Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dislocation structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

The high temperature deformation in cyclic loading of a single crystal nickel-base superalloy

The high temperature cyclic stress softening response of the single crystal nickel-base superalloy PWA 1480 was investigated. Specimens oriented near the 001- and 111-lines were tested at 1050 C in low-cycle fatigue and then microstructurally evaluated. The 001- and 111-line specimens had dissimilar flow behavior in monotonic tensile tests, but comparable softening in low-cycle fatigue. This softening was accompanied by rapid generation of dislocation networks at the gamma-gamma-prime interfaces and by a slower time-dependent coarsening of gamma-prime precipitates. Due to the rapid formation of a dislocation substructure at the gamma-gamma-prime interfaces, the cyclic stress softening could be modeled with an existing theory which related cyclic stress to the evolving microstructure and dislocation structure.

Gabb, T. P.↗

Creep substructure formation in sodium chloride single crystals in the power law and exponential creep regimes

Creep tests conducted on NaCl single crystals in the temperature range from 373 to 1023 K show that true steady state creep is obtained only above 873 K when the ratio of the applied stress to the shear modulus is less than or equal to 0.0001. Under other stress and temperature conditions, corresponding to both power law and exponential creep, the creep rate decreases monotonically with increasing strain. The transition from power law to exponential creep is shown to be associated with increases in the dislocation density, the cell boundary width, and the aspect ratio of the subgrains along the primary slip planes. The relation between dislocation structure and creep behavior is also assessed.

Raj, S. V.↗

Inhomogeneous deformation in INCONEL 718 during monotonic and cyclic loadings

The paper concentrates on the relation between microstructural observations of the dislocation structures and the macroscopic deformation responses of both aged and homogenized precipitate-hardened alloys at room temperature. The deformation responses are compared to the cyclic deformation response of an aged precipitate-hardened alloy. Early in the deformation, one deformation band per grain and little evidence of work hardening are observed; with increased deformation, work hardening begins, more bands nucleate, and their spacing becomes similar to that in the aged material. It is pointed out that the degree of coarseness of inhomogeneous deformation is not a result of a softening process within the bands due to precipitate shearing, but it is a function of the amount of work hardening within the bands.

Worthem, D. W.↗

Deformation mechanisms of NiAl cyclicly deformed near the brittle-to-ductile transformation temperature

One of the ongoing challenges of the aerospace industry is to develop more efficient turbine engines. Greater efficiency entails reduced specific strength and larger temperature gradients, the latter of which means higher operating temperatures and increased thermal conductivity. Continued development of nickel-based superalloys has provided steady increases in engine efficiency and the limits of superalloys have probably not been realized. However, other material systems are under intense investigation for possible use in high temperature engines. Ceramic, intermetallic, and various composite systems are being explored in an effort to exploit the much higher melting temperatures of these systems. NiAl is considered a potential alternative to conventional superalloys due to its excellent oxidation resistance, low density, and high melting temperature. The fact that NiAl is the most common coating for current superalloy turbine blades is a tribute to its oxidation resistance. Its density is one-third that of typical superalloys and in most temperature ranges its thermal conductivity is twice that of common superalloys. Despite these many advantages, NiAl requires more investigation before it is ready to be used in engines. Binary NiAl in general has poor high-temperature strength and low-temperature ductility. On-going research in alloy design continues to make improvements in the high-temperature strength of NiAl. The factors controlling low temperature ductility have been identified in the last few years. Small, but reproducible ductility can now be achieved at room temperature through careful control of chemical purity and processing. But the mechanisms controlling the transition from brittle to ductile behavior are not fully understood. Research in the area of fatigue deformation can aid the development of the NiAl system in two ways. Fatigue properties must be documented and optimized before NiAl can be applied to engineering systems. More importantly though, probing the deformation mechanisms operating in fatigue will lead to a better understanding of NiAl's unique characteristics. Low cycle fatigue properties have been reported on binary NiAl in the past year, yet those studies were limited to two temperature ranges: room temperature and near 1000 K. Eventually, fatigue property data will be needed for a wide range of temperatures and compositions. The intermediate temperature range near the brittle-to-ductile transition was chosen for this study to ascertain whether the sharp change occurring in monotonic behavior also occurs under cyclic conditions. An effort was made to characterize the dislocation structures which evolved during fatigue testing and comment on their role in the deformation process.

