Search NASA⌕ Search

SEARCH · Search NASA

Results for “Drivetrain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11

A Lightweight, Direct-Drive, Fully Superconducting Generator for Large Wind Turbines

The current trend in the offshore wind turbine industry favors direct-drive generators based on permanent magnets, as they allow for a simple and reliable drivetrain without a gearbox. These generators, however, do not scale very well to high power levels beneficial for offshore wind, and their use in wind turbines over 6 MW is questionable in terms of mass and economic feasibility. Moreover, rare earth materials composing the permanent magnets are becoming less available, more costly and potentially unavailable in the foreseeable future. A stated goal of the DOE is a critical materials strategy that pursues the development of substitute materials and technology for rare earth materials to improve supply chain flexibility and meet the needs of the clean energy economy.Therefore, alternative solutions are needed, in terms of both favorable up-scaling and minimizing or eliminating the use of permanent magnets. The generator design presented in this document addresses both these issues with the development of a fully superconducting generator (FSG) with unprecedented high specific torque. A full-scale, 10-MW, 10-rpm generator will weigh less about 150 metric tons, compared to 300 metric tons for an equivalent direct-drive, permanent magnet generator. The developed concept does not use any rare earth materials in its critical drive components, but rather relies on a superconductor composed of mainly magnesium and boron (MgB2), both of which are in abundant supply from multiple global sources.

17 WIND ENERGY↗

A Disruptive Approach to Electric Vehicle Power Electronics Final Report

This project developed and demonstrated a new power electronics technology for electric vehicle drivetrains, that achieved significant improvements in power density and efficiency over standard drive cycles, relative to the commercial state of the art. In particular, the prototype measured loss and efficiency curves demonstrated a reduction in total loss over the US EPA US06 drive cycle by a factor of four. Similar reductions are observed for urban (UDDS) and highway (HWFET) drive cycles. Further, the project demonstrated a significant reduction in the total film capacitor requirements, by over an order of magnitude; this was achieved through fundamental improvements in converter circuit topologies. These nonincremental technology advances can lead to significant improvements in temperature rise, reliability, cost, and cooling system size and weight. These results were achieved through a new proposed composite converter architecture, and were demonstrated in a boost-type system similar to that employed by Toyota, Ford, and Honda. A 30 kW silicon prototype achieved a US06 average efficiency of 97.5%, which represents a reduction in average loss by a factor of approximately four relative to the 92.5% average efficiency of the commercial state of the art. A silicon carbide prototype achieved similar efficiency, while also achieving power densities of 23 kW/L (volumetric) and 20 kW/kg (gravimetric) in a boost dc-dc system including magnetics and film capacitors. This was achieved with a SiC switching frequency of 240 kHz, which allowed employment of planar magnetics. These power densities are roughly four times better than the commercial state of the art, and significantly exceed the DOE APEEM 2020 goals. In addition to the composite boost system, a SiC inverter was demonstrated at the 800 V 30 kW level. This inverter was demonstrated driving a permanent magnet machine over the US 06 drive cycle. The replacement of 1200 V Si IGBTs with 1200 V SiC MOSFETs led to improvement of CAFE average efficiency from 98.7% to 99.5%, which corresponds to a reduction of average loss by a factor of approximately two. The modular nature of the composite converter architecture opens the possibility of reuse of one or more converter modules during charging operations, providing a path for onboard charging capability at significant power levels while significantly reducing the volume and weight of the added charger module. This project demonstrated an integrated Level II charger whose add-on specific weight was approximately four times better than the DOE PHEV charger 2022 targets.

33 ADVANCED PROPULSION SYSTEMS↗

Gearbox Instrumentation for the Investigation of Bearing Axial Cracking

Failures in gearbox bearings have been the primary source of reliability issues for wind turbine drivetrains, leading to costly downtime and unplanned maintenance. The most common failure mode is attributed to so-called axial cracks or white-etching cracks, which primarily affect the intermediate and high-speed-stage bearings. The high-speed-shaft and bearing loads and sliding will be measured with a specially instrumented gearbox installed in a 1.5-megawatt turbine at the National Wind Technology Center in an upcoming test campaign. Additional instrumentation will also measure the tribological environment of these bearings, including bearing temperatures, lubricant temperature and water content, air temperature and humidity, and stray electrical current across the bearings. This paper fully describes the instrumentation package and summarizes initial results.

