Search NASA⌕ Search

SEARCH · Search NASA

Results for “Electrolytic Dissolution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Power and energy capacity tradeoffs in an all-aqueous copper thermally regenerative ammonia battery

Thermally regenerative ammonia batteries (TRABs) can provide energy storage and produce electrical power from low-grade waste heat instead of electricity. The use of all-aqueous copper-based electrolytes has recently produced higher power densities than those achieved using previous TRAB approaches based on reversible metal deposition and dissolution processes, but further gains are possible in power and energy density. We investigated the limitations of power and energy density and how they are impacted by the electrolyte composition and discharge currents. By increasing the ammonia concentration from 1 to 5 M, the power density of the battery increased from 11.2 to 28.5 mW cm –2 , but the energy density decreased from 0.56 to 0.31 Wh L –1 . Increasing discharge current densities from 4 to 12.5 mA cm –2 increased the average power density during discharge from 2.4 to 5.9 mW cm –2 without appreciable losses in energy density. Increasing the copper concentration from 0.1 to 0.5 M increased both energy density to 2.15 Wh L –1 and energy efficiency to 2.2% but did not substantially impact the power density. Furthermore, these results represent the highest performance metrics achieved for a low-grade waste heat to electricity system.

25 ENERGY STORAGE↗
DOE OSTI2020

Solid Electrolytes for Li–S Batteries: Solid Solutions of Poly(ethylene oxide) with Li x PON- and Li x SiPON-Based Polymers

We report here efforts to synthesize free-standing, dry polymer electrolytes that exhibit superior ionic conductivities at ambient for Li–S batteries. Co-dissolution of poly(ethylene oxide) (PEO) (M n 900k) with Li x PON and Li x SiPON polymer systems at a ratio of approximately 3:2 followed by casting provides transparent, solid-solution films 25–50 μm thick, lowering PEO crystallinity, and providing measured impedance values of 0.1–2.8 × 10 –3 S/cm at ambient. These values are much higher than simple PEO/Li + salt systems. These solid-solution polymer electrolytes (PEs) are (1) thermally stable to 100 °C; (2) offer activation energies of 0.2–0.5 eV; (3) suppress dendrite formation; and (4) enable the use of lithium anodes at current densities as high as 3.5 mAh/cm 2 . Here, galvanostatic cycling of SPAN/PEs/Li cell (SPAN = sulfurized, carbonized polyacrylonitrile) shows discharge capacities of 1000 mAh/g sulfur at 0.25C and 800 mAh/g sulfur at 1C with high coulumbic efficiency over 100 cycles.

25 ENERGY STORAGE↗
DOE OSTI2023

Electrolyte Engineering Stabilizes Photoanodes Decorated with Molecular Catalysts

Molecular catalysts are promising oxygen evolution promoters in conjunction with photoanodes for solar water splitting. Maintaining the stability of both photoabsorber and cocatalyst is still a prime challenge, with many efforts tackling this issue through sophisticated material designs. Such approaches often mask the importance of the electrode-electrolyte interface and overlook easily tunable system parameters, such as the electrolyte environment, to improve efficiency. We provide a systematic study on the activity-stability relationship of a prominent Fe 2 O 3 photoanode modified with Ir molecular catalysts using in situ mass spectroscopy. After gaining detailed insights into the dissolution behavior of the Ir cocatalyst, a comprehensive pH study is conducted to probe the impact of the electrolyte on the performance. An inverse trend in Fe and Ir stability is found, with the best activity-stability synergy obtained at pH 9.7. The results bring awareness to the overall photostability and electrolyte engineering when advancing catalysts for solar water splitting.

