Search NASA⌕ Search

SEARCH · Search NASA

Results for “Exhaust”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Operational implications of a cloud model simulation of space shuttle exhaust clouds in different atmospheric conditions

A three-dimensional cloud model was used to characterize the dominant influence of the environment on the Space Shuttle exhaust cloud. The model was modified to accept the actual heat and moisture from rocket exhausts and deluge water as initial conditions. An upper-air sounding determined the ambient atmosphere in which the cloud would grow. The model was validated by comparing simulated clouds with observed clouds from four actual Shuttle launches. Results are discussed with operational weather forecasters in mind. The model successfully produced clouds with dimensions, rise, decay, liquid water contents, and vertical motion fields very similar to observed clouds whose dimensions were calculated from 16 mm film frames. Once validated, the model was used in a number of different atmospheric conditions ranging from very unstable to very stable. Wind shear strongly affected the appearance of both the ground cloud and vertical column cloud. The ambient low-level atmospheric moisture governed the amount of cloud water in model clouds. Some dry atmospheres produced little or no cloud water. An empirical forecast technique for Shuttle cloud rise is presented and differences between natural atmospheric convection and exhaust clouds are discussed.

Zak, J. A.↗
NASA NTRS1989

The effect of exhaust plume/afterbody interaction on installed scramjet performance

An upwind implicit Navier-Stokes code has been used to study hypersonic exhaust plume/afterbody flow fields. It is found that afterbody forces varied linearly with the nozzle exit pressure for moderately underexpanded jets, and that exhaust gases with low isentropic exponents (gamma) contribute up to 25 percent more force than high-gamma exhaust gases. Highly underexpanded jets are shown to create a strong plume shock, and the interaction of this shock with the afterbody produces a complicated pattern of crossflow separation.

Edwards, T. A.↗
NASA NTRS1991

Monitoring Engine Vibrations And Spectrum Of Exhaust

Real-time computation of intensities of peaks in visible-light emission spectrum of exhaust combined with real-time spectrum analysis of vibrations into developmental monitoring technique providing up-to-the-second information on conditions of critical bearings in engine. Conceived to monitor conditions of bearings in turbopump suppling oxygen to Space Shuttle main engine, based on observations that both vibrations in bearings and intensities of visible light emitted at specific wavelengths by exhaust plume of engine indicate wear and incipient failure of bearings. Applicable to monitoring "health" of other machinery via spectra of vibrations and electromagnetic emissions from exhausts. Concept related to one described in "Monitoring Bearing Vibrations For Signs Of Damage", (MFS-29734).

Martinez, Carol L.↗
NASA NTRS1990

Status report on a real time Engine Diagnostics Console for rocket engine exhaust plume monitoring

This paper describes the work done on the Engine Diagnostics Console during the past year of development at Stennis Space Center. The Engine Diagnostics Console (EDC) is a hardware and software package which provides near real time monitoring of rocket engine exhaust plume emissions during ground testing. The long range goal of the EDC development program is to develop an instrument that can detect engine degradation leading to catastrophic failure, and respond by taking preventative measures. The immediate goal for the past year's effort is the ability to process spectral data, taken from a rocket engine's exhaust plume, and to identify in an automated and high speed manner, the elemental species and multielemental materials that are present in the exhaust plume.

Bircher, F. E.↗
NASA NTRS1992

An analytical approach for the prediction of gamma-to-alpha phase transformation of aluminum oxide (Al2O3) particles in the Space Shuttle ASRM and RSRM exhausts

The analytical approach developed here utilizes the flow-field output from industry standard nozzle and plume codes as input into a particle phase conversion code which predicts the amount of gamma-to-alpha conversion in SRM exhausts. Sixty different cases were considered which varied such parameters as particle size, degree of undercooling, motor type, and altitude. On-centerline calculations were made for both the ASRM and RSRM at an altitude of 100,000 feet with particle sizes varying from 3.5 to 9.1 micron radius and undercooling varying from 0 to 20 percent. Additional calculations were made for the ASRM at 100,000 feet off centerline and at an altitude of 60,000 feet on centerline. The results indicate that significant amounts of metastable alumina will be present in ASRM and RSRM exhausts. Though not significant to motor performance, this may be important in such issues as environmental effects of rocket exhausts, plume radiative heating predictions, and particle size determination by laser scattering.