17 WIND ENERGY↗

Investigation of Roller Sliding in Wind Turbine Gearbox High-Speed-Shaft Bearings

In a collaborative project, Flender Corporation, SKF, and the National Renewable Energy Laboratory (NREL) have instrumented a commercial drivetrain, installed it in a wind turbine at the National Wind Technology Center, and operated the turbine for more than a year. The gearbox was specifically instrumented to measure high-speed bearing loads, sliding, and the lubricant environment. Commercial SKF black-oxide coated cylindrical-roller bearings were modified by magnetizing one roller and inserting a metal pin in the cage next to it to measure roller and cage speed, respectively, with an inductive coil and a proximity switch. In this report, these measurements are used to validate two different modeling approaches for bearing sliding - one analytical dynamic model and one multibody model. Once validated, these models can be used to evaluate the roller slip losses or cumulative frictional energy that are considered potential driving factors for wind turbine gearbox high-speed-shaft and high intermediate speed shaft bearing failures by white etching cracks.

17 WIND ENERGY↗

Emerging magnetic materials for electric vehicle drive motors [Slides]

Increasing demand for electric vehicles (EVs) is increasing demand for the permanent magnets that drive their motors, as approximately 80% of modern EV drivetrains rely on high-performance permanent magnets to convert electricity into torque. In turn, these high-performance permanent magnets rely on rare earth elements for their magnetic properties. These elements are "critical" (i.e., at risk of limiting the growth of renewable energy technologies such as EVs), which motivates an exploration for alternative materials. In this article, we overview the relevant fundamentals of permanent magnets, describe commercialized and emerging materials, and add perspective on future areas of research. Currently, the leading magnetic material for EV motors is Nd 2 Fe 14 B, with samarium-cobalt compounds (SmCo 5 and Sm 2 Co 17 ) providing the only high-performing commercialized alternative. Emerging materials that address criticality concerns include Sm 2 Fe 17 N 3 , Fe 16 N 2 , and the L10 structure of FeNi, which use lower cost elements that produce similar magnetic properties. However, these temperature-sensitive materials are incompatible with current metallurgical processing techniques. We provide perspective on how advances in low-temperature synthesis and processing science could unlock new classes of high-performing magnetic materials for a paradigm shift beyond rare earth-based magnets. In doing so, we explore the question: What magnetic materials will drive future EVs?

42 ENGINEERING↗

Gearbox Reliability Collaborative Phase 1 and 2: Testing and Modeling Results; Preprint

The Gearbox Reliability Collaborative (GRC) investigates root causes of wind turbine gearbox premature failures and validates design assumptions that affect gearbox reliability using a combined testing and modeling approach. Knowledge gained from the testing and modeling of the GRC gearboxes builds an understanding of how the selected loads and events translate into internal responses ofthree-point mounted gearboxes. This paper presents some testing and modeling results of the GRC research during Phase 1 and 2. Non-torque loads from the rotor including shaft bending and thrust, traditionally assumed to be uncoupled with gearbox, affect gear and bearing loads and resulting gearbox responses. Bearing clearance increases bearing loads and causes cyclic loading, which couldcontribute to a reduced bearing life. Including flexibilities of key drivetrain subcomponents is important in order to reproduce the measured gearbox response during the tests using modeling approaches.

17 WIND ENERGY↗

Investigating Main and High-Speed Shaft Bearing Reliability through Uptower Testing

The most prevalent failure modes in wind turbine drivetrains are main bearing failures stemming from micropitting, white etching or axial cracks in gearbox bearings, and generator bearing failures. These failures are neither well understood nor accounted for in design standards; consequently, the mitigation strategies being developed and fielded may only partially address the physics of failure and can take years to assess. The U.S. Department of Energy continues to support research programs to investigate the influence of rolling element sliding on the formation of bearing axial cracks and main bearing micropitting.

