Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffractive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

Sequential x-ray diffraction topography at 1-BM x-ray optics testing beamline at the advanced photon source

We report progress on implementation and commissioning of sequential X-ray diffraction topography at 1-BM Optics Testing Beamline of the Advanced Photon Source to accommodate growing needs of strain characterization in diffractive crystal optics and other semiconductor single crystals. The setup enables evaluation of strain in single crystals in the nearly-nondispersive double-crystal geometry. Si asymmetric collimator crystals of different crystallographic orientations were designed, fabricated and characterized using in-house capabilities. Imaging the exit beam using digital area detectors permits rapid sequential acquisition of X-ray topographs at different angular positions on the rocking curve of a crystal under investigation. Results on sensitivity and spatial resolution are reported based on experiments with high-quality Si and diamond crystals. The new setup complements laboratory-based X-ray topography capabilities of the Optics group at the Advanced Photon Source.

43 PARTICLE ACCELERATORS↗

Oil-Well Cement and C[subscript 3]S Hydration Under High Pressure as Seen by In Situ X-Ray Diffraction, Temperatures 80[degrees]C with No Additives

The hydration kinetics of a white cement and batches of both Class G and H oil-well cements were examined between 0 and 60 MPa, at {le}80 C, using in situ synchrotron X-ray diffraction. This gives a continuous measure of the C{sub 3}S (Ca{sub 3}SiO{sub 5}), CH (Ca(OH){sub 2}), C{sub 4}AF (Ca{sub 2}FeAlO{sub 5}), ettringite, and other phases in the hydrating slurries. Slurries prepared from single-phase C{sub 3}S; synthetic C{sub 4}AF, and gypsum; and white cement, synthetic C{sub 4}AF and gypsum were also examined. An increasing pressure enhanced the rate of hydration for all slurries. Analysis of the data, using a kinetic model, provided rate constants that were used to obtain activation volumes for C{sub 3}S hydration. For all the cement and C{sub 3}S slurries studied, similar activation volumes were obtained (average {Delta}{double_dagger}{approx}-35 cm{sup 3}/mol), indicating that the presence of cement phases other than C{sub 3}S has a modest influence on the pressure dependence of C{sub 3}S hydration. An alternative analysis, using the time at which 90% of the initial C{sub 3}S remained, gave similar activation volumes. Pressure accelerated the formation of ettringite from synthetic C{sub 4}AF in the presence of gypsum. However, in slurries containing cement, the pressure dependence of C{sub 3}S hydration plays a major role in determining the pressure dependence of ettringite formation.

36 MATERIALS SCIENCE↗

Improvement of Laser Damage Resistance and Diffraction Efficiency of Multilayer Dielectric Diffraction Gratings by HF-Etchback Linewidth Tailoring

Multilayer dielectric (MLD) diffraction gratings for Petawatt-class laser systems possess unique laser damage characteristics. Details of the shape of the grating lines and the concentration of absorbing impurities on the surface of the grating structures both have strong effects on laser damage threshold. It is known that electric field enhancement in the solid material comprising the grating lines varies directly with the linewidth and inversely with the line height for equivalent diffraction efficiency. Here, they present an overview of laser damage characteristics of MLD gratings, and describe a process for post-processing ion-beam etched grating lines using very dilute buffered hydrofluoric acid solutions. This process acts simultaneously to reduce grating linewidth and remove surface contaminants, thereby improving laser damage thresholds through two pathways.

42 ENGINEERING↗

Stress distribution during cold compression of a quartz aggregate using synchrotron X-ray diffraction: Observed yielding, damage, and grain crushing

Herein, we report new experimental results that quantify the stress distribution within a quartz aggregate during pore collapse and grain crushing. The samples were probed with synchrotron X-ray diffraction as they were compressed in a multianvil deformation apparatus at room temperature from low pressure (tens of megapascal) to pressures of a few gigapascal. In such a material, stress is likely to concentrate at grain-to-grain contacts and vanish where grains are bounded by open porosity. Therefore, internal stress is likely to vary significantly from point to point in such an aggregate, and hence, it is important to understand both the heterogeneity and anisotropy of such variation with respect to the externally applied stress. In our quartz aggregate (grain size of ~4 μm), the measured diffraction peaks broaden asymmetrically at low pressure (tens of megapascal), suggesting that open pores are still a dominant characteristic of grain boundaries. In contrast, a reference sample of novaculite (a highly dense quartz polycrystal, grain size of ~6–9 μm) showed virtually no peak broadening with increasing pressure. In the quartz aggregate, we observed significant deviation in the pressure-volume curves in the range of P = 400–600 MPa. We suggest that this marks the onset of grain crushing (generally denoted as P* in the rock mechanic literature), which is commonly reported to occur in sandstones at pressures of this order, in general agreement with a Hertzian analysis of fracturing at grain contacts.