14 SOLAR ENERGY↗
DOE OSTI2024

Accurately constituting robust interfaces for high-performance high-energy lithium metal batteries

High-energy lithium metal batteries (LMBs) have received ever-increasing interest. Among them, coupling lithium metal (Li) with nickel-rich material, LiNi x Mn y Co z O 2 (NMCs, x ≥ 0.6, x + y + z = 1), is promising because Li anodes enable an extremely high capacity (∼3860 mA h g −1 ) and the lowest redox potential (−3.04 V vs. standard hydrogen electrode), while NMCs can achieve a much higher capacity of ∼200 mA h g −1 and lower cost than those of LiCoO 2 . However, the resultant Li‖NMC cells have been hindered from commercialization due to a series of challenges related to the interface stability of both Li anodes and NMC cathodes. Specifically, Li anodes suffer from Li dendritic growth and the formation of solid electrolyte interphase (SEI), while NMC cathodes suffer from the formation of cathode electrolyte interphase (CEI) and other interface-related issues, including transition metal dissolution, oxygen release, cracking, and so on. To tackle these issues, recently, two sister techniques, atomic and molecular layer deposition (ALD and MLD), have emerged and exhibit tremendous capabilities to accurately constitute robust interfaces to achieve high-performance Li‖NMC LMBs. They can uniquely develop uniform and conformal films as surface coatings of LMBs in a precisely controllable mode at the atomic/molecular level, while proceeding with film deposition at low temperatures (e.g., ≤250 °C). In this Feature Article, we review the latest research progress in developing novel surface coatings via ALD and MLD for Li‖NMC LMBs and discuss outcomes for pursuing high performance.

25 ENERGY STORAGE↗
NASA NTRS1969

Self-discharge in bimetallic cells containing alkali metal

Theoretical analysis of thermally regenerative bimetallic cells with alkali metal anodes shows a relation between the current drawn and the rate of discharge under open-circuit conditions. The self-discharge rate of the cell is due to the dissolution and ionization of alkali metal atoms in the fused-salt electrolyte

Foster, M. S.↗
DOE OSTI2020

Long-Term Cyclability of NCM-811 at High Voltages in Lithium-Ion Batteries: an In-Depth Diagnostic Study

High-nickel layered oxides, such as LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NCM-811), offer higher energy density than their low-nickel counterparts at a given voltage and are gaining major traction in automotive lithium-ion batteries for electric vehicles. Besides high-Ni content, higher charging voltages above 4.3 V vs Li + /Li boost the energy and represent another focus in battery development. Here, we investigate the long-term cyclability of NCM-811 in graphite pouch cells over 1000 deep cycles between 2.5–4.2, 2.5–4.4, and 2.5–4.5 V through a suite of sensitive characterization techniques. The NCM-811 full cells show severely deteriorated cyclability with higher charging voltages, from 78% at 4.2 V to 52 and 32% at 4.4 and 4.5 V, respectively. At 4.2 V, minor parasitic electrolyte oxidation as well as cathode Li/Ni mixing and cracking are revealed after cycling, while transition-metal dissolution and surface reconstruction into rock-salt NiO are virtually undetectable. At 4.4 and 4.5 V, transition-metal dissolution and crossover to the anode become much more pronounced and a primary contributor to the capacity fade, while significant surface NiO formation causes substantial voltage polarization, which is less noticeable at 4.2 V. Meanwhile, more severe electrolyte oxidation, Li/Ni mixing, and particle pulverization exacerbate the voltage and capacity fade. Finally, these results outline distinct challenges for stable high-Ni layered oxide cathodes in high-voltage Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Highly Stable and Conductive 1,3‐Dioxolane/Hydrocarbon Based Electrolyte Solvent for Advanced Lithium‐Sulfur Batteries

