Search NASA⌕ Search

SEARCH · Search NASA

Results for “Directional solidification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Selective laser melting of 304L stainless steel: Role of volumetric energy density on the microstructure, texture and mechanical properties

The role of volumetric energy density on the microstructural evolution, texture and mechanical properties of 304L stainless steel parts additively manufactured via selective laser melting process is investigated. 304L is chosen because it is a potential candidate to be used as a matrix in a metal matrix composite with nanoparticles dispersion for energy and high temperature applications. The highest relative density of 99 %±0.5 was achieved using a volumetric energy density of 1400 J/mm 3 . Both XRD analysis and Scheil simulation revealed the presence of a small trace of the delta ferrite phase, due to rapid solidification within the austenitic matrix of 304L. Here, a fine cellular substructure ranged between 0.4–1.8 μm, was detected across different energy density values. At the highest energy density value, a strong texture in the direction of [100] was identified. At lower energy density values, multicomponent texture was found due to high nucleation rate and the existing defects. Yield strength, ultimate tensile strength, and microhardness of samples with a relative density of 99 % were measured to be 540 ± 15 MPa, 660 ± 20 MPa and 254 ± 7 HV, respectively and higher than mechanical properties of conventionally manufactured 304L stainless steel. Heat treatment of the laser melted 304L at 1200 °C for 2 h, resulted in the nucleation of recrystallized equiaxed grains followed by a decrease in microhardness value from 233 ± 3 HV to 208 ± 8 HV due to disappearance of cellular substructure.

304L stainless steel↗
DOE OSTI2023

Leveraging the Polymer Glass Transition to Access Thermally Switchable Shear Jamming Suspensions

Suspensions of polymeric nano-and microparticles are fascinating stress-responsive material systems that, depending on their composition, can display a diverse range of flow properties under shear, such as drastic thinning, thickening, and even jamming (reversible solidification driven by shear). However, investigations to date have almost exclusively focused on nonresponsive particles, which do not allow in situ tuning of the flow properties. Polymeric materials possess rich phase transitions that can be directly tuned by their chemical structures, which has enabled researchers to engineer versatile adaptive materials that can respond to targeted external stimuli. Reported herein are suspensions of (readily prepared) micrometer-sized polymeric particles with accessible glass transition temperatures (T g ) designed to thermally control their non-Newtonian rheology. The underlying mechanical stiffness and interparticle friction between particles change dramatically near T g . Capitalizing on these properties, it is shown that, in contrast to conventional systems, a dramatic and nonmonotonic change in shear thickening occurs as the suspensions transition through the particles' T g . This straightforward strategy enables the in situ turning on (or off) of the system's ability to shear jam by varying the temperature relative to T g and lays the groundwork for other types of stimuli-responsive jamming systems through polymer chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Accounting for Melt Flow Pattern and Solid Fraction Evolution in DC Casting of Al-Cu Alloy Using v{sup 2}−f Turbulence Model

Experimental techniques remain reliable approaches for investigating the effects of parameters of the direct chill (DC) casting process on macrosegregation, grain structure formation, and surface quality. However, experimental analysis methods of these effects are expensive and can often prove difficult to implement. Understanding of the complex physics of the solidification process remains limited, and this makes it indispensable to use accurate numerical modeling tools as a complement to experiments. Numerical modeling without consideration of turbulent flow is unsuitable for application to solidification occurring during DC casting, since significant turbulent flow exists in the upper section of the cast, where the liquid pool exists. The present work employed a low-Re v{sup 2}−f turbulence model and a dual-zone solidification flow model to predict the melt flow pattern, turbulence level, sump depth, transition zone thickness, and mushy zone thickness in the DC casting of Al-Cu alloy. The obtained results provided evidence of significant damping of the flow in the slurry zone. Furthermore, results of different simulation cases revealed a narrower transition zone and shallower sump.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Directed energy deposition of radially functionally graded nickel based superalloys IN625 and IN738: Microstructure and mechanical properties

