beam-epitaxy vacuum chamber.

Hoenk, Michael E.↗
NASA NTRS1993

Nonlinear dynamic simulation of single- and multi-spool core engines

In this paper a new computational method for accurate simulation of the nonlinear dynamic behavior of single- and multi-spool core engines, turbofan engines, and power generation gas turbine engines is presented. In order to perform the simulation, a modularly structured computer code has been developed which includes individual mathematical modules representing various engine components. The generic structure of the code enables the dynamic simulation of arbitrary engine configurations ranging from single-spool thrust generation to multi-spool thrust/power generation engines under adverse dynamic operating conditions. For precise simulation of turbine and compressor components, row-by-row calculation procedures were implemented that account for the specific turbine and compressor cascade and blade geometry and characteristics. The dynamic behavior of the subject engine is calculated by solving a number of systems of partial differential equations, which describe the unsteady behavior of the individual components. In order to ensure the capability, accuracy, robustness, and reliability of the code, comprehensive critical performance assessment and validation tests were performed. As representatives, three different transient cases with single- and multi-spool thrust and power generation engines were simulated. The transient cases range from operating with a prescribed fuel schedule, to extreme load changes, to generator and turbine shut down.

Schobeiri, T.↗
NASA NTRS1993

The warped disk of Centaurus A in the near-infrared

We present infrared images of Cen A (NGC 5128) in the J, H, and K bands. The infrared morphology is primarily determined by the presence of a thin absorptive warped disk. By integrating the light of the underlying prolate galaxy through such a disk, we construct models which we compare with infrared and X-ray data. The geometry of the warped disk needed to fit the IR data is consistent with a warped disk which has evolved as a result of differential precession in a prolate potential. The disk has an inclination, with respect to the principal axis of the underlying elliptical galaxy, that is higher at larger radii than in the inner region. A scenario is proposed where a small gas-rich galaxy infalling under the force of dynamical friction is tidally stripped. Stripping occurs at different times during its infall. The orientation of the resulting gas disk depends upon the angular momentum of the infalling galaxy. We find that the resulting precession angle of the disk is well described by the precession model, but that the inclination angle may vary as a function of radius. We propose an orbit for the infalling galaxy that is consistent with the geometry of the warped disk needed to fit our infrared data, and rotation observed in the outer part of the galaxy.

Quillen, A. C.↗
NASA NTRS2020

Communication-Aware Orbit Design for Small Spacecraft Swarms around Small Bodies

Exploration of small Solar System bodies has traditionally been performed by single monolithic spacecraft carrying a number of science instruments. However, science instruments typically cannot be operated simultaneously due to the instrument requirements including optimal viewing angle, surface illumination, altitude and ground resolution, power, and data constraints. This observation has motivated interest in multi-spacecraft architectures where a swarm of small spacecraft, each carrying a single science instrument, studies a small body after being deployed by a carrier spacecraft, which then collects data from the vehicles and relays it to Earth. Such architectures hold promise to yield significant improvements in mission efficiency, increases in data quality, and shorter mission duration. A key difficulty in the design of such missions is the selection of orbits for the small spacecraft, which must satisfy not only instrument requirements, but also strict inter-spacecraft communication and on-board storage constraints. To address this, in this paper, we present a novel computationally-efficient optimization algorithm for \emph{communication-aware design} of the orbits of a small spacecraft swarm orbiting a small body. The proposed approach captures constraints including instrument requirements, inter-spacecraft communication bandwidths, and on-board memory usage, and it can accommodate highly irregular gravity field models and surface geometries. We propose an efficient algorithm for optimization of instrument observations and inter-spacecraft communications; we then leverage the differentiable nature of the proposed algorithm to accelerate a gradient-based global search algorithm. Numerical simulations of a six-spacecraft swarm studying 433 Eros show that the proposed approach successfully identifies high-quality orbits, and significantly outperform communication-agnostic optimization techniques, resulting in a 10% increase in scientific returns and a 30% increase in the quality of the collected data.

Rahmani, Amir↗
NASA NTRS1973

Comparison of finite-difference schemes for analysis of shells of revolution

Several finite difference schemes are applied to the stress and free vibration analysis of homogeneous isotropic and layered orthotropic shells of revolution. The study is based on a form of the Sanders-Budiansky first-approximation linear shell theory modified such that the effects of shear deformation and rotary inertia are included. A Fourier approach is used in which all the shell stress resultants and displacements are expanded in a Fourier series in the circumferential direction, and the governing equations reduce to ordinary differential equations in the meridional direction. While primary attention is given to finite difference schemes used in conjunction with first order differential equation formulation, comparison is made with finite difference schemes used with other formulations. These finite difference discretization models are compared with respect to simplicity of application, convergence characteristics, and computational efficiency. Numerical studies are presented for the effects of variations in shell geometry and lamination parameters on the accuracy and convergence of the solutions obtained by the different finite difference schemes. On the basis of the present study it is shown that the mixed finite difference scheme based on the first order differential equation formulation and two interlacing grids for the different fundamental unknowns combines a number of advantages over other finite difference schemes previously reported in the literature.