Antolovich, Stephen D.↗

Isothermal fatigue mechanisms in Ti-based metal matrix composites

Stress-controlled isothermal fatigue experiments were performed at room temperature (RT) and 548 C (in argon) on (0)8 SCS6/Ti 15-3 metal matrix composites (MMC's) with 15 and 41 volume percent SCS6 (SiC) fibers. The primary objectives were to evaluate the mechanical responses, and to obtain a clear understanding of the damage mechanisms leading to failure of the MMC's. The mechanical data indicated that strain ranges attained fairly constant values in the stress-controlled experiments at both RT and 538 C, and remained so for more than 85 percent of life. The fatigue data for MMC's with different volume fraction fibers showed that MMC life was controlled by the imposed strain range rather than the stress range. At RT, and at low and intermediate strain ranges, the dominant fatigue mechanism was matrix fatigue, and this was confirmed metallurgically from fractographic evidence as well as from observations of channel type dislocation structures in the matrix of fatigued MMC specimens. Reaction-zone cracks acted as important crack initiating sites at RT, with their role being to facilitate slip band formation and consequent matrix crack initiation through classical fatigue mechanisms. MMC life agreed with matrix life at the lower strain ranges, but was smaller than matrix life at higher strain ranges. Unlike the case of monotonic deformation, debonding damage was another major damage mechanism during fatigue at RT, and it increased for higher strain ranges. At high strain ranges at RT, fractography and metallography showed an absence of matrix cracks, but long lengths of debonds in the outer layers of the SCS6 fibers. Such debonding and consequent rubbing during fatigue is believed to have caused fiber damage and their failure at high strain ranges. Thus, whereas life was matrix dominated at low and intermediate strain ranges, it was fiber dominated at high strain ranges. At 538 C, the mean stain constantly increased (ratchetting) with the number of cycles. At high strain ranges, such ratchetting led to overload failure of the fibers, and debonding of the type at RT was very small. At intermediate strain ranges, fractography showed large areas of matrix cracks. However, in spite of this matrix dominated mechanism, the MMC life at elevated temperatures was significantly less than the matrix fatigue life at all strain ranges. The reason for this difference is still unclear, although metallographic and fractographic evidences suggest that internal crack initiation sites at Mo-ribbons and reaction-zone cracks may have played a critical role, with the former tending to dominate.

Majumdar, Bhaskar S.↗

Temperature dependence of strengthening mechanisms in the nanostructured ferritic alloy 14YWT: Part I

This paperpresentsexperimentalresultsonthemechanicalandmicrostructuralbehaviorsofthe nanostructuredferriticalloy14YWTandprovidesdiscussionrelevanttodeformationmechanismsover a widerangeoftemperature.Thetemperaturedependenceofstrengthwasinvestigatedoverawide temperaturerangeof 196 to1000 1C. Detailedmicrostructuralcharacterizationbeforeandafter deformationwasconductedtoobtainthekeyinformationondeformationmechanisms;microstruc- tural informationbeforeandaftertensiledeformation,includingcrystallographictexture,dislocation structures,andnanoclusters,wasobtainedfromthefocusedionbeamlift-outspecimensusingEBSD, TEM, andAPTtechniques.Multipledeformationstagescouldbeidentifiedintheyieldstrengthversus temperaturecurve.Thedislocationstructuresinthespecimensdeformedatroomtemperatureandat 900 1C werefoundtobesignificantlydifferent.EBSDresultswereusedtoelucidatechangesinthe crystallographictexturesofthespecimensbeforeandafterdeformationat900 1C.