This study investigates the microstructure and mechanical properties of radially functionally graded (RFG) materials fabricated from nickel-based superalloys IN625 and IN738 using directed energy deposition (DED). RFG cylindrical deposits with radial gradients of IN625-IN738 and IN738-IN625 were successfully fabricated and confirmed to be crack-free through tailored composition grading, scan strategy and process parameters that minimized thermal gradients and solidification velocities. Microstructural analysis revealed distinct variations across the gradient, characterized by differences in dendrite arm spacing, microsegregation, and the formation of distinct γ' precipitates and carbide/boride phases (MC, M 6 C, M 2 C, and MB 2 ) in as-deposited (AD) conditions, which evolved into M 23 C 6 and M 2 B upon subsequent heat treatment (HT). EBSD showed predominant columnar grains with a [100] texture, while microhardness profiles demonstrated consistent variation across the gradients. Mechanical testing highlighted the synergy of the graded structure, combining IN738's strength with IN625's ductility, resulting in enhanced properties such as a yield strength of 1131 MPa, ultimate tensile strength of 1382 MPa, and elongation of 12 % for HT IN625-IN738 grading. Numerical simulations employing CALPHAD thermodynamic calculations and finite element thermal modeling are used to establish phase evolution and microstructural feature correlation with thermal profiles, aiding in the optimization of process-structure-property relationship.

Additive manufacturing↗
DOE OSTI2017

Powder bed binder jet 3D printing of Inconel 718: Densification, microstructural evolution and challenges

Traditional manufacturing of Inconel 718 components from castings and thermomechanical processing routes involve extensive post processing and machining to attain the desired geometry. Additive manufacturing (AM) technologies including direct energy deposition (DED), selective laser melting (SLM), electron beam melting (EBM) and binder jet 3D printing (BJ3DP) can minimize scrap generation and reduce lead times. While there is extensive literature on the use of melting and solidification based AM technologies, there has been limited research on the use of binder jet 3D printing. In this paper, a brief review on binder jet additive manufacturing of Inconel 718 is presented. In addition, existing knowledge on sintering of Inconel 718 has been extended to binder jet 3D printing. We found that supersolidus liquid phase sintering (SLPS) is necessary to achieve full densification of Inconel 718. SLPS is sensitive to the feedstock chemistry that has a strong influence on the liquid volume fraction at the processing temperature. Based on these results, we discuss an empirical framework to determine the role of powder particle size and liquid volume fraction on sintering kinetics. In conclusion, the role of powder packing factor and binder saturation on microstructural evolution is discussed. The current challenges in the use of BJ3DP for fabrication of Inconel 718, as well as, extension to other metal systems, are presented.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Atomistic to continuum modeling of solidification microstructures

We summarize recent advances in modeling of solidification microstructures using computational methods that bridge atomistic to continuum scales. We first discuss progress in atomistic modeling of equilibrium and non-equilibrium solid–liquid interface properties influencing microstructure formation, as well as interface coalescence phenomena influencing the late stages of solidification. The latter is relevant in the context of hot tearing reviewed in the article by M. Rappaz in this issue. We then discuss progress to model microstructures on a continuum scale using phase-field methods. We focus on selected examples in which modeling of 3D cellular and dendritic microstructures has been directly linked to experimental observations. Finally, we discuss a recently introduced coarse-grained dendritic needle network approach to simulate the formation of well-developed dendritic microstructures. The approach reliably bridges the well-separated scales traditionally simulated by phase-field and grain structure models, hence opening new avenues for quantitative modeling of complex intra- and inter-grain dynamical interactions on a grain scale.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The microstructure of a selective laser melting (SLM)-fabricated NiTi shape memory alloy with superior tensile property and shape memory recoverability

A selective laser melting (SLM)-fabricated NiTi with superior tensile property and shape memory recoverability was obtained by using a unique stripe rotation scanning strategy. Here, the alloy characteristics, formation mechanisms and evolution in terms of twins, dislocations and precipitations of the alloy were systematically studied. Compared to the conventional smelting-followed-by-machining, the SLM fabrication process involves rapid solidification and repeated heating, which confer distinctive characteristics to the microstructures of SLM-fabricated NiTi alloys. Rapid solidification promotes the formation of a supersaturation solid solution matrix containing a high concentration vacancies, which in turn aggregate to generate a high density of dislocations. During subsequent repeated heating stages, these dislocations occur thermal motion along three directions of <001 > , <111> and <110 >, leading to the formation of thermal kinks, helical dislocations and wave morphology. Simultaneously, precipitated particles Ti 3 Ni 4 repeatedly nucleate and heterogeneous grow with the movement of dislocation. Such precipitation behavior, termed repeated precipitation, has not been previously reported in the conventional NiTi alloys, suggesting that it could be a unique characteristic of such alloy. After martensitic transformation, only two twins, {1 1¯ 1} type I twin and compound twin, are detected. The twinning lamellae of these two twins, where precipitation and dislocation pile-ups exist, often have uneven thickness and chaotic arrangement. Besides, the unique self-accommodated microstructures, such as secondary {1 1¯ 1} type I twin and compound twin with “herring-bone’’ lamellae, which often appear in the deformed or nanocrystalline NiTi, can also be observed. These unique microstructures may confer the distinctive properties to the SLM-fabricated NiTi.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Laser Powder Directed Energy Deposition of Steels for Nuclear Applications