17 WIND ENERGY↗

Dynamometer Specifications at the National Wind Technology Center

The National Wind Technology Center features three dynamometers that can perform research validation on wind turbine systems from 1 kW to 5 MW. The dynamometers replicate realistic operational conditions to assess drivetrain designs and increase the technical readiness of innovations.

17 WIND ENERGY↗

Wind Energy Modeling and Simulation, Volume 2: Turbine and System

In order to optimise the yield of wind power from existing and future wind plants, the entire breadth of the system of a plant, from the wind field to the turbine components, needs to be modelled in the design process. The modelling and simulation approaches used in each subsystem as well as the system-wide solution methods to optimize across subsystem boundaries are described in this reference. Chapters are written by technical experts in each field, describing the current state of the art in modelling and simulation for wind plant design. This comprehensive, two-volume research reference will provide long-lasting insight into the methods that will need to be developed for the technology to advance into its next generation. Volume 2 covers turbine level aerodynamics, aeroelasticity, rotors drivetrains and electrical systems, wind turbine control, offshore foundations, system optimization, and grid modelling.

17 WIND ENERGY↗

Intracycle RPM control for vertical axis wind turbines

The wind energy market is currently dominated by horizontal axis wind turbines (HAWTs); however, vertical axis wind turbines (VAWTs) are emerging as a design alternative, especially for deep-water offshore siting due to their low center of gravity, ease of access to drivetrain components, and overall simplicity. Due to the absence of a pitch mechanism in large-scale Darrieus VAWTs, stall control has often been used to manage power and loads. Introducing a pitching mechanism in H-type VAWTs has been studied, but this diminishes the mechanical simplicity advantage, and the use of a pitching mechanism in a large-scale Darrieus-type VAWT is not practical. This work examines an innovative, alternative method to control the rotor dynamics of a large-scale 5 MW VAWT to maximize power while constraining loads without introducing any new or complex mechanical elements. This control strategy is termed intracycle revolution per minute (RPM) control, where the rotational speed of the turbine is allowed to vary in an optimal fashion with the azimuthal location of blades as opposed to typical constant RPM operation. An optimization framework is formulated for an open-loop optimal control problem and solved to maximize power subject to constraints on aerodynamic design loads. Results are presented to demonstrate the benefits and the performance limits of intracycle RPM control for large-scale 5 MW Darrieus VAWTs, namely, (1) power production (quantified in terms of AEP) that can be increased subject to baseline load limits and (2) opportunities to significantly increase AEP or decrease loads via intracycle RPM control that are examined for both two-bladed and three-bladed VAWTs.

17 WIND ENERGY↗

Inhibition of Micro-pitting by Tribofilm-Forming ZrO 2 Nanocrystal Lubricant Additives: A Micro-pitting Rig and Transmission Electron Microscope Study

The drive to reduce fuel consumption in transportation has encouraged the emergence of low viscosity lubricants to reduce viscous losses in the engine, drivetrain, and other components. However, viscosity reduction increases the risk of surface damage, thus motivating the development of new anti-wear (AW) additives. Capped ZrO 2 nanocrystals (NCs) in base oils have been shown to form AW tribofilms within microscale sliding contacts. However, the potential of ZrO 2 NCs to protect surfaces subjected to rolling-sliding contact from macroscale damage, such as micro-pitting, remains unexplored. Here, we explore the ability of ZrO 2 NCs to form protective tribofilms under harsh conditions using a micro-pitting rig (MPR), consisting of a three ring-on-roller configuration. The experiments were conducted in polyalphaolephin (PAO) base oil, with and without 5 nm diameter ZrO 2 NCs, at two levels of slide-to-roll ratio (SRR) (30% and 0%) and at variable test durations up to long durations (119 h). MPR results showed the use of ZrO 2 NCs gives rise to the formation of a tribofilm covering the roller surfaces and decreases the initiation and propagation of micro-pits compared to tests in pure PAO base stock. Transmission electron microscopy (TEM) performed on focused ion beam (FIB) milled cross-sectional samples of the roller surfaces revealed the growth of dense and 50–100 nm thick ZrO 2 -based tribofilms independent of (SRR), indicating the potential for robust micro-pitting fatigue protection. Nevertheless, small cracks localized within the near surface region of the roller tested at the most severe conditions (30% SRR and 119 h) were observed. The initiation of these cracks was directly related to the presence of manganese sulphide (MnS) inclusions in the steel, revealed using TEM combined with energy dispersive spectroscopy (EDS). Furthermore, the results highlight the benefits of the protective tribofilms formed by ZrO 2 NCs and suggest approaches for further optimizing their use.