Noor, A. K.↗
DOE OSTI2025

Enhanced Ion Transport and Molecular Packing Stability in Asymmetric 2D Nanostructured π‐Conjugated Thieno[3,2‐b]Thiophene‐Based Liquid Crystal

Organic semiconductors based on liquid crystal (LC) molecules have attracted increasing interest. Here, in this work, two linear LCs based on 2,5‐bis(thien‐2‐yl)thieno[3,2‐b]thiophene (BTTT) mesogen are designed and synthesized, including BTTT/dEO3 with two symmetrically attached tri(ethylene oxide) groups and BTTT/mEO6 with one asymmetrically attached hexa(ethylene oxide) group. These two molecules have comparable functional‐group compositions but different molecular geometries, leading to their moderately different material performances. Both LCs show smectic mesophases with relatively low transition temperatures as confirmed by differential scanning calorimetry and polarized optical microscopy. A combination of experimental grazing incidence wide‐angle X‐ray scattering and molecular dynamics (MD) simulations reveals a herringbone packing motif of BTTT segments in both LCs while a smaller molecular tilt angle in BTTT/mEO6. Ionic conductivities are measured by doping LCs with different amounts of ionic dopants, lithium bis(trifluoromethanesulfonyl)imide (LiTFSI). BTTT/mEO6 shows better smectic phase stability to higher LiTFSI doping ratios. Both LCs exhibit similar ionic conductivities in the smectic phases, but BTTT/mEO6 outperforms BTTT/dEO3 by a factor of three in the amorphous phase at higher temperatures. MD simulations, performed to examine the ion solvation environment, reveal that BTTT/mEO6 is more efficient in coordinating Li‐ions and screening their interactions with TFSI‐ions which further promote ionic transport.

grazing incidence wide-angle X-ray scattering↗
NASA NTRS1972

New circumferential seal design concept using self-acting lift geometries

Seal operating temperatures, leakage (pressurizing gas flow), torque, and wear of a conventional circumferential shaft seal were measured and compared to those of a conventional seal modified to have self-acting lift geometries. Both seal types had a 2.625-in diameter bore and were operated at a sliding velocity of 150 ft/sec with differential pressures ranging from 0 to 100 psi. Results of this investigation show that the self-acting seal operated at lower bulk carbon temperatures with half the torque and approximately one-tenth the wear of the conventional seal. Seal leakage of the self-acting seal was of order of 0.04 scfm for pressures above 60 psi which is well within the accepted range for gas turbine engine applications.

Hady, W. F.↗
NASA NTRS1975

Numerical techniques for the solution of the compressible Navier-Stokes equations and implementation of turbulence models

The time-splitting explicit numerical method of MacCormack is applied to separated turbulent boundary layer flow problems. Modifications of this basic method are developed to counter difficulties associated with complicated geometry and severe numerical resolution requirements of turbulence model equations. The accuracy of solutions is investigated by comparison with exact solutions for several simple cases. Procedures are developed for modifying the basic method to improve the accuracy. Numerical solutions of high-Reynolds-number separated flows over an airfoil and shock-separated flows over a flat plate are obtained. A simple mixing length model of turbulence is used for the transonic flow past an airfoil. A nonorthogonal mesh of arbitrary configuration facilitates the description of the flow field. For the simpler geometry associated with the flat plate, a rectangular mesh is used, and solutions are obtained based on a two-equation differential model of turbulence.

Baldwin, B. S.↗
NASA NTRS1985

A Preliminary Assessment of LANDSAT-4 Thematic Mapper Data

The geometric errors for image to map rectification of one Thematic Mapper (TM) scene of an area near Windsor, Ontario were studied. The scene had been produced on computer compatible tape by NASA and contained radiometric and system corrections for geometric distortions. The geometric properties of TM photographic imagery permitted very good fitting to map detail using simple scaling techniques to localized areas and, using simple scaling, the overall geometry remained with 500 meters or 0.4 mm at the image scale of 1:1,141,600. An affine transformation, permitting differential scaling, slightly improves the fit to about 400 meters or 0.35 mm at image scale. The imagery shows promise of having the needed additional resolution and spectral discrimination to provide map revision information in urban-rural areas where the MSS sensor is considered inadequate. The late-season prairie image, however, did not hold such promise, and judgement must be reserved until images are acquired at other seasons in this particular geographic area.