Abstract Developing effective electrolytes is crucial for boosting the performance of Lithium‐Sulfur (LiS) rechargeable battery. Recent improvements in electrolyte formulations have enhanced cyclability by increasing electrochemical stability at the electrode interfaces. However, achieving both high ionic conductivity (σ) and stability at these interfaces simultaneously remains a significant challenge. In this study, we utilized a strategy to suppress polysulfide dissolution by employing a mixture of 1,3‐dioxolane (DOL) and hydrocarbon solvents with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) electrolyte salt. Compared to the conventional electrolyte solution, which is 1 M LiTFSI salt in a 50/50 vol % mixture of DOL and dimethoxy ethane (DME), the LiTFSI electrolyte with DOL/hydrocarbon solvents demonstrate better cycling stability, compatibility with the Li‐metal anode, and a high specific discharge capacity (Csp). Among the various DOL/hydrocarbon and LiTFSI electrolyte salts, the combination of DOL and n‐hexane, a linear hydrocarbon, with LiTFSI electrolyte salt, (DnH40LiTFSI) exhibits remarkable σ (6.5×10 −3 S/cm at 30 °C), compatibility with the Li‐metal anode, an initial Csp of ca. 1264 mAh/g, cycling stability (Csp and Coulombic efficiency are 811 mAh/g and 98.09 % after 120 cycles) at 0.1 C by forming a good protective layer on the Li‐metal surface and preventing polysulfide dissolution.

Ahmed, Faiz↗
DOE OSTI2022

Li Morphology Evolution during Initial Cycles in a Gel Composite Polymer Electrolyte

Understanding and controlling lithium morphology evolution and lithium dendrite formation and growth during cycling is one of the key challenges for high-energy lithium metal batteries. This challenge applies to liquid electrolyte batteries as well as solid-state and semi-solid-state batteries. Our current knowledge about the evolution of the Li morphology is mostly obtained from liquid electrolyte-based studies in a Li–Li symmetrical cell configuration. The knowledge obtained in such conditions may not readily transfer into solid-state or semi-solid-state batteries. In this work, Li morphology evolution during initial cycling in a full cell configuration with the LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NMC 622) cathode and a semi-solid-state gel composite electrolyte is monitored via post-mortem photographs and scanning electron microscopy at multiple length scales. The gel composite electrolyte contains a cross-linked poly(ethylene oxide)-based polymer electrolyte, ceramic fillers, and a liquid plasticizer. The results show that severe surface pitting occurs as early as the second stripping cycle. Pit formation and continuous dissolution during the stripping process are the main cause of the Li surface roughening and dendrite growth mechanism in the model gel composite electrolyte. Comparing Li dendrite growth mechanisms in liquid, polymer, and ceramic solid electrolytes, the dendrite growth mechanism observed in this model electrolyte resembles that of the liquid electrolyte the most. This study suggests that strategies to control Li morphology and prevent dendrite growth in a gel composite electrolyte should be similar to strategies applicable to liquid electrolytes.

25 ENERGY STORAGE↗
DOE OSTI2020

A Micelle Electrolyte Enabled by Fluorinated Ether Additives for Polysulfide Suppression and Li Metal Stabilization in Li-S Battery

The Li-S battery is a promising next-generation technology due to its high theoretical energy density (2600 Wh kg -1 ) and low active material cost. However, poor cycling stability and coulombic efficiency caused by polysulfide dissolution have proven to be major obstacles for a practical Li-S battery implementation. In this work, we develop a novel strategy to suppress polysulfide dissolution using hydrofluoroethers (HFEs) with bi-functional, amphiphlic surfactant-like design: a polar lithiophilic "head" attached to a fluorinated lithiophobic "tail." A unique solvation mechanism is proposed for these solvents whereby dissociated lithium ions are readily coordinated with lithiophilic "head" to induce self-assembly into micelle-like complex structures. Complex formation is verified experimentally by changing the additive structure and concentration using small angle X-ray scattering (SAXS). These HFE-based electrolytes are found to prevent polysulfide dissolution and to have excellent chemical compatibility with lithium metal: Li||Cu stripping/plating tests reveal high coulombic efficiency (>99.5%), modest polarization, and smooth surface morphology of the uniformly deposited lithium. Li-S cells are demonstrated with 1395 mAh g-1 initial capacity and 71.9% retention over 100 cycles at >99.5% efficiency-evidence that the micelle structure of the amphiphilic additives in HFEs can prohibit polysulfide dissolution while enabling facile Li + transport and anode passivation.