Oliver, S. M.↗
NASA NTRS1992

Planar laser-induced fluorescence imaging of OH in the exhaust of a bi-propellant thruster

Planar laser-induced fluorescence imaging of the hydroxyl radical has been performed on the flow produced by the exhaust of a subscale H2/O2 fueled bi-propellant rocket engine. Measurements were made to test the feasibility of OH (0,0) and (3,0) excitation strategies by using injection seeded XeCl and KrF excimer lasers, respectively. The flow is produced with hydrogen and oxygen reacting at a combustor chamber pressure of 5 atm which then exhausts to the ambient. The hydroxyl concentration in the exhaust flow is approximately 8 percent. Fluorescence images obtained by pumping the Q1(3) transition in the (0,0) band exhibited very high signals but also showed the effect of laser beam absorption. To obtain images when pumping the P1(8) transition in the (3,0) band it was necessary to use exceptionally fast imaging optics and unacceptably high intensifier gains. The result was single-shot images which displayed a signal-to-noise ratio of order unity or less when measured on a per pixel basis.

Paul, Phillip H.↗
NASA NTRS1993

Simulation of UV atomic radiation for application in exhaust plume spectrometry

Quantitative analysis of exhaust plume spectral data has long been a goal of developers of advanced engine health monitoring systems which incorporate optical measurements of rocket exhaust constituents. Discussed herein is the status of present efforts to model and predict atomic radiation spectra and infer free-atom densities from emission/absorption measurements as part of the Optical Plume Anomaly Detection (OPAD) program at Marshall Space Flight Center (MSFC). A brief examination of the mathematical formalism is provided in the context of predicting radiation from the Mach disk region of the SSME exhaust flow at nominal conditions during ground level testing at MSFC. Computational results are provided for Chromium and Copper at selected transitions which indicate a strong dependence upon broadening parameter values determining the absorption-emission line shape. Representative plots of recent spectral data from the Stennis Space Center (SSC) Diagnostic Test Facility (DTF) rocket engine are presented and compared to numerical results from the present self-absorbing model; a comprehensive quantitative analysis will be reported at a later date.

Wallace, T. L.↗
NASA NTRS1993

Effect of jet engine exhaust on SOFIA straylight performance

The Stratospheric Observatory For Infrared Astronomy (SOFIA) is being designed at NASA's Ames Research Center as a replacement for the Kuiper Airborne Observatory (KAO). A 2.5-m Nasmyth telescope will be mounted in a Boeing 747 SP and flown at 41,000 ft, above most of the H2O in the earth's atmosphere. In the original SOFIA design, the telescope is located in front of the wings, as it is in the KAO. An alternative design with the telescope placed behind the wings is being studied as part of an effort to reduce cost and weight. In this location, the emission from the engines and the hot H2O molecules in the exhaust become significant straylight sources. The engines and exhaust radiate into the telescope cavity, and illuminate the primary and tertiary mirrors at low telescope elevation angles. The APART/PADE program was used to analyze the straylight at the SOFIA focal plane as a function of wavelength and telescope elevation angle. The emission from the engines and exhaust gas is compared to that from the earth and the telescope itself. Based on the results of this analysis, the SOFIA telescope has been moved behind the wings.

St. Clair Dinger, Ann↗
NASA NTRS1950

Altitude Performance Characteristics of Turbojet-engine Tail-pipe Burner with Variable-area Exhaust Nozzle Using Several Fuel Systems and Flame Holders

A tail-pipe burner with a variable-area exhaust nozzle was investigated. From five configurations a fuel-distribution system and a flame holder were selected. The best configuration was investigated over a range of altitudes and flight Mach numbers. For the best configuration, an increase in altitude lowered the augmented thrust ratio, exhaust-gas total temperature, and tail-pipe combustion efficiency, and raised the specific fuel consumption. An increase in flight Mach number raised the augmented thrust ratio but had no apparent effect on exhaust-gas total temperature, tail-pipe combustion efficiency, or specific fuel consumption.