58 GEOSCIENCES↗

Synchrotron-based diffraction-enhanced imaging and diffraction-enhanced imaging combined with CT X-ray imaging systems to image seeds at 30 keV

Utilized the upgraded Synchrotron-based non-destructive Diffraction-enhanced imaging and Diffraction-enhanced imaging coupled with CT X-ray imaging systems to image the chickpea seeds, to enhance the contrast in plant root architecture, visibility of fine structures of root architecture growth and some aspects of physiology at acceptable level. DEI-CT images were acquired with 30 keV synchrotron X-rays. A series of DEI-CT slices were assembled together, to form a 3D data set. DEI-CT images explored more structural information and morphology. Noticed detailed anatomical, physiological observations, and contrast mechanisms. Furthermore, with these systems, some of the complex plant traits, root morphology, growth of laterals and subsequent laterals can be visualized directly.

36 MATERIALS SCIENCE↗

Relationships Between the Phase Transformation Kinetics, Texture Evolution, and Microstructure Development in a 304L Stainless Steel Under Biaxial Loading Conditions: Synchrotron X-ray and Electron Backscatter Diffraction Studies

The relationships between the martensitic phase transformation kinetics, texture evolution, and the microstructure development in the parent austenite phase were studied for a 304L stainless steel that exhibits the transformation-induced plasticity effect under biaxial loading conditions at ambient temperature. The applied loading paths included: pure torsion, simultaneous biaxial torsion/tension, simultaneous biaxial torsion/compression, and stepwise loading of tension followed by torsion (i.e., first loading by uniaxial tension and then by pure torsion in sequence). Synchrotron X-ray and electron backscatter diffraction techniques were used to measure the evolution of the phase fractions, textures, and microstructures as a function of the applied strains. The influence of loading character and path on the changes in martensitic phase transformation kinetics is discussed in the context of (1) texture-transformation relationship and the preferred transformation of grains belonging to certain texture components over the others, (2) effects of axial strains on shear band evolutions, and (3) volume changes associated with martensitic transformation.

Complex Loading↗

Deformation mechanisms in a precipitation-strengthened ferritic super alloy revealed by in situ neutron dffraction studies at elevated temperatures

The ferritic superalloy Fe–10Ni–6.5Al–10Cr–3.4Mo strengthened by ordered (Ni,Fe)AlB2-type precipitates is a candidate material for ultra-supercritical steam turbine applications above 923 K. Despite earlier success in improving its room-temperature ductility, the creep resistance of this material at high temperatures needs to be further improved, which requires a fundamental understanding of the high-temperature deformation mechanisms at the scales of individual phases and grains. In situ neutron diffraction has been utilized to investigate the lattice strain evolution and the microscopic load-sharing mechanisms during tensile deformation of this ferritic superalloy at elevated temperatures. Finite-element simulations based on the crystal plasticity theory are employed and compared with the experimental results, both qualitatively and quantitatively. Based on these interphase and intergranular load-partitioning studies, it is found that the deformation mechanisms change from dislocation slip to those related to dislocation climb, diffusional flow and possibly grain boundary sliding, below and above 873 K, respectively. Insights into microstructural design for enhancing creep resistance are also discussed.

nuclear (including radiation effects), defects, me↗

Individual phase constitutive properties of a TRIP-assisted QP980 steel from a combined synchrotron X-ray diffraction and crystal plasticity approach

Microstructure-based constitutive models for multiphase steels require accurate constitutive properties of the individual phases for component forming and performance simulations. We address this requirement with a combined experimental/theoretical methodology which determines the critical resolved shear stresses and hardening parameters of the constituent phases in QP980, a TRIP assisted steel subject to a two-step quenching and partitioning heat treatment. High energy X-Ray diffraction (HEXRD) from a synchrotron source provided the average lattice strains of the ferrite, martensite, and austenite phases from the measured volume during in situ tensile deformation. The HEXRD data was then input to a computationally efficient, elastic-plastic self-consistent (EPSC) crystal plasticity model which estimated the constitutive parameters of different slip systems for the three phases via a trial-and-error approach. The EPSC-estimated parameters are then input to a finite element crystal plasticity (CPFE) model representing the QP980 tensile sample. The predicted lattice strains and global stress versus strain curves are found to be 8% lower that the EPSC model predicted values and from the HEXRD measurements, respectively. This discrepancy, which is attributed to the stiff secant assumption in the EPSC formulation, is resolved with a second step in which CPFE is used to iteratively refine the EPSC-estimated parameters. Remarkably close agreement is obtained between the theoretically-predicted and experimentally derived flow curve for the QP980 material.