25 ENERGY STORAGE↗
DOE OSTI2021

Long-term cyclability of Li 4 Ti 5 O 12 /LiMn 2 O 4 cells using carbonate-based electrolytes for behind-the-meter storage applications

Li 4 Ti 5 O 12 /LiMn 2 O 4 (LTO/LMO) chemistry was evaluated as a potential candidate for behind-the-meter storage (BTMS) applications. Its long-term cycle performance at 45 °C was tested using ethylene carbonate (EC) and propylene carbonate (PC) solvent electrolytes. Over 1000 cycles, LTO/LMO cells exhibited ~80% capacity retention and Coulombic efficiency higher than 99.96%. Electrochemical test results showed the major degradation mode of LTO/LMO cells arises from continuous electrolyte decomposition at the LTO anode and loss of Li inventory. EC and PC electrolytes created distinct surface layers, where the EC reduction products were more effective in passivating the LTO electrode surface. Dissolution and migration of Mn from the cathode was probed as Mn 2+ species distributed throughout the surface layer at the anode. By utilizing a prelithiated LTO electrode, the LTO/LMO cell performance was significantly enhanced with EC electrolyte. On the other hand, PC electrolyte resulted in accelerated electrolyte decomposition at the lithiated LTO surface due to the lack of surface passivation. Thus, mitigating parasitic reactions at the LTO electrode is the key to developing successful LTO/LMO cells.

25 ENERGY STORAGE↗
DOE OSTI2021

An in situ generated polymer electrolyte via anionic ring-opening polymerization for lithium–sulfur batteries

The use of solid polymer electrolytes has previously proven to be an effective approach to address the lithium polysulfide dissolution and high electrode interfacial impedance of Li–S batteries via an in situ polymerization process. However, the conventional in situ synthesis employs a cationic ring-opening polymerization (CROP) of 1,3-dioxolane (DOL) catalyzed by a strong Lewis acid. New polymerization chemistry that is more compatible with Li–S chemistry needs to be developed to mitigate the disadvantages associated with the CROP process. Herein we report a new approach to in situ polymerize a set of new episulfide monomers in solution with LiTFSI salt via an anionic ring-opening polymerization (AROP). This new polymer system takes advantage of the inherent cell chemistry present in the Li–S cell through the nucleophilic lithium sulfides which are generated during the initial discharge cycle and act as the initiator for the polymerization. Additionally, their presence was shown to initiate the monomer solvents through AROP with no need for additional catalysts, rather than the more commonly utilized cationic systems which require an external Lewis acid catalyst. This work offers an important pathway toward in situ polymer electrolytes for Li–S batteries and offers a new avenue of exploration for polymer electrolyte synthesis.

25 ENERGY STORAGE↗
DOE OSTI2023

Li–Mn–O Li-rich cation disordered rock-salt cathode materials do not undergo reversible oxygen redox during cycling

An in-depth study of “Li 4 Mn 2 O 5 ”, a nanocomposite of Li 2 O and Li 4-x Mn 2 O 5 with a disordered rock salt structure (LMO), was conducted to determine the origins of the observed anomalously high charge and discharge capacity in lithium cells, which can exceed 350 mA h g -1 . Using soft and hard X-ray absorption spectroscopy (XAS), mapping of resonant inelastic X-ray scattering (mRIXS), and X-ray Raman spectroscopy (XRS), it was determined that electrochemical decomposition of Li 2 O upon charge and reduction of Mn to below 3+ during discharge is responsible for the capacities that are observed, with no evidence of contributions from reversible oxygen redox. Here, the over-reduction is exacerbated when charging limits of 4.5–4.8 V are used due to side reactions between electrolytic solution and the highly oxidized active material. These side reactions result in dissolution of Mn at room temperature and release of oxygen and other gases during initial cycles, which, in turn, cause rapid capacity fading. This is accompanied by evolution of the voltage profile upon cycling towards one that resembles that of manganese oxide spinels. The cycling behavior can be improved somewhat by reducing the upper voltage limit, although this results in a diminishment of the discharge capacities below 200 mA h g -1 . By adding various amounts of spinel LiMn 2 O 4 during synthesis, it was possible to produce LMOs with rock salt structures having significantly improved cycling behavior but still having capacities in excess of 250 mA h g -1 . An optimized modified material also exhibits better rate capability and much less gas evolution during initial cycles than the unmodified LMO. Interestingly, as-made modified materials generally exhibited lower than expected average Mn oxidation states attributable to oxygen loss during the synthesis process, as well as higher capacities than expected based on their manganese contents. The oxygen loss during processing may reduce the activity of the remaining oxygen and account for the lower reactivity of the spinel-modified material.