36 MATERIALS SCIENCE↗

Performance and cost of fuel cells for off-road heavy-duty vehicles

Hydrogen fuel cell-powered off-road vehicles can replace hydrocarbon-powered off-road vehicles to reduce carbon dioxide and criteria pollutant emissions in the agriculture, construction, and mining industries. Vehicle manufacturers and customers recognize health and environmental benefits of emissions reductions but are ultimately compelled by the total cost of ownership of their vehicles. In this study, we conduct a technoeconomic evaluation for three hallmark off-road vehicles, tractors, wheel loaders, and excavators, comparing vehicles with hydrogen fuel cell + battery hybrid powertrains to traditional diesel powertrains. Stakeholder-valued performance metrics include fuel cell engine power, engine durability, hydrogen consumption rate, hydrogen storage system volume, and energy-regenerative drivetrain efficiency. The total cost of ownership includes capital, operating and maintenance, fuel, and fuel storage costs. State-of-the-art fuel cell powered wheel loaders and excavators are currently cost competitive with diesel platforms. If targeted improvements to cost, performance, and durability improvements of fuel cell stacks and storage systems are achieved, fuel cell systems would be cost competitive for tractors and significantly lower total cost of ownership options for wheel loaders and excavators.

33 ADVANCED PROPULSION SYSTEMS↗

Aluminum addition to AISI 52100 steel: Initial assessment on impact to mechanical properties and tribological performance and pathways for improvement

Here, in the transportation industry, reducing component weight is an effective strategy to improve fuel efficiency and lower emissions. Martensitic AISI 52100 steel is commonly used in drivetrain bearing components due to its high strength and excellent tribological performance. To achieve lightweighting without sacrificing mechanical properties and tribological behavior, this study explored the 52100 steel alloy modified by introducing nominally 5 wt% aluminum. The addition of aluminum led to an approximately 6% density reduction, however, it resulted in reduced hardness, strength and wear resistance, in part due to stabilization of a substantial amount of ferrite, as suggested by microstructural examination. Introducing 0.15 wt% additional carbon reduced the ferrite and demonstrated feasibility of mitigating the mechanical and tribological degradation caused by aluminum. This case study provides fundamental insights into the balance between lightweighting and mechanical/tribological performance for steel alloys, serving as a reference for further development of lightweight bearing steels.

Aluminum addition↗

Rare‐Earth Reduction in High‐Speed PM‐Assisted Synchronous Reluctance Motors Using Hybrid Magnet Strategies and Design Optimisation for 800 V EVs

The trend towards electrifying transportation systems has stimulated research endeavours aimed at developing electric machines that are not only high speed and efficient but also low‐cost and compact. To support this transition, the US Department of Energy (DOE) has established ambitious targets of $7/kW cost and 12 kW/L power density for the electric drivetrains. This paper attempts to meet these targets by proposing high‐speed permanent magnet assisted synchronous reluctance machine (PMASynRM) topologies enabled by hybrid magnet strategies, combining rare‐earth (RE) magnets with low‐cost, RE‐free alternatives. Modified 2‐layer and 3‐layer U‐shaped rotor configurations, featuring structural reinforcements to withstand high mechanical stress at elevated speeds, are developed. A multi‐objective design optimisation framework is employed to optimise the rotor design, targeting reductions in RE magnet volume, magnet demagnetisation risk and torque ripple while achieving the desired electromagnetic performance. A comprehensive analysis of the optimised rotor designs, compared against a 16,000 rpm, 800 V baseline IPM motor, shows over 70% RE reduction, demagnetisation risk below 3.5% and torque ripple under 10%. Detailed analyses of performance trends across various magnet combinations and rotor configurations highlight the viability of hybrid magnet PMASynRM designs as cost‐effective, robust and energy‐efficient solutions for next‐generation EVs.