Hu, X. H. (ORCID:0000000277355091)↗

Micrometer-scale 3-D shape characterization of eight cements: Particle shape and cement chemistry, and the effect of particle shape on laser diffraction particle size measurement

Eight different portland cements were imaged on a synchrotron beam line at Brookhaven National Laboratory using X-ray microcomputed tomography at a voxel size of about 1 mum per cubic voxel edge. The particles ranged in size roughly between 10 mum and 100 mum. The shape and size of individual particles were computationally analyzed using spherical harmonic analysis. The particle shape difference between cements was small but significant, as judged by several different quantitative shape measures, including the particle length, width, and thickness distributions. It was found that the average shape of cement particles was closely correlated with the volume fraction of C{sub 3}S (alite) and C{sub 2}S (belite) making up the cement powder. It is shown that the non-spherical particle shape of the cements strongly influence laser diffraction results, at least in the sieve size range of 20 mum to 38 mum. Since laser diffraction particle size measurement is being increasingly used by the cement industry, while cement chemistry is always a main factor in cement production, these results could have important implications for how this kind of particle size measurement should be understood and used in the cement industry.

36 MATERIALS SCIENCE↗

Application of micro X-ray diffraction to investigate the reaction products formed by the alkali–silica reaction in concrete structures

Alkali–silica reaction (ASR) is one of the most important deterioration mechanisms in concrete leading to substantial damages of structures worldwide. Synchrotron-based micro-X-ray diffraction (micro-XRD) was employed to characterize the mineral phases formed in micro-cracks of concrete aggregates as a consequence of ASR. This high spatial resolution technique enables to directly gain structural information on ASR products formed in a 40-year old motorway bridge damaged due to ASR. Micro-X-ray-fluorescence was applied on thin sections to locate the reaction products formed in veins within concrete aggregates. Micro-XRD pattern were collected at selected points of interest along a vein by rotating the sample. Rietveld refinement determined the structure of the ASR product consisting of a new layered framework similar to mountainite and rhodesite. It is conceivable that understanding the structure of the ASR product may help developing new technical treatments inhibiting ASR.

36 MATERIALS SCIENCE↗

Monitoring the methanol conversion process in H-ZSM-5 using synchrotron X-ray powder diffraction-mass spectrometry

By monitoring the catalytic conversion of methanol using operando synchrotron powder X-ray diffraction (SXRD) and structure refinement, in combination with theoretical calculations, we demonstrate for the first time, that the concerted associative mechanism is responsible for dimethyl ether production via an activated protonated methanol intermediate species over H-ZSM-5 in an early stage of reaction at 200 °C. The minor contribution from the dissociative mechanism of the adsorbed methoxy intermediate species at Brønsted acid sites, renders their accumulation during the late stage of reaction, which leads to a build-up of the ‘hydrocarbon pool’ and eventually to ‘carbon’ through the formation of C-C bonds.

Lo, Benedict T W.↗

An X-ray diffraction study of pressure-induced phase transitions in Bi{sub 2}MoO{sub 6}

Synchrotron based X-ray diffraction through a diamond anvil cell was used to determine the equations of state and pressure-induced phase transitions in Bi{sub 2}MoO{sub 6}. It was observed that Bi{sub 2}MoO{sub 6} undergoes a phase transformation at {approx}6.8 GPa. The high-pressure phase can be indexed to the orthorhombic structure and the transition is reversible on decompression from {approx}47 GPa. The bulk moduli of the low and high-pressure phases were calculated, while holding K Prime =4, to be: K=51{+-}1 GPa and K=141.5 {+-}0.1 GPa, respectively. - Graphical abstract: The material Bi{sub 2}MoO{sub 6} was placed inside a diamond anvil cell and then studied under high pressure at beamline X17C of the National Synchrotron Light source. X-ray diffraction data was analyzed using the Rietveld method. Highlights: Black-Right-Pointing-Pointer A high-pressure study of bismuth molybdate was performed. Black-Right-Pointing-Pointer Pressure-induced phase transitions were observed. Black-Right-Pointing-Pointer The low pressure phase bulk modulus was calculated to be K=51{+-}1 GPa. Black-Right-Pointing-Pointer The high pressure phase bulk modulus was calculated to be B=141.5{+-}0.1 GPa.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synchrotron X-ray diffraction study of zirconium hydride distribution in Zr-2.5%Nb and its redistribution during thermal cycling

Highlights: • Differently oriented grains were studied in situ using synchrotron diffraction. • The effect of thermo-mechanical history on hydrogen location in α-Zr is considered. • Hydrogen redistribution in alpha-Zr matrix during thermal cycling discussed. - Abstract: Hydride distribution in a dual-phase hydrided Zr-2.5wt%Nb has been studied. Samples having different prior thermo-mechanical processing history were thermally cycled within a 86 keV X-ray photon beam. The diffraction patterns generated with this technique allow the evaluation of the relative quantity of hydrides within differently oriented grain sets. It was found that hydrides exist primarily within two different α-Zr grain-sets. One grain-set has its {0002} α-Zr direction oriented very close to the hoop direction while the other exists within a plane approximately 20° away from it. During thermal cycling, the proportion or hydrides oriented within different grain sets was shown to change from the distribution associated with the prior thermomechanical processing, to that corresponding to the current thermal cycling conditions. It was also shown that the ability for hydrogen to redistribute in the matrix correlates with the cooling rate of the specimen.

36 MATERIALS SCIENCE↗