25 ENERGY STORAGE↗
DOE OSTI2020

Transition-Metal Dissolution from NMC-Family Oxides: A Case Study

In this work we investigated the static reactions of highly delithiated Li(Ni 1/3 Mn 1/3 Co 1/3 )O 2 , Li(Ni 0.5 Mn 0.3 Co 0.2 )O 2 , Li(Ni 0.6 Mn 0.2 Co 0.2 )O 2 , and Li(Ni 0.8 Mn 0.1 Co 0.1 )O 2 positive electrodes with 2,3-butanedione and with tetrabutyl ammonium bifluoride as model leaching agents. In the bifluoride trials, it was found that [Ni] in the leachate was proportional to X Co ( X Ni ) 3 , where X M is the ideal stoichiometry in the bulk oxide, and inversely proportional to ( X Mn ) 2 ; [Mn] to X Co ( X Ni ); and [Co] to X Co . The relationships between metal concentrations and stoichiometry may indicate that nickel, as a next-nearest neighbor on the positive electrode surface, can make dissolution more favorable in some instances.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Structural and Electrochemical Impacts of Mg/Mn Dual Dopants on the LiNiO 2 Cathode in Li-Metal Batteries

Doping chemistry has been regarded as an efficient strategy to overcome some fundamental challenges facing the “no-cobalt” LiNiO 2 cathode materials. By utilizing the doping chemistry, we evaluate the battery performance and structural/chemical reversibility of a new no-cobalt cathode material (Mg/Mn-LiNiO 2 ). The unique dual dopants drive Mg and Mn to occupy the Li site and Ni site, respectively. We report the Mg/Mn-LiNiO 2 cathode delivers smooth voltage profiles, enhanced structural stability, elevated self-discharge resistance, and inhibited nickel dissolution. As a result, the Mg/Mn-LiNiO 2 cathode enables improved cycling stability in lithium metal batteries with the conventional carbonate electrolyte: 80% capacity retention after 350 cycles at C /3, and 67% capacity retention after 500 cycles at 2 C (22 °C). We then take the Mg/Mn-LiNiO 2 as the platform to investigate the local structural and chemical reversibility, where we identify that the irreversibility takes place starting from the very first cycle. The highly reactive surface induces the surface oxygen loss, metal reduction reaching the subsurface, and metal dissolution. Our data demonstrate that the dual dopants can, to some degree, mitigate the irreversibility and improve the cycling stability of LiNiO 2 , but more efforts are needed to eliminate the key challenges of these materials for battery operation in the conventional carbonate electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2024

Structure and Dynamics of Aqueous Electrolytes at Quartz (001) and (101) Surfaces