This comprehensive investigation examines the structure–property relationships in two nuclear alloy systems—Alloy 709 (A709) austenitic stainless steel and Grade 92 (G-92) ferritic/martensitic (F/M) steel—manufactured via directed energy deposition (DED) for sodium-cooled fast reactor applications. This study establishes the fundamental mechanisms for controlling microstructures for optimizing the mechanical performance of additively manufactured nuclear materials through systematic heat treatment optimization and multiscale characterization. As-deposited A709 steel develops a complex multiscale strengthening architecture consisting of a fine cellular solidification structure with diameter of 2-3 µm within10–50 µm grains, elevated dislocation densities from rapid thermal cycling, and grain boundary precipitates that activate concurrent Hall–Petch, dislocation, and precipitation hardening mechanisms to achieve exceptional properties [yield strength (YS): 603 MPa, ultimate tensile strength (UTS): 844 MPa, Vickers hardness: 220 HV] that achieve a 44% superior strength compared to that of the wrought material. Heat treatments produce different results. Solution annealing (SA) dissolves the cellular structure and reduces the hardness to 190 HV. Precipitation treatment (PT) keeps the cellular structure but adds carbides, allowing the hardness to reach 205 HV. The best approach combines both treatments (SA+PT) and creates uniform precipitate distributions with M 23 C 6 carbides at the grain boundaries and MX carbonitrides in the matrix, achieving a hardness of 195 HV. However, directional differences persist, with a 12%–15% strength variation between orientations due to the inherited layered microstructural architecture that survives aggressive heat treatment. While tensile testing at 550°C demonstrates 40%–50% thermal softening with dynamic strain aging, DED A709 steel still maintains a 71% higher YS than that of the wrought material. Ion irradiation studies (100–400 dpa) of DED A709 steel reveal progressive radiation damage with increasing void density and radiation-induced segregation causing nickel enrichment and chromium depletion, which will ultimately compromise mechanical properties. As-deposited G-92 exhibits exceptional strength (UTS: 1650–1700 MPa, 430 HV) through a complex microstructure containing both ferrite and martensite phases, a high geometrically necessary dislocation (GND) density (17.04×10 14 /m 2 ), and fine carbides. Heat treatments create distinct changes. Normalizing produces fresh martensite with the highest hardness (460 HV) and an increased GND density (20.23×10 14 /m 2 ). Tempering develops dual precipitation systems and reduces the hardness to 290 HV. The optimal approach uses sequential normalizing plus tempering, achieving balanced properties with the lowest hardness (250 HV) and a reduced GND density (11.01×10 14 /m 2 ). A processing-dependent anisotropy is observed: horizontal specimens achieve superior ductile behavior, while vertical specimens exhibit brittle failure. A tempering heat treatment successfully mitigates this anisotropic behavior by transforming the hard martensitic as-deposited structure into tempered martensite enabling both horizontal and vertical specimens to exhibit similar stress–strain characteristics with visible necking behavior. Remarkably, testing at 550°C reveals a reversal in the anisotropy, where as-deposited specimens achieve near isotropy with superior thermal stability (a 15%–20% strength reduction), while tempered specimens develop an orientation dependence with a 25%–30% strength reduction. Both alloy systems demonstrate that DED processing creates specimens with a superior strength through refined microstructural features, though with distinct strengthening mechanisms—austenitic through cellular structures and precipitates versus F/M through phase transformations and precipitates. Heat treatment optimization requires alloy-specific approaches, with A709 benefiting from controlled precipitation while G-92 requires careful phase transformation control. The results show that DED manufacturing can produce nuclear materials with exceptional performance, but directional effects and temperature-dependent behavior must be carefully considered for reactor component design and qualification.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2018