Byun, Thak Sang↗

MICROSTRUCTURAL SUMMARY OF ODS FERRITIC ALLOYS (14YW, 14YWT, 12YWT, MA957FR, PM2000) AND RAFM STEELS (F82H MOD.3-CW, EUROFER97) FROM JP27 IN-SITU HE INJECTION (ISHI) EXPERIEMNT AT 500C

A TEM characterization of various ferritic based alloys has been conducted to document the changes in the microstructure under neutron irradiation and the impact of high levels of He injection. Microstructural features such as dislocation loops, network dislocations, He bubbles and voids were characterized in five ODS alloys, 14YW, 14YWT, 12YWT, MA957Fr, PM2000, and two RAFM steels, F82H mod.3+CW and Eurofer. The total neutron dose was 21.2 dpa and the total He levels were 1230 appm injected into an ~6 µm uniform region below the surface of the sample. The results indicated that He injection has a profound impact on the microstructural evolution of these alloys, producing dramatic changes in the dislocation structure and cavity distribution that are closely related to the size, density and chemistry of the oxide particles, or the lack thereof in the case of the RADM alloys.

dual He and neutron irradiation↗

ASSESSMENT OF DEFORMATION MECHANISMS IN NEUTRON-IRRADIATED ACCIDENT-TOLERANT FeCrAl ALLOYS VIA IN SITU MECHANICAL TESTING AND TEM ANALYSIS

Iron-chromium-aluminum (FeCrAl) alloys are promising as an accident-tolerant fuel cladding for loss-of-coolant accident scenarios; however, limited data are available on acting deformation mechanisms for this class of materials after neutron irradiation. Here, in situ tensile test experiments were conducted with specimens irradiated at ~1.8 dpa at typical light water reactor temperatures. Selected regions of interest were examined at different strain levels, aiming to investigate the impact of irradiation on acting deformation mechanisms. The fine material microstructure was investigated via transmission electron microscopy. Dislocation structure, radiation-induced defects, and α'-phase morphology were investigated in detail and compared with scanning electron microscopy-electron backscatter diffraction and mechanical test results.

Gussev, Maxim N.↗

Electronic structure study of screw dislocation core energetics in Aluminum and core energetics informed forces in a dislocation aggregate

Here we use a real-space formulation of orbital-free DFT to study the core energetics and core structure of an isolated screw dislocation in Aluminum. Using a direct energetics based approach, we estimate the core size of a perfect screw dislocation to be ≈ 7 |b|, which is considerably larger than previous estimates of 1–3 |b| based on displacement fields. The perfect screw upon structural relaxation dissociates into two Shockley partials with partial separation distances of 8.2 Å and 6.6 Å measured from the screw and edge component differential displacement plots, respectively. Similar to a previous electronic structure study on edge dislocation, we find that the core energy of the relaxed screw dislocation is not a constant, but strongly dependent on macroscopic deformations. Next, we use the edge and screw dislocation core energetics data with physically reasonable assumptions to develop a continuum energetics model for an aggregate of dislocations that accounts for the core energy dependence on macroscopic deformations. Further, we use this energetics model in a discrete dislocation network, and from the variations of the core energy with respect to the nodal positions of the network, we obtain the nodal core force which can directly be incorporated into discrete dislocation dynamics frameworks. We analyze and classify the nodal core force into three different contributions based on their decay behavior. Two of these contributions to the core force, both arising from the core energy dependence on macroscopic deformations, are not accounted for in currently used discrete dislocation dynamics models which assume the core energy to be a constant excepting for its dependence on the dislocation line orientation. Using case studies involving simple dislocation structures, we demonstrate that the contribution to the core force from the core energy dependence on macroscopic deformations can be significant in comparison to the elastic Peach–Koehler force even up to distances of 10–15 nm between dislocation structures. Thus, these core effects, whose origins are in the electronic structure of the dislocation core, can play an important role in influencing dislocation-dislocation interactions to much larger distances than considered heretofore.