ENGINES, TURBOJET↗
NASA NTRS1954

A flow calorimeter for determining combustion efficiency from residual enthalpy of exhaust gases

A flow calorimeter for determining the combustion efficiency of turbojet and ram-jet combustors from measurement of the residual enthalpy of combustion of the exhaust gas is described. Briefly, the calorimeter catalytically oxidizes the combustible constituents of exhaust-gas samples, and the resultant temperature rise is measured. This temperature rise is related to the residual enthalpy of combustion of the sample by previous calibration of the calorimeter. Combustion efficiency can be calculated from a knowledge of the residual enthalpy of the exhaust gas and the combustor input enthalpy. An accuracy of +-0.2 Btu per cubic foot was obtained with prepared fuel-air mixtures, and the combustion efficiencies of single turbojet combustors measured by both the flow-calorimeter and heat-balance methods compared within 3 percentage units. Flow calorimetry appears to be a suitable method for determining combustion efficiencies at high combustor temperatures where ordinary thermocouples cannot be used. The method is fundamentally more accurate than heat-balance methods at high combustion efficiencies and can be used to verify near-100-percent efficiency data.

Evans, Albert↗
NASA NTRS1943

The Measurement of Fuel-Air Ratio by Analysis for the Oxidized Exhaust Gas

An investigation was made to determine a method of measuring fuel-air ratio that could be used for test purposes in flight and for checking conventional equipment in the laboratory. Two single-cylinder test engines equipped with typical commercial engine cylinders were used. The fuel-air ratio of the mixture delivered to the engines was determined by direct measurement of the quantity of air and of fuel supplied and also by analysis of the oxidized exhaust gas and of the normal exhaust gas. Five fuels were used: gasoline that complied with Army-Navy fuel Specification No. AN-VV-F-781 and four mixtures of this gasoline with toluene, benzene, and xylene. The method of determining the fuel-air ratio described in this report involves the measurement of the carbon-dioxide content of the oxidized exhaust gas and the use of graphs for the presented equation. This method is considered useful in aircraft, in the field, or in the laboratory for a range of fuel-air ratios from 0.047 to 0.124.

Gerrish, Harold C.↗
NASA NTRS1945

An Experimental Investigation of Rectangular Exhaust-Gas Ejectors Applicable for Engine Cooling

An experimental investigation of rectangular exhaust-gas ejector pumps was conducted to provide data that would serve as a guide to the design of ejector applications for aircraft engines with marginal cooling. The pumping characteristics of rectangular ejectors actuated by the exhaust of a single-cylinder aircraft engine were determined for a range of ejector mixing-section area from 20 to 50 square inches, over-all length from 12 to 42 inches, aspect ratio from 1 to 5, diffusing exit area from 20 to 81 square inches, and exhaust-nozzle aspect ratio from 1 to 42.

Manganiello, Eugene J↗
NASA NTRS1995

A computational environment for exhaust nozzle design

The Nozzle Design Associate (NDA) is a computational environment for the design of jet engine exhaust nozzles for supersonic aircraft. NDA may be used either to design new aircraft or to design new nozzles that adapt existing aircraft so they may be reutilized for new missions. NDA was developed in a collaboration between computer scientists at Rutgers University and exhaust nozzle designers at General Electric (GE) Aircraft Engines and General Electric Corporate Research and Development. The NDA project has two principal goals: to provide a useful engineering tool for exhaust nozzle design, and to explore fundamental research issues that arise in the application of automated design optimization methods to realistic engineering problems.