33 ADVANCED PROPULSION SYSTEMS↗

Wind Turbine Design Optimization for Hydrogen Production

To help meet the need for inexpensive green fuels, we are working on wind turbine design optimization specifically for hydrogen production. We have thus far achieved a 1.53% decrease in LCOH as compared to a turbine optimized for LCOE using the same code, design variables, and models. We accomplished this by optimizing some components of the wind turbine tower, rotor, and drivetrain design with hydrogen production and costs in the design loop.

hydrogen↗

Automated Electric Vehicle Fleet Operations for On-Demand Service: Challenges and Opportunities

Automated/autonomous vehicle fleet operations within automated mobility districts have been studied over the past five years by the National Renewable Energy Laboratory, a US Department of Energy federally funded research and development center. This paper extends the analysis in this third phase of research underway to include considerations for electric vehicle operations and charging within a fleet of right-sized automated vehicles providing on-demand public mobility services. The current focus of research is on the operational complexities and associated challenges for automated/autonomous vehicles employing electric drivetrains and the resultant need for an efficient battery charging process while vehicles are operating in an "on-demand" mode of service. The blossoming of microtransit with shared-ride and point-to-point dispatching of each vehicle instills complex operations, with multiple mobility-on-demand transit operating sites being deployed, studied, and analyzed across North America. As a starting point, the authors' experience over the past 20 years with the analysis of automated transit network systems operating on and within dedicated and protected transitways provides initial insights into the system-level operational implications for maintaining a sufficient battery charge for a fleet of automated vehicles. Lessons learned through the prior analyses of automated transit network systems operating in on-demand service are identified, along with the capital cost implications for the requisite operating fleet size and charging station infrastructure for various approaches. These costs are summarized in juxtaposition with the benefits of realizing the higher goals of reducing environmental impacts and energy use within automated mobility districts as automated/autonomous vehicle technology matures. Finally, the discussion addresses key aspects of battery-electric propulsion for managed fleets in fully automated operation that will be studied as the third phase of research continues.

ADVANCED PROPULSION SYSTEMS↗

Non-steady wind turbine response to daytime atmospheric turbulence

Relevant to drivetrain bearing fatigue failures, we analyse non-steady wind turbine responses from interactions between energy-dominant daytime atmospheric turbulence eddies and the rotating blades of a GE 1.5 MW wind turbine using a unique dataset from a GE field experiment and computer simulation. Time-resolved local velocity data were collected at the leading and trailing edges of an instrumented blade together with generator power, revolutions per minute, pitch and yaw. Wind velocity and temperature were measured upwind on a meteorological tower. The stability state and other atmospheric conditions during the field experiment were replicated with a large-eddy simulation in which was embedded a GE 1.5 MW wind turbine rotor modelled with an advanced actuator line method. Both datasets identify three important response time scales: advective passage of energy-dominant eddies (≈25–50 s), blade rotation (once per revolution (1P), ≈3 s) and sub-1P scale (<1 s) response to internal eddy structure. Large-amplitude short-time ramp-like and oscillatory load fluctuations result in response to temporal changes in velocity vector inclination in the aerofoil plane, modulated by eddy passage at longer time scales. Generator power responds strongly to large-eddy wind modulations. Lastly, we show that internal dynamics of the blade boundary layer near the trailing edge is temporally modulated by the non-steady external flow that was measured at the leading edge, as well as blade-generated turbulence motions.

17 WIND ENERGY↗