Here, understanding and describing reactivity at mineral-water interfaces such as ion adsorption, the kinetics of dissolution, or surface charge development depends on our ability to improve the accuracy of electrical double layer (EDL) models. While molecular dynamics (MD) simulations are routinely used to investigate the structure and energetics of adsorbed ions comprising the EDL, less attention is paid to their self-diffusion dynamics, which can uniquely inform on coupling to interfacial reactions. Here we use MD to investigate both the organization and diffusion dynamics of water and electrolyte ions (NaCl, KCl, CaCl 2 ) at hydroxylated quartz (001) and (101) surfaces, a comparison which allowed us to assess surface structural effects of corrugation and silanol density. We found that inner- versus outer-sphere complex formation depends on cation size and charge but not necessarily hydration energies. Participation of surface silanols in the hydration spheres of Na + and K + generally indicated their preference for inner-sphere complexation, but this depends strongly on the orientation of the surface considered through its influence over the organization and dynamics of adsorbed water layers. In particular, surface orientation substantially affects the diffusive behavior of the near-surface water. Na + was found to decrease the mobility of water in the first layer, consistent with an increasing frequency of hydrolysis implied by faster quartz dissolution rates observed in experiments via the well known salt effect. Our results are also in good agreement with the observed dissolution rate of quartz vs. surface adsorption strength measure by Dove and Nix. This study sets the stage for a forthcoming paper examining how the dynamics at quartz/electrolyte interfaces are influenced by externally applied electric fields.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2023

Multiphysics Modeling of Electrode Dissolution under Hydrodynamic Conditions in Low Conductivity Water

Efficient plug-flow electrochemical reactors are characterized by their ability to effectively convert species with significant ionic strength and/or with the assistance of a well-behaved electrolyte. Because of the classic electroconductivity requirement, electrochemical reactors are not particularly attractive options for applications with low-conductivity conditions, especially for low-pressure feeds. However, these reactors can still find application in dedicated processes such as ultra-clean water conditioning and biological-coupled separation systems. Consequently, a multi-physics model was developed using COMSOL Multiphysics to characterize different reactor-design conditions based on the Tertiary Current Distribution which accounts for the effects of expected variations in electrolyte composition and ionic strength on the electrochemical process, as well as solution resistance and electrode kinetics. The modelling framework presented here employs single-phase laminar fluid flow, the Nernst-Planck equation, the water-based electroneutrality condition, and concentration-dependent overpotentials. This investigation particularly explores the electrolysis process of “anodic dissolution,” in which elemental species dissociate from the solid matrix of the electrode and enter the liquid phase of the electrolyte as soluble ions. The reactor configuration of interest has a rectangular parallel-electrode design and is operated galvanostatically. A series of parametric studies are carried out to inspect the response of the system when hydrodynamic, kinetic, and geometric conditions are changed. The parametric sweep resulted in variable effluent concentrations and system voltage, which reveal underlaying optimization patterns for electrode dissolution in low conductivity water.

Multiphysics↗
DOE OSTI2023

Improving the Long-term Cycle Performance of xLi 2 MnO 3 ·(1-x)LiMeO 2 /Li 4 Ti 5 O 12 Cells via Prelithiation and Electrolyte Engineering

Toward the development of high energy density and long lifetime batteries for behind-the-meter storage (BTMS) applications, Li- and Mn-rich layered oxide cathode (xLi 2 MnO 3 ·(1-x)LiMeO 2 , Me = Ni, Mn, and etc., LMR-NM) and Li 4 Ti 5 O 12 (LTO) anode system was examined. To mitigate the major degradation mechanisms at each electrode (i.e., loss of Li inventory (LLI) at the anode and transition metal dissolution and oxygen release at the cathode), two approaches were taken—prelithiating the LTO electrode and varying the electrolyte solvent compositions. The effect of prelithiation and electrolyte engineering on the long-term cycle performance of LMR-NM/LTO cells were systematically evaluated via electrochemical analyses and post-mortem characterizations. By using a prelithiated LTO anode and supplying additional Li to the system, the capacity retention of LMR-NM/LTO system was improved. The degree of enhancement was dependent on the types of electrolytes used, as their decomposition products determined the level of LLI. With increased capacity retention, however, the cathode was utilized to a greater extent, resulting in more severe loss of the cathode active material. Thus, all degradation mechanisms should be considered comprehensively when designing high performance LMR-NM/LTO cells to account for their complex interplay.

25 ENERGY STORAGE↗