Thermomechanical Processing of Metal Feedstock for Semisolid Forming: A Review

Thermomechanical processing of cast structures is an effective solid working route of generating thixotropic morphologies after subsequent partial melting and is in use for decades to manufacture the bulk billet feedstock for thixoforming from a variety of alloys. The solid-state deformation is also critical for coarse particulate feedstock, utilized for semisolid forming either directly or after compaction into billets. Although the original concept, called strain-induced melt activation (SIMA), defined the specific procedure, the term became generally recognized synonym for a variety of thermomechanical treatments offering an opportunity of controlling the solidification microstructure. This review covers transformations during solid-state deformation, reheating to semisolid state and isothermal holding within solidus–liquidus range, and solidification of thixotropic slurries. Essentials of semisolid metal processing, necessary to understand the subject, are supported by details related to specific implementation techniques and alloys. Application examples at laboratory and commercial levels and properties achieved with conventional and severe plastic deformation techniques, for different alloys along with present limitations, are described. The link between solid-state deformation-enhanced melting and liquid metal engineering is emphasized throughout the paper in terms of the common goal of controlling the solidification outcome in order to develop technology for mass-scale production of net-shape components having performance characteristics superior to conventional castings.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Fatigue and Fracture Behavior of Additively Manufactured Austenitic Stainless Steel

Additive manufacturing (AM) includes a diverse suite of innovative manufacturing processes for producing near-net shape components, typically from powder or wire feedstock. Reported mechanical properties of AM materials vary significantly depending on the details of the manufacturing process and the characteristics of the processing defects (namely, lack of fusion defects). However, an excellent combination of strength, ductility and fracture resistance can be achieved in AM type 304L and 316L austenitic stainless steels by minimizing processing defects. It is also important to recognize that localized solidification processing during AIVI produces microstructures more analogous to weld microstructures than wrought microstructures. Consequently, the mechanical behavior of AM austenitic stainless steels in harsh environments can diverge from the performance of wrought materials. This report gives an overview of the fracture and fatigue response of type 304L materials from both directed energy deposition (DED) and powder bed fusion (PBF) techniques. In particular, the mechanical performance of these materials is considered for high-pressure hydrogen applications by evaluating fatigue and fracture resistance after thermally precharging of test specimens in high-pressure gaseous hydrogen. The mechanical behaviors are considered with respect to previous reports on hydrogen-assisted fracture of austenitic stainless steel welds and the unique characteristics of the AM microstructures. Fatigue crack growth can be relatively insensitive to processing defects, displaying similar behavior as wrought materials. Fracture resistance of dense AM austenitic stainless steel, on the other hand, is more consistent with weld metal than with compositionally-similar wrought materials. Hydrogen effects in the AM materials are generally more severe than in wrought materials, but comparable to measurements on welded austenitic stainless steels in hydrogen environments. While hydrogenassisted fracture manifests differently in welded and AM austenitic stainless steel, the fracture process appears to have a common origin in the compositional microsegregation intrinsic to solidification processes.

additive manufacturing, austenitic stainless steel↗
DOE OSTI2016

Impact of gravity on hydrate saturation in gas‐rich environments

Abstract We extend a one‐dimensional analytical solution by including buoyancy‐driven flow to explore the impact of gravity on hydrate formation from gas injection into brine‐saturated sediments within the hydrate stability zone. This solution includes the fully coupled gas and liquid phase flow and the associated advective transport in a homogeneous system. We obtain the saturations assuming Darcy flow under combined pressure and gravity gradients; capillary forces are neglected. At a high gas supply rate, the overpressure gradient (gradient of water pressure deviation from the hydrostatic pressure) dominates the gas flow, and the hydrate saturation is independent of the flow rate and flow direction. At a low gas supply rate, the buoyancy (the drive for gas flow induced by the density difference between gas and liquid) dominates the gas flow, and the hydrate saturation depends on the flow rate and flow direction. Hydrate saturation is highest for upward flow, and lowest for downward flow. Hydrate saturation decreases with flow rate for upward flow, and increases with flow rate for downward flow. In all cases, hydrate saturation is constant behind the hydrate solidification front. Gas saturation is homogeneous and close to the residual value for upward flow at a low rate; gas flows at the rate it is supplied. Gas saturation is much greater than the residual value, and decreases from the gas inlet to the hydrate solidification front for downward flow at a very low rate. The effect of gravity is usually negligible in laboratory experiments, yet is significant in natural hydrate systems.