Goodenough, D. G.↗
NASA NTRS1986

Analysis of the harmonic gyrotron traveling wave amplifier

A single nonlinear differential equation is derived for describing the spatial evolution of the wave field in a gyrotron amplifier on the cylindrical guide geometry. The equation is then used to determine the efficiencies and the optimized interaction lengths for gyrotron operated with TE sub N1 modes at the N-th cyclotron harmonic. The equation offers a significant advantage in simplifying numerical work in comparison with the brute force particle simulation approach. The efficiencies of the harmonic operations by using a hollow beam decrease quickly with increasing harmonic number, but are enhanced by using an axis-encircling beam instead.

Kuo, S. P.↗
NASA NTRS2002

Computing Aerodynamic Performance of a 2D Iced Airfoil: Blocking Topology and Grid Generation

The ice accrued on airfoils can have enormously complicated shapes with multiple protruded horns and feathers. In this paper, several blocking topologies are proposed and evaluated on their ability to produce high-quality structured multi-block grid systems. A transition layer grid is introduced to ensure that jaggedness on the ice-surface geometry do not to propagate into the domain. This is important for grid-generation methods based on hyperbolic PDEs (Partial Differential Equations) and algebraic transfinite interpolation. A 'thick' wrap-around grid is introduced to ensure that grid lines clustered next to solid walls do not propagate as streaks of tightly packed grid lines into the interior of the domain along block boundaries. For ice shapes that are not too complicated, a method is presented for generating high-quality single-block grids. To demonstrate the usefulness of the methods developed, grids and CFD solutions were generated for two iced airfoils: the NLF0414 airfoil with and without the 623-ice shape and the B575/767 airfoil with and without the 145m-ice shape. To validate the computations, the computed lift coefficients as a function of angle of attack were compared with available experimental data. The ice shapes and the blocking topologies were prepared by NASA Glenn's SmaggIce software. The grid systems were generated by using a four-boundary method based on Hermite interpolation with controls on clustering, orthogonality next to walls, and C continuity across block boundaries. The flow was modeled by the ensemble-averaged compressible Navier-Stokes equations, closed by the shear-stress transport turbulence model in which the integration is to the wall. All solutions were generated by using the NPARC WIND code.

Chi, X.↗
NASA NTRS1975

Stress analysis and stress intensity factors for finite geometry solids containing rectangular surface cracks

The line method of analysis is applied to the Navier-Cauchy equations of elastic equilibrium to calculate the displacement field in a finite geometry bar containing a variable depth rectangular surface crack under extensionally applied uniform loading. The application of this method to these equations leads to coupled sets of simultaneous ordinary differential equations whose solutions are obtained along sets of lines in a discretized region. Using the obtained displacement field, normal stresses and the stress intensity factor variation along the crack periphery are calculated for different crack depth to bar thickness ratios. Crack opening displacements and stress intensity factors are also obtained for a through-thickness, center cracked bar with variable thickness. The reported results show a considerable potential for using this method in calculating stress intensity factors for commonly encountered surface crack geometries in finite solids.

Gyekenyesi, J. P.↗
NASA NTRS1977

Stress analysis and stress-intensity factors for finite geometry solids containing rectangular surface cracks

The line method of analysis is applied to the Navier-Cauchy equations of elastic equilibrium to calculate the displacement field in a finite geometry bar containing a variable depth rectangular surface crack under extensionally applied uniform loading. The application of this method to these equations leads to coupled sets of simultaneous ordinary differential equations whose solutions are obtained along sets of lines in a discretized region. Using the obtained displacement field, normal stresses, and the stress-intensity factor variation along the crack periphery are calculated for different crack depth to bar thickness ratios. Crack opening displacements and stress-intensity factors are also obtained for a through-thickness, center-cracked bar with variable thickness. The reported results show a considerable potential for using this method in calculating stress-intensity factors for commonly encountered surface crack geometries in finite solids

Gyekenyesi, J. P.↗
DOE OSTI2024

Beam Dynamics of the Muon $g\textrm{-}2$ Experiment

The Muon $g\textrm{-}2$ Experiment (E989) at Fermilab aims to measure the muon anomalous magnetic moment $a_{\mu}$ with unprecedented precision, potentially uncovering physics beyond the Standard Model of particle physics. The result based on Runs 1-3, released in 2023, achieved a precision of 0.20 ppm. The experiment circulates muons in a storage ring, measuring $a_{\mu}$ from decay positron time and energy measurements collected with calorimeters. To achieve the required accuracy, it is crucial to measure and control the magnetic field in the ring with high precision. Beam dynamics corrections are necessary for muons not orbiting exactly in the midplane, for their oscillations, and for electric field effects. Highly accurate beam dynamics simulations are instrumental for quantifying and validating the beam dynamics corrections, ultimately improving the precision of the $a_{\mu}$ measurement and facilitating the achievement of the ambitious $70\:\mathrm{ppb}$ systematic uncertainty goal. The measured field data was incorporated into models for simulations using three codes: \texttt{gm2ringsim} (an internal Geant4-based code), \textit{COSY INFINITY}, and \textit{BMAD}. The advantages of \texttt{gm2ringsim} include using CAD-based geometry and modelling the detector effects. \textit{COSY INFINITY} is a highly accurate and efficient code that uses high-order differential-algebraic transfer maps, precise fringe field calculations, and advanced symplectification methods. Symplectification is important for maintaining the physical correctness of the muon beam behaviour with high precision over the storage time, ensuring conservation of phase space volume and preventing artificial damping or excitation of particle motion. The experiment completed its final Run 6 in July 2023, collecting 21 times more data than the previous BNL experiment. Analyses of data from Runs 4-6 are ongoing, with results planned for release in 2025, potentially resolving the current tension between experiment and theory.

