Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLAT PLATE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 199 records · Page 11
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Thermal protection system gap heating rates of the Rockwell International flat plate heat transfer model (OH2A/OH2B)

Heat transfer data for the Rockwell International Flat Plate Thermocouple Model are presented. The model simulated the Space Shuttle Vehicle Thermal Protection System. Data were recorded for locations in and around various size gaps for various gap orientation configurations. The test was conducted at Mach 5.1 for free-stream Reynolds number per foot values from 500,000 to 1,500,000.

Foster, T. F.↗
NASA NTRS1979

Wind Loads on Flat Plate Photovoltaic Array Fields

The aerodynamic forces resulting from winds acting on flat plate photovoltaic arrays were investigated. Local pressure distributions and total aerodynamic forces on the arrays are shown. Design loads are presented to cover the conditions of array angles relative to the ground from 20 deg to 60 deg, variable array spacings, a ground clearance gap up to 1.2 m (4 ft) and array slant heights of 2.4 m (8 ft) and 4.8 m (16 ft). Several means of alleviating the wind loads on the arrays are detailed. The expected reduction of the steady state wind velocity with the use of fences as a load alleviation device are indicated to be in excess of a factor of three for some conditions. This yields steady state wind load reductions as much as a factor of ten compared to the load incurred if no fence is used to protect the arrays. This steady state wind load reduction is offset by the increase in turbulence due to the fence but still an overall load reduction of 2.5 can be realized. Other load alleviation devices suggested are the installation of air gaps in the arrays, blocking the flow under the arrays and rounding the edges of the array. A wind tunnel test plan to supplement the theoretical study and to evaluate the load alleviation devices is outlined.

Miller, R.↗
NASA NTRS1986

Flat-plate solar array project. Volume 6: Engineering sciences and reliability

The Flat-Plate Solar Array (FSA) Project activities directed at developing the engineering technology base required to achieve modules that meet the functional, safety, and reliability requirements of large scale terrestrial photovoltaic systems applications are reported. These activities included: (1) development of functional, safety, and reliability requirements for such applications; (2) development of the engineering analytical approaches, test techniques, and design solutions required to meet the requirements; (3) synthesis and procurement of candidate designs for test and evaluation; and (4) performance of extensive testing, evaluation, and failure analysis of define design shortfalls and, thus, areas requiring additional research and development. A summary of the approach and technical outcome of these activities are provided along with a complete bibliography of the published documentation covering the detailed accomplishments and technologies developed.

Ross, R. G., Jr.↗
NASA NTRS1987

Performance improvements in silicon flat-plate cells and modules

This paper reports the development of a flat-plate module based on highly efficient ion-implanted silicon solar cells. The cells developed in this work are 53 sq cm in area and have exhibited AM 1.5 efficiencies of over 18 percent. The use of back surface reflectors to reduce module operating temperature is discussed. A comparison of various approaches to cell design is made, and module test data for these designs are presented. A comparison of float zone and Czochralski silicon is made. Module efficiency of over 15 percent (at 25 C) is reported.

Spitzer, M. B.↗
NASA NTRS1990

The stability of a three-dimensional laminar boundary layer on a swept flat plate

The linear stability of the laminar boundary layer on a swept flat plate with an imposed favorable pressure gradient was studied utilizing a linear stability model which accounts for streamline curvature for three-dimensional incompressible flows. Calculations were performed for an effective leading-edge sweep angle of 42.5 degrees and freestream velocity of 19 m/s. Computed disturbance amplification rates for the spectrum of amplified frequencies and wavelengths for stationary crossflow vortices were compared with experimental results.

Collier, F. S., Jr.↗
NASA NTRS1990

The stability of a three dimensional laminar boundary layer over a swept flat plate

The linear stability of the laminar boundary layer on a swept flat plate with an imposed favorable pressure gradient was studied utilizing a linear stability model which accounts for streamline curvature for three-dimensional incompressible flows. Calculations were performed for a leading-edge sweep angle of 45 degrees and freestream valocity of 19 m/s. Computed disturbance amplification rates and wavelengths for stationary crossflow vortices were compared with available experimental results.

Mueller, B.↗
NASA NTRS2014

Flow Phenomena in the Very Near Wake of a Flat Plate with a Circular Trailing Edge

The very near wake of a flat plate with a circular trailing edge, exhibiting pronounced shedding of wake vortices, is investigated with data from a direct numerical simulation. The separating boundary layers are turbulent and statistically identical thus resulting in a wake that is symmetric in the mean. The focus here is on the instability of the detached shear layers, the evolution of rib-vortex induced localized regions of reverse flow that detach from the main body of reverse flow in the trailing edge region and convect downstream, and phaseaveraged velocity statistics in the very near wake. The detached shear layers are found to exhibit unstable behavior intermittently, including the development of shear layer vortices as in earlier cylinder flow investigations with laminar separating boundary layers. Only a small fraction of the separated turbulent boundary layers undergo this instability, and form the initial shed vortices. Pressure spectra within the shear layers show a broadband peak at a multiple of shedding frequency. Phase-averaged intensity and shear stress distributions of the randomly fluctuating component of velocity are compared with those obtained in the near wake. The distributions of the production terms in the transport equations for the turbulent stresses are also provided.

Turbulence↗