You, Kehua↗
DOE OSTI2017

Formation of high concentrations of isolated Zn vacancies and evidence for their acceptor levels in ZnO

Here, research is described here that is directed toward obtaining p -type ZnO crystals either by doping or by creating native defects. Theoretically, zinc vacancies are shallow acceptors that should allow for p -type conduction. Bulk ZnO crystals can be grown by chemical vapor transport (CVT), melt solidification, and hydrothermal methods. Here we have explored annealing processes with the goal of creating zinc vacancies in bulk ZnO crystals. Positron annihilation spectra reveal the reproducible formation of high concentrations (>10 20 cm –3 ) of isolated zinc vacancies ( V Zn ) in oxygen-annealed, CVT-grown ZnO crystals in the ~100–150 nm near-surface. Melt- and hydrothermally grown samples, in contrast, show insignificant levels of zinc vacancy creation. Photoluminescence (PL) emission spectra indicate a V Zn (0/-1) acceptor level at ~ 155–165 meV; red PL (~1.7 eV) emission, related to the V Zn (-1/-2) level, was also observed. Infrared absorption spectroscopy reveals the presence of a zinc vacancy complex with a hole binding energy range of 420–450 meV – and with a continuum suggesting a p -type region. XPS measurements support the deficiency of Zn after oxygen annealing the CVT-grown ZnO single crystal.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Structural Dynamics in UV Curable Resins Resolved by In Situ 3D Printing X-ray Photon Correlation Spectroscopy

Additive manufacturing (AM) is a promising technique to rapidly produce polymeric materials into complex 3-dimensional (3D) geometries. While AM is widespread and relevant for a range of applications, implementation in industry has outpaced our fundamental understanding of polymer dynamics and structure development during the printing process. Characterization and quantification of such dynamics is necessary to optimize final material properties and design future materials and processes for 3D printing. Here, we utilize X-ray photon correlation spectroscopy (XPCS) to measure spatial and time-resolved, out-of-equilibrium dynamics during direct ink write (DIW) 3D printing. Specifically, we investigate the progression of structural dynamics in a dual cure (UV/thermal) nanocomposite during and directly after printing. As the filament is printed and cured in situ, the relaxation processes of the cross-linking network are measured through the dynamics of inorganic filler particles. The characteristic relaxation time of the dynamics is calculated through the intensity–intensity autocorrelation function g 2 and directly correlated to the printing process parameters, such as printhead velocity and UV light intensity. The time-resolved evolution of nanoscale dynamics follows a power-law dependence as the filament is cured. Additionally, bulk rheological characterizations reveal the macroscopic solidification of the resin, providing correlation of material properties across a wide range of length and time scales. Overall, the measurement of multiscale, out-of-equilibrium dynamics provides insight into the development of structure in polymer nanocomposite filaments during 3D printing and is used to further understand the influence of such parameters on the AM process.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Use of Robotics in Liquid Waste System - {sup 3}H Evaporator, Tank Closure and Defense Waste Processing Facility - 18525

The Savannah River Site (SRS) Liquid Waste System (LWS) safely stores and treats high-level radioactive waste. The LWS consists of 51 waste storage tanks (eight of which are operationally closed and filled with grout), waste evaporators, treatment facilities, and solidification facilities such as the Defense Waste Processing Facility (DWPF) and Salt-stone Production Facility (SPF). At Savannah River Remediation (SRR), the liquid waste contractor, robotic technologies are needed to enter areas and spaces that are otherwise inaccessible or prohibit direct access by workers due to unsafe, unstable, or unknown physical or structural conditions; or configurations that are hard to reach or beyond reach without taking extraordinary mechanical measures. As discussed below, SRR uses robotic technologies at various LWS facilities to reduce dose to the workers as well as provide access to unreachable locations due to the presence of radiological or chemical hazards. (author)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2018

A novel interface strengthening layer: Nanoscale AuCu super-structure formed during Au80Sn20/Cu rapid solidification soldering process