43 PARTICLE ACCELERATORS↗
NASA NTRS1996

Fluid Creep Effects on Near-Wall Solute Transport for Non-Isothermal Ampoules

There is a growing practical and theoretical interest in developing accurate macroscopic modelling for flows arising in chemical or physical vapor transport (VT) crystal growth experiments, including those conducted in reduced gravity environments. Rosner was the first person to point out that previously neglected rarefield gas dynamics phenomena (Stefan and bouyancy-driven flows) become rather important sources of convection. In particular, the combination of rarefaction and strong gradients of temperature (and/or concentration) tangential to the side-walls of the ampoule induces convective flows known as thermal (and concentration) 'creep' respectively. His order-of-magnitude estimates revealed that thermal creep effects can be non-negligible even at normal gravitational levels. On the macroscopic level, the bulk fluid mechanics can be adequately described by the familiar macroscopic equations as long as the boundary conditions are modified to account for the integrated effect of kinetic boundary layers adjacent to solid boundaries. Motivated by the growing importance of these phenomena, we have embarked on a series of computational studies to elucidate these fundamental creep-induced effects for a rarefied gas in simple, two-dimensional confined geometries. However, unlike previous related studies, we resort to a microscopic description of the gas, mathematically expressed by the Boltzmann integro-differential equation. We employ the direct simulation Monte Carlo (DSMC) method of Bird, the theoretical foundations and several practical applications. In the case of thermally induced flows, the no-time counter method of Bird is used, as implemented for a hard-sphere gas. The scheme has been also extended to account for realistic molecular interaction models, an extension necessary if the diffusion physics underlying concentration creep are to be captured.

Papadopoulos, Dimitrios↗
NASA NTRS1980

Gigahertz analog modulation and differential delay of GaAlAs lasers - Temperature and current behavior

Gigahertz analog modulation characteristics of broad-area commercially available GaAlAs lasers have been investigated as a function of temperature and current in the vicinity of the upper frequency limit, where the resonance phenomena occur. The optimum temperature for small-signal amplitude modulation was found to be around -15 C for our particular broad-stripe geometry double-heterostructure laser. The Q was found to increase by a factor of 2 and the bandwidth by about 2%; the external quantum efficiency was maximized in this range. The optimum dc current bias was about 2% above the threshold current. Differential delays have also been measured down to a few picosecond accuracy by a unique phase-angle measurement method using a vector voltmeter. Some of the temperature effects observed may be related to mode changes and multimode and superradiance behavior.

Eng, S. T.↗
DOE OSTI2025

Mechanical Properties and Interfacial Bonding of Overmolded Polymer Composite Lattice Structures

This study investigates the mechanical properties and interfacial bonding of Polyamide 12 filled with Glass Fiber (PA12/GF) lattice structures overmolded with Nylon 66 (PA66) and Thermoplastic Polyurethane (TPU). The PA12/GF lattices, designed in Gyroid, Isotruss, and Octahedral geometries, were produced using the Selective Laser Sintering (SLS) technique. The thermal characteristics of both the lattice and overmolding materials were analyzed using Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA). The mechanical performance and interfacial bonding were evaluated through mechanical testing and microstructural analysis. The results indicate that overmolding improved flexural strength and impact resistance of the PA12/GF lattices. For instance, the plain PA12/GF Isotruss lattice exhibited a flexural strength of 15.5 MPa. By overmolding it with TPU the flexural strength increased by up to 137%, while PA66-overmolding resulted in an increase of 371%, achieving a flexural strength of 73 MPa. In terms of impact resistance, TPU-overmolding improved performance significantly, with an increase of 1800% (Gyroid) compared to the plain lattice. Microstructural analysis revealed good adhesion at the interface, especially when both the lattice and overmolding materials were thoroughly dried prior to the overmolding process to minimize interfacial porosity. This study highlights the potential of using overmolding to enhance lattice structures performance, offering lightweight and cost-efficient solutions for automotive applications.

Talabi, Isaac [ORNL] (ORCID:0000000340215594)↗