Gelsey, Andrew↗
NASA NTRS1996

Temperature, Pressure, and Infrared Image Survey of an Axisymmetric Heated Exhaust Plume

The focus of this research is to numerically predict an infrared image of a jet engine exhaust plume, given field variables such as temperature, pressure, and exhaust plume constituents as a function of spatial position within the plume, and to compare this predicted image directly with measured data. This work is motivated by the need to validate computational fluid dynamic (CFD) codes through infrared imaging. The technique of reducing the three-dimensional field variable domain to a two-dimensional infrared image invokes the use of an inverse Monte Carlo ray trace algorithm and an infrared band model for exhaust gases. This report describes an experiment in which the above-mentioned field variables were carefully measured. Results from this experiment, namely tables of measured temperature and pressure data, as well as measured infrared images, are given. The inverse Monte Carlo ray trace technique is described. Finally, experimentally obtained infrared images are directly compared to infrared images predicted from the measured field variables.

Nelson, Edward L.↗
NASA NTRS1995

Exhausted Plume Flow Field Prediction Near the Afterbody of Hypersonic Flight Vehicles in High Altitudes

A two-dimensional computer code to solve the Burnett equations has been developed which computes the flow interaction between an exhausted plume and hypersonic external flow near the afterbody of a flight vehicle. This Burnett-2D code extends the capability of Navier-Stokes solver (RPLUS2D code) to include high-order Burnett source terms and slip-wall conditions for velocity and temperature. Higher-order Burnett viscous stress and heat flux terms are discretized using central-differencing and treated as source terms. Blocking logic is adopted in order to overcome the difficulty of grid generation. The computation of exhaust plume flow field is divided into two steps. In the first step, the thruster nozzle exit conditions are computed which generates inflow conditions in the base area near the afterbody. Results demonstrated that at high altitudes, the computations of nozzle exit conditions must include the effects of base flow since significant expansion exists in the base region. In the second step, Burnett equations were solved for exhaust plume flow field near the afterbody. The free stream conditions are set at an altitude equal to 80km and the Mach number is equal to 5.0. The preliminary results show that the plume expansion, as altitude increases, will eventually cause upstream flow separation.

Chou, Lynn Chen↗
NASA NTRS1959

Comparison of Rocket Performance using Exhaust Diffuser and Conventional Techniques for Altitude Simulation

A rocket engine with an exhaust-nozzle area ratio of 25 was operated at a constant chamber pressure of 600 pounds per square inch absolute over a range of oxidant-fuel ratios at an altitude pressure corresponding to approximately 47,000 feet. At this condition, the nozzle flow is slightly underexpanded as it leaves the nozzle. The altitude simulation was obtained first through the use of an exhaust diffuser coupled with the rocket engine and secondly, in an altitude test chamber where separate exhauster equipment provided the altitude pressure. A comparison of performance data from these two tests has established that a diffuser used with a rocket engine operating at near-design nozzle pressure ratio can be a valid means of obtaining altitude performance data for rocket engines.

Sivo, Joseph N.↗
NASA NTRS1999

Static Performance of a Fixed-Geometry Exhaust Nozzle Incorporating Porous Cavities for Shock-Boundary Layer Interaction Control

An investigation was conducted in the model preparation area of the Langley 16-Foot Transonic Tunnel to determine the internal performance of a fixed-geometry exhaust nozzle incorporating porous cavities for shock-boundary layer interaction control. Testing was conducted at static conditions using a sub-scale nozzle model with one baseline and 27 porous configurations. For the porous configurations, the effects of percent open porosity, hole diameter, and cavity depth were determined. All tests were conducted with no external flow at nozzle pressure ratios from 1.25 to approximately 9.50. Results indicate that baseline nozzle performance was dominated by unstable, shock-induced, boundary-layer separation at over-expanded conditions. Porous configurations were capable of controlling off-design separation in the nozzle by either alleviating separation or encouraging stable separation of the exhaust flow. The ability of the porous nozzle concept to alternately alleviate separation or encourage stable separation of exhaust flow through shock-boundary layer interaction control offers tremendous off-design performance benefits for fixed-geometry nozzle installations. In addition, the ability to encourage separation on one divergent flap while alleviating it on the other makes it possible to generate thrust vectoring using a fixed-geometry nozzle.

Asbury, Scott C.↗