36 MATERIALS SCIENCE↗

Atomic and electronic structure of Lomer dislocations at CdTe bicrystal interface

Extended defects are of considerable importance in determining the electronic properties of semiconductors, especially in photovoltaics (PVs), due to their effects on electron-hole recombination. We employ model systems to study the effects of dislocations in CdTe by constructing grain boundaries using wafer bonding. Atomic-resolution scanning transmission electron microscopy (STEM) of a [1–10]/ (110) 4.8° tilt grain boundary reveals that the interface is composed of three distinct types of Lomer dislocations. Geometrical phase analysis is used to map strain fields, while STEM and density functional theory (DFT) modeling determine the atomic structure at the interface. The electronic structure of the dislocation cores calculated using DFT shows significant mid-gap states and different charge-channeling tendencies. Cl-doping is shown to reduce the midgap states, while maintaining the charge separation effects. In conclusion, this report offers novel avenues for exploring grain boundary effects in CdTe-based solar cells by fabricating controlled bicrystal interfaces and systematic atomic-scale analysis.

36 MATERIALS SCIENCE↗

Creep behavior of 316 L stainless steel manufactured by laser powder bed fusion

Additive manufacturing as a new processing technique can produce unique microstructure that is difficult to achieve using conventional techniques. Here, we have investigated the creep behavior of 316 L stainless steel produced by a laser powder bed fusion process at temperatures of 550, 600 and 650 °C and stresses between 175 and 300 MPa. We found that additively-manufactured 316 L stainless steel had a higher stress dependence of the minimum creep rate than conventionally-made Type 316 SS, which could be attributed to the dislocation cell structure resulting from the printing process. The dislocation cell structure was unstable under creep, evolving into a uniform dislocation structure under the test conditions. While internal porosity in AM 316 L SS may serve as nucleation sites of creep voids and may be responsible for a relatively lower creep life, additively-manufactured 316 SS did not show inferior creep ductility when compared with conventionally-made 316 SS. The creep life of AM 316 L SS could be improved by stabilizing dislocation cell structure and/or reducing internal porosity through an optimized additive manufacturing process.

316 L stainless steel↗

Polymorphic structure of $\langle a \rangle$-type screw dislocation cores in $\alpha$-Ti

The dislocation core structure has a significant role in determining the dominant slip plane and the magnitude of the Peierls stress for a dislocation. An important challenge when studying dislocation cores is to determine the stable and metastable core morphologies, and then relate these structures to the dynamics of the dislocations. ere this study introduces a method for identifying core structures that are metastable at zero temperature. Application of this method to $\langle$a$\rangle$-type screw dislocations in α-Ti (as described using an empirical potential) reveals a multitude of (meta)stable nonplanar cores. Molecular dynamics studies show how the competing metastable core structures determine the properties of the dislocations at temperature and under a range of non-Schmid stresses.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dynamics of threading dislocations in porous heteroepitaxial GaN films

Behavior of threading dislocations in porous heteroepitaxial gallium nitride (GaN) films has been studied using computer simulation by the two-dimensional discrete dislocation dynamics approach. A computational scheme, where pores are modeled as cross sections of cylindrical cavities, elastically interacting with unidirectional parallel edge dislocations, which imitate threading dislocations, is used. Time dependences of coordinates and velocities of each dislocation from dislocation ensembles under investigation are obtained. Visualization of current structure of dislocation ensemble is performed in the form of a location map of dislocations at any time. It has been shown that the density of appearing dislocation structures significantly depends on the ratio of area of a pore cross section to area of the simulation region. In particular, increasing the portion of pores surface on the layer surface up to 2% should lead to about a 1.5-times decrease of the final density of threading dislocations, and increase of this portion up to 15% should lead to approximately a 4.5-times decrease of it.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Exploring the relation between transonic dislocation glide and stacking fault width in FCC metals

Theory predicts limiting gliding velocities that dislocations cannot overcome. Computational and recent experiments have shown that these limiting velocities are soft barriers and dislocations can reach transonic speeds in high rate plastic deformation scenarios. In this paper we systematically examine the mobility of edge and screw dislocations in several face centered cubic (FCC) metals (Al, Au, Pt, and Ni) in the extreme large-applied-stress regime using molecular dynamics simulations. Our results show that edge dislocations are more likely to move at transonic velocities due to their high mobility and lower limiting velocity than screw dislocations. Importantly, among the considered FCC metals, the dislocation core structure determines the dislocation’s ability to reach transonic velocities. This is likely due to the variation in stacking fault width due to relativistic effects near the limiting velocities.

36 MATERIALS SCIENCE↗