Highlights: • The nanoscale AuCu super-structure formed in Au80Sn20/Cu soldering joint. • The phase-transformation diffusion mechanism of Au80Sn20/Cu soldering process was studied. • The orientation relationship of Au80Sn20/Cu intermetallic compounds was investigated. • The interfacial strengthening mechanism of nanoscale AuCu layer was discussed. - Abstract: Phase composition and orientation of intermetallic compounds layers determine the functional and mechanical properties of solder joints. In this paper, interfacial reaction and strengthening mechanism of Au80Sn20/Cu joint by rapid solidification reflow soldering were studied. The Au80Sn20/Cu solder joint by rapid solidification reflow soldering exhibit a superior shear property, and the shear strength reaches up to 90 MPa. It is found that a new nanoscale AuCu super-structure formed in the interfacial intermetallic compounds layer, which is coherent with the [001] Cu substrate. The orientation relationship of Cu matrix/interfacial intermetallic compounds is determined to be [001]{sub Cu}∥[001]{sub AuCu}∥[ 2-bar 4 2-bar 3]{sub (AuCu){sub 5Sn}} and (200){sub Cu}∥(200){sub AuCu}∥(10 1-bar 0){sub (AuCu){sub 5Sn}}. Nanoscale AuCu super-structure influences the interface slip direction and provides interface misfit dislocation, hinder the dislocation movement, lead to the interface strengthening effect. Our finding on nanoscale AuCu super-structure formed during Au80Sn20/Cu soldering process not only sheds light on future research direction but also provides practical guidance to the engineers in solder industry.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

An in situ imaging investigation of the effect of gas flow rates on directed energy deposition

Gas flow rates in Directed Energy Deposition (DED) Additive Manufacturing (AM) can significantly affect the quality of built parts by altering melt pool geometry. Using a DED process replicator and in situ synchrotron radiography, together with analogous experiments in an industrial DED machine, we investigate the impact of carrier gas and shield gas flow rates on build quality. The results reveal that there is a critical shield gas flow rate above which melt pools are flattened, tracks widen, and thus layer thickness decreases. The reduction in layer thickness is most prominent in conditions with low carrier gas flow rate, as the highly turbulent shield gas flow may divert slow moving powder particles away from the melt pool, decreasing capture efficiency. Very high flow rates increase internal porosity, as fast-moving particles impacting the melt pool surface can entrain chamber gas behind them. High gas flow rates also cool the melt pool, creating shallower melt pools with increased thermal gradients near the solidification front, increasing pore entrapment in the solidified track.

Additive manufacturing↗
DOE OSTI2022

Crack-Free 30% Chromium-Nickel Alloy Welding Products for Nuclear Service

We report prior research in the development of 30% chromium-nickel alloy nuclear welding wires has resulted in the resolution of primary water stress corrosion cracking (PWSCC) and ductility dip cracking (DDC) as well as improvement in solidification cracking (SC) resistance. The resolution of DDC exhibits some Laves phase, which has a negative effect on SC resistance. In this study, the use of an alternate carbide former, tantalum (Ta), in combination with niobium (Nb) was researched. Three heats of recently designed Filler Metal 52MSS-Ta (i.e., HV1648, HV1673A, and VX131WXW) were melted, fabricated, and systematically studied. DDC and SC were evaluated with thermodynamic modeling using the Scheil solidification simulation model, two types of varestraint tests, and strain-to-fracture (STF) testing. The varestraint and STF test results showed an improved SC resistance with reduced Laves phase and concurrent excellent DDC resistance. Optimized compositions with low Laves phase also exhibited high threshold strain values (TSVs) in the STF test. VX131WXW — which contains 2.81 wt-% Ta, 0.6 wt-% Nb, and 6 wt-% iron (Fe) - exhibited a TSV of 24%. Thermo-Calc computed the Laves phase to be 0.24% for VX131WXW compared to 0.06% in HV1673A. This difference in Laves phase resulted in the lower SC resistance of VX131WXW compared to HV1673A when measured with longitudinal varestraint testing. The maximum crack distance for HV1673A was about 0.6 mm while that of heat VX131WXW was about 1.0 mm. The typical diluted weld deposit made with VX131WXW was also resistant to PWSCC due to the chromium content exceeding 24%. These simultaneous results mark progress toward crack-free welds and provide direction for further optimization of Ta-containing filler metals.

30% chromium-nickel alloy↗